Polyelectrolyte‐grafted carbon nanotubes: Synthesis,reversible phase‐transition behavior,and tribological properties as lubricant additives

A novel polyelectrolyte‐grafted multiwalled carbon nanotubes (MWCNTs‐g‐PILs) which possesses a hard backbone of MWCNTs and a soft shell of brush‐like poly (ionic liquids) (PILs) has been synthesized via the surface atom transfer radical polymerization (ATRP). Chemical structure and the grafted PILs quantities of MWCNTs‐g‐PILs were determined by FTIR, TGA, and XPS. TEM and FE‐SEM observations indicate that the nanotubes were coated with a PILs layer, exhibiting core‐shell nanostructures with the PILs chains as the brush‐like or hairy shell and the MWCNTs as the hard backbone. Furthermore, the effect of counter‐anions on the solubility of MWCNTs‐g‐PILs was investigated. The results indicate that relative solubility of MWCNTs‐g‐PILs in various solvents could be switched by anion exchange. This tunable solubility results in the formation of the cycle of reversible phase‐transition. Tribological property of MWCNTs‐g‐PILs as additives in base lubricant 1‐methyl‐3‐butylimidaaolium hexafluorophosphate (LP104) was evaluated using an Optimol SRV oscillating friction and wear tester, confirming that MWCNTs‐g‐PILs are the excellent antiwear and friction‐reducing additives, which can amend the tribological properties of base lubricant significantly. This is attributed to the good dispersibility and core‐shell structure of MWCNTs‐g‐PILs. These results reported in this work may open primarily toward constructing a bridge among carbon nanotues (CNTs), ILs, and lubricant additives and secondarily to prove that CNTs (modified CNTs) as lubricant additives are promising candidates. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7225–7237, 2008     

Comparison of monomethoxy‐, dimethoxy‐, and trimethoxysilane anchor groups for surface‐initiated RAFT polymerization from silica surfaces

The immobilization of reversible addition–fragmentation chain transfer (RAFT) agents on silica for surface‐initiated RAFT polymerizations (SI‐RAFT) via the Z‐group approach was studied systematically in dependence of the functionality of the RAFT‐agent anchor group. Monoalkoxy‐, dialkoxy‐, and trialkoxy silyl ether groups were incorporated into trithiocarbonate‐type RAFT agents and bound to planar silica surfaces as well as to silica nanoparticles. The immobilization efficiency and the structure of the bound RAFT‐agent film varied strongly in dependence of the used solvent (toluene vs. 1,2‐dimethoxyethane) and the anchor group functionality, as evidenced by atomic force microscopy, transmission electron microscopy, dynamic light scattering, and UV/Vis spectroscopy. Surface‐initiated RAFT polymerizations using functionalized silica nanoparticles revealed that grafted oligomers, which often occur in SI‐RAFT, are not formed within the crosslinked structures that originate from the immobilization, and that RAFT‐agent films that show less aggregation during the immobilization are more efficient during SI‐RAFT in terms of polymer grafting density. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 103–113     

Synthesis of PNIPAM polymer brushes on reduced graphene oxide based on click chemistry and RAFT polymerization

Preparation and characterization of poly(N‐isopropylacrylamide) (PNIPAM) polymer brushes on the surfaces of reduced graphene oxide (RGO) sheets based on click chemistry and reversible addition‐fragmentation chain transfer (RAFT) polymerization was reported. RGO sheets prepared by thermal reduction were modified by diazonium salt of propargyl p‐aminobenzoate, and alkyne‐functionalized RGO sheets were obtained. RAFT chain transfer agent (CTA) was grafted to the surfaces of RGO sheets by click reaction. PNIPAM on RGO sheets was prepared by RAFT polymerization. Fourier transform‐infrared spectroscopy, thermogravimetric analysis, X‐ray photoelectron spectroscopy, and transmission electron microscopy (TEM) results all demonstrated that RAFT CTA and PNIPAM were successfully produced on the surfaces of RGO sheets. Nanosized PNIPAM domains on RGO sheets were observed on TEM. Micro‐DSC result indicated that in aqueous solution PNIPAM on RGO sheets presented a lower critical solution temperature at 33.2 °C. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of poly(methyl acrylate) loops grafted onto silica nanoparticles via reversible addition‐fragmentation chain transfer polymerization

Reversible addition‐fragmentation chain transfer (RAFT) polymerization was used to produce poly(methyl acrylate) (pMA) loops grafted onto silica nanoparticles using doubly anchored bifunctional RAFT agents 1,4‐bis(3′‐trimethoxysilylpropyltrithiocarbonylmethyl)benzene (Z‐group approach) and 1,6‐bis(o,p‐2′‐trimethoxysilylethylbenzyltrithiocarbonyl)hexane (R‐group approach) as mediators. In both cases, molecular weights of the resulting surface‐confined polymer loops increased with monomer conversion, whereas the grafting density was significantly higher in the case of the R‐group supported RAFT polymerization due to mechanistic differences of the RAFT process at the surface. This result was evident from thermogravimetric analysis and supported by scanning electron microscopy. Polymer loops with molecular weights up to 53,000 g mol^?1 were accessible with polydispersities of about 2.0 without and 1.5 with the addition of free RAFT agent. UV signals of the detached pMA loops measured via size exclusion chromatography were shifted to higher molecular weights compared with the corresponding RI signals, indicating branching reactions caused by the close proximity of growing radicals and polymer at the surface of the silica nanoparticles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7656–7666, 2008     

Polymer coating of carboxylic acid functionalized multiwalled carbon nanotubes via reversible addition‐fragmentation chain transfer mediated emulsion polymerization

In this work, successful polymer coating of COOH‐functionalized multiwalled carbon nanotubes (MWCNTs) via reversible addition fragmentation chain transfer (RAFT) mediated emulsion polymerization is reported. The method used amphiphilic macro‐RAFT copolymers as stabilizers for MWCNT dispersions, followed by their subsequent coating with poly(methyl methacrylate‐co‐butyl acrylate). Poly(allylamine hydrochloride) was initially used to change the charge on the surface of the MWCNTs to facilitate adsorption of negatively charged macro‐RAFT copolymer onto their surface via electrostatic interactions. After polymerization, the resultant latex was found to contain uniform polymer‐coated MWCNTs where polymer layer thickness could be controlled by the amount of monomer fed into the reaction. The polymer‐coated MWCNTs were demonstrated to be dispersible in both polar and nonpolar solvents. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Immobilization of RAFT agents on silica nanoparticles utilizing an alternative functional group and subsequent surface‐initiated RAFT polymerization

Silica–polystyrene core‐shell particles were successfully prepared by surface‐mediated reversible addition fragmentation chain transfer (RAFT) polymerization of styrene monomer from the surfaces of the silica‐supported RAFT agents. Initially, macro‐RAFT agents were synthesized by RAFT polymerization of γ‐methacryloxypropyltrimethoxysilane (MPS) in the presence of chain transfer agents (CTAs). Immobilization of CTAs onto the silica surfaces was then performed by reacting silica with macro‐RAFT agents via a silane coupling. Grafting of polymer onto silica forms core‐shell nanostructures and shows a sharp contrast between silica core and polymer shell in the phase composition. The thickness of grafted‐polymer shell and the diameter of core‐shell particles increase with the increasing ratio of monomer to silica. A control experiment was carried out by conventional free radical emulsion copolymerization of MPS‐grafted silica and styrene under comparable conditions. The resulting data provide further insight into the chemical composition of grafted‐polymers that are grown from the silica surface through RAFT process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 467–484, 2009     

RAFT‐mediated synthesis of poly[(oligoethylene glycol) methyl ether acrylate] brushes for biological functions

The synthesis of poly[(oligoethylene glycol) methyl ether acrylate] [poly(OEGA)] brushes was achieved via reversible addition‐fragmentation chain transfer (RAFT) polymerization and used to selectively immobilize streptavidin proteins. Initially, gold surfaces were modified with a trithiocarbonate‐based RAFT chain transfer agent (CTA) by using an ester reaction involving a gold substrate modified with 11‐mercapto‐1‐undecanol and bis(2‐butyric acid)trithiocarbonate. poly(OEGA) brushes were then prepared via RAFT‐mediated polymerization from the surface‐immobilized CTA. The immobilization of CTA on the gold surface and the subsequent polymer formation were followed by ellipsometry, X‐ray photoelectron spectroscopy, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and water contact‐angle measurements. RAFT‐mediated polymerization method gave CTA groups to grafted poly(OEGA) termini, which can be converted to various biofunctional groups. The terminal carboxylic acid groups of poly(OEGA) chains were functionalized with amine‐functionalized biotin units to provide selective attachment points for streptavidin proteins. Fluorescence microscopy measurements confirmed the successful immobilization of streptavidin molecules on the polymer brushes. It is demonstrated that this fabrication method may be successfully applied for specific protein recognition and immobilization. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A strategy for synthesis of ion‐bonded amphiphilic miktoarm star copolymers via supramolecular macro‐RAFT agent

Amphiphilic supramolecular miktoarm star copolymers linked by ionic bonds with controlled molecular weight and low polydispersity have been successfully synthesized via reversible addition‐fragmentation chain transfer (RAFT) polymerization using an ion‐bonded macromolecular RAFT agent (macro‐RAFT agent). Firstly, a new tetrafunctional initiator, dimethyl 4,6‐bis(bromomethyl)‐isophthalate, was synthesized and used as an initiator for atom transfer radical polymerization (ATRP) of styrene to form polystyrene (PSt) containing two ester groups at the middle of polymer chain. Then, the ester groups were converted into tertiary amino groups and the ion‐bonded supramolecular macro‐RAFT agent was obtained through the interaction between the tertiary amino group and 2‐dodecylsulfanylthiocarbonylsulfanyl‐2‐methyl propionic acid (DMP). Finally, ion‐bonded amphiphilic miktoarm star copolymer, (PSt)₂‐poly(N‐isopropyl‐acrylamide)₂, was prepared by RAFT polymerization of N‐isopropylacrylamide (NIPAM) in the presence of the supramolecular macro‐RAFT agent. The polymerization kinetics was investigated and the molecular weight and the architecture of the resulting star polymers were characterized by means of ¹H‐NMR, FTIR, and GPC techniques. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5805–5815, 2008     

Synthesis and characterization of polystyrene‐graphite nanocomposites via surface RAFT‐mediated miniemulsion polymerization

Graphite oxide (GO) was prepared and immobilized with dodecyl isobutyric acid trithiocarbonate (DIBTC) reversible addition‐fragmentation chain transfer (RAFT) agent. The hydroxyl groups of GO were attached to the DIBTC RAFT agent through an esterification process. The resultant modified GO was used for the preparation of polystyrene (PS)/graphite nanocomposites in miniemulsion polymerization. The RAFT‐grafted GO (GO‐DIBTC) at various loadings was dispersed in styrene monomer, and the resultant mixtures were sonicated in the presence of a surfactant (sodium dodecylbenzene sulfonate) and a hydrophobe (hexadecane) to form miniemulsions. The stable miniemulsions thus obtained were polymerized using azobisisobutyronitrile as the initiator to yield encapsulated PS‐GO nanocomposites. The molar mass and polydispersity index of PS in the nanocomposites depended on the amount of RAFT‐grafted GO in the system, in accordance with the features of the RAFT polymerization method. The PS‐GO nanocomposites were of exfoliated morphology, as confirmed by X‐ray diffraction and transmission electron microscopy measurements. The thermal stability and mechanical properties of the PS‐GO nanocomposites were better than those of the neat PS polymer. Furthermore, the mechanical properties were dependent on the modified GO content (i.e., the amount of RAFT‐grafted GO). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Isothermal and nonisothermal crystallization kinetics of nylon 6/functionalized multi‐walled carbon nanotube composites

The well dispersion of functionalized multi‐walled carbon nanotube (f‐MWCNT) in nylon 6 matrix was prepared by solution mixing techniques. The isothermal and nonisothermal crystallization kinetics of nylon 6 and nylon 6/f‐MWCNT nanocomposites were studied by differential scanning calorimetry (DSC), X‐ray diffraction and polarized optical microscopy analysis. DSC isothermal results revealed that the activation energy of nylon 6 extensively decreased by adding 1 wt % f‐MWCNT into nylon 6, suggesting that the addition of small amount of f‐MWCNT probably induces the heterogeneous nucleation. Nevertheless, the addition of more f‐MWCNT into nylon 6 matrix reduced the transportation ability of polymer chains during crystallization process and thus increased the activation energy. The nonisothermal crystallization of nylon 6/f‐MWCNT nanocomposites was also discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 158–169, 2008     

Effect of rate retardation in RAFT grafting polymerization from silicon wafer surface

Polystyrene and poly(butyl acrylate) were grafted from silicon wafer surface by reversible addition‐fragmentation chain transfer (RAFT) polymerization. Three RAFT agents were immobilized onto silicon wafer through their leaving/initiating groups (R group). Grafting polymerization of butyl acrylate (BA) and styrene (St) was then carried out from the immobilized RAFT agents. The immobilization of the RAFT agents and the subsequent grafting polymerization of St and BA were evaluated by ellipsometry and X‐ray photoelectron spectroscopy. It was found that type of monomer, structure of RAFT agent, and local RAFT concentration on the surface have dramatic influences on the thickness of grafted polymer layer. The grafting polymerization with more severe rate retardation effect yielded thinner polymer films on the silicon wafer. Selection of a RAFT agent with little rate retardation was critical in the grafting polymerization to achieve thick films. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 970–978, 2008     

“Click” coupling between alkyne‐decorated multiwalled carbon nanotubes and reactive PDMA‐PNIPAM micelles

Covalent functionalization of alkyne‐decorated multiwalled carbon nanotubes (MWNTs) with a well‐defined, azide‐derivatized, thermoresponsive diblock copolymer, poly(N,N‐dimethylacrylamide)‐poly(N‐isopropylacrylamide) (PDMA‐PNIPAM) was accomplished by the Cu(I)‐catalyzed [3 + 2] Huisgen cycloaddition. It was found that this reaction could simultaneously increase the molecular size and bonding density of grafted polymers when PDMA‐PNIPAM micelles were employed in the coupling system. On the other hand, attachment of molecularly dissolved unimers of high‐molecular weight onto the nanotube resulted in low‐graft density. The block copolymer bearing azide groups at the PDMA end was prepared by reversible addition–fragmentation transfer polymerization, which formed micelles with a diameter of ～40 nm at temperatures above its critical micelle temperature. Scanning electron microscopy was utilized to demonstrate that the coupling reaction was successfully carried out between copolymer micelles and alkyne‐bearing MWNTs. FTIR spectroscopy was utilized to follow the introduction and consumption of alkyne groups on the MWNTs. Thermogravimetric analysis indicated that the functionalized MWNTs consisted of about 45% polymer. Transmission electron microscopy was utilized to image polymer‐functionalized MWNTs, showing relatively uniform polymer coatings present on the surface of nanotubes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7187–7199, 2008     

The pH induced vesicle to micelle morphology transition of a THP‐protected polymer

A diblock copolymer consisting of tetrahydropyranyl acrylate (THPA) as a pH‐deprotectable block, and a permanently hydrophobic block, methyl acrylate, was synthesized by RAFT polymerization using a quaternary amine functionalized, hydrophilic, RAFT chain transfer agent. The polymer self‐assembled in water to form vesicles with D_h = 130 nm, as determined by DLS and cryogenic transmission electron microscopy. Acid catalyzed deprotection of the THPA units to yield acrylic acid resulted in a vesicle to micelle morphology transition, as evidenced by the decrease in hydrodynamic diameter to D_h = 19 nm and the observation of micelles by dry state transmission electron microscopy. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3026–3031     

Stability and utility of pyridyl disulfide functionality in RAFT and conventional radical polymerizations

Two RAFT agents, suitable for inducing living radical polymerization in water, have been synthesized. Both RAFT agents were shown to be effective over the temperature range 25–70 °C. One RAFT agent was functionalized with a pyridyl disulfide group. RAFT efficacy was demonstrated for the polymerizations of N‐isopropyl acrylamide (NIPAAM) and poly(ethylene oxide)‐acrylate (PEG‐A) in both water and acetonitrile. The kinetic data indicates that the pyridyl disulfide functionality is largely benign in free radical polymerizations, remaining intact for subsequent reaction with thiol groups. This result was confirmed by studying conventional radical polymerizations in the presence of hydroxyethyl pyridyl disulfide. The utility of the pyridyl disulfide functionality at the terminus of the polymers was demonstrated by synthesizing polymer‐BSA conjugates. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7207–7224, 2008     

Dendrimer‐star polymer and block copolymer prepared by reversible addition‐fragmentation chain transfer (RAFT) polymerization with dendritic chain transfer agent

A new reversible addition‐fragmentation chain transfer (RAFT) agent, dendritic polyester with 16 dithiobenzoate terminal groups, was prepared and used in the RAFT polymerization of styrene (St) to produce star polystyrene (PSt) with a dendrimer core. It was found that this polymerization was of living characters, the molecular weight of the dendrimer‐star polymers could be controlled and the polydispersities were narrow. The dendrimer‐star block copolymers of St and methyl acrylate (MA) were also prepared by the successive RAFT polymerization using the dendrimer‐star PSt as macro chain transfer agent. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6379–6393, 2005     

Synthesis and kinetics of graft polymerization of methyl methacrylate from the RAFT coordinated surface of nano‐TiO2

Polymer chains of PMMA were grown from nano titania (n‐TiO₂) by the reversible addition‐fragmentation chain transfer polymerization process. The mechanism and kinetics of MMA polymerization from both solution and “grafted from” n‐TiO₂ were studied. The RAFT agent, 4‐cyano‐4‐(dodecylsulfanylthiocarbonyl) sulfanyl pentanoic acid, with an available carboxyl group was used to anchor onto the n‐TiO₂ surface, with the S?C(SC₁₂H₂₅) moiety used for subsequent RAFT polymerization of MMA to form n‐TiO₂/PMMA nanocomposites. The functionalization of n‐TiO₂ was determined by FTIR, XPS, partitioning studies, and thermal analysis. The livingness of the polymerization was verified using NMR and GPC, while the dispersion of the inorganic filler in the polymer was studied using electron microscopy, FTIR, and thermal analysis. The monomer conversion and molecular weight kinetics were explored for the living RAFT polymerization, both in solution and grafted from n‐TiO₂, with first‐order kinetics being observed in both cases. Increased graft density on n‐TiO₂ led to a lower rate of polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3926–3937, 2008     

Oil‐Soluble Polymer Brush Grafted Nanoparticles as Effective Lubricant Additives for Friction and Wear Reduction

The development of high performance lubricants has been driven by increasingly growing industrial demands and environmental concerns. Herein, we demonstrate oil‐soluble polymer brush‐grafted inorganic nanoparticles (hairy NPs) as highly effective lubricant additives for friction and wear reduction. A series of oil‐miscible poly(lauryl methacrylate) brush‐grafted silica and titania NPs were synthesized by surface‐initiated atom transfer radical polymerization. These hairy NPs showed exceptional stability in poly(alphaolefin) (PAO) base oil; no change in transparency was observed after being kept at ?20, 22, and 100 °C for ≥55 days. High‐contact stress ball‐on‐flat reciprocating sliding tribological tests at 100 °C showed that addition of 1 wt % of hairy NPs into PAO led to significant reductions in coefficient of friction (up to ≈40 %) and wear volume (up to ≈90 %). The excellent lubricating properties of hairy NPs were further elucidated by the characterization of the tribofilm formed on the flat. These hairy NPs represent a new type of lubricating oil additives with high efficiency in friction and wear reduction.     

Enhancing dispersion of copper nanowires in melt‐mixed polystyrene composites

Copper nanowire (CuNWs)/polystyrene (PS) composites were prepared by melt mixing using unfunctionalized and functionalized nanowires. Alkanethiols were utilized to modify the surface of CuNWs postsynthesis and enable their dispersion in a polymer melt. Unfunctionalized nanowires decreased the electrical resistivity of PS by nine orders of magnitude with 2.0 vol % Cu, and resulted in composites with a viscoelastic behavior dominated by polymer–polymer networks indicating that electrical percolation occurred without a transition from liquid‐like to solid‐like behavior (i.e., rheological percolation). Results from transmission electron microscopy (TEM), scanning electron microscopy (SEM), and melt rheology characterization indicated that surface modification of CuNWs contributed to the dispersion of the nanofiller in the polymer matrix. CuNWs functionalized with 1‐octanethiol and 1‐butanethiol produced rheological percolation and a gradual decrease in the electrical resistivity of the PS nanocomposites with increasing concentration of nanowires. Polymer nanocomposites with low concentrations of functionalized nanowires showed lower complex viscosities than pure PS; this was attributed to a plasticizing effect introduced by the alkanethiols. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2064–2078, 2008     

Fabrication of monodisperse luminescent nanoparticles with core/shell poly(styrene/thiophene) structure

Luminescent poly(styrene/thiophene) (PSt/PT) core/shell nanoparticles were prepared by oxidative polymerization in the presence of PSt seed particles. PSt seed particles with uniform size distribution were prepared with an anionic surfactant by an emulsion polymerization process, and were used as a template to prepare monodispersive PT‐coated nanoparticles. A luminescent Polythiophene (PT) layer was formed on the surface of PSt nanoparticles by oxidation polymerization with iron chloride (FeCl₃) and hydrogen peroxide (H₂O₂). The mechanism of core/shell formation was found to be the interface‐dominant polymerization induced by the electrostatic attraction between the sulfonate group of anionic surfactant and Fe³⁺ ions after the diffusion of thiophene monomer to the PSt nanoparticles. Field‐emission scanning electron microscopy and transmission electron microscopy (TEM) proved the core/shell structure, which provided key evidence that PT was incorporated onto the surface of PSt nanoparticles. In addition, the effect of the PT shell thickness on photoluminescent (PL) intensity was investigated by changing the shell thickness of PSt/PT nanoparticles. We observed that the PL intensity increased up to about 30 nm of PT shell thickness, and then decreased due to self‐absorption. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5968–5975, 2008     

Preparation of nanocomposites by reversible addition‐fragmentation chain transfer polymerization from the surface of quantum dots in miniemulsion

Herein, we report the synthesis of quantum dots (QDs)/polymer nanocomposites by reversible addition‐fragmentation chain transfer (RAFT) polymerization in miniemulsions using a grafting from approach. First, the surfaces of CdS and CdSe QDs were functionalized using a chain transfer agent, a trisalkylphosphine oxide incorporating 4‐cyano‐4‐(thiobenzoylsulfanyl)pentanoic acid moieties. Using a free radical initiator (AIBN) to activate the RAFT process, a polystyrene (PS) block was grafted from the surface of the QDs. Quantum confinement effects were identified for the nanocomposite obtained, so attesting to the integrity of the QDs after the polymerization. Free PS chains were also present in the final nanocomposite, indicating that the RAFT polymerization from the surface of the QDs was accompanied by conventional free radical polymerization. After isolating the nanocomposite particles, a second poly(n‐butyl acrylate) block was tentatively grown from the initial PS block. The first results indicated a successful polymerization of the second polymer and show the potential of the current strategy to prepare block copolymers from the surface of the RAFT‐modified QDs. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5367–5377, 2009