Nonisothermal crystallization kinetics of in situ nylon 6/graphene composites by differential scanning calorimetry

The nonisothermal crystallization kinetics was investigated by differential scanning calorimetry for the nylon 6/graphene composites prepared by in situ polymerization. The Avrami theory modified by Jeziorny, Ozawa equation, and Mo equation was used to describe the nonisothermal crystallization kinetics. The analysis based on the Avrami theory modified by Jeziorny shows that, at lower cooling rates (at 5, 10, and 20 K/min), the nylon 6/graphene composites have lower crystallization rate than pure nylon 6. However, at higher cooling rates (at 40 K/min), the nylon 6/graphene composites have higher crystallization rate than pure nylon 6. The values of Avrami exponent m and the cooling crystallization function F(T) from Ozawa plots indicate that the mode of the nucleation and growth at initial stage of the nonisothermal crystallization may be as follows: two‐dimensional (2D), then one‐dimensional (1D) for all samples at 5–10 °C/min; three‐dimensional (3D) or complicated than 3D, then 2D and 1D at 10–20 and 20–40 °C/min. The good linearity of the Mo plots indicated that the combined approach could successfully describe the crystallization processes of the nylon 6 and nylon 6/graphene composites. The activation energies (ΔE) of the nylon 6/graphene composites, determined by Kissinger method, were lower than those of pure nylon 6. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1381–1388, 2011     

Influences of a liquid crystalline polymer,vectra A950, on crystallization kinetics and thermal stability of poly(trimethylene terephthalate)

The non-isothermal crystallization behavior of poly(trimethylene terephthalate) (PTT) and its blends with a liquid crystalline polymer, namely Vectra A950 (VA), was studied by differential scanning calorimetry. The values of the half-time of crystallization, t _0.5 and the parameter F(T) in the combined Avrami and Ozawa equation indicated that VA can enhance the PTT crystallization rate by acting as a nucleating agent. The crystallization activation energy of the PTT phase increased with increasing VA content. The blends were immiscible, as can be inferred from their morphology. Thermogravimetric analysis of the blends revealed improved thermal stability by the incorporation of VA.     

Isothermal and nonisothermal crystallization kinetics of irradiated nylon 1212

The crystallization behavior of nylon 1212, irradiated at ⁶⁰Co γ‐rays (50 kGy), was studied by a rheometer, polarized optical microscopy (POM), and differential scanning calorimeter (DSC). The results showed that irradiated nylon 1212 samples exhibited abnormal crystallization behavior during the crystallization process: The Avrami exponent n was calculated and was found to be in the range from 2.06–2.41 for isothermal crystallization, and from 2.67–4.91 for nonisothermal crystallization; the spherulite morphology also changed largely by polarized optical microscopy (POM); the crystallization activation energy ΔE for isothermal and nonisothermal crystallization process of irradiated nylon 1212 are determined to be 57.4 kJ/mol and 78.65 kJ/mol, respectively, which are lower than that of nonirradiated nylon 1212. At the same time, a new method by a combination of the Avrami and Ozawa equations was successfully applied to analyze the noncrystallization process of irradiated nylon 1212. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2326–2333, 2005     

Influence of <Emphasis Type="Italic">m</Emphasis>-isopropenyl-α,α-dimethylbenzyl isocyanate and styrene on non-isothermal crystallization behavior of polypropylene

Non-isothermal crystallization kinetics of polypropylene (PP), m-isopropenyl-α,α-dimethyl-benzyl isocyanate grafted PP (PP-g-m-TMI), and styrene(St), as comonomer, together with m-TMI grafted PP (PP-g-(St-m-TMI)) was investigated by using differential scanning calorimetry (DSC) under different cooling rates. The crystallization rates of all samples increased with increasing cooling rate. The relation of the half time of crystallization (t _1/2) of the three samples, t _{1/2(PP-g-(St-m-TMI))} < t _{1/2(PP-g-m-TMI)} < t _1/2(PP), implying the introduction of St could effectively improve the degree of grafting of m-TMI, resulting in crystallization temperature increased, and the crystallization rate was the fastest. Three methods, namely, the Avrami, the Ozawa, and the Mo, were used to describe the crystallization process of the three samples under non-isothermal conditions. The Avrami and Ozawa neglected the secondary crystallization that follows primary crystallization. The Mo method can successfully describe the overall non-isothermal crystallization process of all the samples. It has been found that the F(T)_{(PP-g-(St-m-TMI))} < F(T)_(PP-g-m-TMI) < F(T)_(PP), also meaning that the crystallization rate of PP-g-(St-m-TMI) and PP-g-m-TMI were faster than that of PP. The activation energy (ΔE) for non-isothermal crystallization of all samples was determined by using the Kissinger method. The result showed that the lower value of ΔE for crystallization obtained for PP-g-m -TMI and PP-g-(St-m-TMI) confirmed the nucleating effect of St and m-TMI on crystallization of PP.     

A query on crystallization temperature‐dependent cooling function under nonisothermal condition

The cooling function (κ) in Ozawa model was investigated through theoretic analysis and experimental method. Different from the fact accepted by researchers over past decades that κ(T) depends only on the crystallization temperature (T) and consequently the parameters for nonisothermal crystallization kinetics could be obtained by plotting ln[? ln(1 ? X(T))] versus ln λ at a given T, we found that κ at a given T was also dependent on onset temperature (T₀) of crystallization process. Because T₀ varies with cooling rate (λ) in nonisothermal crystallization, we conclude that κ is a binary function of T and λ, which was validated by our kinetic data from differential scanning calorimetry measurement in a wide λ range from 1 to 80 °C/min. It is suggested that the conventional method for calculating kinetic parameters based on Ozawa model, by plotting ln[? ln(1 ? X(T))] versus ln λ, might not be exact for nonisothermal crystallization. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44:795–800, 2006     

Multiple melting behavior of poly(butylene succinate). II. Thermal analysis of isothermal crystallization and melting process

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights (MWs) of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were isothermally crystallized at various crystallization temperatures (T_c) ranging from 70 to 97.5 °C. The T_c dependence of crystallization half‐time (τ) was obtained. DSC melting curves for the isothermally crystallized samples were obtained at a heating rate of 10 K min⁻¹. Three endothermic peaks, an annealing peak, a low‐temperature peak L, and a high‐temperature peak H, and an exothermic peak located between peaks L and H clearly appeared in the DSC curve. In addition, an endothermic small peak S appeared at a lower temperature of peak H. Peak L increased with increasing T_c, whereas peak H decreased. The T_c dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of T_c. T_m(L), T_re, and ΔH increased almost linearly with T_c, whereas T_m(H) was almost constant. The maximum rate of recrystallization occurred immediately after the melting. The mechanism of the multiple melting behavior is explained by the melt‐recrystallization model. The high MW samples showed similar T_c dependence of τ, and τ for the lowest MW sample was longer than that for the others. Peak L increased with MW, whereas peak H decreased. In spite of the difference of MW, T_m(L), T_m(H), and T_re almost coincided with each other at the same T_c. The ΔH values, that is crystallinity, for the highest MW sample were smaller than those for the other samples at the same T_c. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2039–2047, 2005     

Crystallization kinetics and melting behavior of metallocene short‐chain branched polyethylene fractions

Metallocene polyethylene (mPE) fractions are recognized as being more homogeneous with respect to short‐chain branch (SCB) distribution as compared with unfractionated mPEs. Differential scanning calorimetry and polarized optical microscopy (POM) were used to study the influences of SCB content on the crystallization kinetics, melting behavior, and crystal morphology of four butyl‐branched mPE fractions. The parent mPE of the studied fractions was also investigated for comparative purposes. mPE fractions showed a much simpler crystallization behavior as compared with their parent mPE during the cooling experiments. The Ozawa equation was successfully used to analyze the nonisothermal crystallization kinetics of the fractions. The Ozawa exponent n decreased from about 3.5 to 2 as the temperature declined for each fraction, indicating the crystal‐growth geometry changed from three‐dimensional to two‐dimensional. For isothermal crystallization, the fraction with a lesser SCB content exhibited a higher crystallization temperature (T_c) window. The results from the Avrami equation analysis showed the exponent n values were around 3 (with minor variation), which implied that the crystal‐growth geometry is pseudo‐three‐dimensional. Both of the activation energies for nonisothermal and isothermal crystallization were determined for each fraction with Kissinger and Arrhenius‐type equations, respectively. Double melting peaks were observed for both nonisothermally or isothermally crystallized specimens. The high‐melting peak was confirmed induced via the annealing effect during heating scans. The Hoffman–Weeks plot was inapplicable in obtaining the equilibrium melting temperature (T_m°) for each fraction. The relationship between T_c and T_m for the fractions is approximately T_m = T_c (°C) + 8.3. The POM results indicated that the crystals of parent or fractions formed under cooling conditions did not exhibit the typical spherulitic morphology as a result of the high SCB content. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 325–337, 2002     

Crystallization Kinetics of Polypropylene and Poly (butyl methacrylate-co-hydroxyethyl methacrylate) Blend

The crystallization kinetics of polypropylene and poly (butyl methacrylate-co-hydroxyethyl methacrylate) blend was investigated with differential scanning calorimetry. The isothermal crystallization analysis based on the Avrami theory indicated a heterogeneous nucleating effect from the copolymer. A systematic study of the nonisothermal crystallization kinetics was undertaken using the Avrami equation and its later modifications by Ozawa, Mo, and Zhang. The results demonstrated that the linear relationship failed in the different cooling rates because the Avrami method did not take into account that the crystallization temperature was lowered continuously. The Ozawa and Mo methods could be successful in describing the overall nonisothermal process of polypropylene and the blend. In addition, the nonisothermal crystallization energy values were estimated by the Kissinger and Freidman models. There are two mutually opposite effects on the crystallization behavior of the blend: nucleation ability and growth retardation.     

Effect of the Metal Phenylphosphonates on the Nonisothermal Crystallization and Performance of Isotactic Polypropylene

The use of metal phenylphosphonates as efficient nucleating agents (NAs) for isotactic polypropylene (iPP) is reported and a possible structural correlation to the nucleation efficiency is studied. First, three kinds of metal phenylphosphonates are synthesized via reflux method: Ca(C₆H₅PO₃)?2H₂O (CaPPA), Ca(C₆H₅PO₃H)₂ (CaPPA2), and Al(HO₃PC₆H₅)(O₃PC₆H₅)?H₂O (AlPPA2). Then, the nonisothermal crystallization behaviors, mechanical, and optical properties of iPP composites are investigated. Compared to CaPPA2 and AlPPA2, CaPPA exhibits more effective heterogeneous nucleation effect during iPP crystallization. Furthermore, the nucleation efficiency of CaPPA is similar to industrial standard NAs NA‐21 and NA‐11. With the addition of 0.1 wt % CaPPA, the crystallization temperature is enhanced and the parameter F(T) of Mo method is decreased appreciably. Moreover, the flexural modulus, impact strength, and haze values of iPP composites are improved remarkably by introducing CaPPA. The CH/π interaction between polymer and aromatic cleft of CaPPA is considered to facilitate the attachment of iPP chains and subsequent nucleation and crystallization, which is verified by the viscoelastic properties of pure iPP and composites. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 161–173     

Thermal behavior and crystallization kinetics of random poly(ethylene‐Co‐2,2‐Bis[4‐(ethylenoxy)‐1,4‐phenylene]propane terephthalate) copolyesters

The thermal behavior of poly(ethylene‐co‐2,2‐bis[4‐(ethylenoxy)‐1,4‐phenylene]propane terephthalate) (PET/BHEEBT) copolymers was investigated by thermogravimetric analysis and differential scanning calorimetry. A good thermal stability was found for all the samples. The thermal analysis carried out using DSC technique showed that the T_m of the copolymers decreased with increasing BHEEBT unit content, differently from T_g, which on the contrary increased. Wide‐angle X‐ray diffraction measurements permitted identifying the kind of crystalline structure of PET in all the semicrystalline samples. The multiple endotherms similar to PET were also evidenced in the PET/BHEEBT samples, due to melting and recrystallization processes. By applying the Hoffman–Weeks' method, the T_m° of PET and its copolymers was derived. The isothermal crystallization kinetics was analyzed according to Avrami's treatment and values of the exponent n close to 3 were obtained, independently of T_c and composition. Moreover, the introduction of BHEEBT units was found to decrease PET crystallization rate. Lastly, the presence of a crystal‐amorphous interphase was evidenced. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1441–1454, 2005     

Isothermal and nonisothermal crystallization kinetics of nylon‐46

Isothermal and nonisothermal crystallization kinetics of nylon‐46 were investigated with differential scanning calorimetry. The equilibrium melting enthalpy and the equilibrium melting temperature of nylon‐46 were determined to be 155.58 J/g and 307.10 °C, respectively. The isothermal crystallization process was described by the Avrami equation. The lateral surface free energy and the end surface free energy of nylon‐46 were calculated to be 8.28 and 138.54 erg/cm², respectively. The work of chain folding was determined to be 7.12 kcal/mol. The activation energies were determined to be 568.25 and 337.80 kJ/mol for isothermal and nonisothermal crystallization, respectively. A convenient method was applied to describe the nonisothermal crystallization kinetics of nylon‐46 by a combination of the Avrami and Ozawa equations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1784–1793, 2002     

Nonisothermal crystallization behavior of poly(m‐xylene adipamide)/montmorillonite nanocomposites

This article reports the nonisothermal crystallization behavior of MXD6 and its clay nanocomposite system (MXD6/MMT) using differential scanning calorimetry (DSC). The DSC experimental data were analyzed by theoretical modeling of the crystallization kinetics using the Avrami, Ozawa, Jeziorny, and the combined Avrami–Ozawa semiempirical models. It has been determined that these models adequately described the crystallization behavior of the MXD6 nanocomposite at cooling rates below 20 °C/min, but there was a deviation from linear dependence at higher cooling rates. This was attributed to changes of both the free energy and the cooling crystallization function K(T) over the entire crystallization process, as well as possible relaxation effects leading to structural rearrangements. In addition, the activation energy determined using the differential isoconversional method of Friedman was also found to vary, indicating changes in both the free energy and crystallization mechanism. Despite the lack of a reliable theoretical model, the heterogeneous nucleating activity of the MMT nanoparticles was demonstrated and quantified using Dobreva's method (? = 0.71), and the crystallization rate for the nanocomposite system was found to be greater than pure MXD6 by up to 79% at 40 °C/min. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1300–1312, 2009     

MELTING CRYSTALLIZATION BEHAVIOR OF NYLON 66

Analysis of isothermal and nonisothermal crystallization kinetics of nylon 66 was carried out using differentialscanning calorimetry (DSC). The commonly used Avrami equation and that modified by Jeziorny were used, respectively, tofit the primary stage of isothermal and nonisothermal crystallizations of nylon 66, In the isothermal crystallization process,mechanisms of spherulitic nucleation and growth were discussed. The lateral and folding surface free energies determinedfrom the Lauritzen-Hoffman treatment are σ= 9.77 erg/cm~2 and σ_e= 155.48 erg/cm~2, respectively; and the work of chainfolding is q = 33.14 kJ/mol. The nonisothermal crystallization kinetics of nylon 66 was analyzed by using the Mo methodcombined with the Avrami and Ozawa equations. The average Avrami exponent n was determined to be 3.45, Theactivation energies (ΔE) were determined to be -485.45 kJ/mol and -331.27 kJ/mol, respectively, for the isothermal andnonisothermal crystallization processes by the Arrhenius and the Kissinger methods.     

Crystallization behavior and morphology of poly(propylene terephthalate) copolymers containing neopenthyl glycol moieties

The melting behavior and the crystallization kinetics of random poly(propylene/neopenthyl terephthalate) copolymers (PPT‐PNT) were investigated by means of differential scanning calorimetry and hot‐stage optical microscopy. Multiple endotherms were evidenced in the PPT‐PNT samples, due to melting and recrystallization processes, similarly to PPT. By applying the Hoffman‐Weeks' method, the T_m° of the copolymers was derived. Baur's equation described well the T_m‐composition data. The isothermal crystallization kinetics was analyzed according to the Avrami's treatment. The introduction of NT units decreased the crystallization rate in comparison to pure PPT. Values of the Avrami's exponent close to three were obtained in all cases, regardless of T_c, in agreement with a crystallization process originating from predeterminated nuclei and characterized by three dimensional spherulitic growth. As a matter of fact, space‐filling spherulites were observed by optical microscopy at all T_cs. Banded spherulites were found for PPT‐PNT5 and PPT‐PNT10, the band spacing being affected by both T_c and composition. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 818–830, 2008     

Isotope Effects on the Crystallization Kinetics of Selectively Deuterated Poly(ε‐Caprolactone)

Deuterium labeling of semi‐crystalline polymers can dramatically affect their crystallization behaviors. However, the influence of different labeled positions in a partially deuterated polymer on its crystallization is still far from understood. Here, we synthesized a series of selectively deuterated poly(ε‐caprolactones) (PCLs) through ring‐opening polymerization of ε‐caprolactone with controlled deuteration sites, including fully protiated (D0), fully deuterated (D10), tetra deuteration at the 3‐ and 7‐ caprolactone ring positions (D4) and hexa deuteration at the 4‐, 5‐, and 6‐ caprolactone ring positions (D6). All the PCLs showed a similar lamellar structure and parameters. Differential scanning calorimetry (DSC) analysis revealed that the equilibrium melting temperature $T_m^0$, melting temperature T_m , crystallization temperature T_c , and crystallization kinetics changed systemically with the deuterium content except for D4, which indicates that the presence of ? CD₂? moieties on either side of ester group in the polymer chain combined with isotopic inhomogeneity could influence the chain packing. The nonmonotonic trend of T_m as a function of deuterium content could be attributed to the difference in a hydrogen‐bond like intermolecular interaction between different PCLs. Partially deuterated PCLs (D4 and D6) showed an Avrami index near 2. After analyzing the parameters at the same supercooling temperature ΔT_c , the existence of two crystallization regimes of PCLs were detected. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 771–779     

Nonisothermal cold crystallization behavior and kinetics of polylactide/clay nanocomposites

The nonisothermal cold crystallization behavior of intercalated polylactide (PLA)/clay nanocomposites (PLACNs) was studied using differential scanning calorimetry, polarized optical microscope, X‐ray diffractometer, dynamic mechanical thermal analysis, and Fourier transform infrared spectrometer. The results show that both the cold crystallization temperature (T_cc) and melting point (T_m) of PLA matrix decreases monotonously with increasing of clay loadings, accompanied by the decreasing degree of crystallinity (X_c%) at the low heating rates (≤5 °C/min). However, the X_c% of PLACNs presents a remarkable increase at the high heating rate of 10 °C/min in contrast to that of neat PLA. The crystallization kinetics was then analyzed by the Avrami, Jezioney, Ozawa, Mo, Kissinger and Lauritzen–Hoffman kinetic models. It can be concluded that at the low heating rate, the cold crystallization of both the neat PLA and nanocomposites proceeds by regime III kinetics. The nucleation effect of clay promote the crystallization to some extent, while the impeding effect of clay results in the decrease of crystallization rate with increasing of clay loadings. At the high heating rate of 10 °C/min, crystallization proceeds mainly by regime II kinetics. Thus, the formation of much more incomplete crystals in the PLACNs with high clay loadings due to the dominant multiple nucleations mechanism in regime II, may have primary contribution to the lower crystallization kinetics, also as a result to the higher degree of crystallinity and lower melting point in contrast to that of neat PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1100–1113, 2007     

一种典型半结晶型聚酰亚胺的非等温结晶动力学

使用3,3 ′,4,4′-联苯四酸二酐( s-BPDA),1,3,-双(4-氨基苯氧基)苯(TPER)和苯酐(PA)反应合成了一种半结晶型聚酰亚胺.根据DSC记录的不同速率下降温所得到的结晶放热曲线,分别采用Jeziorny、Ozawa及奠志深提出的方法对其非等温结晶行为进行了研究.发现由Jeziorny方法分析得到的...     

Preparation and crystallization behaviour of PP/PP-g-MAH/Org-MMT nanocomposite

The melt-direct intercalation method was employed to prepare polypropylene (PP)/maleic anhydride grafted polypropylene (PP-g-MAH)/organic-montmorillonite (Org-MMT), X-ray diffractometer was used to investigate the intercalation effect and crystallite size in composites and TEM micrograph to observe the dispersion of Org-MMT interlayers in polypropylene. The results showed that by introducing maleated polypropylene in PP/Org-MMT composite, macromolecule segments had intercalated into interlayer space of Org-MMT. As a result, Org-MMT interlayers were dispersed evenly in polypropylene and PP/PP-g-MAH/Org-MMT nanocomposite was synthesized. The crystallite size of nanocomposite perpendicular to the crystalline plane such as (0 4 0), (1 3 0), (1 1 1), (0 4 1) is smaller than that of pristine PP, which indicated that the crystallite size of PP in nanocomposite can be diminished by adding PP-g-MAH and Org-MMT in PP. Moreover, the nonisothermal crystallization kinetics of PP and PP/PP-g-MAH/Org-MMT nanocomposite was investigated by differential scanning calorimetry (DSC) with various cooling rates. The Avrami analysis modified by Jeziorny, Ozawa method and a method developed by Liu were employed to describe the nonisothermal crystallization process of these samples. The difference in the exponent n between PP and nanocomposite, indicated that nonisothermal kinetic crystallization corresponded to tridimensional growth with heterogeneous nucleation. The values of half-time, Z_c, F(T) and K(T) showed that the crystallization rate of composites was faster than that of PP at a given cooling rate.     

Multiple melting behavior of poly(butylene succinate). I. Thermal analysis of melt‐crystallized samples

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were cooled from the melt (150 °C) at various cooling rates (CRs) ranging from 0.2 to 50 K min^?1. The peak crystallization temperature (T_c) of the DSC curve in the cooling process decreased almost linearly with the logarithm of the CR. DSC melting curves for the melt‐crystallized samples were obtained at 10 K min^?1. Double endothermic peaks, a high‐temperature peak H and a low‐temperature peak L, and an exothermic peak located between them appeared. Peak L decreased with increasing CR, whereas peak H increased. An endothermic shoulder peak appeared at the lower temperature of peak H. The CR dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of log(CR). T_m(L), T_re, and ΔH decreased almost linearly with log(CR), whereas T_m(H) was almost constant. Peak H decreased with the molecular weight, whereas peak L increased. It was suggested that the rate of the recrystallization decreased with the molecular weight. T_m(L), T_m(H), T_re, and T_c for the lowest molecular weight sample were lower than those for the others. In contrast, ΔH for the highest molecular weight sample was lower than that for the others. If the molecular weight dependence of the melting temperature for PBSu is similar to that for polyethylene, the results for the molecular weight dependence of PBSu can be explained. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2411–2420, 2002     

Effects of β‐nucleating agent and crystallization conditions on the crystallization behavior and polymorphic composition of isotactic polypropylene/multi‐walled carbon nanotubes composites

In this study, the effects of crystallization conditions (cooling rate and end temperature of cooling) on crystallization behavior and polymorphic composition of isotactic polypropylene/multi‐walled carbon nanotubes (iPP/MWCNTs) composites nucleated with different concentrations of β‐nucleating agent (tradename TMB‐5) were investigated by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and scanning electronic microscopy (SEM). The results of DSC, WAXD and SEM revealed that the addition of MWCNTs and TMB‐5 evidently elevates crystallization temperatures and significantly decreases the crystal sizes of iPP. Because of the competition between α‐nucleation (provided by MWCNTs) and β‐nucleation (induced by TMB‐5), the β‐phase crystallization takes place only when 0.15 wt% and higher concentration of TMB‐5 is added. Non‐isothermal crystallization kinetics study showed that the crystallization activation energy ΔE of β‐nucleated iPP/MWCNTs composites is obviously higher than that of pure iPP, which slightly increases with the increase of TMB‐5 concentration, accompanying with the transition of its polymorphic crystallization behavior. The results of non‐isothermal crystallization and melting behavior suggested that the cooling rate and end temperature of cooling (T_end) are important factors in determining the proportion and thermal stability of β‐phase: Lower cooling rate favors the formation of less amount of β‐phase with higher thermal stability, while higher cooling rate encourages the formation of higher proportion of β‐phase with lower thermal stability. The T_end = 100°C can eliminate the β–α recrystallization during the subsequent heating and therefore enhance the thermal stability of the β‐phase. By properly selecting TMB‐5 concentration, cooling rate and T_end, high β‐phase proportion of 88.9% of the sample was obtained. Copyright © 2014 John Wiley & Sons, Ltd.