Syntheses of 12‐arm star polymers and star diblock copolymers by nitroxide‐mediated radical polymerization using dendritic dodecafunctional macroinitiators

Dendritic multifunctional macroinitiators having 12 TEMPO‐based alkoxyamines were prepared by the reaction of a benzyl alcohol having 4 TEMPO‐based alkoxyamines with 1,3,5‐tris[(4‐chlorocarbonyl)phenyl]benzene and 1,3,5‐tris(4‐isocyanatophenyl)benzene. Using the dodecafunctional macroinitiators, TEMPO‐mediated radical polymerizations of styrene (St) were carried out at 120 °C, and 12‐arm star polymers ( star‐12 ) with narrow polydispersities of M_w/M_n = 1.06–1.26 were obtained. To evaluate the livingness for the TEMPO‐mediated radical polymerizations of St, hydrolysis of the ester bonds of the 12‐arm star polymers and subsequent SEC measurements were carried out. Furthermore, using star‐12 as the macroinitiator, TEMPO‐mediated radical polymerization of 4‐vinylpyridine (4‐VP) was carried out, and well‐defined poly(St)‐b‐poly(4‐VP) 12‐arm star diblock copolymers with M_w/M_n = 1.18–1.19 were obtained. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3689–3700, 2005     

Synthesis of well‐defined cyclodextrin‐core star polymers

The synthesis of 21‐arm methyl methacrylate (MMA) and styrene star polymers is reported. The copper (I)‐mediated living radical polymerization of MMA was carried out with a cyclodextrin‐core‐based initiator with 21 independent discrete initiation sites: heptakis[2,3,6‐tri‐O‐(2‐bromo‐2‐methylpropionyl]‐β‐cyclodextrin. Living polymerization occurred, providing well‐defined 21‐arm star polymers with predicted molecular weights calculated from the initiator concentration and the consumed monomer as well as low polydispersities [e.g., poly(methyl methacrylate) (PMMA), number‐average molecular weight (M_n) = 55,700, polydispersity index (PDI) = 1.07; M_n = 118,000, PDI = 1.06; polystyrene, M_n = 37,100, PDI = 1.15]. Functional methacrylate monomers containing poly(ethylene glycol), a glucose residue, and a tert‐amine group in the side chain were also polymerized in a similar fashion, leading to hydrophilic star polymers, again with good control over the molecular weight and polydispersity (M_n = 15,000, PDI = 1.03; M_n = 36,500, PDI = 1.14; and M_n = 139,000, PDI = 1.09, respectively). When styrene was used as the monomer, it was difficult to obtain well‐defined polystyrene stars at high molecular weights. This was due to the increased occurrence of side reactions such as star–star coupling and thermal (spontaneous) polymerization; however, low‐polydispersity polymers were achieved at relatively low conversions. Furthermore, a star block copolymer consisting of PMMA and poly(butyl methacrylate) was successfully synthesized with a star PMMA as a macroinitiator (M_n = 104,000, PDI = 1.05). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2206–2214, 2001     

Three‐arm star block copolymers of ε‐caprolactone and acrylic acid: Synthesis and micellization behavior

A series of well‐defined three‐arm star poly(ε‐caprolactone)‐b‐poly(acrylic acid) copolymers having different block lengths were synthesized via the combination of ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP). First, three‐arm star poly(ε‐caprolactone) (PCL) (M_n = 2490–7830 g mol^?1; M_w/M_n = 1.19–1.24) were synthesized via ROP of ε‐caprolactone (ε‐CL) using tris(2‐hydroxyethyl)cynuric acid as three‐arm initiator and stannous octoate (Sn(Oct)₂) as a catalyst. Subsequently, the three‐arm macroinitiator transformed from such PCL in high conversion initiated ATRPs of tert‐butyl acrylate (^tBuA) to construct three‐arm star PCL‐b‐P^tBuA copolymers (M_n = 10,900–19,570 g mol^?1; M_w/M_n = 1.14–1.23). Finally, the three‐arm star PCL‐b‐PAA copolymer was obtained via the hydrolysis of the PtBuA segment in three‐arm star PCL‐b‐P^tBuA copolymers. The chain structures of all the polymers were characterized by gel permeation chromatography, proton nuclear magnetic resonance (¹H NMR), and Fourier transform infrared spectroscopy. The aggregates of three‐arm star PCL‐b‐PAA copolymer were studied by the determination of critical micelles concentration and transmission electron microscope. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Well‐defined polyoxazoline‐based alkoxyamines as efficient macroinitiators in nitroxide‐mediated radical polymerization of styrene

The synthesis of two well‐defined 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐nitroxide‐terminated poly(2‐methyl‐2‐oxazoline) with narrow dispersity (M_w/M_n = 1.1) has been achieved for the first time. The insertion of the alkoxyamine end groups at one or both ends of poly(2‐methyl‐2‐oxazoline) (PMEOX) chains has been successfully done using a method based on “terminating reagent method.” These macroinitiators have molecular weights ranging from 6.3 × 10³ to 9.4 × 10³ g mol^?1. In contrast, attempt to introduce the alkoxyamine group at one end of PMEOX chain through the “initiator method” has furnished a mixture of alkoxyamine‐graft polyoxazolines because of rearrangement of alkoxyamine occurring during the synthesis of PMEOX. The macroinitiators obtained by terminating reagent method have been used successfully for polymerization of styrene by nitroxide‐mediated radical polymerization (NMP), which exhibited all the expected features of a controlled system. The control of NMP has been proved by a good agreement between theoretical and experimental molecular weights and by narrow dispersity (M_w/M_n < 1.2). Different types of well‐defined multiblock copolymers have been prepared: diblock copolymers poly[(2‐methyl‐2‐oxazoline)‐b‐(styrene)] (PMEOX‐b‐PS) and, for the first time, triblock copolymers poly[(styrene)‐b‐(2‐methyl‐2‐oxazoline)‐b‐(styrene)] (PS‐b‐PMEOX‐b‐PS). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Synthesis of miktoarm star amphiphilic block copolymers via combination of NMRP and ATRP and investigation on self‐assembly behaviors

The novel trifunctional initiator, 1‐(4‐methyleneoxy‐2,2,6,6‐tetramethylpip‐eridinoxyl)‐3,5‐bi(bromomethyl)‐2,4,6‐trimethylbenzene (TEMPO‐2Br), was successfully synthesized and used to prepare the miktoarm star amphiphilic poly(styrene)‐(poly(N‐isopropylacrylamide))₂ (PS(PNIPAAM)₂) via combination of atom transfer radical polymerization (ATRP) and nitroxide‐mediated radical polymerization (NMRP) techniques. Furthermore, the star amphiphilic block copolymer, poly (styrene)‐(poly(N‐isopropylacrylamide‐b‐4‐vinylpyridine))₂ (PS(PNIPAAM‐b‐P4VP)₂), was also prepared using PS(PNIPAAM)₂ as the macroinitiator and 4‐vinylpyridine as the second monomer by ATRP method. The obtained polymers were well‐defined with narrow molecular weight distributions (M_w/M_n ≤ 1.29). Meanwhile, the self‐assembly behaviors of the miktoarm amphiphilic block copolymers, PS(PNIPAAM)₂ and PS(PNIPAAM‐b‐P4VP)₂, were also investigated. Interestingly, the aggregate morphology changed from sphere‐shaped micelles (4.7 < pH < 3.0) to a mixture of spheres and rods (1.0 < pH < 3.0), and rod‐shaped nanorods formed when pH value was below 1.0. The LCST of PS(PNIPAAM)₂ (pH = 7) was about 31 °C and the LCST of PS(PNIPAAM‐b‐P4VP)₂ was about 35 °C (pH = 3). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6304–6315, 2009     

Synthesis of bio‐based poly(N‐phenylitaconimide) by atom transfer radical polymerization

Poly(N‐phenylitaconimide) (polyPhII) was prepared using initiators for continuous activator regeneration atom transfer radical polymerization of PhII using FeBr₃ complexes as catalysts. Conversion reached 69% in 24 h, yielding polyPhII with a number average molecular weight M_n = 11,900 and a molecular weight distribution M_w/M_n = 1.52. Copolymerizations of PhII with styrene at various molar ratios were performed providing a range of polyPhII‐copolySt polymers. When the copolymerization was carried out with higher [St]₀ > [PhII]₀ ratio, a one‐pot synthesis of poly(St‐alt‐PhII)‐b‐polySt was achieved. The thermal properties of the obtained copolymers were studied by differential scanning calorimetry. PolyPhII prepared by ATRP showed high glass transition temperature (T_g) of 216 °C and the poly(St‐alt‐PhII)‐b‐polySt exhibited two T_gs, at 162 and 104 °C, corresponding to a poly(St‐alt‐PhII) and polySt segments, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 822–827     

Synthesis of refractive star‐shaped polysulfide by anionic polymerization of phenoxy propylene sulfide using an initiating system consisting of trifunctional thiol derived from five‐membered cyclic dithiocarbonate and amine

Star‐shaped poly(phenoxy propylene sulfide) [poly (PPS)] were synthesized by anionic polymerization using a trifunctional initiator ( I ₁) derived from a trifunctional five‐membered cyclic dithiocarbonate and benzyl amine. Conditions for the anionic polymerization of PPS were optimized to obtain polymers with desired M_ns and narrow M_w/M_ns. The best catalyst and solvent were DBU and DMF, respectively. The star‐shaped structure of the resulting star poly(PPS) was supported by SEC analysis. The refractive indexes (n_D) of the star poly (PPS) were relatively high (>1.64). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 525–531, 2010     

Study of Phase Separation of Poly(N-isopropylacrylamide-co-styrene) Aqueous Solutions with Rayleigh Scattering Technique

A thermally sensitive copolymer, poly(N‐isopropylacrylamide‐co‐styrene) [P(NIPAM‐co‐St)] (M_n?9.5×10⁵ g/mol and M_w/M_n?1.51) was synthesized by soap‐free emulsion polymerization. The phase separation of the copolymer in water was investigated by Rayleigh scattering (RS) technique. The RS spectra revealed the transition of molecular conformation and the aggregation of molecular chains in the course of phase separation. The coil‐to‐globule and globule‐to‐coil transitions of P(NIPAM‐co‐St) chains were found in one heating‐and‐cooling cycle. By means of Avrami formula, apparent activation energy of phase separation of P(NIPAM‐co‐St) aqueous solutions was estimated. Moreover, a model was proposed to describe the phase separation process.     

Synthesis of well‐defined AB20‐type star polymers with cyclodextrin‐core by combination of NMP and ATRP

The synthesis of an AB₂₀‐type heteroarm star polymer consisting of a polystyrene arm and 20‐arms of poly(methyl methacrylate) or poly(tert‐butyl acrylate) was carried out using the combination of nitroxide‐mediated polymerization (NMP) and atom transfer radical polymerization (ATRP). The NMP of styrene was carried out using mono‐6‐[4‐(1′‐(2″,2″,6″,6″‐tetramethyl‐1″‐piperidinyloxy)‐ethyl)benzamido]‐β‐cyclodextrin peracetate ( 1 ) to afford end‐functionalized polystyrene with an acetylated β‐cyclodextrin (β‐CyD) unit (prepolymer 2 ) with a number‐average molecular weight (M_n) of 11700 and a polydispersity (M_w/M_n) of 1.17. After deacetylation of prepolymer 2 , the resulting polymer was reacted with 2‐bromoisobutyric anhydride to give end‐functionalized polystyrene with 20(2‐bromoisobutyrol)s β‐CyD, macroinitiator 4 . The copper (I)‐mediated ATRP of methyl methacrylate (MMA) and tert‐butyl acrylate (tBA) was carried out using macroinitiator 4 . The resulting polymers were isolated by SEC fractionation to produce AB₂₀‐type star polymers with a β‐CyD‐core, 5 . The well‐defined structure of 5 with weight‐average molecular weight (M_w)s of 13,500–65,300 and M_w/M_n's of 1.26–1.28 was demonstrated by SEC and light scattering measurements. The arm polymers were separated from 5 by destruction with 28 wt % sodium methoxide in order to analyze the details of their characteristic structure. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4271–4279, 2005     

Synthesis and characterization of 6‐ and 12‐arm star polymers by nitroxide‐mediated radical polymerization of St and MA from dendritic TIPNO‐based hexafunctional and dodecafunctional macroinitiators

Dendritic multifunctional macroinitiators having six and 12 TIPNO‐based alkoxyamines, TIPNO‐6 and TIPNO‐12 , were synthesized and used in the living radical polymerization of styrene (St), methyl acrylate (MA), N,N‐dimethylacrylamide (DMAAm), and isoprene (IP). The polymerizations of St initiated with TIPNO‐6 gave 6‐arm star polymers with narrow polydispersities of 1.14–1.18. In the polymerizations of MA initiated with TIPNO‐6 and TIPNO‐12 , the influences of added TIPNO on the polydispersity indexes (PDIs) of the resulting star polymers were first investigated, and this led to the successful formation of poly(MA) star polymers with narrow polydispersities (1.10–1.18). Moreover, the polymerizations of DMAAm and IP from TIPNO‐6 in the presence or absence of TIPNO were briefly investigated. The benzyl ether bonds of the poly(St) and poly(MA) star polymers were cleaved by treating with Me₃SiI or Pd/C, and the resulting arm's parts were analyzed with SEC. The PDIs of the resulting arm parts were low (1.19–1.23), and the M_ns agreed with the M_n,theor, indicating that the poly(St) and poly(MA) star polymers had well‐controlled arms. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4364–4376, 2007     

Synthesis of poly(dimethylsiloxane)‐containing diblock and triblock copolymers by the combination of anionic ring‐opening polymerization of hexamethylcyclotrisiloxane and nitroxide‐mediated radical polymerization of methyl acrylate,isoprene, and styrene

Poly(dimethylsiloxane)‐containing diblock and triblock copolymers were prepared by the combination of anionic ring‐opening polymerization (AROP) of hexamethylcyclotrisiloxane (D₃) and nitroxide‐mediated radical polymerization (NMRP) of methyl acrylate (MA), isoprene (IP), and styrene (St). The first step was the preparation of a TIPNO‐based alkoxyamine carrying a 4‐bromophenyl group. The alkoxyamine was then treated with Li powder in ether, and AROP of D₃ was carried out using the resulting lithiophenyl alkoxyamine at room temperature, giving functional poly(D₃) with M_w/M_n of 1.09–1.16. NMRPs of MA, St, and IP from the poly(D₃) at 120 °C gave poly(D₃‐b‐MA), poly(D₃‐b‐St), and poly(D₃‐b‐IP) diblock copolymers, and subsequent NMRPs of St from poly(D₃‐b‐MA) and poly(D₃‐b‐IP) at 120 °C gave poly(D₃‐b‐MA‐b‐St) and poly(D₃‐b‐IP‐b‐St) triblock copolymers. The poly(dimethylsiloxane)‐containing diblock and triblock copolymers were analyzed by ¹H NMR and size exclusion chromatography. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6153–6165, 2005     

Star‐shaped cyclopolymers: A new category of star polymer with rigid cyclized arms prepared by controlled cationic cyclopolymerization and subsequent microgel formation of divinyl ethers

The combination of living/controlled cationic cyclopolymerization and crosslinking polymerization of bifunctional vinyl ethers (divinyl ethers) was applied to the synthesis of core‐crosslinked star‐shaped polymers with rigid cyclized arms. Cyclopolymerization of 4,4‐bis(vinyloxymethyl)cyclohexene ( 1 ), a divinyl ether with a cyclohexene group, was investigated with the hydrogen chloride/zinc chloride (HCl/ZnCl₂) initiating system in toluene at 0 °C. The reaction proceeded quantitatively to give soluble poly( 1 )s in organic solvents. The content of the unreacted vinyl groups in the produced polymers was less than ～3 mol%, and therefore, the degree of cyclization of the polymers was determined to be ～97%. The number‐average molecular weight (M_n) of the polymers increased in direct proportion to monomer conversion and further increased on addition of a fresh monomer feed to the almost completely polymerized reaction mixture, indicating that living cyclopolymerization of 1 occurred. The chain linking reactions among the formed living cyclopolymers with 1,4‐bis(vinyloxy)cyclohexane ( 3 ) as a crosslinker in toluene at 0 °C produced core‐crosslinked star‐shaped cyclopoly( 1 )s [star‐poly( 1 )s] in high yield (100%). Dihydroxylation of the cyclohexene double bonds of star‐poly( 1 ) gave hydrophilic water‐soluble star‐shaped polymers with rigid arm structure [star‐poly( 1 )‐OH] with thermo‐responsive function in water. T_gs of star‐poly( 1 ) and star‐poly( 1 )‐OH were 135 °C and 216 °C, respectively; these values are very high as vinyl ether‐based star‐shaped polymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1094–1102     

Poly(styrene‐b‐isobutylene) multiarm star‐block copolymers

Multiarm star‐branched polymers based on poly(styrene‐b‐isobutylene) (PS‐PIB) block copolymer arms were synthesized under controlled/living cationic polymerization conditions using the 2‐chloro‐2‐propylbenzene (CCl)/TiCl₄/pyridine (Py) initiating system and divinylbenzene (DVB) as gel‐core‐forming comonomer. To optimize the timing of isobutylene (IB) addition to living PS⊕, the kinetics of styrene (St) polymerization at −80°C were measured in both 60 : 40 (v : v) methyl cyclohexane (MCHx) : MeCl and 60 : 40 hexane : MeCl cosolvents. For either cosolvent system, it was found that the polymerizations followed first‐order kinetics with respect to the monomer and the number of actively growing chains remained invariant. The rate of polymerization was slower in MCHx : MeCl (k_app = 2.5 × 10⁻³ s⁻¹) compared with hexane : MeCl (k_app = 5.6 × 10⁻³ s⁻¹) ([CCl]_o = [TiCl₄]/15 = 3.64 × 10⁻³M; [Py] = 4 × 10⁻³M; [St]_o = 0.35M). Intermolecular alkylation reactions were observed at [St]_o = 0.93M but could be suppressed by avoiding very high St conversion and by setting [St]_o ≤ 0.35M. For St polymerization, k_app = 1.1 × 10⁻³ s⁻¹ ([CCl]_o = [TiCl₄]/15 = 1.82 × 10⁻³M; [Py] = 4 × 10⁻³M; [St]_o = 0.35M); this was significantly higher than that observed for IB polymerization (k_app = 3.0 × 10⁻⁴ s⁻¹; [CCl]_o = [Py] = [TiCl₄]/15 = 1.86 × 10⁻³M; [IB]_o = 1.0M). Blocking efficiencies were higher in hexane : MeCl compared with MCHx : MeCl cosolvent system. Star formation was faster with PS‐PIB arms compared with PIB homopolymer arms under similar conditions. Using [DVB] = 5.6 × 10⁻²M = 10 times chain end concentration, 92% of PS‐PIB arms (M_n,PS = 2600 and M_n,PIB = 13,400 g/mol) were linked within 1 h at −80°C with negligible star–star coupling. It was difficult to achieve complete linking of all the arms prior to the onset of star–star coupling. Apparently, the presence of the St block allows the PS‐PIB block copolymer arms to be incorporated into growing star polymers by an additional mechanism, namely, electrophilic aromatic substitution (EAS), which leads to increased rates of star formation and greater tendency toward star–star coupling. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1629–1641, 1999     

Synthesis of miktoarm star and miktoarm star block copolymers via a combination of atom transfer radical polymerization and stable free‐radical polymerization

A trifunctional initiator, 2‐phenyl‐2‐[(2,2,6,6‐tetramethyl)‐1‐piperidinyloxy] ethyl 2,2‐bis[methyl(2‐bromopropionato)] propionate, was synthesized and used for the synthesis of miktoarm star AB₂ and miktoarm star block AB₂C₂ copolymers via a combination of stable free‐radical polymerization (SFRP) and atom transfer radical polymerization (ATRP) in a two‐step or three‐step reaction sequence, respectively. In the first step, a polystyrene (PSt) macroinitiator with dual ω‐bromo functionality was obtained by SFRP of styrene (St) in bulk at 125 °C. Next, this PSt precursor was used as a macroinitiator for ATRP of tert‐butyl acrylate (tBA) in the presence of Cu(I)Br and pentamethyldiethylenetriamine at 80 °C, affording miktoarm star (PSt)(PtBA)₂ [where PtBA is poly(tert‐butyl acrylate)]. In the third step, the obtained St(tBA)₂ macroinitiator with two terminal bromine groups was further polymerized with methyl methacrylate by ATRP, and this resulted in (PSt)(PtBA)₂(PMMA)₂‐type miktoarm star block copolymer [where PMMA is poly(methyl methacrylate)] with a controlled molecular weight and a moderate polydispersity (weight‐average molecular weight/number‐average molecular weight < 1.38). All polymers were characterized by gel permeation chromatography and ¹H NMR. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2542–2548, 2003     

Synthesis of well‐defined and end‐polymerizable star‐shaped polysulfides and their application to negative photoresist

Various star‐shaped poly(phenoxy propylene sulfide)s (PPSs) bearing curable end groups were synthesized by the functionalization of the propagating ends of star‐shaped poly(PPS) with various electrophilies. The functionalization with chloromethyl styrene proceeded quantitatively, and afforded polymers with M_n almost agreed with theoretical value and narrow M_w/M_n. The photocuring conditions were optimized, and the addition of 10 wt % of poly(ethylene glycol) diacrylate was effective to attain sufficient crosslinking. The photocuring reaction of the end‐functionalized poly(PPS) films cast on silicon wafers was conducted by UV irradiation. The cured poly (PPS)s became insoluble in THF, supporting the sufficient crosslinking. Developing of a cured polymer yielded a negative photoresist pattern. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Electroactive methacrylate‐based triblock copolymer elastomer for actuator application

A series of ABA triblock copolymers of methyl methacrylate (MMA) and dodecyl methacrylate (DMA) [poly(MMA‐b‐DMA‐b‐MMA)] (PMDM) were synthesized by Ru‐based sequential living radical polymerization. For this, DMA was first polymerized from a difunctional initiator, ethane‐1,2‐diyl bis(2‐chloro‐2‐phenylacetate) with combination of RuCl₂(PPh₃)₃ catalyst and nBu₃N additive in toluene at 80 °C. As the conversion of DMA reached over about 90%, MMA was directly added into the reaction solution to give PMDM with controlled molecular weight (M_w/M_n ≤ 1.2). These triblock copolymers showed well‐organized morphologies such as body centered cubic, hexagonal cylinder, and lamella structures both in bulk and in thin film by self‐assembly phenomenon with different poly(methyl methacrylate) (PMMA) weight fractions. Obtained PMDMs with 20–40 wt % of the PMMA segments showed excellent electroactive actuation behaviors at relatively low voltages, which was much superior compared to conventional styrene‐ethylene‐butylene‐styrene triblock copolymer systems due to its higher polarity derived from the methacrylate backbone and lower modulus. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Polymethylene‐block‐polystyrene copolymers: A new synthetic approach using a combination of polyhomologation and reversible addition‐fragmentation chain‐transfer polymerization and their microfibers and microspheres fabricated through electrospinning process

Well‐defined polymethylene‐block‐polystyrene (PM‐b‐PS) diblock copolymers were synthesized via a combination of polyhomologation of ylides and reversible addition‐fragmentation chain‐transfer (RAFT) polymerization of styrene. Trithiocarbonate‐terminated polymethylenes (PM‐TTCB) (M_n = 1400 g mol^?1; M_w/M_n = 1.09 and M_n = 2100 g mol^?1; M_w/M_n = 1.20) were obtained via an esterification of S?1‐dodecyl‐S′‐(α,α′‐dimethyl‐α″‐acetate) trithiocarbonate with hydroxyl‐terminated polymethylene synthesized via polyhomologation of ylides followed by oxidation. Then, a series of PM‐b‐PS (M_n = 5500–34,000 g mol^?1; M_w/M_n = 1.12–1.25) diblock copolymers were obtained by RAFT polymerization of styrene using PM‐TTCB as a macromolecular chain‐transfer agent. The chain structures of all the polymers were characterized by proton nuclear magnetic resonance (¹H NMR), gel permeation chromatography, and Fourier transform infrared spectroscopy. The thiocarbonylthio end‐group of PM‐b‐PS was transformed into thiol group by aminolysis and confirmed by UV–vis spectroscopy. In addition, microfibers and microspheres of such diblock copolymers were fabricated by electrospinning process and observed by scanning electron microscopy (SEM). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2892–2899     

Formation of polymeric micelles with amino surfaces from amphiphilic AB‐type diblock copolymers composed of poly(glycolic acid lysine) segments and polylactide segments

Amphiphilic AB‐type diblock copolymers composed of hydrophobic poly(L ‐lactide) (PLA) segments and hydrophilic poly(glycolic acid lysine) [poly(Glc‐Lys)] segments with amino side‐chain groups self‐associated to form PLA‐based polymeric micelles with amino surfaces in an aqueous solution. The average diameter of the loose core–shell polymeric micelles for poly(Glc‐Lys) [number‐average molecular weight (M_n) = 1240]‐b‐PLA (M_n = 7000) obtained by a dimethyl sulfoxide/water dialysis method was estimated to be about 50 nm in water by dynamic light scattering measurements. The size and shape of the obtained polymeric micelles were further observed with transmission electron microscopy and atomic force microscopy. To investigate the possibility of applying the obtained PLA‐based polymeric micelles as bioabsorbable vehicles for hydrophobic drugs, we tested the entrapment of drugs in poly(Glc‐Lys) (M_n = 1240)‐b‐PLA (M_n = 7000) micelles and their release with doxorubicin as a hydrophobic drug. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1426–1432, 2002     

Well‐defined amphiphilic polymethylene‐b‐poly(acrylic acid) diblock copolymers: New synthetic strategy and their self‐assembly

Well‐defined amphiphilic polymethylene‐b‐poly (acrylicacid) diblock copolymers have been synthesized via a new strategy combining polyhomologation and atom transfer radical polymerization (ATRP). Hydroxyl‐terminated polymethylenes (PM‐OH) with different molecular weights and narrow molecular weight distribution are obtained through the polyhomologation of dimethylsulfoxonium methylides following quantitative oxidation via trimethylamine‐N‐oxide dihydrate. Subsequently, polymethylene‐based macroinitiators (PM‐MIs M_n = 1,300 g mol^?1 [M_w/M_n = 1.11] and M_n = 3,300 g mol^?1 [M_w/M_n = 1.04]) are synthesized by transformation of terminal hydroxyl group of PM‐OH to α‐haloester in ～100% conversion. ATRPs of tert‐butyl acrylate (t‐BuA) are then carried out using PM‐MIs as initiator to construct PM‐b‐P(t‐BuA) diblock copolymers with controllable molecular weight (M_n = 8,800–15,800 g mol^?1 M_w/M_n = 1.04–1.09) and different weight ratio of PM/P(t‐BuA) segment (1:1.7–1:11.2). The amphiphilic PM‐b‐PAA diblock copolymers are finally prepared by hydrolysis of PM‐b‐P(t‐BuA) copolymers and their self‐assembly behavior in water is preliminarily investigated via the determination of critical micelle concentrations, dynamic light scattering, and transmission electron microscope (TEM). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Glycoconjugated polymer: Synthesis and characterization of poly(vinyl saccharide)‐block‐polystyrene‐block‐poly(vinyl saccharide) as an amphiphilic ABA triblock copolymer

Styrene (St) was polymerized with α,α′‐bis(2′,2′,6′,6′‐tetramethyl‐1′‐piperidinyloxy)‐1,4‐diethylbenzene ( 1 ) as an initiator (bulk, [St]/] 1 ] = 570) at 120 °C for 5.0 h to obtain polystyrene having 2,2,6,6‐tetramethylpiperidiloxy moieties on both sides of the chain ends ( 2 ) with a number‐average molecular weight (M_n) of 14,300 and a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.14. 4‐Vinylbenzyl glucoside peracetate ( 3a ) was polymerized with 2 as a macromolecular initiator and dicumyl peroxide (DCP) as an accelerator in chlorobenzene at 120 °C. The polymerization with the [ 3a ]/[ 2 ]/[DCP] ratio of 30/1/1.2 for 5 h afforded a product in a yield of 73%; it was followed by purification with preparative size exclusion chromatography to provide the ABA triblock copolymer containing the pendant acetyl glucose on both sides of the chain ends ( 4a ; M_n = 21,000, M_w/M_n = 1.16). Similarly, the polymerization of 4‐vinylbenzyl maltohexaoside peracetate produced the ABA triblock copolymer containing the pendant acetyl maltohexaose on both side of the chain end ( 4b ; M_n = 31,800, M_w/M_n = 1.11). Polymers 4a and 4b were modified by deacetylation into amphiphilic ABA triblock copolymers containing the pendant glucose and maltohexaose as hydrophilic segment, 5a and 5b , respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3978–3985, 2006