The thermal degradation of poly(diethyl fumarate)

The kinetics and mechanism of the thermal degradation of poly(diethyl fumarate) (PDEF) were studied by thermogravimetry, as well as by analysis of the thermolysis volatiles and polymer residue. The characteristic mass loss temperatures were determined, as were the overall thermal degradation activation energies of three PDEF samples of varying molar mass. Ethylene and ethanol were present in the thermolysis volatiles at degradation temperatures below 300 °C, while diethyl fumarate was also evidenced at higher degradation temperatures. The amount of monomer increased with increasing degradation temperature. The dependence of the molar mass of the residual polymer on the degradation time and temperature was established and the number of main-chain scissions per monomer unit, s/P₀, calculated. A thermal degradation mechanism including de-esterification and random main-chain scission is proposed. The thermal degradation of PDEF was compared to the thermolysis of poly(ethyl methacrylate) (PEMA), poly(diethyl itaconate) (PDEI) and poly(ethyl acrylate) (PEA).     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008     

Photo- and radiation-induced degradation of vinyl polymers in solution. I. Oxidative degradation of poly(α-methylstyrene) initiated by photodecomposition of AIBN

The oxidative degradation of poly(α-methylstyrene) initiated by the photodecomposition of azobisisobutyronitrile was studied at 30°C in benzene solution. The progress of the reaction was followed by measuring the rate of chain scission of the polymer. It has been confirmed by GPC measurements that random scission of the polymer chain occurs in the present system. Chain scission did not occur in the absence of AIBN and oxygen. The rate was proportional to the initiation rate and independent of polymer concentration and oxygen pressure under these experimental conditions. Phenol was an effective inhibitor to this reaction. The mechanism of chain scission during oxidation is discussed, and a six-membered transition is proposed.     

Effects of orientation on dynamic shear behavior of some amorphous polymers from 4.2° to 300°K

The dynamic shear behavior of four highly amorphous polymers in the unstretched and stretched states (draw ratios 3:1 to 6:1) was investigated with a torsion pendulum at temperatures from 4.2°K to 180–300°K and frequencies from 0.4 to 3.2 cps. The polymers studied were polystyrene, poly(vinyl acetate), poly(vinyl propionate), and poly(isobutyl vinyl ether). Previously unreported loss maxima were found at 48°K (1.5 cps) and 149°K (1.3 cps) for poly(vinyl proplonate), at 10°K (1.0 cps) for poly(vinyl acetate) and at 9°K (1.6 cps) for poly(isobutyl vinyl ether). Uniaxial orientation increased the shear storage modulus G, measured with the torsion axis parallel to the stretch direction and caused changes in the loss peaks which depended on the polymer material studied.     

Heat and radiation effect on the degradation behaviors of polymeric liquids

We propose a mathematical model based on continuous-mixture kinetics to describe the degradation mechanism of polymeric material. Chu’s distribution function is employed to represent molecular-weight distributions of decomposed polymers. Calculated results agree fairly well with experimental observations for polymer degradation. The radiation damage is demonstrated as a number of chain scissions caused and G value for the scission that is defined as a number of radiolysis events caused by the absorption of 100 eV of radiation.     

Radiation degradation susceptibility of vinyl polymers: Nitriles and anhydrides

The effect of γ irradiation on a series of vinyl polymers, which included polymethacrylonitrile, poly(α-chloroacrylonitrile), poly(dimethyl itaconate), poly(acrylic anhydride), and poly(methacrylic anhydride), was studied as part of a program to develop improved positive lithographic resists. Radiation-induced degradation was observed for polymethacrylonitrile, poly(α-chloroacrylonitrile), and poly(methacrylic anhydride). Molecular weight degradation as a function of dose was monitored by membrane osmometry or GPC techniques. For γ-irradiated poly(dimethyl itaconate) and poly(acrylic anhydride) crosslinking was found to predominate over chain scission. [G(s)–G(x)] values, calculated from molecular weight inverse versus dose curves, indicate that both nitrile polymers degraded more efficiently than a poly(methyl methacrylate) reference standard on the basis of M _n changes. The radiation behavior of the first three polymers confirms earlier findings than vinyl polymers with quaternary carbons predominantly degrade when subjected to ionizing radiation.     

Structure and thermal behaviors of poly(vinyl alcohol)/surfactant composites: Investigation of molecular interaction and mechanism

Poly(vinyl alcohol) (PVA) is a promising biocompatible polymer, whose applicability is limited by its narrow processing window. Here, we adopted a facile approach to broaden the processing windows of PVA based on phosphoric ester of poly(ethylene oxide) (10) nonylphenyl (NP‐10P). Thermal analysis shows that both the melting temperature (T_m) and the glass transition temperature (T_g) of PVA decrease noticeably as NP‐10P content increases, indicating good miscibility of NP‐10P with PVA. The thermal degradation kinetics suggests composites display excellent thermal stability compared with neat PVA. The pyrolysis mechanism of PVA before and after modification with NP‐10P varies from chain unzipping degradation followed by chain random scission to chain random scission. The processing window of PVA is broadened from 9°C to 98°C with low content NP‐10P (5 wt%). Moreover, the composites maintain significant mechanical performance and transparency. This work provides an environmentally friendly and economical method to improve the possibility of thermal melt processing for PVA.     

Effect of temperature and solvents on stereospecific polymerization of vinyl alkyl ethers catalyzed by aluminum sulfate–sulfuric acid complex

The effect of polymerization temperature and solvents was determined on the crystallinity of polymers of vinyl isobutyl ether and of vinyl n-butyl ether prepared with aluminum sulfate–sulfuric acid complex catalyst. Principally, the methyl ethyl ketone (MEK)-insoluble fractions of these polymers were used for characterization. Density, per cent crystallinity by x-ray diffraction, infrared ratio, and dilatometric volume contraction of these polymer fractions were used as criteria of crystallinity. The MEK-insoluble fractions of poly(vinyl n-butyl ethers) prepared in carbon disulfide in the temperature range of ?30 to +25°C did not show any significant difference in the values of the above crystallinity parameters. The polymer obtained at 50°C. was less crystalline than the rest of the polymers. The MEK-insoluble fractions of poly(vinyl isobutyl ethers) prepared at 0–50°C. in carbon disulfide and n-heptane solvents also did not significantly differ in their degree of crystallinity. They were, however, decidedly less crystalline than the MEK-insoluble fractions of the corresponding polymers obtained at ?20°C. These data a indicate that on increasing the temperature of polymerization the crystallinity of the polymers was either unchanged or decreased slightly. The polymerizations of vinyl n-butyl ether and vinyl isobutyl ethers were also carried out in binary mixtures of carbon disulfide with n-heptane, chlorobenzene, and MEK. Generally, increasing the concentration of carbon disulfide increased the inherent viscosities of polymers as well as the weight percentage of their MEK-insoluble fractions. The MEK-insoluble fraction of poly(vinyl isobutyl ether) prepared in carbon disulfide-MEK mixture (volume ratio 2:1) was isotactic and highly crystalline. Likewise, the MEK-insoluble fractions of two polymers of vinyl n-butyl ether prepared in MEK itself were also isotactic and highly crystalline. Compared to poly(tetramethylene oxide), these latter fractions exhibited less dependence of rate of crystallization upon temperature. Consequently, at low degrees of supercooling they crystallize much more rapidly than does poly(tetramethylene oxide).     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). II. Polymerization of vinyl acetate in the presence of crosslinked poly(vinyl alcohol)

It is a common view that poly(vinyl acetate) has many branches at the acetyl side group, but that the corresponding poly(vinyl alcohol) has little branching. In order to study the branching in poly(vinyl acetate) and poly(vinyl alcohol) which is formed by chain transfer to polymer, the polymerization of ¹⁴C-labeled vinyl acetate in the presence of crosslinked poly(vinyl acetate), which was able to be decrosslinked to give soluble polymers, was investigated at 60°C and 0°C. This system made it possible to separate as well as to distinguish the graft polymer from the newly polymerized homopolymer. Furthermore, the degree of grafting onto the acetoxymethyl group and onto the main chain were estimated. It became clear that, in the polymerization of vinyl acetate, chain transfer to the polymer main chain takes place about 2.4 times as frequently at 60°C as that to the acetoxy group and about 4.8 times as frequently at 0°C.     

Cationic Polymerization of Isobutyl Vinyl Ether in Solution by Radiation

The radiation-induced cationic polymerization of isobutyl vinyl ether in solutions of diethyl ether and methylene chloride was investigated under conditions where the monomer and solvents were dried with molecular sieves to high levels of dryness. The investigation covered the temperature range from -16 to 90° C, the dose-rate range from 10¹⁵ to 10²⁰ eV/ (g)(sec) (using both gamma rays and electrons), and the influence of diethyl ether and methylene chloride as solvents for the monomer.

For the solution of the monomer in diethyl ether, a very high overall activation energy of 29.7 kcal/mole was found, which decreased sharply to a value of 1.2 kcal/mole above 30° C. No such change was found for the monomer solution in methylene chloride.

The dose-rate dependence of the rate of polymerization for the monomer solution in methylene chloride was found to be close to unity over the entire dose-rate range investigated.     

Synthesis of vinyl‐terminated isotactic poly(propylene)

Isotactic poly(propylene)s with 60–80% vinyl chain‐end selectivity were synthesized with metallocene catalysts. Some of these vinyl‐terminated poly(propylene)s are highly stereoregular (mmmm pentads up to 95%) and have high crystalline melting points in the range of 140–150°C. Chain‐end analysis using ¹³C NMR indicates the vinyl chain‐ends in the polymer are most likely formed through β‐methyl elimination in the chain termination step.     

The thermal degradation of poly(vinyl acetate) and poly(ethylene-co-vinyl acetate), Part I: Experimental study of the degradation mechanism

The thermal degradation mechanism of poly(vinyl acetate) (PVAc) and poly(ethylene-co-vinyl acetate) (EVA) copolymers was investigated with solid-state NMR, thermogravimetry coupled with mass spectrometry and differential thermal analysis. Between 300 and 400 °C acetic acid is eliminated (deacetylation), leaving a highly unsaturated residue or polyene. The deacetylation of PVAc is autocatalytic. Upon incorporation of ethylene entities into the polymer backbone, autocatalysis disappears. Between 400 and 500 °C, the polyene will degrade further by chain scission reactions in inert conditions or aromatise in an oxidative environment into a char, and oxidised eventually into CO₂ beyond 500 °C.In inert conditions, the deacetylation step as well as the chain scission reaction shows endothermic effects. In an oxidative environment, large exothermal effects are found for each degradation step. This indicates the occurrence of additional oxidation reactions during deacetylation, an important reorganisation of the polyene during char formation and oxidation of the latter into CO₂.     

Synthesis of ABA‐triblock and star‐diblock copolymers with poly(2‐adamantyl vinyl ether) and poly(n‐butyl vinyl ether) segments: New thermoplastic elastomers composed solely of poly(vinyl ether) backbones

ABA‐type triblock copolymers and AB‐type star diblock copolymers with poly(2‐adamantyl vinyl ether) [poly(2‐AdVE)] hard outer segments and poly(n‐butyl vinyl ether) [poly(NBVE)] soft inner segments were synthesized by sequential living cationic copolymerization. Although both the two polymer segments were composed solely of poly(vinyl ether) backbones and hydrocarbon side chains, they were segregated into microphase‐separated structure, so that the block copolymers formed thermoplastic elastomers. Both the ABA‐type triblock copolymers and the AB‐type star diblock copolymers exhibited rubber elasticity over wide temperature range. For example, the ABA‐type triblock copolymers showed rubber elasticity from about ?53 °C to about 165 °C and the AB‐type star diblock copolymer did from about ?47 °C to 183 °C with a similar composition of poly(2‐AdVE) and poly(NBVE) segments in the dynamic mechanical analysis. The AB‐type star diblock copolymers exhibited higher tensile strength and elongation at break than the ABA‐type triblock copolymers. The thermal decomposition temperatures of both the block copolymers were as high as 321–331 °C, indicating their high thermal stability. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Determination of interaction parameter χ1, for poly(vinyl alcohol) and water in gels crosslinked from solutions

The Flory interaction parameter χ₁ of poly(vinyl alcohol)-water systems has been estimated as a function of temperature and volume fraction of PVA, the polymer having been crosslinked from solutions of the same in water. Values are reported for temperatures between 0°C and 90°C and polymer volume fractions between 0.03 and 0.12.     

Living cationic polymerization of vinyl ethers with a naphthyl group: Decisive effect of the substituted position on naphthalene ring

Living cationic polymerization of a vinyl ether with a naphthyl group [2‐(2‐naphthoxy)ethyl vinyl ether, βNpOVE] was achieved using base‐assisting initiating systems with a Lewis acid. The Et_1.5AlCl_1.5/1,4‐dioxane or ethyl acetate system induced the living cationic polymerization of βNpOVE in toluene at 0 °C. The living nature of this reaction was confirmed by a monomer addition experiment, followed by ¹H NMR and matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry (MALDI‐TOF‐MS) analyses. In contrast, the polymerization of αNpOVE was not fully controlled; under similar conditions, it produced polymers with broad molecular weight distributions. The ¹H NMR and MALDI‐TOF‐MS spectra of the resultant poly(αNpOVE) revealed that the products had undesirable structures derived from Friedel–Crafts alkylation. The higher reactivity of αNpOVE in electrophilic substitution reactions, such as the Friedel–Crafts reaction, was attributable to the greater electron density of the naphthyl ring, which was calculated based on frontier orbital theory. The naphthyl groups significantly affected the properties of the resultant polymer. For example, the glass transition temperatures (T_g) of poly(NpOVE)s are higher by approximately 40 °C than that of poly(2‐phenoxyethyl vinyl ether). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

The thermal degradation of poly(-(d)-β-hydroxybutyric acid): Part 2—Changes in molecular weight

Changes in molecular weight occur in poly(-(d)-β-hydroxybutyric acid) in the temperature range 170–200°C, at which latter temperature evolution of volatile products of degradation becomes significant. Two processes are involved in these changes in molecular weight. The more important is random chain scission at ester groups, which results in the formation of carboxyl and vinyl groups. Although this ultimately results in a drastic reduction in the molecular weight of the polymer, this is delayed in the early stages of the reaction by a condensation reaction between the terminal hydroxyl groups present in the original polymer and the terminal carboxyl groups, which were either originally present or formed in the chain scission process. This delay could have relevance to the industrial processing of this material.     

Stereochemistry in cationic polymerization of alkenyl ethers. II. Formation of poly(ß-substituted vinyl ether)s with erythro-meso structures

The formation of polymers with erythro-meso structures, which could not be obtained from propenyl ethers with BF₃O(C₂H₅)₂, was studied by ¹³C-NMR spectroscopy on poly(ß-substituted vinyl ether)s obtained under a variety of conditions of polymerization. It was established that poly(cis-ethyl propenyl ether) obtained with Al₂(SO₄)₃–H₂SO₄ complex in toluene at 0°C was a highly stereoregular polymer with an erythro-meso structure. Cis-2-chlorovinyl ethyl ether and cis-methyl and ethyl butenyl ethers also yielded polymers with erythro-meso structures under the same conditions. In addition, with BF₃O(C₂H₅)₂ at ?78°C these three cis isomers produced amorphous polymers with threo-meso, racemic, and, in a few cases, erythro-meso structures, whereas cis-ethyl propenyl ether produced polymers with only threo-meso and racemic structures by the same catalyst. On the other hand, all trans isomers produced stereoregular polymers with threo-meso structures with BF₃O(C₂H₅)₂ at ?78°C, regardless of their ß-substituents; no erythro-meso structures were found in the polymers obtained.     

Evaluation of crosslinking and scission yields in the degradation of polystyrene by γ-irradiation in air

A sample of polystyrene with narrow molecular weight distribution (M?_w/M?_n = 1.03) has been formed into a 3-mm sheet and subjected to γ-irradiation at 25°C in air. Simultaneous crosslinking and scission of polymer chains resulted. Analyses by velocity and equilibrium sedimentation, gelpermeation chromatography, and osmometry of the polystyrene subjected to doses in the range 0-90 Mrad, all within the pre-gel region, have yielded average values of G(S) = G(X) = 0.022 ± 0.002 for the complete sample. Combination of these various experimental techniques has been successful in yielding consistent values of G(S) and G(X) and should be applicable with advantage to other polymers, particularly when neither G(S) nor G(X) is zero. The wide variation in literature values of G(S) and G(X) for irradiation of polystyrene under vacuum precludes any unequivocal conclusion on the effect of air on the radiation yields.     

Stereospecific polymerization of isobutyl vinyl ether catalyzed by calcined iron sulfate

The polymerization of isobutyl vinyl ether was studied in a heterogeneous system using iron (II) sulfate calcined in air at various temperatures as a catalyst. The maximum activity was shown by the catalyst calcined at 700°C, which effected the polymerization at room temperature in a few seconds, while the sulfate treated at 750°C was totally inactive. Poly(vinyl ethyl ether) was also obtained by the FeSO₄ (700°C) catalyst at room temperature. This catalyst formed the crystalline polymer (melting temperature 135–138°C) when the reaction was performed in toluene as solvent at room temperature. Poisoning experiments with Hammett indicators were carried out with the FeSO₄ (700°C) catalyst. The treatment with n-butylamine rendered it inactive in the reaction of isobutyl vinyl ether, while its catalytic activity was little affected by dicinnamalacetone. On the basis of the observed results, the nature of active sites of catalyst is discussed.     

Living cationic polymerization of dihydrofuran and its derivatives

Cationic polymerization of 2,3‐dihydrofuran (DHF) and its derivatives was examined using base‐stabilized initiating systems with various Lewis acids. Living cationic polymerization of DHF was achieved using Et_1.5AlCl_1.5 in toluene in the presence of THF at 0 °C, whereas it has been reported that only less controlled reactions occurred at 0 °C. Monomer‐addition experiments of DHF and the block copolymerization with isobutyl vinyl ether demonstrated the livingness of the DHF polymerization: the number–average molecular weight of the polymers shifted higher with low polydispersity as the polymerization proceeded after the monomer addition. Furthermore, this base‐stabilized cationic polymerization system allowed living polymerization of ethyl 1‐propenyl ether and 4,5‐dihydro‐2‐methylfuran at ?30 and ?78 °C, respectively. In the polymerization of 2,3‐benzofuran, the long‐lived growing species were produced at ?78 °C. The obtained polymers have higher glass transition temperatures compared to poly(acyclic alkyl vinyl ether)s. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4495–4504, 2008