纳米二氧化钛负载棉织物的制备及性能

以棉织物为基体,通过紫外辐照和超声法将不同表面性质的TiO_2纳米粒子负载到棉织物上,制备自清洁材料.利用扫描电子显微镜、能谱分析、接触角、紫外-可见光谱及降解甲基橙溶液等手段分别对样品表面的结构形貌、元素分布、光催化活性、紫外屏蔽性能和耐久性等进行分析.结果表明,棉织物经紫外辐照后,TiO_2纳米粒子与其结合更牢固,耐久性更佳;TiO_2负载后的棉织物表现出超疏水性能及优异的光催化活性和紫外屏蔽性能;与未改性的TiO_2纳米粒子相比,由聚乙烯醇(PVA)改性的TiO_2纳米粒子制备的自清洁棉织物的可见光光催化活性更高,其可见光的光催化效率是前者的3.9倍.PVA改性的纳米TiO_2对290~400 nm范围内的紫外光有较好的吸收作用,其紫外屏蔽效果更佳.     

Gold nanoparticles located at the interface of anatase/rutile TiO2 particles as active plasmonic photocatalysts for aerobic oxidation

Visible-light irradiation (λ > 450 nm) of gold nanoparticles loaded on a mixture of anatase/rutile TiO(2) particles (Degussa, P25) promotes efficient aerobic oxidation at room temperature. The photocatalytic activity critically depends on the catalyst architecture: Au particles with <5 nm diameter located at the interface of anatase/rutile TiO(2) particles behave as the active sites for reaction. This photocatalysis is promoted via plasmon activation of the Au particles by visible light followed by consecutive electron transfer in the Au/rutile/anatase contact site. The activated Au particles transfer their conduction electrons to rutile and then to adjacent anatase TiO(2). This catalyzes the oxidation of substrates by the positively charged Au particles along with reduction of O(2) by the conduction band electrons on the surface of anatase TiO(2). This plasmonic photocatalysis is successfully promoted by sunlight exposure and enables efficient and selective aerobic oxidation of alcohols at ambient temperature.     

Titania supported gold nanoparticles as photocatalyst

This Perspective is focused on the photocatalytic activity of gold nanoparticles supported on titania (Au/TiO(2)). Titania is the most widely used photocatalyst, but its limited activity under visible light irradiation has motivated the quest for modified titania materials absorbing visible light. The review starts by justifying how doping with metallic elements is a related strategy, but different, to that leading to the use of Au/TiO(2) in photocatalysis. Data supporting and confirming the photoactivity of gold nanoparticles in colloidal solutions are briefly presented to justify the possibility of gold photosensitization of titania by electron injection into the conduction band. After describing the most common procedures used to prepare Au/TiO(2), the central part of this article is focused on the photocatalytic activity reported for Au/TiO(2) for hydrogen generation, dye decoloration, phenol decomposition and carboxylic acid degradation, among other processes. Emphasis is given to the role that parameters like Au loading, particle size, surface area, spatial structuring and others play on the photocatalytic activity. One important issue has been to distinguish those reports using visible light from those other in which direct titania excitation by UV light has been used. These Au/TiO(2) photocatalysts can find real applications in the near future for environmental remediation and for hydrogen generation.     

Influence of Excitation Wavelength (UV or Visible Light) on the Photocatalytic Activity of Titania Containing Gold Nanoparticles for the Generation of Hydrogen or Oxygen from Water

Gold nanoparticles supported on P25 titania (Au/TiO(2)) exhibit photocatalytic activity for UV and visible light (532 nm laser or polychromatic light λ > 400 nm) water splitting. The efficiency and operating mechanism are different depending on whether excitation occurs on the titania semiconductor (gold acting as electron buffer and site for gas generation) or on the surface plasmon band of gold (photoinjection of electrons from gold onto the titania conduction band and less oxidizing electron hole potential of about -1.14 V). For the novel visible light photoactivity of Au/TiO(2), it has been determined that gold loading, particle size and calcination temperature play a role in the photocatalytic activity, the most active material (Φ(H2) = 7.5% and Φ(O2) = 5.0% at 560 nm) being the catalyst containing 0.2 wt % gold with 1.87 nm average particle size and calcined at 200 °C.     

A Facile One‐Pot Synthesis of Layered Protonated Titanate Nanosheets Loaded with Silver Nanoparticles with Enhanced Visible‐Light Photocatalytic Performance

Layered protonated titanate nanosheets (LPTNs) loaded with silver nanoparticles are prepared by a simple one‐pot hydrothermal route in silver‐ammonia solution. The as‐synthesized Ag‐loaded LPTNs possess large specific surface area. The Ag nanoparticles are highly dispersed on the surface of the LPTNs. They have negligible effects on the crystal structure, crystallinity, and surface area of the LPTNs but result in considerable enhancement of visible‐light absorption and in a red‐shift of the band gap for the LPTNs. The Ag‐loaded LPTNs show enhanced photocatalytic activity for both liquid‐ and gas‐phase reactions under visible‐light irradiation. Moreover, the photocatalytic activity first increases gradually with increasing Ag loading content, and then decreases after maximizing at an optimal Ag content. At the Ag loading content of 2.87 mol % and 1.57 mol %, the Ag‐loaded LPTNs exhibit the highest visible‐light photocatalytic activity for degradation of rhodamine B in water and mineralization of benzene in air, respectively. An alternative possible mechanism for the enhancement of the visible‐light photocatalytic activity is also proposed.     

Au Nanoparticles Loaded on Hollow TiO2 Microspheres with (001) Exposed Facets: a Strategy for Promoting Photocatalytic Performance

Au nanoparticles loaded TiO₂ hollow microspheres with exposed (001) facets(Au-HTFs) were synthesized through template-free hydrothermal process combined with a chemical reduction role. Au-HTFs displayed excellent photocatalytic activity in catalyzing oxidization reaction in organic pollutant system, which originates from the synergistic effect of the reactive (001) facets and Au nanoparticles with a wide range of absorption in visible region based on localized surface plasmon resonance effect. The unique synergistic effect could largely increase the photocatalytic performance resulting from the improvements of both the visible light aborption and the recombination of electron-hole pairs. Our findings revealed that among Au-HTFs with different Au loading percentages, Au-HTFs with 2%(mass fraction) Au loading possessed the superior photocatalytic activity.     

Bi6Fe1.9Co0.1Ti3O18纳米片负载Au尺寸对其可见光光催化性能的影响

我们通过一种简单的化学方法制备了具有可见光催化性能的Bi₆Fe_1.9Co_0.1Ti₃O₁₈/Au（BFCTO/Au）纳米复合材料。结果表明,通过负载不同颗粒大小的Au纳米颗粒（~23 nm、~36 nm、~55 nm和~80 nm）,BFCTO的可见光光催化性能明显增强,其中负载粒径为~23 nm的Au纳米颗粒的BFCTO/Au-1样品的可见光光催化效率最高。     

Photocatalytic Degradation of 2-Propanol and Phenol Using Au Loaded MnWO4 Nanorod Under Visible Light Irradiation

Single crystalline MnWO₄ nanorod has been prepared by low temperature hydrothermal reaction at 180 °C. The prepared MnWO₄ possesses band gap of 2.63 eV. Photochemical decomposition method has been followed to disperse Au nanoparticles onto MnWO₄ nanorod. The prepared Au loaded MnWO₄ nanorod demonstrated greatly enhanced photocatalytic activity in decomposing 2-propanol and evolving CO₂ in gas phase and phenol in aqueous phase compared to bare MnWO₄ and commercial TiO₂ nanoparticles (Degussa P25) under visible light (λ ≥ 420 nm) irradiation. The Au loading was optimized to 3.79 wt% for the highest efficiency. The enhanced photocatalytic activity originates from the absorption of visible light by MnWO₄ as well as the introduction of nanoparticulate Au on the surface of MnWO₄ as cocatalyst to impede the recombination of photogenerated charge-carriers.     

负载金的掺氮二氧化钛的制备及其可见光催化性能

以纳米管钛酸为前驱体,采用水热法先制备得到新型N掺杂二氧化钛,然后用沉积沉淀法在N掺杂二氧化钛表面负载微量贵金属Au,制备得到负载Au的掺N二氧化钛.利用TEM、XRD、XPS、ESR和DRS等手段研究了样品的形貌、晶体结构、元素化学态和光谱吸收性质.样品光催化活性通过可见光催化降解丙烯进行评价,结果表明,样品N-TiO₂和Au/N-TiO₂具有明显的可见光(λ≥420 nm)催化活性.ESR结果表明,掺氮过程中生成的束缚单电子的氧空位是样品具有可见光响应的原因.     

铽负载介孔二氧化钛的制备、表征和协同效应

以嵌段共聚物P123为模板剂,采用蒸发诱导自组装法制备了铽负载介孔TiO2光催化剂,并利用XRD、N2吸附解吸和UV-Vis吸收光谱等技术手段对样品进行了表征。 制备的样品为锐钛矿和金红石混合晶相,以罗丹明B为模拟有机降解物,样品显示了良好的可见光催化活性。 研究发现0.7%的铽负载和380 ℃的煅烧温度是较佳的制备条件。 介孔结构所具有的高的比表面积、小的晶粒尺寸、铽负载诱导的电荷分离和可见光吸收增强协同提高了光催化活性。 同时,提出了铽负载二氧化钛诱导增强光催化作用的机理。     

One-step solvothermal synthesis of N-doped TiO2 nanoparticles with high photocatalytic activity in the reduction of aqueous Cr（Ⅵ）

N-doped TiO2 （N-TiO2） nanoparticles were synthesized via a one-step low temperature （180℃） solvothermal route, which adopted NH4NO3 as the nitrogen source. The structure, composition, BET specific surface area, and optical properties of the as-synthesized product were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, N2 adsorption- desorption isotherms, and UV-vis diffuse reflectance spectroscopy. In addition, its photocatalytic properties were tested by the reduction of aqueous Cr（VI） under UV and visible light （x 〉 420 rim） irradiation. It was observed that for the reduction of aqueous Cr（VI）, the as-synthesized N-TiO2 nanoparticles not only exhibited much higher photocatalytic activity than P25 TiO2 under UV light, but also exhibited remarkably high photocatalytic activity under visible light （λ 〉 420 nm）.     

金/氧化亚铜异质球的制备及其可见光催化性能

使用L-半胱氨酸作为连接剂, 利用硼氢化钠原位还原预先吸附在介孔氧化亚铜表面的氯金酸根离子,得到了Au/Cu₂O异质结构. 应用X射线粉末衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱和N₂物理吸附等手段对催化剂进行表征, 并以λ>400 nm的可见光作为光源, 评价了该催化剂光催化降解亚甲基蓝(MB)的活性. 实验结果表明, 直径为4 nm的金颗粒完好地负载在介孔氧化亚铜的表面, 并且介孔氧化亚铜的细微结构与孔径均未发生变化. 研究表明, 以乙醇作为反应溶剂有效抑制了AuCl₄^-与Cu₂O之间的氧化还原反应, 从而有利于氧化亚铜介孔结构的保持及金颗粒的原位还原. 光催化降解亚甲基蓝的结果表明, Au/Cu₂O异质结构的光催化活性比纯氧化亚铜光催化活性有明显提高. 推测其光催化性能提高的主要原因如下: 一方面, 金颗粒良好的导电性有利于氧化亚铜表面电子的快速转移, 实现电子-空穴分离; 另一方面, 金颗粒可能存在的表面等离子共振现象加速了光生电子的产生.     

TiO2晶型对Au/TiO2上光催化分解臭氧的影响

以不同晶型TiO2为载体,采用沉积-沉淀法制备了Au/TiO2光催化剂,并用紫外-可见漫反射光谱、X射线光电子能谱(XPS)和表面光电压谱(SPS)等手段进行了催化剂表征,详细考察了Ti O2晶型对Au/TiO2光催化分解臭氧活性的影响.结果表明,光催化分解臭氧的活性顺序为Au/P25>Au/Anatase>Au/Rutile,这与不同的单一Ti O2对光催化臭氧分解的活性顺序是一致的.但在TiO2上沉积金后,其对光催化臭氧的分解活性有了显著的提高.由催化剂的Au4fXPS分析发现,不同晶型Ti O2上的电荷向金簇迁移的能力有明显差异,加之载体本身对光催化臭氧分解活性不同,两者协同作用导致负载金催化剂光催化分解臭氧活性的不同.SPS信号强度与催化剂光催化活性有很好的对应关系,SPS信号越强,光生电子和空穴分离效率越高,光催化活性越好.     

水热法制备铂掺杂二氧化钛及其可见光催化性能

以纳米管钛酸为前驱体,采用水热法制备了Pt掺杂TiO2样品.水热反应过程中,纳米管钛酸表面羟基与氯铂酸发生酸碱中和反应,导致反应后pH值升高;在130°C开始纳米管钛酸晶体结构由正交晶系转变为锐钛矿相TiO2.表面化学组成分析表明,掺杂的Pt主要以+2价形式存在.以丙烯为模型污染物,评价样品的可见光(λ≥420nm)光催化活性.结果表明,Pt-TiO2具有明显的可见光光催化降解丙烯的活性,其中160°C水热处理制得的Pt-TiO2活性最高.最后讨论了低温水热法Pt掺杂的形成机理及Pt-TiO2具有可见光响应的原因.     

TiO2/Au纳米棒阵列的制备及其光催化性能

采用电沉积和旋转涂膜相结合的方法成功制备了高度有序的TiO2/Au纳米棒阵列催化剂.扫描电镜和透射电镜结果表明,TiO2薄膜均匀地包覆在Au纳米棒的表面,形成核壳型的一维阵列结构.X射线衍射分析表明所获得TiO2为(101)晶面优先生长的锐钛矿晶相.紫外-可见漫反射光谱显示,由于Au和TiO2间肖特基结的存在造成吸收红...     

Synthesis of Mg-Doped TiO2 nanoparticles under different conditions and its photocatalytic activity

In this study, TiO(2)- and Mg-doped TiO(2) nanoparticles with different dopant contents were prepared by sol-gel method. The prepared photocatalysts were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET) and diffuse reflectance spectroscopy (DRS) techniques. The results of BET analysis indicated a pore diameter of 8 nm and surface area of 48.5 m(2) g(-1). XRD patterns of pure and doped TiO(2) nanoparticles at 450 °C revealed that all phases are anatase. The particle size obtained from TEM was less than 20 nm. The band gap energy of Mg-doped TiO(2) nanoparticles was lower than that of TiO(2) . The photocatalytic activity of the pure and doped nanoparticles has been compared in the removal of C.I. Acid Red 27 (AR27). The photocatalytic activity of Mg-doped (0.2 mol%) TiO(2) for the degradation of AR27 was higher than that of bare TiO(2) nanoparticles. Results of total organic carbon analysis and changes in the AR27 UV-Vis peaks indicated 99% mineralization and extinguishing of all peaks in UV and visible regions is possible with Mg-doped TiO(2) nanoparticles. Removal efficiency of AR27 was sensitive to the parameters such as catalyst dose, pollutant concentration and light intensity.     

Ag／TiO2复合纳米催化剂的制备和表征及其光催化活性

 采用光还原沉积贵金属法，制备了Ag／TiO2复合纳米催化剂．通过调节溶液的pH值控制TiO2表面负载银的形貌，利用AAS，XRD，TEM和XPS等手段对样品进行了表征．以苯胺氧化为模型反应，考察了Ag／TiO2复合纳米催化剂样品的光催化活性以及银沉积量和沉积形貌对催化剂活性的影响．结果表明，通过调控光还原沉积条件，可在平均粒径为24nm左右的TiO2颗粒上获得3nm左右均匀分散的银粒子；在TiO2上沉积适量的具有较高分散度的金属Ag，能有效提高TiO2对苯胺氧化反应的光催化活性．     

Size-dependence of Fermi energy of gold nanoparticles loaded on titanium(iv) dioxide at photostationary state

TiO(2) particle-supported Au nanoparticles (NPs) with varying sizes and good contact (Au/TiO(2)) were prepared under a constant loading amount by the deposition-precipitation method. The Fermi energy of Au NPs loaded on TiO(2) at the photostationary state (E(F)') was determined in water by the use of S/S(2-) having specific interaction with Au as a redox probe. The E(F)' value goes up as the mean size of Au NPs (d) increases at 3.0 相似文献   

Synthesis and characterization of sulfur-titanium dioxide nanocomposites for photocatalytic oxidation of cyanide using visible light irradiation

A sol-gel method was used to prepare TiO2and sulfur-TiO2(S-TiO2)nanocomposites, which were characterized by N2 adsorption-desorption, X-ray diffraction, X-ray photoelectron spectroscopy, photoluminescene, ultraviolet visible and transmission electron microscopy measurements. The photocatalytic performance of TiO2 and S-TiO2nanocomposites, with respect to the photocatalytic oxidation of cyanide under visible light irradiation, was determined. The results reveal that S is well dispersed on the surface of TiO2 nanoparticles. Additionally, the surface area of the S-TiO2nano-composites was observed to be smaller than that of the TiO2nanoparticles because of blocked pores caused by doping with S. The S-TiO2nanocomposite (0.3 wt% S) exhibited the lowest band gap and the highest photocatalytic activity in the oxidation of cyanide. The photocatalytic performance of S-TiO2(0.3 wt% S) nanocomposites was stable, even after the fifth reuse of the nanoparticles for the oxidation of cyanide.     

可见光响应的LaVO4/TiO2 纳米管的合成、表征及对气相甲苯的光催化性能

通过水热方法合成了可见光响应的LaVO4/TiO2纳米管, 采用XRD, TEM, 氮气吸附-脱附以及表面光电压谱对样品进行了表征. 以气相甲苯为典型污染物, 研究了制备样品在可见光(λ＞420 nm)条件下的光催化性能. 实验结果表明, LaVO4的复合使TiO2的粒径减小, 比表面积增大, 光响应范围向可见光偏移. 光催化实验结果表明, 在可见光条件下, LaVO4/TiO2纳米管降解甲苯的效率比其它样品高, 与纯TiO2纳米管相比, 降解效率提高了47%.