微波促进下2,5-二取代-1,3,4-(口恶)二唑衍生物的合成

报道了微波促进无溶剂条件下二酰基肼可以良好产率脱水闭环得到2，5-二取代-1，3，4-E二唑衍生物。反应产率受取代基影响较大，苯基取代时产率较高，烷基取代时产率较低；反应产率与所用的无机支持有关，其中以酸性三氧化二铝的效果最佳。此法不仅环境友好且操作安全，避免使用化学脱水剂。     

新型含硫高折光指数光学树脂单体MPSDMA的合成及其共聚树脂的性能研究

通过氯磺化反应,还原反应和低温相转移仙化反应合成了一种新型光学树脂单体合成 4,4′-二巯基二苯硫醚双甲基丙烯酸酯（MPSDMA）,。成功地将苯环、含硫基团和双键引入光学树脂单体结构中,将MPSDMA分别与甲基丙烯酸甲酯（MMA）和苯乙烯（St)通过自由基共聚制成透明树脂,共聚树脂性能的研究表明该类新型光学树脂具有高折光指数,高表面硬度等特点。     

新型2-(4-甲硫苯氧基)-4H-咪唑啉-4-酮衍生物的合成与杀菌活性

由膦亚胺，芳基异氰酸酯和4-甲硫苯酚反应制得2-(4-甲硫苯氧基)-4H-咪唑啉-4-酮衍生物，该衍生物显示出杀菌活性。     

低压加氢法制备1,4-环己烷二甲醇的研究

1,4-环己烷二甲醇是生产改性聚酯的中间单体。采用铜系催化剂，以1,4-环己烷二甲酸二甲酯为原料，低压加氢生成1,4-环己烷二甲醇。考察了反应温度、反应压力等对反应活性的影响，进行了200 h的催化剂寿命评价，并对催化剂进行了表征。结果表明，在反应温度200 ℃，反应压力3.0 MPa的条件下，1,4-环己烷二甲酸二甲酯的转化率大于95%，1,4-环己烷二甲醇的选择性大于98%，XRD谱图说明金属铜是该催化剂的主要活性中心。     

ACPMA/BPO引发甲基丙烯酸甲酯聚合及其动力学

以4,4′-偶氮二[4-氰基戊酰(对-二甲氨基)苯胺](ACPMA)/过氧化二苯甲酰(BPO)为氧化还原引发体系,研究了甲基丙烯酸甲酯(MMA)在N,N-二甲基甲酰胺(DMF)中的聚合及其动力学行为.考察了聚合反应温度、单体浓度、ACPMA浓度和BPO浓度对聚合反应速率和聚合物分子量的影响,测定了反应级数和聚合反应的活化能.结果表明,在一定范围内,聚合反应速率随单体浓度增大、ACPMA浓度增大、BPO浓度增大和反应温度的升高而增大;聚合物分子量随单体浓度的增大而增大,随ACPMA浓度的增大、BPO浓度增大和反应温度的升高而降低.该体系具有氧化还原引发体系的特征,其引发MMA的聚合速率方程为Rp=K[ACPMA]0.57     

含X-型二维液晶基元和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-14-冠-4冠醚环液晶共聚酯的合成与表征

以4,4′-(α,ω-辛二酰氧)二苯甲酰氯(M1)、2,5-二(对十二烷氧基苯甲酰氧基)对苯二酚(M2)和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-14-冠-4(M3)为单体,通过溶液共缩聚反应,合成了一系列含X-型二维液晶基元和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-14-冠-4冠醚环的主链型液晶共聚酯.单体1(M1)由对羟基苯甲酸和辛二酰氯,通过酯化和取代反应制备,单体2(M2)由2,5-二羟基苯醌和对十二烷氧基苯甲酰氯通过酯化和还原反应制备,单体3(M3)由顺式-二氨基二苯并-14-冠-4和苯酚通过重氮化和偶联反应制备.共聚酯的分子量不高,[η]在0·35~0·25dL/g之间.单体的化学结构通过IR、UV、1H-NMR、MS和元素分析等方法确证.共聚酯的外观为黄色粉状固体,除CP9外,室温下不溶于CHCl3和THF溶剂.共聚酯的性质采用GPC、[η]、DSC、TG、WAXD和POM等方法进行了研究.发现所有的共聚酯加热到各自的熔融温度以上都能形成液晶态,在液晶态可以观察到向列相的丝状织构或纹影织构.共聚酯的熔融温度(Tm)和各向同性温度(Ti)随共聚酯分子中顺式-4,4′-双(4-羟基苯基偶氮)二苯并-14-冠-4用量的改变呈规律性变化.WAXD研究进一步证实了共聚酯的液晶性.     

对硝基甲苯氧化缩合制备4,4‘—二硝基ZHi

4,4′-二硝基(FDA1)(下称C)是制备多种荧光染料、药物及助剂的中间体.可通过Wittig反应[1,2]、苄基卤代物碱性缩合反应[3]、乙烯在钯盐催化下的芳基化反应[4]、活性芳甲基衍生物的二缩合反应[5]等方法制得.以对硝基甲苯(下称A)氧化缩合,合成4,4′-二硝基(FDA1)尚无专门报道.鉴于原料廉价、易得、合成工艺简单,极具应用价值.本文利用该法合成了4,4′-二硝基(FDA1),并对其进行了表征和工艺条件研究.     

四配位硅单体及其共聚物的制备和结构表征

研究了直接从无定形二氧化硅出发, 与乙二醇、氢氧化钾反应, 生成高反应活性的五配位硅钾化合物, 并以此为原料与含活泼氯的3-氯丙烯反应制备出含双键官能团的四配位硅单体. 讨论了合成单体的条件如温度、反应时间、反应物浓度、溶液pH值及溶剂等因素的影响. 然后以该四配位硅单体与甲基丙烯酸甲酯(MMA)在偶氮二异丁腈(AIBN)作引发剂下进行自由基聚合得到支链含硅共聚物. 并借助于红外光谱(IR)、核磁共振(¹³C和¹H, ²⁹Si)、能谱元素分析对合成的单体进行了结构表征; 用红外光谱(IR)、热失重谱(TG)、差示扫描量热谱(DSC)、凝胶渗透色谱法(GPC)等现代测试手段对支链含硅共聚物进行了结构表征及热性能分析. IR表明四配位硅单体在1646 cm^－1处是C＝C的伸缩振动吸收峰, 在共聚物中此峰消失; TG表明共聚物在249.6 ℃才开始失重, 552 ℃有机部分失重完毕; GPC分析表明共聚物的数均分子量为8.7万.     

含X-型二维液晶基元和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6冠醚环液晶共聚酯的合成与表征

以4,4'-(α,ω-辛二酰氧)二苯甲酰氯(M1)、2,5-双[4-'(对癸氧基苯基)苯甲酰氧基]对苯二酚(M2)和顺式-4,4'-双(4-羟基苯基偶氮)二苯并-18-冠-6(M3)为单体,通过溶液共缩聚反应,合成了一系列新的含X-型二维液晶基元和顺式-4,4'-双(4-羟基苯基偶氮)二苯并-18-冠-6冠醚环的主链犁液晶共聚酯.单体1(M1)由对羟基苯甲酸和辛二酰氯,通过酯化和取代反应制备,单体2(M2)由2,5-二羟基苯醌和对癸氧基苯基苯甲酰氯通过酯化和还原反应制备,单体3(M3)由顺式-二氨基二苯并-18-冠-6和苯酚通过重氮化和偶联反应制备.共聚酯的分子量小高,[η]在0.30～0.39之间.单体的化学结构通过 IR、UV、1H-NMR、MS 和元素分析等方法确证.共聚酯的外观为黄色粉状固体,除共聚酯 CP9 外,室温下不溶于 CHCl3 和 THF 溶剂.共聚酯的性质采用 GPC、[η]、DSC、TG、WAXD 和 POM 等方法进行了研究.发现所有的共聚酯加热到各自的熔融温度以上都能形成液晶态,在液晶态可以观察到近晶相和向列相的典型织构.共聚酯的熔融温度(Tm)和各向同性温度(T1)随共聚酯分子中顺式-4,4'-双(4-羟基苯基偶氮)二苯并-18-冠-6用量的改变呈规律性变化.WAXD 研究进一步证实了共聚酯的液晶性.     

含X-型二维液晶基元和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6冠醚环液晶共聚酯的合成与表征

以4,4-′(α,ω-辛二酰氧)二苯甲酰氯(M1)、2,5-双[4-′(对癸氧基苯基)苯甲酰氧基]对苯二酚(M2)和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6(M3)为单体,通过溶液共缩聚反应,合成了一系列新的含X-型二维液晶基元和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6冠醚环的主链型液晶共聚酯.单体1(M1)由对羟基苯甲酸和辛二酰氯,通过酯化和取代反应制备,单体2(M2)由2,5-二羟基苯醌和对癸氧基苯基苯甲酰氯通过酯化和还原反应制备,单体3(M3)由顺式-二氨基二苯并-18-冠-6和苯酚通过重氮化和偶联反应制备.共聚酯的分子量不高,[η]在0.30~0.39之间.单体的化学结构通过IR、UV1、H-NMR、MS和元素分析等方法确证.共聚酯的外观为黄色粉状固体,除共聚酯CP9外,室温下不溶于CHCl3和THF溶剂.共聚酯的性质采用GPC、[η]、DSC、TG、WAXD和POM等方法进行了研究,发现所有的共聚酯加热到各自的熔融温度以上都能形成液晶态,在液晶态可以观察到近晶相和向列相的典型织构.共聚酯的熔融温度(Tm)和各向同性温度(Ti)随共聚酯分子中顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6用量的改变呈规律性变化.WAXD研究进一步证实了共聚酯的液晶性.     

Melt-polymerizable bisimido-bisphthalonitriles containing silicon,fluoro, and ether groups: Synthesis,characterization, and NMR study

Various melt-polymerizable bisimido-bisphthalonitrile polymer precursors were synthesized by the reaction of 4-aminophthalonitrile (4-APN) with bis(3,4-dicarboxyphenyl) dimethylsilane dianhydride (SIDA), 4,4′-hexafluoroisopropylidene diphthalic anhydride (6FDA), bis(3,4-dicarboxyphenyl)ether dianhydride (ODPA), and 3,3′, 4,4′-tetracarboxylichenzophen+ne dianhydride (BTDA) in an aprotic solvent. The synthesized monomers showed crystalline melting at 269 and 271°C. Elemental analysis, differential thermal analysis (DTA), infrared (IR), nuclear magnetic resonance (¹H-NMR) and mass spectral studies were carried out to characterize the synthesized monomers. Thermogravimetric analysis (TGA) of the synthesized monomers showed their thermal stability at 410–400°C. A detailed study and NMR investigation of the first step of condensation reaction was carried out and indicated the formation of a transient charge transfer complex. Thermal cyclization of the formed intermediate, however, gave the required monomers. A preliminary study demonstrated that melt-polymerization of the synthesized monomers gave thermallystable, tough polymers.     

New silicon-containing heterocyclic polyimides

New aromatic polyimides and polyamide-imides with phenylquinoxaline rings and dimethylsilane units have been synthesized by solution polycondensation reaction of aromatic diamines containing phenylquinoxaline units with bis(3,4-dicarboxyphenyl)-dimethylsilane dianhydride, or with a diacid chloride resulting from the reaction of this dianhydride with p-aminobenzoic acid. These polymers were easily soluble in organic solvents, such as N-methylpyrrolidinone and dimethylacetamide, and showed high thermal stability with decomposition temperature being above 440°C and glass transition temperature in the range of 245-285°C. Very thin coatings were deposited from polymer solutions onto silicon wafers and exhibited smooth, pinhole-free surface in atomic force microscopy investigations. Some of these polymers showed blue fluorescence in solution and films, with a maximum in the range of 415-425 nm.     

Thermally polymerizable bisaryloxy-bisimido-bisphthalonitriles containing dimethylsilane,hexafluoroisopropylidene, ether,and keto groups: Synthesis,characterization, and NMR study

A proton-NMR study of the condensation reaction (step 1) of 4-(3′-aminophenoxy)phthalonitrile (4-3′APPN) ( I ) in an aprotic solvent with various aromatic dianhydrides demonstrated the formation of the corresponding bisamic acid within 5–10 min. There was no effect of the electron affinity of the used aromatic dianhydrides on the time of the condensation reaction and also no charge-transfer complex formation was indicated. Proton-NMR study of the synthesized bisaryloxy-bisimido-bisphthalonitriles at 250.1 MHz has revealed general findings for their NMR characterization. The coupling constant (J) value for the ortho-coupled protons of the phthalonitrile ring of the 4–3′-APPN portion is 8.8 ± 0.05 Hz and that for the ortho-coupled protons of the aminophenoxy ring of 4–3′-APPN is 8.1 ± 0.05 Hz. The coupling constant (J) values for ortho-coupled protons of the dianhydride portion range from 8.1 to 7.5 Hz. Various thermally polymerizable bisaryloxybisimido-bisphthalonitriles (BBBP) ( X, XI, XII , and XIII ) containing dimethylsilane, hexafluoroisopropylidene, ether, and keto groups, suitable for the development of thermooxidative stable, void-free composites, were synthesized by two methods. In method 1,4–3′-APPN ( I ) in N,N-dimethylacetamide (DMAC) was condensed (step 1) with bis(3,4-dicarboxyphenyl)dimethylsilane dianhydride (SIDA) ( II ), 4, 4′-hexafluoroisopropylidenediphthalic anhydride (6FDA) ( III ), bis(3,4-dicarboxyphenyl)ether dianhydride (ODPA) ( IV ), and 3,4,3′,4′-benzophenonetetracarboxylic dianhydride (BTDA) ( V ), respectively, to give the corresponding bisamic acids. Thermal cyclodehydration of the intermediate bisamic acid at 160°C gave the bisphthalonitriles. In method 2, the second step of thermal cyclodehydration was performed in situ in refluxing toluene. The characterization of the synthesized bisaryloxy-bisimido-bisphthalonitriles (BBBP) was performed using FT-IR, ¹H-NMR, ¹³C-NMR, mass spectroscopy, and elemental analysis. A preliminary study indicated that thermal-polymerization of these bisphthalonitriles (BBBP) gave tough, thermosetting polymers, useful for high-temperature applications. © 1993 John Wiley & Sons, Inc.     

Poly(1,3,4-oxadiazole-imide)s containing dimethylsilane groups

New poly(1,3,4-oxadiazole-imide)s containing dimethylsilane units have been prepared by solution polycondensation reaction of an aromatic dianhydride incorporating dimethylsilane group, namely bis(3,4-dicarboxyphenyl)dimethylsilane dianhydride, with different aromatic diamines having preformed 1,3,4-oxadiazole ring, such as 2,5-bis(p-aminophenyl)-1,3,4-oxadiazole, 2,5-bis[p-(4-aminophenoxy)phenyl]-1,3,4-oxadiazole, 2,5-bis[p-(3-aminophenoxy)phenyl]-1,3,4-oxadiazole, 2-(4-fluorophenyl)-5-(3,5-diaminophenyl)-1,3,4-oxadiazole, and 2-(4-dimethylaminophenyl)-5-(3,5-diaminophenyl)-1,3,4-oxadiazole. The polymers were easily soluble in polar organic solvents, such as N-methylpyrrolidinone, N,N-dimethylformamide, and pyridine, as well as in less polar organic solvents, such as tetrahydrofuran and chloroform. Very thin coatings deposited on silicon wafers exhibited smooth, pinhole-free surface in atomic force microscopy investigations. The polymers showed high thermal stability with decomposition temperature being above 415 °C.They exhibited a glass transition in the temperature range of 202-282 °C, with reasonable interval between glass transition and decomposition temperature. Solutions of the polymers in N,N-dimethylformamide exhibited fluorescence, having maximum emission wavelength in the range of 353-428 nm.     

Hydrogen‐bonded supramolecular polymers containing dimethylsilane groups: Synthesis,crystal structure,and characterization

Bis[N‐(4‐carboxyphenyl)phtalimidyl]dimethylsilane prepared by the reaction between bis(3,4‐dicarboxyphenyl)dimethylsilane anhydride and p‐aminobenzoic acid has been used to built three novel hydrogen‐bonded supramolecular polymers as a result of cocrystallization with pyridine derivatives: 4,4′‐bipyridyl ( SP1 ), 1,2‐bis(4‐pyridyl)ethylene ( SP2 ), and 4,4′‐azopyridine ( SP3 ). The structures of the dianhydride, diacid, and derived supramolecular polymers were investigated by Fourier transform infrared (FTIR) and proton magnetic resonance (¹H NMR) spectroscopy. Self‐assembling was proved by the presence of the IR absorption bands around 1900 and 2400 cm^?1 specific for hydrogen bond. The association constant values were estimated by using FTIR spectroscopy in solid state. According to X‐ray diffraction study, the bis(3,4‐dicarboxyphenyl)dimethylsilane anhydride ( 1 ) has an isolated molecular structure. Bis[N‐(4‐carboxyphenyl)phtalimidyl]dimethylsilane ( 2 ) molecules are associated in the crystal structure via dimeric O? H … O hydrogen bonds resulting in the wavy 1D supramolecular chain. The main packing motif for SP1 and SP3 is represented by wavy chain formed by alternating sequences of 4,4′‐bipyridyl or 4,4′‐azopyridine and bis[N(4‐carboxyphenyl)phtalimidyl]dimethylsilane molecules linked by O? H … N hydrogen bonds. Thermal behavior was studied by differential scanning calorimetry and thermogravimetric analysis. The ability for the structuration in film was emphasized by atomic force microscopy. The molecular transport ability of the reversible associations was estimated by dynamic water vapor sorption (DVS) analysis. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of silicon-containing phenylated soluble aramids

New high molecular weight (inherent viscosities, 1.21–0.50 dL/g) aramids having silicon and pendant phenyl groups were synthesized by low temperature interfacial polycondensation technique involving the reaction of acid chlorides: bis(4-chlorocarbonylphenyl)dimethylsilane and bis(3-chlorocarbonylphenyl)dimethylsilane with diamines: 2,5-bis(4-aminophenyl)-3,4-diphenyl-thiophene and bis(4-aminophenyl)ether. Copolyamides were obtained by using different proportions of these diamines. All the polymers were completely soluble in organic solvents such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and N,N-dimethylformamide. Thermal properties were evaluated by thermogravimetry which showed no weight loss below 325°C in both air and nitrogen atmospheres.     

吡啶桥联的聚酰亚胺的合成与性能研究

以3,4-二甲基苯乙酮与3,5-双(三氟甲基)苯甲醛为原料,通过Chichibabin反应制备了吡啶桥联的四甲基化合物,该化合物再经氧化、脱水反应制备了主链含有吡啶环、侧链带有双三氟甲基取代苯侧基的新型含氟芳香族二酐单体,2,6双(3′,4′-二羧基苯基)-4-(3″-,5″-双三氟甲基苯基)吡啶二酐(6FDAPA).FT IR、NMR、质谱以及元素分析等测试结果表明,6FDAPA的结构与预期的相符.利用6FDAPA与另外一种不含氟的二酐单体2,6双(3′,4′二羧基苯基)4苯基吡啶二酐(DAPA)分别与含氟二胺单体,1,4双(2三氟甲基4氨基苯氧基)苯(6FAPB)通过两步热亚胺化法制备了两种聚酰亚胺(PI)薄膜.测试结果表明,6FDAPA6FAPB(PI2)与DAPA6FAPB(PI1)相比具有相近的耐热性能,玻璃化转变温度为280℃,起始热分解温度为580℃、700℃时的重量保持率64.5%.同时PI2具有更为优良的透光性,紫外可见光谱(UV Vis)测试表明,PI2与PI1薄膜在450nm处的透光率分别为85.7%与69.4%.     

含有聚醚链段的可溶性聚酰亚胺气体分离膜材料及其性能

将4,4'-六氟亚异丙基-邻苯二甲酸酐(6FDA)和1,3-苯二胺(mPDA)与二端氨基聚醚缩聚, 得到含有聚醚柔性链段的聚酰亚胺气体分离膜材料. 所合成的共聚聚酰亚胺在N-甲基吡咯烷酮(NMP)和四氢呋喃(THF)等有机溶剂中具有良好的溶解性能. 研究了O2, N2, H2, CH4和CO2在聚酰亚胺均质膜中的渗透性能, 考察了二端氨基聚醚的含量、链长和化学结构对气体渗透性能的影响. 结果表明, 聚醚链段的引入增大了气体的扩散系数, 气体的渗透系数显著增大; 聚醚链段与CO2相对较强的相互作用, 增大了对CO2/N2的溶解选择性, CO2/N2的分离性能优于CO2/CH4, 同时CO2比H2优先透过膜.     

Synthesis and properties of oligomers containing substituted bithiazole rings

A series of novel polyimide and poly(Schiff base) oligomers containing substituted bithiazole rings were designed and synthesized, for the first time, by polycondensation of 5,5^′-dimethyl-2,2^′- diamino-4,4^′-bithiazole (MDABT) with dianhydrides (pyromellitic dianhydride, 3,3^′-4,4^′-benzophenone tetracarboxylic dianhydride and bis (3,4-dicarboxyphenyl) ether dianhydride), and dialdehydes (oxalic aldehyde, isophthalaldehyde and terephthalaldehyde). The structure of the oligomers was determined by IR and ¹H NMR spectroscopy, and elemental analysis. The oligomers showed good thermal stability. The Fe²⁺ complex of poly(Schiff base), synthesized from MDABT with oxalic aldehyde (PMTOA), was prepared with 13.7% Fe content and found to be a ferromagnet at low temperature.     

New halogen-containing polyimides based on 1,3-bis(3,4-dicarboxyphenyl)-1,1,3,3-tetramethyldisiloxane dianhydride

Previously undescribed halogen-containing polyimides are synthesized via the interaction of 1,3-bis(3,4-dicarboxyphenyl)-1,1,3,3-tetramethyldisiloxane dianhydride with aromatic diamines containing hexafluoroisopropylidene and dichloroethylene groups. The influence of tetramethyldisiloxane, hexafluoroisopropylidene, and dichloroethylene groups incorporated into these polymers on their solubility, heat resistance, thermal stability, and film-forming properties is investigated.