预处理对丝素蛋白膜调控羟基磷灰石晶体生长的影响

以丝素蛋白膜为基质, 在模拟体液中诱导羟基磷灰石晶体在其表面沉积和生长. 利用XRD, SEM, HRTEM, AFM和FTIR等表征手段研究了不同预处理方法对羟基磷灰石晶体的形成及其微观形貌的影响. 结果表明, 丝素膜可有效地诱导羟基磷灰石晶体在其表面沉积和生长; 较长的矿化时间有利于形成较多结晶度良好的HAP晶体; 而不同预处理方法对丝素膜的表面结构产生了不同影响, 进而调制在其表面沉积的羟基磷灰石的形貌和生长方向. 同时对丝素蛋白膜调控羟基磷灰石晶体生长的机制进行了必要的探讨.     

聚乙二醇-b-聚乳酸的合成及其电纺形成超细纤维研究

为了提高聚乳酸的亲水性,以辛酸亚锡为催化剂、聚乙二醇单甲醚(mPEG)为大分子引发剂进行丙交酯(LLA)开环聚合,合成聚乙二醇-b-聚乳酸两嵌段共聚物(PELA).以红外光谱1、H核磁共振谱、接触角测试、差热扫描量热分析等方法对PELA的结构及性能进行表征.结果表明,通过调控mPEG与LLA的投料比可以控制PELA的相对分子质量,而随着mPEG组分含量或链长增加,共聚物亲水性增强,但其Tg、Tcc、Tm有所降低.由普通电纺制备PELA超细纤维,并分别由乳液电纺和同轴电纺得到以水溶性聚氧化乙烯(PEO)为芯、PELA为壳的芯/壳结构复合超细纤维(E-PEO/PELA和C-PEO/PELA).扫描电镜和透射电镜结果表明,PELA、E-PEO/PELA和C-PEO/PELA超细纤维形貌良好.随着PELA中mPEG含量的增加,电纺PELA纤维膜的吸水率增强,而由乳液电纺和同轴电纺制备的PEO/PELA芯/壳结构超细纤维膜,亲水性均好于PELA超细纤维膜.     

纳米羟基磷灰石/丝素蛋白复合支架材料的降解特性及生物相容性研究

应用共混法制备了纳米羟基磷灰石/丝素蛋白复合支架材料, 通过体外降解和细胞培养实验研究了复合支架材料的降解特性和生物相容性. 体外降解实验结果显示, 复合支架材料具有稳定的降解能力; 在降解过程中, 羟基磷灰石由于与降解液发生钙、磷等离子的交换, 使其结晶得到了进一步生长和完善. 利用细胞计数法、四甲基偶氮唑盐(MTT)比色法和碱性磷酸酶(ALP)活性测定等分析了复合支架材料的生物相容性, 结果表明, MG63细胞在复合支架材料上具有良好的粘附、增殖能力, 并可引起早期的骨分化. 因此, 纳米羟基磷灰石/丝素蛋白复合支架作为骨组织工程的支架材料具有良好的应用前景.     

静电纺丝素/胶原/聚合物复合纤维的制备及其力学性能的研究

目前,将天然高分子蛋白和聚合物共混利用静电纺丝法制作各种组织工程支架材料倍受关注。基于这种研究背景,在本文中利用静电纺丝技术,制备了丝素(SF)/胶原(COL)/聚左旋乳酸(PLLA)和SF/COL/聚左旋乳酸-己内酯(PLCL)两种共混复合纤维膜,通过扫描电镜(SEM)对纤维形态结构分析,发现复合纤维形貌良好,直径较为均一。同时改变纺丝液中高分子蛋白的比例,复合纤维的直径也随之减小。此外,对复合纤维进行了力学性能测试,发现随着聚合物含量的增加,复合纤维膜的力学性能得以改善,SF/COL/PLCL组复合纤维的拉伸性能明显优于SF/COL/PLLA组。     

核-壳结构壳聚糖/聚乙烯醇-聚碳酸亚丙酯超细纤维的制备

利用同轴电纺丝技术制备出具有核-壳结构的壳聚糖/聚乙烯醇-聚碳酸亚丙酯电纺丝纤维,考察了溶剂复配对成纤的影响,采用扫描电镜和透射电镜对纤维的形貌、结构、直径分布等进行了探索,并在优化的工艺条件下,将羟基磷灰石负载在内层结构中.研究表明,采用氯仿/N,N-二甲基甲酰胺(1/1)复配溶剂可有效避免聚合物溶液在喷丝口处的凝结现象.同单纺纤维相比,核壳结构的纤维直径分布较宽,纤维壳层和核层界限清晰;红外谱图分析证明羟基磷灰石可负载在纤维的核结构中.     

二氧化硅/聚乙烯醇杂化电纺纤维膜的制备与结构形态

用溶胶-凝胶(Sol-Gel)法制备了不同二氧化硅含量的PVA/SiO2杂化纺丝液,将其电纺成纤维膜.XRD结果表明,杂化电纺纤维膜的结晶度较纯PVA电纺纤维膜小;FTIR证实了PVA的羟基与正硅酸乙酯水解后的羟基发生了缩合反应,杂化电纺纤维膜是以网络结构形式相结合的;FESEM表明,PVA/SiO2质量比为4∶1时,纤维光滑,分散比较均匀.随着二氧化硅含量的增加,纤维直径变细,纺锤形珠节结构增多.加入金属盐NaCl和MgCl2后,纤维直径变细,圆形珠节增多.从理论上分析了纤维膜结构形态的形成机理.     

PVA/SiO2-TiO2杂化电纺纤维膜的形态与性能

以正硅酸乙酯(TEOS)、钛酸四丁酯(TBT)和聚乙烯醇(PVA)为原料, 用溶胶凝胶法制备了PVA/(SiO2-TiO2)杂化纺丝液, 将其电纺成纤维膜. 红外光谱结果证实, PVA的羟基与TEOS和TBT水解后的羟基发生了缩合反应, 杂化电纺纤维膜以网络结构形式相结合; X射线衍射分析表明, 杂化电纺纤维膜的结晶度比纯PVA电纺纤维膜小; 扫描电镜表明, 随杂化纤维膜中无机相含量的增加, 纤维的直径不断增加, 纤维出现一定的弯曲和扭曲, 并伴有少量带状结构的纤维; 紫外-可见光谱结果表明, TiO2的引入增加了纤维膜的抗紫外性; TGA热分析结果表明, 杂化纤维膜的耐热性能优于纯PVA电纺纤维膜的; 耐水性和稳定性测试表明, 杂化纤维膜的耐水性和稳定性优于纯PVA和PVA/SiO2电纺纤维膜的.     

电化学沉积制备羟基磷灰石涂层及机理研究

控制电沉积溶液中钙 /磷离子的浓度 ,在钛合金表面直接沉积羟基磷灰石 (HAP)陶瓷涂层 .XRD、SEM实验证实 ,制备的HAP晶粒完整 ,粒度均匀 .热力学计算表明HAP比TCP更易于生成 .文中讨论了羟基磷灰石 (HAP)涂层电沉积的机理 ,指出电沉积是一个二步过程 ,HAP的形成是从溶液中离子到固体的直接过程 ,没有前驱体的生成     

同轴电纺制备刚性多糖纳米纤维膜

将壳聚糖、海藻酸钠或透明质酸配制成水溶液,聚氧化乙烯(PEO)溶解在二甲基甲酰胺(DMF)/H2O 混合溶剂中,以上述两溶液分别作为内、外纺丝液进行同轴电纺制备成纤维膜,进而利用适当溶剂除去 PEO 外壳,得到纯多糖纳米纤维膜.纤维结构通过 TEM、SEM 进行表征.结果表明:同轴电纺可一步制得外壳为 PEO、内核为刚性多糖的核壳纳米纤维,纤维外壳 PEO 组分可以用氯仿萃取除去;与单轴电纺法制得的刚性多糖纤维相比,同轴电纺可以保持最终纤维的结构完整性.     

同轴电纺超细纤维膜构建人工血管材料

以右旋糖酐(DEX)为芯、聚乙二醇-b-聚(L-丙交酯-co-ε-己内酯)(PELCL)为壳,经同轴电纺制备DEX/PELCL超细纤维膜。在该电纺纤维内芯分别负载血管内皮生长因子(VEGF)和血小板衍生生长因子(PDGF-bb),并以此构建双层超细纤维膜人工血管支架。4 w的释放结果表明,VEGF和PDGF-bb均表现出突释现象,含有肝素的VEGF样品释放量有所下降。大鼠腹主动脉移植实验表明,载有VEGF和PDGF-bb的超细纤维膜可以用于构建双层人工血管。     

Electrospun core–sheath fibers for integrating the biocompatibility of silk fibroin and the mechanical properties of PLCL

In the process of preparing core–sheath fibers via coaxial electrospinning, the relative evaporation rates of core and sheath solvents play a key role in the formation of the core–sheath structure of the fiber. Both silk fibroin (SF) and poly(lactide‐co‐ε‐caprolactone) (PLCL) have good biocompatibility and biodegradability. SF has better cell affinity than PLCL, whereas PLCL has higher breaking strength and elongation than SF. In this work, hexafluoroisopropanol (HFIP)‐formic acid (volume ratio 8:2), HFIP and HFIP–dichloromethane (volume ratio 8:2) were used to dissolve PLCL as the core solutions, and HFIP was used to dissolve SF as the sheath solution. Then, core–sheath structured SF/PLCL (C‐SF/PLCL) fibers were prepared by coaxial electrospinning with the core and sheath solutions. Transmission electron microscopy images indicated the existence of the core–shell structure of the fibers, and energy dispersive X‐ray analysis results revealed that the fiber mat with the greatest content of core–shell structure fibers was obtained when the core solvent was HFIP–dichloromethane (volume ratio 8:2). Tensile tests showed that the C‐SF/PLCL fiber mat displayed improved tensile properties, with strength and elongation that were significantly higher than those of the pure SF mat. The C‐SF/PLCL fiber mat was further investigated as a scaffold for culturing EA.hy926 cells, and the results showed that the fiber mat permitted cellular adhesion, proliferation and spreading in a manner similar to that of the pure SF fiber mat. These results indicated that the coaxial electrospun SF/PLCL fiber mat could be considered a promising candidate for tissue engineering scaffolds for blood vessels. Copyright © 2014 John Wiley & Sons, Ltd.     

聚乳酸-乙醇酸/纳米氧化锌复合电纺纤维装载亲疏水药物的控释及体外细胞毒性

利用静电纺丝技术制备了负载亲水性药物阿霉素(DOX)以及疏水性药物喜树碱(CPT)的复合纳米纤维. 先用巯基封端的普朗尼克(F127)修饰纳米氧化锌(FZnO), 再将FZnO负载盐酸阿霉素(DOX@FZnO), 最后将DOX@FZnO与CPT一起纺入聚乳酸-乙醇酸(PLGA)纤维中. 体外药物释放结果表明, 复合纳米纤维能够减小亲水性药物的突释, 减缓药物释放速率, 延长药物释放时间. 体外细胞活性结果表明, 双载药复合纤维比单载药复合纤维具有更强的细胞毒性, 能够有效抑制癌细胞生长.     

含骨脱细胞基质电纺纤维的成骨性能

通过脱细胞技术制备了猪骨脱细胞基质(DBM), 用胃蛋白酶消化DBM使其变为可溶形式, 采用静电纺丝技术制备了含有DBM的左旋聚乳酸(PLLA)电纺纤维(PLLA/DBM), 并对PLLA/DBM的形貌、 亲水性、 细胞相容性、 成骨性能和体外矿化能力进行评价. 研究结果表明, 脱细胞处理能够有效去除骨组织中的细胞成分, 使DNA含量显著下降. DBM经胃蛋白酶处理后溶于六氟异丙醇(HFIP), 可进行静电纺丝, 制备的PLLA/DBM[m(PLLA)∶m(DBM)=10∶0, 9∶1, 7∶3, 5∶5]电纺纤维具有良好的亲水性, 且无细胞毒性, 对骨髓间充质干细胞的黏附及成骨分化有明显的诱导促进作用, 体外生物矿化效果优良.     

Photocatalytic activities of poly(methyl methacrylate)/titanium dioxide nanofiber mat

This study aimed to evaluate the photocatalytic activities of poly(methyl methacrylate) (PMMA)/titanium dioxide (TiO₂) nanofiber mat. TiO₂ nanoparticles in crystal phase were first prepared by sol-gel process and then PMMA/TiO₂ nanofiber mat was prepared through electrospinning. The composite (PMMA/TiO₂) nanofiber mat was compared with that of pure PMMA nanofiber mat through performing FTIR and UV-Vis spectroscopy, scanning electron microscopy, thermogravimetric analysis, weight loss and water contact angle measurements. The photocatalytic activity of PMMA/TiO₂ nanofiber mat was evaluated by investigating both the photocatalytic decomposition of a model dye, methylene blue, and photocatalytic degradation of the composite nanofiber mat in the ambient air under ultraviolet light irradiation.     

Porous composite scaffolds of hydroxyapatite/silk fibroin via two‐step method

A two‐step method was used to fabricate the hydroxyapatite (HAP)/silk fibroin (SF) scaffolds, i.e. the nano‐sized HAP/SF composite powders were prepared by co‐precipitation, which were then blended with SF solution to fabricate the HAP/SF composite scaffolds. The obtained scaffolds showed a 3D porous structure. The porosity was higher than 90% with the average macropore size of 214.2 µm. Moreover, the nano‐sized HAP/SF composite powders were uniformly dispersed in the silk fibroin matrix, which provided the scaffolds enhanced compressive properties. The cell culture assay showed that the scaffolds fabricated by the two‐step method could improve the cell proliferation and osteogenic differentiation when compared with those prepared by the conventional one‐step blending method. The results suggested that the two‐step method could promote the uniform dispersion of HAP in the SF matrix and efficient combination between the HAP and the matrix, which may provide a potential application in the composite scaffold preparation for tissue engineering. Copyright © 2009 John Wiley & Sons, Ltd.     

Solution‐blown nylon 6–chitosan core–shell nanofiber for highly efficient affinity adsorption

A facile spinning‐based strategy was developed to fabricate chitosan (CS) surface nanofiber‐based affinity membranes for protein adsorption. The core–shell nanofiber mat of nylon 6–CS was prepared via coaxial solution blowing process. The nanofibers have a diameter range of 60–300 nm. The core–shell structure was confirmed by transmission electron microscopy, and CS was observed as a thin layer that uniformly adhered to the core. The dye ligand of cibacron blue F3GA (CB F3GA) was further covalently immobilized on the nanofibers with a content of 425 µmol/g. The pristine and CB F3GA‐attached mats were studied in protein adsorption. High bovine serum albumin adsorption capacities of 91.9 and 219.6 mg/g were obtained for pristine and CB F3GA‐attached mats, respectively. Given its properties of high flux rate and low pressure drop, CB F3GA‐attached nylon 6–CS nanofiber mat meets the requirements of highly effective affinity membrane chromatography. Copyright © 2016 John Wiley & Sons, Ltd.     

聚(丙交酯-co-乙交酯)/β-磷酸三钙复合物的电纺研究

对生物可吸收聚(丙交酯-co-乙交酯)(poly(lactide-co-glycolide),PLGA)与β-磷酸三钙(-βTCP)复合物体系进行了电纺.研究了PLGA的浓度,-βTCP与PLGA比例,加料速度,电压,喷头与接收体之间的距离等因素对电纺过程的影响,制备出纳米纤维膜,并用扫描电镜(SEM)等对纤维膜进行表征.结果表明,电纺溶液浓度越高,或者加料速度越快,纳米纤维的直径越粗.力学实验显示,复合物中-βTCP的含量增加使纳米纤维膜的拉伸强度和杨氏模量下降.     

Fabrication and characterization of polycrystalline WO3 nanofibers and their application for ammonia sensing

We describe the fabrication and characterization of tungsten oxide nanofibers using the electrospinning technique and sol-gel chemistry. Tungsten isopropoxide sol-gel precursor was incorporated into poly(vinyl acetate)(PVAc)/DMF solutions and electrospun to form composite nanofibers. The as-spun composite nanofibers were subsequently calcinated to obtain pure tungsten oxide nanofibers with controllable diameters of around 100 nm. SEM and TEM were utilized to investigate the structure and morphology of tungsten oxide nanofibers before and after calcination. The relationship between solution concentration and ceramic nanofiber morphology has been studied. A synchrotron-based in situ XRD method was employed to study the dynamic structure evolution of the tungsten oxide nanofibers during the calcination process. It has been shown that the as-prepared tungsten oxide ceramic nanofibers have a quick response to ammonia with various concentrations, suggesting potential applications of the electrospun tungsten oxide nanofibers as a sensor material for gas detection.     

浸润性可调的导电聚苯胺/聚丙烯腈同轴纳米纤维

聚苯胺(PANI)因其具有可调的导电性、优异的化学稳定性、简单的制备方法等特点, 在化学电源、抗静电涂层、电磁屏蔽材料、抗腐蚀、传感器等领域具有广泛的应用前景[^1~4]. 由于聚苯胺的刚性分子链使得聚苯胺几乎不溶不熔, 难以加工应用, 因此, 将导电聚合物直接制成纳米纤维一直是合成纤维界所希望的目标之一. 此外, 由于材料尺度的减小, 使纳米材料的表面与界面性质,尤其是表面浸润性变得更为突出.浸润性是固体表面的重要特征之一, 它主要由表面的化学组成和微观结构共同决定^[5,6]. 可调的浸润性在超疏水材料、药物传输、仿生材料和微流体等领域具有重要的应用价值^[7~10] , 引起人们广泛关注.     

Characterization of poly(methyl methacrylate) nanofiber mats by electrospinning process

In this study, the aim is to describe the influence of electrospinning parameters on the morphology, the water wetting property and dye adsorption property of poly(methyl methacrylate) nanofiber mats. Specifically, the effects of solution concentration, solvent type, applied voltage, distance between the electrodes and particulate reinforcement on the diameter and shape of the nanofibers were investigated. All poly(methyl methacrylate) nanofiber mats contained beaded nanofiber structures. With increasing the polymer solution concentration, the average fiber diameter also increased. Poly(methyl methacrylate) nanofiber mat electrospun from dimethylformamide solution resulted in thicker fibers when compared with the mat electrospun from acetone solution. Increasing the electric potential difference between the collector and the syringe tip did not increase the average fiber diameter. Besides increasing the distance between the electrodes resulted in a decrease in the average fiber diameter. When compared with PMMA nanofiber mat, thicker fibers were obtained with silica nanoparticles reinforced nanofiber mat. According to the water contact angle measurements, all poly(methyl methacrylate) nanofiber mats revealed hydrophobic surface property. PMMA nanofiber mat with the highest water contact angle gave rise to the highest dye adsorption capacity.