用离子交换法从工业废液中回收钼

本文研究了用一种新型的离子交换树脂从两种工业度液中回收钼的方法。实验证明:树脂从这两种废液中能很好地吸附钼,吸附速度较快,钼饱和容量较高,达700mg/g干树脂以上。同时,用5.6％氨水进行解吸,钼的解吸性能较好,合格解吸液中钼浓度较高,达90～100g/L以上,该解吸液可直接用于酸化沉淀仲钼酸铵晶体。     

转型TP207树脂从低浓度稀土溶液中富集稀土的研究

为实现从低浓度稀土溶液中高效富集稀土,通过动态吸附-解吸试验,研究了转型TP207树脂吸附稀土的规律。系统考察了离子交换线速度、吸附液体积、初始p H值、铝离子对树脂吸附稀土容量的影响,以及解吸液体积对稀土解吸率的影响。结果表明：在稀土浓度为1.65g·L^-1,离子交换线速度为3 cm·min^-1,吸附液体积为7.50 L,初始p H值为3.46的条件下,TP207树脂对稀土吸附量Q_n1=0.18 g·g^-1;稀土溶液中铝和稀土存在竞争吸附,当Al³⁺浓度为0.35 g·L^-1时,TP207树脂对稀土吸附量Q_n2降为0.11 g·g^-1;采用5%的稀HCl对饱和树脂进行解吸,在解吸液体积为0.525 L时,稀土解吸率可达99.45%;树脂吸附稀土过程属于阳离子交换反应,符合Langmuir等温吸附模型,为单分子层吸附,树脂中C=O的O原子和C-N的N原子均参与配位反应。     

离子交换法去除有机二胺吸收剂PA-A中SO42-的工艺研究

采用单因素实验法,考察了3种树脂对有机二胺吸收剂PA-A水溶液中SO42-的动态吸附-解吸性能,优化了树脂动态吸附-再生工艺.结果表明,D296型树脂具有良好的吸附选择性和较高的吸附容量;当流速为8.08BV/h、高径比为5.64、初始SO42-浓度为96.94g/L时,D296型树脂对PA-A水溶液中的SO42-动态饱和吸附量可达430.06mg/g干树脂;采用4％ NaOH水溶液在4.04BV/h的流速下对吸附饱和的树脂进行洗脱,再生率可达95％左右;树脂重复使用10次后其吸附-解吸性能基本不变.     

吸附树脂对紫背天葵的水溶性色素精制研究

研究吸附树脂吸附精制紫背天葵红色素的方法和工艺。以吸附量、解吸量为指标,在pH=7时吸附,确定出S-8极性树脂和盐酸-乙醇溶液为最佳吸附剂和解吸剂。正交动态吸附和解吸实验结果表明,当原花液浓度3g/L,吸附流速3ml/min,树脂床层径高比1:1时,树脂对色素的吸附量最大;以盐酸-乙醇为解吸剂,解吸液用量30ml/g,解吸流速是1/5BV。经树脂吸附精制后的色素色价是未精制色素的3.74倍。     

大孔阳离子交换树脂对奈替米星的吸附研究

通过正交实验合成了9种大孔弱酸性阳离子交换树脂,筛选出具有最大动态饱和吸附量的FB-1树脂.采用红外光谱和热重分析的方法对其表征,并研究其对奈替米星的吸附及解吸性能,结果表明:该树脂对奈替米星的吸附符合Langrnuir吸附:用氨水做洗脱剂,0.3mol/L和0.4mol/L的氨水解吸率均达95%以上.FB-1与HD-2树脂比较:动态吸附量FB-1为398.0mg/mL湿树脂、HD-2为232.1mg/mL湿树脂;0.3mol/L氨水解吸,前者解吸率较后者高约15%.     

后交联St-DVB吸附树脂对水中低浓度高水溶性有机物的吸附、解吸与回收研究

分别测定后交联苯乙烯-二乙烯基苯(St-DVB)大孔吸附树脂XDA对于浓度在500～1000mg/L且能与水完全互溶的几种低分子含氧有机物的静态和动态吸附性能,采用蒸汽解吸与冰水冷凝精馏一体化技术,探索树脂吸附能力与有机物分子疏水值之间的相关性,以及采用该工艺从含有高价值高水溶性有机污染物废水中分离回收污染物资源的可能性。结果显示,该树脂对浓度500～5000mg/L的8种低级醇、醛和丙酮等均具有一定的吸附能力,其吸附能力与吸附质分子的疏水值呈正相关性,对疏水值较高的丙酮和四氢呋喃的吸附能力最强;树脂吸附饱和后采用蒸汽解吸法可达98%的解吸率,解吸液浓度较吸附原液溶质浓度提高了30～40倍,采用冰水冷凝法精馏工艺前段浓解吸液,回收率达70%～80%。     

D406螯合树脂对硫酸锌溶液中氟的吸附和解吸性能及动力学研究

研究了D406螯合树脂对硫酸锌溶液中氟的吸附和解吸性能,考察了影响氟吸附和解吸的因素以及该树脂吸附和解吸氟的动力学参数。结果表明,在25℃、pH=2、硫酸锌浓度为1.50mol/L、氟离子浓度为200mg/L条件下,D406螯合树脂对氟的吸附量为5.55mg/g。D406螯合树脂对氟的吸附符合Freundlich吸附模型。吸附和解吸的动力学符合Boyd液膜扩散方程,吸附反应活化能Ea=12.14kJ/mol,解吸反应活化能Ea=19.54kJ/mol。     

新型酰乙基葡甲胺树脂的合成及吸硼性能

采用一步法, 用氯乙酰化聚苯乙烯树脂(PS-Acyl-Cl)与葡甲胺反应制得一种同时含有α-酰乙基胺和邻羟基双官能团的新型酰乙基葡甲胺树脂, 考察了溶液pH值、 温度、 初始浓度和吸附时间对酰乙基葡甲胺树脂吸附硼的影响. 结果表明, 在实验浓度范围内, 该树脂对硼的吸附符合Langmuir方程, 最大吸附量约为28.1 mg/g干树脂, 优于氯甲基树脂制得的硼特效树脂. 表明α-酰乙基胺和邻羟基双官能团对硼有双重或协同吸附作用. 该树脂在pH=6.0时对硼的吸附量最大; 温度对树脂吸附的影响不大; 树脂解吸率大于96%; 树脂重复使用5次后吸附量基本不变. 动力学研究结果表明, 吸附过程为液膜扩散控制过程.     

绿茶对水溶液中Pb2+和Cd2+吸附性能初步研究

研究了绿茶对溶液中Pb2 和Cd2 离子的吸附和解吸性质。考察了pH、温度、吸附时间对绿茶吸附性能的影响,得到吸附动力学曲线和吸附等温线。结果表明,茶叶在pH为4~6的弱酸性范围内对两种金属离子的吸附效果最佳,在30℃时,茶叶对Pb2 和Cd2 的饱和吸附量分别为46.66 mg/g和33.29mg/g,吸附符合Langmuir吸附等温方程,并对吸附机理进行了初步的探讨。对解吸条件研究发现,用0.1 mol/L HCl和EDTA作为解吸剂,对Pb2 和Cd2 的解吸效果较好,解吸率达80%以上,可有效回收重金属Pb2 和Cd2 。     

新型硅胶-聚合胺树脂从氯化钴电解液中深度净化除铜

SP-C是一种新型硅胶-聚合胺复合材料树脂,对铜具有较好的选择吸附性能.本文研究了该树脂在模拟氯化钴电解液中深度净化除铜工艺.在Co2 ～80g/L,Cu2 0.5g/L～2.0g/L、pH2～4、温度20℃～60℃的氯化钴电解液中,考察了该树脂对铜的吸附性能.结果表明,随料液pH增大以及温度升高,铜的交换容量增大:料液Cu2 浓度对交换容量影响较小;最佳吸附条件为:料液pH 4、接触时间30min,温度60℃.对比研究了盐酸、硫酸两种解析液,硫酸显示出更好的解析效果,最佳解析条件为H2SO42mol/L、解析接触时间40min.最佳工艺条件下,每毫升湿树脂对铜的工作交换容量及饱和交换容量分别为0.439mol和0.508mol,铜的解析液峰值浓度为28g/L.     

钼酸根阴离子印迹陶瓷膜的制备与吸附性能

以三氧化二铝陶瓷膜为载体,以钼酸根阴离子为模板离子,1-乙烯基咪唑为功能单体,1,6-二溴己烷为交联剂,采用表面印迹和接枝聚合方法制备了能选择性吸附Mo(Ⅵ)的新型印迹陶瓷膜(IIP-PVI/CM).采用红外光谱、X射线光电子能谱、热重分析及扫描电子显微镜等方法对陶瓷膜进行结构表征.研究了pH值对吸附性能的影响,当pH值范围为2~4时,IIP-PVI/CM具有良好吸附能力;动力学和热力学结果表明,IIP-PVI/CM对Mo(Ⅵ)的吸附符合准二级动力学模型和Langmuir吸附模型;当pH=4.0和温度为30℃时,IIP-PVI/CM对Mo(Ⅵ)具有良好选择性,Mo(Ⅵ)对W(Ⅵ)的选择性系数高达7.48;动态吸附结果表明,IIP-PVI/CM对W(Ⅵ)和Mo(Ⅵ)的吸附饱和时间分别为24和47 min,饱和吸附量分别为0.163和0.672 mmol/100 g,动态吸附时IIP-PVI/CM亦具有良好选择性;经9次吸附与解吸后,IIP-PVI/CM对Mo(Ⅵ)吸附容量仍可达到初始值的92%,再生和循环使用性能良好.     

Removal, preconcentration and determination of Mo(VI) from water and wastewater samples using maghemite nanoparticles

Removal and recovery of Mo(VI) from aqueous solutions were investigated using maghemite (γ-Fe₂O₃) nanoparticles. Combination of nanoparticle adsorption and magnetic separation was used to the removal and recovery of Mo(VI) from water and wastewater solutions. The nanoscale maghemite with mean diameter of 50 nm was synthesized by reduction coprecipitation method followed by aeration oxidation. Various factors influencing the adsorption of Mo(VI), e.g. pH, temperature, initial concentration, and coexisting common ions were studied. Adsorption reached equilibrium within <10 min and was independent of initial concentration of Mo(VI). Studies were performed at different pH values to find out the pH at which maximum adsorption occurred. The maximum adsorption occurred at pHs between 4.0 and 6.0. The Langmuir adsorption capacity (q_max) was found to be 33.4 mg Mo(VI)/g of the adsorbent. The results showed that nanoparticle (γ-Fe₂O₃) is suitable for the removal of Mo(VI), as molybdate, from water and wastewater samples. The adsorbed Mo(VI) was then desorbed and determined spectrophotometrically using bromopyrogallol red as a complexation reagent. This allows the determination of Mo(VI) in the range 1.0–86.0 ng mL⁻¹.     

介孔二氧化硅纳米球对水中Mo(VI)的吸附研究

本研究制备了介孔二氧化硅纳米球(MSN),并用之吸附脱除水中的Mo(VI)。应用扫描电镜、介孔分析仪、红外光谱等对MSN进行了表征。考察了pH、吸附时间、MSN投加量和温度对水中Mo(VI)脱除率的影响,并在单因素试验基础上通过正交试验法确定了Mo(VI)的最佳脱除条件：pH=3,MSN投加量为 8.5g/L,吸附时间为36h。在优化吸附试验条件下MSN对加标水中Mo(VI)的脱除率为93.6% ~ 97.3%。     

Study on Adsorption Properties of Cinchonine Loaded Resin to Mo and V by ICP-AES

ABSTRACT

A new adsorbent cinchoine loaded resin (CCR) was prepared with cinchonine loaded on cation exchange resin. ICP-AES was used to study CCR's adsorption properties to Mo(VI) and V(VI). It was found that the adsorption rate was more than 90% in pH (3～6); and 0.6 mol/L HCl could elute Mo and V quantitatively from CCR. The static adsorption capacities are 8.3 mg/g and 9.9 mg/g for Mo and V, respectively. The interference of some ions were also investigated. The proposed method has been applied to determine Mo and V in standard reference samples with s8543172 results.     

钙蒙脱土吸附镧的影响因素及其应用

以钙基蒙脱土(Ca-MMT)为载体,研究其对镧(La)的吸附。 采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和元素mapping分析、傅里叶红外光谱(FT-IR)、BET、X射线荧光光谱分析(XRF)对其晶型结构、表面形态、比表面积、化学结构进行表征,考察了La的初始浓度、pH值、温度对Ca-MMT吸附镧性能的影响,考察了载镧钙基蒙脱土(Ca-MMT@La)的除磷效果。 结果表明:Ca-MMT投入量为10 g/L时,Ca-MMT的平衡吸附量随镧的初始浓度增加而增大,最大吸附量为49.62 mg/g;随着pH值增大,吸附能力增强,pH=6时为最佳pH吸附镧条件,吸附量为38.36 mg/g;随温度的升高,其吸附量先下降再上升,20 ℃吸附能力最大,吸附量为41.23 mg/g。 Langmuir等温吸附方程推断其吸附属于单分子层吸附。 Ca-MMT不具有吸附磷效果,而Ca-MMT@La对磷酸根有很强的吸附能力,吸附量为7.24 mg/g,除磷率为72.41%,其除磷率随含镧量增大而增大。     

Phenol removal from aqueous solution by carbon xerogel

Carbon xerogel (CX) was used for phenol adsorption from aqueous solution. CX was synthesized by sol?Cgel polycondensation of resorcinol with formaldehyde using sodium carbonate (Na₂CO₃) as catalyst. Then, it was dried by convective drying technique and pyrolyzed under inert atmosphere. Phenol adsorption kinetics was very fast, what was attributed to the presence of open pore structure. The kinetic studies showed that the adsorption process could be fitted to a pseudo-second-order model and the particle diffusion process is the rate-limiting step of the adsorption. The phenol removal was maximum and unaffected by pH changes when the initial pH of the phenol solution was in the range of 3?C8. The optimum adsorbent dose obtained for phenol adsorption onto CX was 0.075?g/50?cm³ solution. The Langmuir model described the adsorption process better than the Freundlich isotherm model and the monolayer adsorption capacity is 32?mg?g^?1. Among the desorbing solutions used in this study, the most efficient desorbent was EtOH (100?%) which released about 87?% of phenol bound with the CX.     

纳米TiO2分离富集Mo(Ⅵ)和Re(Ⅶ)

本文研究了纳米TiO2吸附剂对Mo(VI)、Re(VII)的吸附行为,考察了溶液的pH值、吸附时间、温度等因素对吸附的影响。结果表明：纳米TiO2对Mo(VI)的吸附在pH 1～8条件下,吸附率超过99%,2 mL 0.05mol/L NaOH溶液可将吸附的Mo(VI)离子完全洗脱,解吸率能达到97%。在pH 1～10范围内,纳米TiO2不吸附Re(VII), 从而达到Mo(VI)、Re(VII)分离。在2℃～50℃温度范围内,Mo(VI)的吸附过程符合Langmiur等温式,纳米TiO2对Mo(VI)的最大吸附容量从11.51mg g-1增加到14.19 mg g-1;纳米TiO2分离钼后,溶液剩余的铼,用活性炭吸附,在pH1～10范围内, Re(VII)的吸附率可达99%,用浓氨水进行洗脱,洗脱率可达96%;吸附过程可用准二级反应动力学模型描述,是以化学吸附为控制步骤的吸附过程;吸附等温线与Freundlich模型有较好的拟合。     

焙烧层状氢氧化镁铝对水中氟离子的吸附性能

研究了焙烧层状氢氧化镁铝(CLDH)对水中氟离子的吸附性能,考察了焙烧温度、吸附时间、吸附剂用量、溶液pH值等条件对吸附的影响.发现在较宽的pH(5.5～9.5)值范围内,CLDH对水中氟离子具有良好的吸附能力,室温下0.2gCLDH可将50mL浓度为15mg/L氟离子溶液处理为符合含氟标准的饮用水.吸附平衡符合Langmuir方程,在60min内达到饱和吸附,室温下饱和吸附量为22.64 mg/g.吸附饱和后的CLDH焙烧再生,循环使用5次后饱和吸附量为10.37 mg/g.     

Preparative separation of lithospermic acid B from Salvia miltiorrhiza by polyamide resin and preparative high-performance liquid chromatography

Adsorption on polyamide resin was investigated as a means of separating lithospermic acid B (LAB) from a crude extract of the roots of the traditional Chinese medicine Salvia miltiorrhiza Bunge ("Danshen"). Variables affecting adsorption capacity (solution pH, contact time on resin, initial LAB concentration) were studied. Adsorption was strongly dependent upon the initial concentration of LAB and pH. In all conditions, the polyamide resin gave optimal adsorption of LAB at an initial concentration of 2.66 mg/mL and pH <3.0. The adsorption isotherm correlated well with the Langmuir-type adsorption isotherm. Maximal adsorption capacity was calculated to be 380 mg/g at pH 2.0 and 25°C. LAB purity of 85.30% could be obtained by polyamide resin adsorption followed by elution with 70% ethanol solution, and the recovery was 87.1%. After preparative HPLC, the maximum HPLC purity obtained was 99.28% with a recovery of 75.2%. This method provides an efficient and low-cost method for LAB purification for industrial applications.     

H_6P_2Mo_(18)O_(62)/Zn(BDC)(Bipy)_(0.5)复合材料的合成、表征及对亚甲基蓝的吸附

在溶剂热条件下,以H6P2Mo18O62、对苯二甲酸(H2BDC)、4,4'-联吡啶(Bipy)和硝酸锌为原料构筑了1个三维金属有机骨架复合材料H_6P_2Mo_(18)O_(62)/Zn(BDC)(Bipy)_(0.5),并采用红外光谱(IR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、热重分析(TG)、N2吸附-脱附等手段对产物进行了表征.同时,研究了产物对水溶液中亚甲基蓝(MB)的吸附性能,并探讨了MB初始p H值、初始浓度和温度对吸附量的影响.结果表明,产物的等温吸附模型符合Langmuir等温吸附模型,动力学符合拟二级动力学.H_6P_2Mo_(18)O_(62)/Zn(BDC)(Bipy)_(0.5)对亚甲基蓝的吸附是自发和放热的,此外,产物对甲基紫、罗丹明B、孔雀石绿等阳离子染料也具有良好的吸附性能.