被动隔振体非线性振动的能量迭代解法

研究了由基础振动激励、弹性材料隔离的被动隔振体的强非线性动力响应。用变形的三次多项式函数表征隔振材料的非线性刚度特性,建立了被动隔振体的非线性动力学方程,得到有阻尼受迫振动Duffing方程。将求解强非线性自治系统的能量迭代方法加以改进,推广应用到强非线性非自治系统,求出周期响应的近似解析解表达式,以及幅频关系、相频关系和隔振系数的近似表达式。算例中应用本方法与Runge-Kutta方法进行了对照,结果表明求解精度较高。本文利用计算机进行了辅助推导。     

几何非线性摩擦阻尼隔振系统动力学行为研究

非线性隔振系统由于具有较线性系统更优的隔振性能,因此在工程中应用广泛.本文通过配置与被隔振对象的运动方向相垂直的库伦摩擦阻尼器,构建了几何非线性摩擦阻尼模型.由于引入了几何非线性,因此其摩擦力与位移正相关,这与传统与位移无关摩擦力模型有显著不同.首先,建立了具有几何非线性摩擦阻尼的数学模型以及隔振系统的受迫振动方程;然后,使用谐波平衡法求解了动力学方程,并使用数值仿真方法验证了谐波平衡法求解的准确性;最后,研究了几何非线性摩擦阻尼隔振器的绝对位移传递率和相对位移传递率.研究结果表明,在库伦摩擦阻尼选择适当,非线性摩擦阻尼系统可以在保持高频振动衰减效果的前提下,显著降低系统共振峰,其性能优于传统的恒定摩擦阻尼隔振模型.同时,几何非线性摩擦阻尼系统能够避免传统摩擦阻尼系统中的“锁定”现象,从传递率角度来说,不利于共振峰控制;但从激励环境改变引发隔振系统失效的角度来看,几何非线性摩擦阻尼系统可以拓宽系统对激励幅值的适应范围,避免隔振系统失效.本文的研究结果对此类隔振系统的设计和摩擦阻尼参数的选择具有通用的指导意义.      

一类分段光滑隔振系统的非线性动力学设计方法

分段光滑隔振系统是一类具备分段刚度或阻尼的非线性动力学系统,在振动控制领域中具有广泛代表性,诸如限位隔振系统、分级汽车悬挂等. 分段光滑的刚度或阻尼特性能够实现隔振系统的特定动力学性能及提升隔振性能,如抑制共振响应、提升共振区隔振性能等,但是亦会给隔振系统的动力学行为带来诸多不利影响. 以分段双线性分段光滑隔振系统为理论模型,系统研究了摒除不利于隔振的非线性动力学现象设计方法,包括幅值跳跃、周期运动的倍周期分岔等. 首先,利用平均法与奇异性理论给出了主共振频响曲线拓扑特征的完整拼图. 研究结果表明,参数空间分为4 个区域,其中2 个区域存在幅值跳跃,而其产生跳跃原因分别由鞍结分岔与擦边分岔所导致;基于此提出避免主共振跳跃的设计方法. 其次,建立了隔振有效区内周期运动的庞加莱映射,通过特征值分析给出了避免倍周期分岔发生的条件,证实增大阻尼可以抑制倍周期分岔的发生. 最后通过数值仿真分析了噪声对多稳态运动的影响. 研究结果发现在噪声影响下,分段光滑隔振系统的响应会在不同稳态间跃迁,非常不利于隔振. 因此,在完成跳跃与倍周期分岔的防治设计后,应采用数值仿真校验系统是否存在多稳态运动.      

磁致伸缩主被动隔振装置中的磁机耦合效应研究

磁致伸缩材料和柔顺位移放大机构组成的主动驱动装置具有精度高、驱动力大等特点.将其与被动隔振装置并联,形成主被动隔振装置,可以弥补纯被动隔振在低频和微幅扰动工况下的不足.本文针对这类磁致伸缩主被动隔振装置进行磁机耦合效应研究.基于Jiles-Atherton模型,分析了磁致伸缩材料所受应力对有效磁场、磁化强度、磁致伸缩系数和材料杨氏模量的影响,表征了材料磁机耦合效应.在此基础上,建立了主被动隔振装置的动力学模型,分析了主动驱动装置与被动隔振装置间的耦合作用.在耦合作用影响下,若被动隔振装置刚度不同,即使输入磁场相同,驱动器产生的驱动位移和驱动力也不相同.磁致伸缩材料的变刚度效应使隔振装置整体等效刚度不再为定值,从而影响被动隔振效果.本文提出了通过柔顺机构参数设计减小前述两种耦合影响的方法.数值仿真结果表明,磁致伸缩主被动隔振装置在低于、接近和高于谐振频率三类扰动下,都能达到比被动隔振更好的振动抑制效果.此外,仿真结果验证了考虑磁机耦合效应的数值模型具有更高精度.      

确定非线性隔振装置参数的一种方案

对单自由度刚度可调非线性隔振模型进行数学建模仿真和实验，对于待训练的神经网络模型，将数值仿真结果作为学习样本，将实验结果作为检验样本，训练成功的神经网络模型具有较好的内延能力和一定的外推能力，在设定非线性隔振装置要求的隔振效能参数后，可以给出隔振装置对应的刚度和阻尼参数，从而为设计非线性隔振装置提供了一种方案。     

橡胶隔振系统非线性振动参数识别与特性研究

建立单自由度非线性系统基础激励正弦扫描试验的数学模型,并针对多项式非线性阻尼与多项式非线性弹簧并联的橡胶隔振系统求解了数学模型.进而在此框架下通过正弦扫描振动试验,采用共振峰值法识别了橡胶隔振器的非线性阻尼与刚度系数,研究了不同振动量级下小型橡胶隔振器的振动特性.     

惯容器对隔振系统动态性能影响研究

本文设计了一种滚珠丝杠惯容器及ISD隔振系统,通过实验研究了惯性轮的转动惯量对惯容值的影响;同时,分析了滚珠丝杠惯容器的机械动力学特性,推导了ISD隔振系统的振动传递率计算公式,探讨了惯容器对ISD隔振系统动态特性的影响。在电机被动、主动和混合隔振工况下,开展了弹簧阻尼系统和ISD隔振系统的振动性能对比实验,验证了惯容器对振动系统固有频率和减振效果的影响规律。研究结果表明,惯容器可降低振动系统的固有频率,使共振频率向低频移动,共振振幅降低;在共振频率附近,惯容器可抑制共振振幅,惯容值越高,抑制效果越明显;ISD隔振系统在低频的减振效果优于传统的弹簧阻尼系统;随着频率比的增加,ISD隔振系统的传递率趋于稳定值,惯容器会引起高频隔振性能降低。     

一类新型多方向准零刚度隔振平台

本文提出了一种新的多自由度非线性隔振平台．利用一组预压的三角机构和曲面边界同时实现了竖直-旋转多自由度上的负刚度特性,结合正刚度原件,实现竖直-旋转多自由度准零刚度特性．首先,文章基于平面问题建立竖直-旋转两自由度隔振平台的力学模型,确定结构参数与非线性刚度之间的关系．可以看到,通过设计预压弹性元件的结构参数可以同时实现两自由度的准零刚度特性．然后,利用谐波平衡法建立振动响应与频率之间的关系,确定有效的振动带隙的宽度,由此确定结构参数的最优取值．本文提出的隔振平台可以用于大型装备的隔振,也适用于微振动的工况,还可以作为教学的演示实验．     

一类液固混合介质隔振器的动力学特性研究

液固混合介质隔振器基于一种全新的工作机理,具有优良的隔振系统动力学特性.混合介质由一类几乎不可压缩液体和许多可压缩的固体单元混合而成.当振动、冲击发生时, 液体将动压力瞬间传递到所有单元体上,使它们同时参与变形,从而有效隔离振动,大幅度吸收、损耗冲击能量;若设计得当,这类隔振器可同时具有卓越的隔振和缓冲性能.以空心橡胶球作为固体单元体, 分析了该单元体在有限变形情况下的变形规律,分析了隔振器的非线性刚度特性; 采用MTS液压伺服试验系统进行了测试验证,理论分析和试验结果具有较好的一致性. 建立了系统的非线性动力学方程,采用多尺度摄动法获得了系统的频响特性, 发现系统具有软弹簧非线性动力学特性,并在试验中得到了证实; 因为弹性恢复力中存在位移平方项,通过试验和数值仿真进一步验证了系统响应的非对称性.      

STUDY ABUT NONLINEAR FACTOR INFLUENCE ON THE VIBRATION ISOLATION EFFECT OF DAMPER

本文在同时考虑刚度和阻尼非线性的基础上, 研究了非线性因素对隔振器隔振效果的影响;获得了同时考虑立方刚度非线性和椭圆阻尼非线性的非线性系统运动响应和传递率计算公式;讨论了非线性因素对系统运动响应和传递率的影响.     

A state-of-the-art review on low-frequency nonlinear vibration isolation with electromagnetic mechanisms

Vibration isolation is one of the most efficient approaches to protecting host structures from harmful vibrations, especially in aerospace, mechanical, and architectural engineering, etc. Traditional linear vibration isolation is hard to meet the requirements of the loading capacity and isolation band simultaneously, which limits further engineering application, especially in the low-frequency range. In recent twenty years, the nonlinear vibration isolation technology has been widely investigated to broaden the vibration isolation band by exploiting beneficial nonlinearities. One of the most widely studied objects is the “three-spring” configured quasi-zero-stiffness (QZS) vibration isolator, which can realize the negative stiffness and high-static-low-dynamic stiffness (HSLDS) characteristics. The nonlinear vibration isolation with QZS can overcome the drawbacks of the linear one to achieve a better broadband vibration isolation performance. Due to the characteristics of fast response, strong stroke, nonlinearities, easy control, and low-cost, the nonlinear vibration with electromagnetic mechanisms has attracted attention. In this review, we focus on the basic theory, design methodology, nonlinear damping mechanism, and active control of electromagnetic QZS vibration isolators. Furthermore, we provide perspectives for further studies with electromagnetic devices to realize high-efficiency vibration isolation.

     

DYNAMIC CHARACTERISTICS OF VIBRATION ISOLATION SYSTEM WITH CUBIC STIFFNESS AND HYSTERESIS 1)

包含立方刚度和Bouc-Wen 型滞回的隔振系统具有复杂的非线性动力学特性。系统无阻尼响应模型可基于无滞回恢复力建立,利用谐波平衡法和泰勒展开求得近似解析解。系统有阻尼响应模型可利用解析/数值联合方法求解,该方法基于谐波平衡法和Levenberg-Marquardt 迭代算法,对于滞回产生的多值非光滑函数项,先计算时域响应再通过快速傅里叶变换求解谐波项系数。上述方法在含水平绞制梁的非线性隔振系统分析中得到有效应用。分析表明,在Bouc-Wen 型滞回和立方刚度的综合影响下,隔振系统呈现渐软–渐硬特性,滞回阻尼和线性阻尼都可以有效抑制共振,但前者高频隔振效果优于后者。     

Research on linear/nonlinear viscous damping and hysteretic damping in nonlinear vibration isolation systems

A nonlinear vibration isolation system is promising to provide a high-efficient broadband isolation performance. In this paper, a generalized vibration isolation system is established with nonlinear stiffness, nonlinear viscous damping, and Bouc-Wen(BW)hysteretic damping. An approximate analytical analysis is performed based on a harmonic balance method(HBM) and an alternating frequency/time(AFT) domain technique.To evaluate the damping effect, a generalized equivalent damping ratio is defined with the stiffness-varying characteristics. A comprehensive comparison of different kinds of damping is made through numerical simulations. It is found that the damping ratio of the linear damping is related to the stiffness-varying characteristics while the damping ratios of two kinds of nonlinear damping are related to the responding amplitudes. The linear damping, hysteretic damping, and nonlinear viscous damping are suitable for the small-amplitude, medium-amplitude, and large-amplitude conditions, respectively. The hysteretic damping has an extra advantage of broadband isolation.     

介电弹性作动器主动隔振模糊控制试验研究

采用模糊控制策略,开展介电弹性作动器的主动隔振性能试验研究。基于介电弹性材料的Maxwell应力模型建立了作动器的力电耦合模型,分析了作动器的非线性特性;针对隔振系统设计了Mamdani型模糊控制器,建立了控制电压信号与振动响应之间的关系;在此基础上,开展了介电弹性作动器主动隔振试验研究,并与加速度反馈控制进行了对比。试验结果表明,在相同驱动电压的情况下,基于模糊控制策略的主动隔振性能要优于加速度反馈控制,且能够显著降低由于非线性驱动力导致的倍频响应幅值,有助于提高隔振系统的稳定性。     

Effects of anti-symmetric nonlinear viscous damping on the force transmissibility of multi-degree of freedom structures

In the present study, the concept of the output frequency response function is applied to theoretically investigate the force transmissibility of multi-degree of freedom (MDOF) structures with a nonlinear anti-symmetric viscous damping. The results reveal that an anti-symmetric nonlinear viscous damping can significantly reduce the transmissibility over all resonance regions for MDOF structures while it has almost no effect on the transmissibility over non-resonant and isolation regions. The results indicate that the vibration isolators with an anti-symmetric damping characteristic have great potential to overcome the dilemma in the design of linear viscously damped vibration isolators where an increase of the damping level reduces the force transmissibility over resonant region but increases the transmissibility over non-resonant regions.     

Study on the force transmissibility of vibration isolators with geometric nonlinear damping

By a special layout of the damper in a vibration isolation system, the velocity-nth power damping of the damper can be transformed into the velocity-displacement dependent damping in the moving direction due to geometric nonlinearity. This study is mainly concerned with the mechanism of this geometric nonlinear damping and tries to find some guidelines for designing isolators with high performance, regardless of the isolator is passive or active. The model used in this study is an unconstrained two-degree-of-freedom isolation system, which is suitable for investigating vibration isolation in space vehicles. The motion equation is solved by the averaging method to obtain the amplitude–frequency equation. The influence of damping coefficients on the force transmissibility is analyzed. Results show that this kind of damping has some advantages in improving isolation performance at both the resonance and higher frequencies. Meanwhile, it can also degrade the isolation performance if unreasonable parameters are chosen.     

A 6-DOF passive vibration isolator based on Stewart structure with X-shaped legs

By employing the nonlinear stiffness and damping characteristics of a bio-inspired X-shaped structure (XSS) with passive springs and the Stewart platform with six degrees of freedom, a passive 6-DOF vibration isolation platform is designed and experimentally studied for its vibration isolation performance. A three-layer asymmetrical XSS is adopted as legs to construct a passive Stewart platform. Because of the specially designed XSS, the stiffness and damping properties of the system can be adjusted by changing structural parameters and thus it is designable to achieve an excellent performance including excellent stability and high-static-low-dynamic-stiffness isolation effect in all six directions with satisfactory loading capacity in the vertical direction, without any active control. Analytical and extensive experimental analysis of static stiffness and vibration response of the system revealed that (a) the aXSS Stewart platform has very beneficial high static nonlinear stiffness which can provide sufficient loading capacity; (b) the platform can achieve very low dynamic stiffness in each direction without losing loading capacity; (c) both static and dynamic stiffness is adjustable and designable with structure parameters and very easy to implement in a pure passive manner.