浸渍-分解法制备高可见光催化活性的Bi2O3/TiO2纳米管阵列

用浸渍-分解法将Bi₂O₃纳米颗粒沉积在TiO₂纳米管壁上, 制备了Bi₂O₃/TiO₂纳米管阵列. 用电感耦合等离子体发射光谱(ICP-AES)测定了Bi₂O₃/TiO₂ 纳米管阵列的化学组分, 利用X 射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外-可见(UV-Vis)吸收光谱表征了所制备的样品. 通过在可见光下(λ>400 nm)降解甲基橙(MO)水溶液来评价样品的光催化活性. 结果表明, Bi₂O₃纳米颗粒均匀地沉积在TiO₂纳米管中. Bi₂O₃/TiO₂纳米管阵列具有比纯Bi₂O₃膜和N-TiO₂纳米管阵列高得多的可见光催化活性. Bi₂O₃/TiO₂纳米管阵列活性的增强是其强可见光吸收和Bi₂O₃与TiO₂之间形成的异质结的协同作用的结果.     

Preparation and characterization of Zr doped TiO2 nanotube arrays on the titanium sheet and their enhanced photocatalytic activity

This paper described a new method for the preparation of Zr doped TiO₂ nanotube arrays by electrochemical method. TiO₂ nanotube arrays were prepared by anodization with titanium anode and platinum cathode. Afterwards, the formed TiO₂ nanotube arrays and Pt were used as cathode and anode, respectively, for preparation of Zr/TiO₂ nanotube arrays in the electrolyte of 0.1 M Zr(NO₃)₄ with different voltage and post-calcination process. The nanotube arrays were characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV-Vis diffusion reflection spectra (DRS). The photocatalytic activities of these nanotubes were investigated with Rhodamine B as the model pollutant and the results demonstrated that the photocatalytic efficiency of Zr doped TiO₂ nanotubes was much better than that of TiO₂ nanotubes under UV irradiation. Zr/TiO₂ nanotube arrays doped at 7 V and calcined at 600 °C (denoted as TiO₂-7 V-600) achieved the best photocatalytic efficiency and the most optimal doping ratio was 0.047 (Zr/Ti). TiO₂-7 V-600 could be reused for more than 20 times and maintained good photocatalytic activities.     

Photoelectrochemical water splitting and simultaneous photoelectrocatalytic degradation of organic pollutant on highly smooth and ordered TiO2 nanotube arrays

The photoelectrochemical water splitting and simultaneous photoelectrocatalytic degradation of organic pollutant were achieved on TiO₂ nanotube electrodes with double purposes of environmental protection and renewable energy production under illumination of simulated solar light. The TiO₂ nanotube arrays (TiO₂ NTs) were fabricated by a two-step anodization method. The TiO₂ NTs prepared in two-step anodization process (2-step TiO₂ NTs) showed much better surface smoothness and tube orderliness than TiO₂ NTs prepared in one-step anodization process (1-step TiO₂ NTs). In the photoelectrochemical water splitting and simultaneous photoelectrocatalytic decomposition process, the 2-step TiO₂ NTs electrode showed both highest photo-conversion efficiency of 1.25% and effective photodecomposition efficiency with existing of methylene blue (MB) as sacrificial agent and as pollutant target. Those results implied that the highly ordered nanostructures provided direct pathway and uniform electric field distribution for effective charges transfer, as well as superior capabilities of light harvesting.     

自掺杂TiO2纳米管：液相制备及光催化性能

采用水合肼（N₂H₄·H₂O）作为还原剂,在液相环境中制备了自掺杂TiO₂纳米管阵列（NTs）。利用FE-SEM、EDS、XPS、XRD、Raman、UV-Vis/NIR分光光度法以及半导体特性分析系统（Keithley 4200 SCS）分别对样品的形貌,晶体结构,光学特性以及电学性能进行了表征。结果表明：通过这种方法制备的自掺杂TiO₂NTs在带隙中引入了大量的氧空位,创造了氧空位能级,从而提高了样品的电导率,有效提高光生电子-空穴对的产生、分离和传输。此外,由于氧空位的作用,使得TiO₂NTs的带隙变窄,增强了可见光吸收能力,致使样品具有较高的光催化活性,并通过降解甲基橙溶液对样品的光催化活性进行评估。结果显示当光照150min后,自掺杂TiO₂NTs对甲基橙溶液的降解率达73%,并且这种催化剂便于回收和重复使用。     

TiO2纳米管阵列覆盖Si薄膜光催化还原CO2性能的研究

本工作采用CVD法在阳极氧化TiO2纳米管阵列膜表面沉积一层非晶Si膜,通过退火后得到晶化了的Si膜/TiO2纳米管阵列的复合结构,并初步就其光催化还原CO2制备碳氢化合物的活性进行研究。拉曼光谱(Raman)、X射线衍射(XRD)、场发射扫描电镜(FE-SEM)、高分辨透射电子显微镜(TEM)等微结构表征结果表明所制备的TiO2纳米管阵列的厚度为270 nm左右,管直径约为70 nm,管壁厚度约为16 nm。覆盖的Si膜已晶化,其厚度约为300 nm。通过高效液相色谱(HPLC)及总有机碳(TOC)来检测光催化还原液相产物中的甲酸及总有机碳含量,发现负载Si膜后的TiO2纳米管阵列光催化性能有所提高,在装有400cut滤光片氙灯照射2 h下TOC含量从21.2 mg.L-1增长到29.5 mg.L-1,表明Si与TiO2的复合可有效的提高光催化还原CO2的活性,这可能与该异质结结构可增加对光的吸收并且可降低光生空穴-电子对复合有关。光催化循环实验表明所制得的催化剂在循环5次后仍可保持91.6%的催化活性。     

Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite

A C–N-doped TiO₂ nanotube (NT)/carbon nanorod composite is fabricated by chemical vapor deposition (CVD). Carbon nanorods are grown from the TiO₂ NTs, and partly graphitized, while TiO₂ is in the mixture of anatase and rutile. The C–N doping shifts the absorption edge of TiO₂ NTs to the visible light region; the formed carbon nanorods promote the charge carrier transfer from the TiO₂ surface to the electrolyte. Under the simulated solar light irradiation, the C–N-doped TiO₂ NTs show higher photocatalytic activity in the degradation of methyl orange (MO) than the undoped TiO₂ NTs.     

脉冲沉积制备Cu2O/TiO2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO₂纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu₂O纳米颗粒修饰改性TiO₂纳米管阵列,形成Cu₂O/TiO₂ 纳米管异质结复合材料. 利用场发射扫描电镜（FESEM）、场发射透射电镜（FETEM）、X射线衍射（XRD）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）对样品进行表征,重点研究了Cu₂O/TiO₂ 纳米管异质结的光电化学特性和对甲基橙（MO）的可见光催化降解性能. 结果表明,Cu₂O纳米颗粒均匀附着在TiO₂纳米管阵列的管口和中部位置,所制备的Cu₂O/TiO₂ 纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol·L^-1的CuSO₄溶液中制得的Cu₂O/TiO₂纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu₂O纳米颗粒影响光催化活性的机理进行了讨论.     

Degradation of ofloxacin by UVA-LED/TiO<Subscript>2</Subscript> nanotube arrays photocatalytic fuel cells

The degradation of ofloxacin (OFX) at low concentration in aqueous solution by UVA-LED/TiO₂ nanotube arrays photocatalytic fuel cells (UVA-LED/TiO₂ NTs PFCs) was investigated. TiO₂ nanotube arrays (TiO₂ NTs) photoanode prepared by anodization-constituted anatase–rutile bicrystalline framework. The results indicated that the degradation efficiency of OFX by UVA-LED/TiO₂ NTs PFC was significantly enhanced by 14.3% compared with UVA-LED/TiO₂ NTs photocatalysis. The pH affected the degradation efficiency markedly; the highest degradation efficiency (95.0%) and the pseudo-first-order reaction rate constant k value (0.049 min^?1) were achieved in neutral condition (pH 7.0). The degradation efficiency increased with the increasing concentration of dissolved oxygen (DO) in the UVA-LED/TiO₂ NTs PFC. The main reactive species of OFX degradation are positive holes (h⁺) and superoxide ion radicals (O ₂ ^·? ) in a DO sufficient condition. Furthermore, the possible pathways of OFX degradation were proposed.     

Fabrication and photocatalytic activity of high-efficiency visible-light-responsive photocatalyst ZnTe/TiO2 nanotube arrays

A new ZnTe modified TiO₂ nanotube (NT) array catalyst was prepared by pulse potential electrodeposition of ZnTe nanoparticles (NPs) onto TiO₂ NT arrays, and its application for photocatalytic degradation of anthracene-9-carboxylic acid (9-AnCOOH) was investigated. The even distribution of ZnTe NPs was well-proportionately grown on the top surface of the TiO₂ NT while without clogging the tube entrances. Compared with the unmodified TiO₂ NT, the ZnTe modified TiO₂ NT (ZnTe/TiO₂ NT) showed significantly enhanced photocatalytic activity towards 9-AnCOOH under simulated solar light. After 70 min of irradiation, 9-AnCOOH was degraded with the removal ratio of 45% on the bare TiO₂ NT, much lower than 80%, 90%, and 100% on the ZnTe/TiO₂ NT with the ZnTe NPs prepared under the pulsed “on” potentials of −0.8, −1.0, and −2.0 V, respectively. The increased photodegradation efficiency mainly results from the improved photocurrent density as results of enhanced visible-light absorption and decreased hole-electron recombination due to the presence of narrow-band-gap p-type semiconductor ZnTe.     

Enhanced Visible‐Light‐Induced Photoelectrocatalytic Degradation of Methyl Orange by CdS Sensitized TiO2 Nanotube Arrays Electrode

In this work, CdS sensitized TiO₂ nanotube arrays (CdS/TiO₂NTs) electrode was synthesized with the CdS deposition on the highly ordered titanium dioxide nanotube arrays (TiO₂NTs) by sequential chemical bath deposition method (S‐CBD). The as‐prepared CdS/TiO₂NTs was characterized by field‐emission scanning electron microscopy (FE‐SEM) and X‐ray diffraction (XRD). The results indicated that the CdS nanoparticles were effectively deposited on the surface of TiO₂NTs. The amperometric I‐t curve on the CdS/TiO₂NTs electrode was also presented. It was found that the photocurrent density was enhanced significantly from 0.5 to 1.85 mA/cm² upon illumination with applied potential of 0.5 V at the central wavelength of 253.7 nm. The photoelectrocatalytic (PEC) activity of the CdS/TiO₂NTs electrode was investigated by degradation of methyl orange (MO) in aqueous solution. Compared with TiO₂NTs electrode, the degradation efficiencies of CdS/TiO₂NTs electrode increased from 78% to 99.2% under UV light in 2 h, and from 14% to 99.2% under visible light in 3 h, which was caused by effective separation of the electrons and holes due to the effect of CdS, hence inhibiting the recombination of electron/hole pairs of TiO₂NTs.     

Fabrication of Au‐Nanoparticle/TiO2‐Nanotubes Electrodes Using Electrochemical Methods and Their Application for Electrocatalytic Oxidation of Hydroquinone

Gold nanoparticle (Au‐NPs)‐Titanium oxide nanotube (TiO₂‐NTs) electrodes are prepared by using galvanic deposition of gold nanoparticles on TiO₂‐NTs electrodes as support. Scanning electron microscopy and energy‐dispersive X‐ray spectroscopy results indicate that nanotubular TiO₂ layers consist of individual tubes of about 60–90 nm diameters and gold nanoparticles are well‐dispersed on the surface of TiO₂‐NTs support. The electrooxidation of hydroquinone of Au‐NPs/TiO₂‐NTs electrodes is investigated by different electrochemical methods. Au‐NPs/TiO₂‐NTs electrode can be used repeatedly and exhibits stable electrocatalytic activity for the hydroquinone oxidation. Also, determination of hydroquinone in skin cream using this electrode was evaluated. Results were found to be satisfactory and no matrix effects are observed during the determination of hydroquinone content of the “skin cream” samples.     

Design of highly ordered Ag-SrTiO3 nanotube arrays for photocatalytic degradation of methyl orange

Ag-SrTiO₃ nanotube arrays were successfully prepared for the degradation of methyl orange (MO) under ultraviolet irradiation. In order to form highly ordered SrTiO₃ nanotube arrays, the preparation of TiO₂ nanotube arrays by anodic oxidation of titanium foil in different electrolytes was investigated. The selected organic solvents in electrolytes include glycerol, dimethyl sulfoxide and glycol. The results indicate that the morphology of TiO₂ nanotube arrays prepared in glycol containing ammonium fluoride electrolyte is more regular. Then SrTiO₃ nanotube arrays were synthesized by a hydrothermal method using TiO₂ nanotube arrays as the precursor. In order to further improve the photocatalytic activity of SrTiO₃ nanotube arrays, Ag nanoparticles were loaded on SrTiO₃ nanotube arrays by two sets of experiments. The loaded Ag results in an enhancement of photocatalytic activity of SrTiO₃ nanotube arrays. Moreover, the effect of pH on the photocatalytic degradation of MO was also studied.     

Au/TiO2 nanotube catalysts prepared by combining sol–gel method with hydrothermal treatment and their catalytic properties for CO oxidation

A new preparation method for Au/TiO₂ nanotubes (NTs) by combing sol–gel with hydrothermal treatment technique was developed. The TiO₂ NTs calcined at 300 °C were nearly uniform, and the gold particles were distributed homogeneously. The possible formation mechanism was suggested. The 5 % Au/TiO₂ NTs calcined at 300 °C had the best catalytic activity for CO oxidation, and their conversion of CO remained at 100 % during 60 h on stream. This preparation method could improve the thermal stability of Au/TiO₂ nanotube catalysts.     

TiO2 nanorods branched on fast-synthesized large clearance TiO2 nanotube arrays for dye-sensitized solar cells

A large clearance TiO₂ nanotube arrays (LTAs) has been synthesized by a not more than 12 h anodization duration and based on this a branched TiO₂ nanotube arrays (BLTs) has been achieved through TiO₂ nanorods branch-like grown on the LTAs. Some key factors and probable mechanisms of the fabrication processes on two novel nanoarchitectures are discussed. Exhilaratingly, it is found that the obtained LTAs has demonstrated large pore diameter and void spaces (pore diameter ∼350 nm; void spaces ∼160 nm; and tube length ∼3.5 μm), and the synthesized hierarchical BLTs, compared with conventional TiO₂ nanotube arrays, has shown a much stronger dye absorption performance and an approximately double of the solar cell efficiency (in our case from 1.62% to 3.18% under simulated AM 1.5 conditions).     

Biocompatibility and <Emphasis Type="Italic">in vitro</Emphasis> antineoplastic drug-loaded trial of titania nanotubes prepared by anodic oxidation of a pure titanium

TiO₂ nanotube (NT) arrays have been prepared by anodic oxidation of a Ti sheet, and carbon-deposited TiO₂ NT arrays have been prepared by annealing TiO₂ NT arrays in carbon atmosphere. The biocompatibility of the as-prepared NT arrays was investigated by observing the growth of osteosarcoma (MG-63) cells on the NT arrays. The application of the TiO₂ NT arrays as a drug delivery vehicle was investigated. Both the TiO₂ NTs and the carbon-modified TiO₂ NTs have good biocompatibility supporting the normal growth and adhesion of MG-63 cells with no need of extracellular matrix protein coating. The one end-opened TiO₂ NTs can be easily filled with drugs, working as an efficient drug delivery vehicle.     

Influences of the H2PtCl6 Solution's pH on the Photocatalytic Activities of Platinum-Loaded TiO2 Nanotubes

By using H₂PtCl₆ and titanate nanotubes as precursor, platinum-loaded TiO₂ nanotubes (Pt/TiO₂NTs) are prepared at different pH by deposition-precipitation method. The prepared materials are characterized with powder x-ray diffraction (XRD) and x-ray photoelectron spectra (XPS). Their photocatalytic performance is evaluated by the degradation rates of methyl orange solution under UV-vis light irradiation. Obtained results indicate that the pH of H₂PtCl₆ solution has obvious influence on the catalytic performance of Pt/TiO₂NTs.     

The Preparation and Characterization of La Doped TiO2 Nanotubes and Their Photocatalytic Activity

La-doped TiO₂ nanotubes (La/TiO₂ NTs) were prepared by the combination of sol-gel process with hydrothermal treatment. The prepared samples were characterized by using transmission electron microscopy, x-ray diffraction, x-ray photoelectron spectra, and ultraviolet-visible spectra. The photocatalytic performance of La/TiO₂ NTs was studied by testing the degradation rate of methyl orange under ultraviolet (UV) irradiation. The results indicated La/TiO₂ NTs calcined at 300°C consisted of anatase as the unique phase. The absorption spectra of the La/TiO₂ NTs showed a stronger absorption in the UV range and a slight red shift in the band gap transition than that of pure TiO₂ nanotubes. The photocatalytic performance of TiO₂ NTs could be improved by the doping of lanthanum ions, which is ascribed to several beneficial effects the formation of Ti-O-La bond and charge imbalance, existing of oxygen defects and Ti³⁺ species, stronger absorption in the UV range and a slight red shift in the band gap transition, as well as higher equilibrium dark adsorption of methyl orange. 0.75 wt% La/TiO₂ NTs had the best catalytic activity.     

Controllable incorporation of CdS nanoparticles into TiO<Subscript>2</Subscript> nanotubes for highly enhancing the photocatalytic response to visible light

A constant current electrochemical deposition was employed to incorporate CdS nanoparticles into the TiO₂ nanotube arrays (TiO₂NTs). The size and amount of CdS nanoparticles in TiO₂NTs (CdS@TiO₂NTs) were controllable via modulating current, deposition time and electrolyte concentration. It was revealed, from the scanning electron microscopy (SEM) images and X-ray photoelectron spectroscopy (XPS) in depth profile, that CdS nanoparticles were filled into TiO₂ nanotubes. A shift of the absorption edge toward the visible region under the optimal electrodeposition condition was observed with the diffuse reflectance spectroscopy (DRS). A 5-fold enhancement in the photocurrent spectrum for TiO₂NTs was observed and the photocurrent response range was significantly extended into the visible region because of the CdS incorporation. Compared with pure TiO₂NTs, under a visible light irradiation, CdS@TiO₂NTs exhibited a 3.5-fold improvement of photocatalytic activity, which was demonstrated by the photocatalytic decomposition of Rhodamine B (RhB).     

Fe_2O_3/TiO_2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO2纳米管阵列,采用化学浴方法在TiO2纳米管阵列上修饰了Fe2O3纳米颗粒。利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能。结果表明,Fe2O3纳米颗粒的修饰将TiO2纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe2O3/TiO2纳米管阵列的光电流是未修饰的TiO2纳米管阵列的9倍。而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO2纳米管阵列高出30%。     

Fe2O3/TiO2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO₂纳米管阵列,采用化学浴方法在TiO₂纳米管阵列上修饰了Fe₂O₃纳米颗粒.利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能.结果表明,Fe₂O₃纳米颗粒的修饰将TiO₂纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe₂O₃/TiO₂纳米管阵列的光电流是未修饰的TiO₂纳米管阵列的9倍.而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO₂纳米管阵列高出30%.