Electrophoretic deposition of hydroxyapatite–CaSiO3–chitosan composite coatings

Electrophoretic deposition (EPD) method has been developed for the fabrication of hydroxyapatite (HA)–CaSiO₃ (CS)–chitosan composite coatings for biomedical applications. The use of chitosan enabled the co-deposition of HA and CS particles and offered the advantage of room temperature processing of composite materials. The coating composition was varied by the variation of HA and CS concentrations in the chitosan solutions. Cathodic deposits were obtained as HA–CS–chitosan monolayers, HA–chitosan/chitosan multilayers or functionally graded materials (FGM) containing HA–chitosan and CS–chitosan layers of different composition. The thickness of the individual layers was varied in the range of 0.1–20 μm. The deposition yield was studied at different experimental conditions and compared with the results of modeling. It was shown that the moving boundary model for the two component system can explain the non-linear increase in the deposition yield with increasing HA concentration in chitosan solutions. The obtained coatings were studied by thermogravimetric analysis (TGA), differential thermal analysis (DTA) and scanning electron microscopy (SEM). Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) studies showed that these coatings provided corrosion protection of stainless steel substrates in Ringer's physiological solution. The deposition mechanism and kinetics of deposition have been discussed.     

Electrophoretic deposition of chiral polymers and composites

Electrophoretic deposition (EPD) method has been developed for the deposition of thin films of chiral polymers. EPD of poly-L-lysine (PLL) and poly-L-ornithine (PLO) films was performed for the first time on conductive substrates from aqueous and ethanol-water solutions. The deposition yield was monitored using a quartz crystal microbalance. The results demonstrated that the deposition yield can be varied by variation of the deposition time, voltage and polymer concentration in the solutions. It was shown that PLL and PLO provided stabilization and charging of hydroxyapatite (HA) nanoparticles in suspensions. Composite PLL-HA and PLO-HA films of controlled thickness were prepared by EPD. Electron microscopy investigations showed that the thickness of the PLL, PLO and composite films was varied in the range of 0-3 μm. The polymer and composite films can be used for biomedical applications.     

Electrophoretic deposition of polyacrylic acid and composite films containing nanotubes and oxide particles

Electrophoretic deposition (EPD) method has been developed for the deposition of thin films of polyacrylic acid (PAA). This method allowed the formation of uniform films of controlled thickness on conductive substrates. It was shown that PAA can be used as a common dispersing agent suitable for charging and EPD of various materials, such as multiwalled carbon nanotubes, halloysite nanotubes, MnO(2), NiO, TiO(2) and SiO(2). The feasibility of EPD of composite films containing the nanotubes and oxide particles in a PAA matrix has been demonstrated. The kinetics of deposition and deposition mechanisms were investigated and discussed. The films were studied by thermogravimetric analysis, differential thermal analysis, X-ray diffraction and scanning electron microscopy. The results indicated that film thickness and composition can be varied. Obtained results pave the way for the fabrication of PAA and composite films for biomedical, electrochemical and other applications.     

Preparation of free-standing films of natural polysaccharides using hot press technique and their surface functionalization with biomimetic apatite

This study demonstrated that gel-like polyion complexes obtained by mixing of aqueous solution of chondroitin sulfate, heparin, and hyaluronic acid with that of chitosan were able to form their free-standing films using hot press treatments. These films, having thicknesses ca. 50 and 100 μm, depending on the spacer thickness, were homogeneous and non-porous at the microscopic level, and were not water-soluble. The present fabrication process required neither cross-coupling agents nor introduction of other functional groups to the polysaccharides. Hydroxyapatite deposition on the film surfaces under body fluid conditions was also achieved.     

Fabrication and electrochemical investigation of layer-by-layer deposited titanium phosphate/Prussian blue composite films

Composite films of titanium phosphate (TiPS)/Prussian blue (PB) were fabricated by the alternative deposition of TiPS layer and PB nanocrystals. The layer of TiPS was fabricated by adsorption of hydrated titanium from aqueous Ti(SO4)2 solution and subsequent reaction with phosphate groups. The layer of PB nanocrystals was fabricated by sequential adsorption of FeCl3 solution and K4[Fe(CN)6] solution. Regular deposition of TiPS/PB composite films were verified by UV-vis absorption spectroscopy and quartz crystal microbalance measurements. The successful fabrication of the TiPS/PB composite films was further confirmed by X-ray photoelectron spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. Instead of producing films of TiPS layers alternating with PB nanocrystal layers, the TiPS/PB composite films have a structure in which the interstices of the PB nanocrystal films are filled with TiPS component. TiPS/PB composite films show enhanced electrochemical properties and improved stability in comparison with pure PB films prepared by the multiple sequential adsorption process. TiPS/PB composite films have the capability to catalyze the electrochemical reduction of H2O2 and can be used as a biosensor for detecting H2O2.     

Controlled deposition of structured polymer films: chemical and rheological factors in chitosan film formation

The technique of "spread coating" has been used to create thin films from solutions of deacetylated and butyl-modified chitosan polymer, and the effect of deposition rate on film thickness has been characterized. Results show that films of controlled thickness can be reproducibly produced and that hydrophobic modification of the polymer can extend the range over which a linear response between film thickness and deposition rate is achieved. Viscometry and fluorescence spectroscopy were also employed to characterize the micellar characteristics of solutions of both deacetylated and butyl-modified chitosan polymer. Although both deacetylated and butyl-modified chitosan solutions were found to have inter- and intramolecular interactions, as well as hydrophobic domains able to incorporate fluorophores, deacetylated chitosan was found to be more interconnected via intermolecular interactions at higher concentrations. These results are important as having the ability to understand how the introduction of hydrophobic modification, a technique shown to introduce solution-based micelle structure and micellar aggregates that support enzyme immobilization, affects film thickness and morphology of spread coated thin films will aid the long-term development and deployment of chitosan-based biofuel cell electrodes.     

Electrophoretic deposition of TiO2 nanoparticles using organic dyes

Electrophoretic deposition method has been developed for the deposition of TiO(2) nanoparticles modified with organic dyes. Alizarin red, alizarin yellow and pyrocatechol violet dyes were used for the dispersion and charging of TiO(2) in ethanol and anodic electrophoretic deposition of TiO(2) films. The deposition yield was varied by the variation of dye concentration in suspensions and deposition time. Aurintricarboxylic acid dye was used for the deposition of TiO(2) from aqueous suspensions. It was found that thin films of pure aurintricarboxylic acid and composite aurintricarboxylic acid TiO(2) films can be obtained. The deposition yield was studied by quartz crystal microbalance. Dye film thickness was varied in the range of 0.1-2 μm by variation in the deposition time at a constant voltage. The composition of the films and the amount of the deposited material can be varied by the variation of TiO(2) and dye concentration in suspensions and deposition time. The films were studied by Fourier transform infrared spectroscopy, thermogravimetric analysis, differential thermal analysis and electron microscopy. The deposition mechanisms were discussed. The electrophoretic deposition method offers advantages for the fabrication of dye-sensitized TiO(2) films.     

Preparation and Barrier Properties of Chitosan-Layered Silicate Nanocomposite Films

Summary: In this study, chitosan nanocomposite films were prepared using a solvent-casting method by incorporation of an organically modified montmorillonite (Cloisite 10A). The effect of filler concentration on the water vapor permeability, oxygen permeability, mechanical and thermal properties of the composite films was evaluated. The structure of nanocomposites and the state of intercalation of the clay were characterized by XRD. The water vapor permeability of pure chitosan films was measured as a function of relative humidity (RH). It was found that the permeability value increased with an increase in RH. The water vapor and gas permeability values of the composite films decreased significantly with increasing filler concentration. Permeation data was fitted to various phenomenological models predicting the permeability of polymer systems filled with nanoclays as a function of clay concentration and aspect ratio of nanoplatelets. According to the XRD results, an increase in basal spacing was obtained with respect to pure clay for chitosan/clay nanocomposites. This demonstrated the formation of intercalated structure of clay in the polymer matrix. Tensile strength and elongation at break of the composites increased significantly with the addition of clay, however the thermal and color properties of the films were not much affected by the intercalation of clay into polymer matrix.     

Ultrathin silica films immobilized on gold supports: fabrication, characterization, and modification

A novel method for covalent attachment of ultrathin silica films (thickness <10 nm) to gold substrates is reported. Silica layers were prepared using spin-coating of sol-gel precursor solutions onto gold substrates that were cleaned and oxidized using UV photo-oxidation in an ozone atmosphere. The gold oxide layer resulting from this process acts as a wetting control and adhesive agent for the ultrathin silica layer. Control of silica layer thickness between approximately 6 and 60 nm through modification of precursor solution composition or by repetitive deposition is demonstrated. Films were characterized using infrared spectroscopy, ellipsometry, atomic force microscopy, and cyclic voltammetry. For the standard deposition parameters developed here, films were determined to be 5.5 +/- 0.75 nm thick, and were stable in aqueous solutions ranging in pH from 2 to 10 for at least 30 min. Films contained nanoscopic defects with radii of 相似文献   

Stabilized hemocompatible coating of nitinol devices based on photo-cross-linked alginate/heparin multilayer

A novel stabilized hemocompatible multicomponent coating was engineered by consecutive alternating adsorption of two polysaccharides, alginate (Alg) and heparin (Hep), onto a Nitinol surface via electrostatic interaction in combination with photoreaction in situ. For this purpose, a photosensitive cross-linker, p-diazonium diphenyl amine polymer (PA), was used as an interlayer between alginate and heparin. The optical intensity of UV/vis spectra increased linearly with the number of layers, indicating the buildup of a multilayer structure and uniform coating. Photo-cross-linking resulted in higher stability without compromising its catalytic capacity to promote antithrombin III (ATIII)-mediated thrombin inactivation. Chromogenic assays for heparin activity proved definitively that anticoagulation activity really comes from surface-bound heparin in multilayer film, not from solution-phase free heparin that has leaked from multilayer film. The activated partial thromboplastin time (aPTT) assay showed that both (PA/Hep)8- and (PA/Alg/PA/Hep)4-coated Nitinol were less thrombogenic than the uncoated one. Yet, the latter was found to be more stable under a continuous shaken wash. In addition, (PA/Alg/PA/Hep)4 film exhibited lower surface roughness and higher hydrophilicity than (PA/Hep)8. As a result, hemolysis of (PA/Alg/PA/Hep)4 (0.34 +/- 0.064%) was lower than (PA/Hep)8 (0.52 +/- 0.241%). The naked Nitinol and (PA/Hep)8-coated Nitinol showed relatively strong platelet adhesion. On the contrary, no sign of any cellular matter was seen on the (PA/Alg/PA/Hep)4 surface. It is believed that the phenomenon of interlayer diffusion resulted in blended structures, hence, the enhanced wettability and antifouling properties after the incorporation of alginate layers. It is likely that the cooperative effect of alginate and heparin led to the excellent blood compatibility of the (PA/Alg/PA/Hep)4 coating. To simplify, there is greater advantage in utilizing cross-linked alginate/heparin surfaces rather than merely the heparin surface for improving blood- and tissue-compatible devices.     

块状壳聚糖多孔支架内交替浸渍沉积磷灰石层

在聚合物支架内沉积羟基磷灰石涂层有望提高支架的生物活性和骨传导性. 本研究采用交替浸渍沉积法, 以块状壳聚糖(Cs)三维多孔支架为沉积模板, 在氯化钙溶液和磷酸氢二钠溶液中交替浸渍, 沉积了羟基磷灰石(HA)涂层. 应用XRD、FT-IR、SEM、孔隙率测试、焙烧法和压缩实验对沉积前后支架的组成、形貌、孔隙率、无机物沉积量以及压缩强度进行了表征. 研究结果表明, 支架上沉积物为低结晶度的碳酸羟基磷灰石, 沿c轴择优生长, 与天然骨中磷灰石类似. 扫描电镜照片显示, 磷灰石在支架孔壁上的沉积量呈梯度分布, 外部沉积量多于内部, 靠近支架表面孔隙部分堵塞, 但内部仍保持连通的孔隙结构. 经6次交替浸渍处理的支架, 孔隙率为94.0%, 羟基磷灰石沉积量达到总质量的13.5%, 压缩强度则由0.055 MPa提高到0.109 MPa.     

去质子化调控的肝素/壳聚糖抗凝血多层膜

本文研究了环境pH值变化对多层膜表面性能的影响, 并且评价了组装pH值与测试pH值的差异对多层膜血液相容性的影响.     

Heparin coating durability on artificial heart valves studied by XPS and antithrombin binding capacity

The durability and functionality of a heparin coating on artificial heart valve leaflets were evaluated with X-ray photoelectron spectroscopy (XPS) and by the coatings' capacity to bind antithrombin. Current methods for accelerated life-time testing are based on exposing leaflets to water solutions. In this paper a method is explored, in which heart valve leaflets were exposed to a continuous high shear rate (4 L/min) of human citrated plasma. It was found that the heparin coating was stable and wear resistant enough to still be present after 3 weeks and to have about the same antithrombin uptake as coatings not exposed to circulating plasma. It was, however, partly destroyed by the test as found using XPS. We suggest that heparin chains from the upper layer of heparin have been torn off from the carrier chain, in combination with loss of heparin conjugate and plasma deposition in patches. This study showed that XPS provides additional information to biological measurements such as antithrombin uptake. XPS is therefore a valuable technique not only to characterize biomaterials but also to evaluate the effect of a performance test.     

Biomimetic modification of chitosan with covalently grafted lactose and blended heparin for improvement of in vitro cellular interaction

Lactose‐ and heparin‐modified chitosan films were prepared and their physical and biological properties were compared with chitosan, chitosan‐g‐heparin, and chitosan‐g‐lactose films. Atomic force microscopy (AFM) measurement showed that all these films in the dry state were rather flat with a roughness smaller than 20 nm. While the chitosan‐g‐lactose/heparin and chitosan‐g‐lactose films have the highest swelling and weight loss ratios, the chitosan and chitosan‐g‐heparin films have the lowest. The chitosan‐g‐lactose/heparin film showed stronger ability to induce chondrocyte attachment, proliferation, viability, and glycosaminoglycan (GAG) secretion than that of the chitosan, chitosan‐g‐heparin, and chitosan‐g‐lactose films. Chondrocyte aggregates and nodules were observed on the chitosan‐g‐lactose/heparin and chitosan‐g‐lactose films, which still preserved viable metabolic ability. These results show that the lactose‐modified and heparin‐incorporated chitosan film can enhance the cell–biomaterial interaction synchronously. The resulting chitosan‐g‐lactose/heparin material is more bioactive that might be applicable as promising scaffold for chondrogenesis. Copyright © 2007 John Wiley & Sons, Ltd.     

聚酰亚胺多层膜的制备及其在非线性光学中的应用

报道了一种通过旋涂制备NLO聚合物多层膜的方法.紫外-可见吸收光谱及膜的厚度表征说明,在所得多层膜的结构中,聚合物单层膜的厚度可以较好地控制在100~200nm之间,所得含有5个双层的NLO多层膜(厚度1.6μm)具有良好的结构均一性,光学显微镜下没有观察到明显的结构缺陷.与单层具有较大厚度的NLO聚合物薄膜(如2~4μm)相比,所得聚合物多层膜可以允许掺杂更多的发色团而不发生相分离.     

Structure and electrochemical properties of composite films based on poly-3,4-ethylenedioxythiophene with metallic palladium inclusions

The electrochemical behavior of PEDOT/Pd composite films obtained by the chemical deposition of ultradisperse Pd particles in the poly-3,4-ethylenedioxythiophene (PEDOT) polymer matrix was studied. The structure of the films was determined by electron microscopy and energy-dispersion X-ray fluorescence analysis. The electrochemical properties of PEDOT/Pd composite films in solutions containing hydrogen peroxide was also studied. Special attention was paid to the effect of the time of the chemical deposition of palladium in the polymer structure on the electroreduction of hydrogen peroxide in phosphate buffer solutions.     

Facile fabrication of chitosan active film with xylan via direct immersion

Chitosan film was immersed in NaOH solution with xylan to simply prepare active chitosan/xylan film. FT-IR, XRD, FE-SEM, AFM and XPS were used to evaluate the effects of xylan on the structure and morphology of chitosan film, and a wide variety of material characteristics of the chitosan/xylan composite films were investigated. The results showed that the xylan chains entered into the gap of chitosan film and became nodules, leading to strong hydrogen bonds and electrostatic interactions between chitosan and xylan. Moreover, the introduction of xylan not only resulted in stronger crystallinity and a more compact structure of chitosan film, but also had an important effect on the properties of chitosan film. The tensile strength, breaking elongation and anti-ultraviolet performance of the chitosan/xylan films were improved greatly with the increasing concentration of xylan; the water vapor transmission rate, water absorption rate and oxygen barrier property of chitosan/xylan composite films were higher than those of chitosan film; chitosan/xylan composite films still showed hydrophobicity when the xylan concentration was more than 1 %. The chitosan/xylan composite film has more potential to be used as food packaging than pure chitosan film.     

Novel hollow microcapsules based on iron-heparin complex multilayers

Iron-polysaccharide complex have been extensively utilized in the treatment of iron deficiency anemia for parenteral administration. Herein, a novel iron-heparin complexed hollow capsules with nanoscaled wall thickness have been fabricated by means of alternating deposition of ferric ions (III) (Fe+) and heparin (Hep) onto the surface of submicroscaled (488 nm) and microscaled (10.55 microm) polystyrene latex particles via both electrostatic interaction and chemical complexation processes, followed by dissolution of the cores using tetrahydrofuran. Confocal micrographs and atomic force microscopy (AFM) images prove that iron-heparin complexed submicroscaled hollow capsules keep spherical shapes in solution and even after drying. The activated partial thromboplastin time (APTT) assay shows that complexing with ferric ions do not compromise the catalytic capacity of heparin to promote antithrombin III-mediated thrombin inactivation. The anticoagulant activity value of (Fe3+/Hep)8 capsules is evaluated to be about 95.7 U/mg, indicating that approximately 0.55 mg heparin was in 1 mg powder of submicroscaled (Fe3+/Hep)8 hollow capsules. Compared with the same dosage of heparin, iron-heparin complexed hollow capsules display a more prolonged anticoagulant duration than heparin. All these results reveal that such submicroscaled iron-heparin complexed hollow capsules have application potential as an injectable anticoagulant vehicle.     

Fabrication and Characterization of Sensitive Polymer (Nano)Composites

We report on the fabrication process of a polymer sensing device based on a thin film composite obtained by spinning or casting a carbon fillers/thermoplastic polymer dispersion on a glass substrates. In this work we produce thin composite films characterized by different grade of dispersion of carbon black in polymer matrix (Poly(methyl-methacrylate), Poly(2 hydroxy-ethyl-methacrylate) and atactic poly(styrene)). We discuss, in particular the effect of the polymer and filler characteristics on the thin film morphology. Device material response towards different analytes will be also discussed. Size distribution of filler in polymer suspension and deposition method type strongly influence homogeneity and conductivity of corresponding polymer composite films and finally their sensor properties.     

Controlling the nanofiltration properties of multilayer polyelectrolyte membranes through variation of film composition

We report the use of a variety of polyelectrolyte multilayers (PEMs) as selective skins in composite membranes for nanofiltration (NF) and diffusion dialysis. Deposition of PEMs occurs through simple alternating adsorption of polycations and polyanions, and separations can be optimized by varying the constituent polyelectrolytes as well as deposition conditions. In general, the use of polycations and polyanions with lower charge densities allows separation of larger analytes. Depending on the polyelectrolytes employed, PEM membranes can remove salt from sugar solutions, separate proteins, or allow size-selective passage of specific sugars. Additionally, because of the minimal thickness of PEMs, NF pure water fluxes through these membranes typically range from 1.5 to 3 m3/(m2 day) at 4.8 bar. Specifically, to separate sugars, we employed poly(styrene sulfonate) (PSS)/poly(diallyldimethylammonium chloride) (PDADMAC) films, which allow 42% passage of glucose along with a 98% rejection of raffinose and a pure water flux of 2.4 m3/(m2 day). PSS/PDADMAC membranes are also capable of separating NaCl and sucrose (selectivity of approximately 10), while high-flux chitosan/hyaluronic acid membranes [pure water flux of 5 m3/(m2 day) at 4.8 bar] may prove useful in protein separations.