脉冲电化学驱动壳聚糖原位调控制备羟基磷灰石/银复合涂层

采用脉冲电化学驱动壳聚糖原位调控制备了具有抗菌性的羟基磷灰石/银纳米复合涂层.考察了电解液中银离子浓度、钙磷盐浓度等对复合涂层的形貌及成分的影响.探讨了壳聚糖调控羟基磷灰石和银纳米粒子的形成机理,发现在本研究的较佳实验条件为电位-1.3 V,Ag~+浓度为0.06 g·L~(-1),Ca~(2+)浓度为5 mmol·L~(-1).在此基础上对复合涂层的生物活性、生理稳定性能、抗菌性能进行分析.结果表明:复合涂层呈纳米球状,由羟基磷灰石、银、壳聚糖三相组成,并且表面有一层壳聚糖覆盖.银纳米粒子和羟基磷灰石纳米粒子在复合涂层中均匀分布.将复合涂层浸泡在SCPS溶液中37°C浸泡矿化10天后,在复合涂层表面生产细针状排列整齐的羟基磷灰石,且在(002)晶面25.8°处发生显著择优生长,表明复合涂层在快速矿化液中能诱导磷灰石生成,生物活性好.将复合涂层浸泡在37°C PBS溶液中考察其生理稳定性,壳聚糖对复合涂层中Ca~(2+)和Ag~+实现双重离子释放,且降低了离子释放速度,涂层具有良好的生理稳定性.抗菌实验表明复合涂层对大肠杆菌和金黄色葡萄球菌抗菌率达到99%以上,抗菌能力强.     

造孔剂对电泳沉积制备多孔HA涂层及其生物活性的影响

采用水热法制得的羟基磷灰石(HA)纳米粉体,分别与造孔剂葡萄糖(Glu)、壳聚糖(CS)、炭粉(C)3种微粒(＜38.5 μm)配置成质量比1∶1的悬浮液,电泳沉积 烧结制备钛基多孔HA涂层,并对制得的3种多孔HA涂层在模拟体液浸泡前后的表面形貌、化学组成及物相变化进行表征。 结果表明,经700 ℃烧结处理后制得的3种多孔HA涂层在1.5倍人体模拟体液中浸泡5 d后,多孔HA涂层表面均被层状生长的碳磷灰石颗粒完全覆盖,颗粒直径在5~25 μm,说明这些多孔HA涂层均具有良好的生物活性。 其中以CS为造孔剂制得的多孔HA涂层结合强度最高,达19.5 MPa,有望开发成为新型的人骨植入生物陶瓷材料。     

Pervaporation dehydration of ethylene glycol with chitosan–poly(vinyl alcohol) blend membranes: Effect of CS–PVA blending ratios

Chitosan–poly(vinyl alcohol), CS–PVA, blended membranes were prepared by solution casting of varying proportions of CS and PVA. The blend membranes were then crosslinked interfacially with trimesoyl chloride (TMC)/hexane. The physiochemical properties of the blend membranes were determined using Attenuated Total Reflection-Fourier Transform Infrared Spectroscopy (ATR-FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), tensile test and contact angle measurements. Results from ATR-FTIR show that TMC has crosslinked the blend membranes successfully, and results of XRD and DSC show a corresponding decrease in crystallinity and increase in melting point, respectively. The crosslinked CS–PVA blend membranes also show improved mechanical strength but lower flexibility in tensile testing as compared to uncrosslinked membranes. Contact angle results show that crosslinking has decreased the surface hydrophilicity of the blend membranes. The blend membrane properties, including contact angle, melting point and tensile strength, change with a variation in the blending ratio. They appear to reach a maximum when the CS content is at 75 wt%. In general, the crosslinked blend membranes show excellent stability during the pervaporation (PV) dehydration of ethylene glycol–water mixtures (10–90 wt% EG) at different temperatures (25–70 °C). At 70 °C, for 90 wt% EG in the feed mixture, the crosslinked blend membrane with 75 wt% CS shows the highest total flux of 0.46 kg/(m² h) and best selectivity of 986. The blending ratio of 75 wt% CS is recommended as the optimized ratio in the preparation of CS–PVA blend membranes for pervaporation dehydration of ethylene glycol.     

脉冲电化学沉积法制备羟基磷灰石/壳聚糖复合涂层的研究

采用脉冲电化学沉积法在钛金属表面制备出羟基磷灰石/壳聚糖(HA/CS)复合涂层,实现CS与HA在微观尺寸上的复合与杂化.比较了脉冲电位与恒电位模式下复合涂层的形成,研究了电位高低及壳聚糖浓度对复合涂层性能的影响.结果表明,与恒电位模式比较,脉冲电位下制备的涂层较均匀、结晶性好、CS含量高,并且HA与CS杂化程度高.脉冲...     

钛基多孔HA/SiO2复合涂层的制备及性能研究

为了制得表面多孔且与基材结合强度高的羟基磷灰石(HA)涂层,实验中以正丁醇为分散介质,以SiO2粉末为添加剂,纯钛片为基材,电泳沉积制备羟基磷灰石/二氧化硅/壳聚糖/(HA/SiO2/CS)复合涂层,经后续热处理得到多孔HA/SiO2复合涂层,采用扫描电镜(SEM)、傅立叶红外光谱仪(FT-IR)、X射线衍射仪(XRD)、万能材料试验机对涂层的表面形貌、组成、结构和结合强度进行测试和表征,并通过模拟体液(SBF)浸泡法对复合涂层的生物活性进行评价.结果表明:当悬浮液中的HA/SiO2/CS质量比为1∶1∶1时,制得的HA/SiO2/CS涂层经700℃热处理后获得的HA/SiO2复合涂层孔洞分布均匀,大孔孔径在10～15μm,小孔孔径在1～5μm;涂层与基材的结合强度达到25.5 MPa;多孔HA/SiO2复合涂层在SBF中浸泡7 d后,涂层表面碳磷灰石化;说明实验中添加SiO2所制得的多孔HA/SiO2复合涂层与钛基材结合强度高,且具有良好的生物活性.     

羟基磷灰石/氧化铁复合涂层的制备及其诱导骨生长的生物活性

用电泳沉积法制得羟基磷灰石/壳聚糖/氧化铁(HA/CS/Fe2O3)复合涂层,经700 ℃烧结处理得到HA/Fe2O3复合涂层。 通过SEM、EDS、XRD、FT-IR、电化学和万能材料试验机等对复合涂层的表面形貌、物相组成、抗腐蚀性和结合强度进行了表征和测试,最后采用1.5SBF浸泡法对复合涂层的生物活性进行了评价。 结果表明,当悬浮液中的HA、CS与Fe2O3质量比为100∶100∶1时,所制得的HA/Fe2O3复合涂层表面粗糙,抗腐蚀性强,具有良好的诱导骨生长生物活性,基体与复合涂层结合强度可达27.5 MPa。     

Improving mechanical and biological properties of macroporous HA scaffolds through composite coatings

Interconnected porous hydroxyapatite (HA) scaffolds are widely used for bone repair and replacement, owing to their ability to support the adhesion, transfer, proliferation and differentiation of cells. In the present study, the polymer impregnation approach was adopted to produce porous HA scaffolds with three-dimensional (3D) porous structures. These scaffolds have an advantage of highly interconnected porosity (≈85%) but a drawback of poor mechanical strength. Therefore, the as-prepared HA scaffolds were lined with composite polymer coatings in order to improve the mechanical properties and retain its good bioactivity and biocompatibility at the same time. The composite coatings were based on poly(d,l-lactide) (PDLLA) polymer solutions, and contained single component or combination of HA, calcium sulfate (CS) and chondroitin sulfate (ChS) powders. The effects of composite coatings on scaffold porosity, microstructure, mechanical property, in vitro mineralizing behavior, and cell attachment of the resultant scaffolds were investigated. The results showed that the scaffolds with composite coatings resulted in significant improvement in both mechanical and biological properties while retaining the 3D interconnected porous structure. The in vitro mineralizing behaviors were mainly related to the compositions of CS and ChS powders in the composite coatings. Excellent cell attachments were observed on the pure HA scaffold as well as the three types of composite scaffolds. These composite scaffolds with improved mechanical properties and bioactivities are promising bone substitutes in tissue engineering fields.     

Zn–HA–TiO2 nanocomposite coatings electrodeposited on a NiTi shape memory alloy

In this work, zinc–hydroxyapatite (Zn–HA) and zinc–hydroxyapatite–titania (Zn–HA–TiO₂) nanocomposite coatings were electrodeposited onto a NiTi shape memory alloy, using a chloride zinc plating bath. The structure of the composite coatings was characterized by X‐ray diffraction, scanning electron microscopy and high‐resolution transmission electron microscopy. According to the results, the Zn–HA–TiO₂ coating exhibited a plate‐like surface morphology, where the addition of the nanoparticles caused to an increase in roughness. It was also found that due to applying a proper stirring procedure during co‐deposition, a homogenous dispersion of the nanoparticles in the coatings was achieved. Also, the addition of the TiO₂ nanoparticles to the Zn–HA–TiO₂ coating enhanced the microhardness and wear resistance. Copyright © 2014 John Wiley & Sons, Ltd.     

Chitosan–hyaluronic acid hybrid film as a novel wound dressing: in vitro and in vivo studies

Wound dressing with high quality is a kind of highly demanded wound‐repairing products. In this article, chitosan (CS) and hyaluronic acid (HA) were used to fabricate a novel wound dressing. CS/HA composite films with high transparency could be fabricated on glass or poly(methyl methacrylate) (PMMA) substrates, but not on poly(tetrafluoroethylene) (PTFE) plate. Along with the increase of HA amount, the resulting films became rougher as detected by atomic force microscopy (AFM). Increased also are water contact angle and water‐uptake ratio. By contrast, increase of the HA amount weakened the water vapor permeability (WVP), bovine albumin adsorption, and fibroblast adhesion, which are desirable characteristics for wound dressing. In vivo animal test revealed that compared with the vaseline gauge the CS/HA film could more effectively accelerate the wound healing, and reduce the occurrence of re‐injury when peeling off the dressing again. These results demonstrate that the CS mixed with a little amount of HA may produce inexpensive wound dressing with good properties for practical applications. Copyright © 2007 John Wiley & Sons, Ltd.     

Surface modifications of Nitinol for biomedical applications

Cathodic electrophoretic deposition (EPD) has been utilized for the fabrication of composite films for the surface modification of NiTi shape memory alloys (Nitinol). In the proposed method, chitosan (CH) was used as a matrix for the incorporation of other functional materials, such as heparin, hydroxyapatite and bioglass. Chitosan-heparin films were deposited from solutions of non-stoichiometric chitosan-heparin complexes. It was found that the addition of anionic heparin to the solutions of cationic chitosan resulted in a significant increase in the cathodic deposition rate. The thickness of the films prepared by this method varied in the range of 0.1-3 microm. The ability of the chitosan-heparin films to bind antithrombin, as measured by binding of (125)I-radiolabeled antithrombin, was much greater than that of pure chitosan films. Composite chitosan-hydroxyapatite films, with thickness of 1-30 microm, were obtained as monolayers or laminates, containing chitosan-hydroxyapatite layers, separated by layers of pure chitosan. The hydroxyapatite nanoparticles showed preferred orientation in the chitosan matrix with the c-axis parallel to the substrate surface. The films showed corrosion protection of the Nitinol substrates in Ringer's physiological solutions. The feasibility of the fabrication of composite films containing hydroxyapatite and bioglass in the chitosan matrix has been demonstrated. The method offers the advantages of room temperature processing. The deposition mechanisms and possible applications of the films are discussed.     

Poly(Methyl Methacrylate) Coatings Containing Flame Retardant Additives from Suspensions in Water-2-Propanol

A dip-coating technique is designed for deposition of poly(methyl methacrylate) (PMMA) from water/2-propanol mixture, avoiding the use of traditional toxic solvents. Solutions of PMMA macromolecules with high molecular weight (M_W) are obtained for a water/2-propanol ratio of 0.15–0.33 and the solubilization mechanism is discussed. The ability to use concentrated PMMA solutions and high M_W of the polymer are the key factors for the successful dip coating deposition. The coating mass for 10 g L⁻¹ polymer solutions shows a maximum at a water/2-propanol ratio of 0.25. The deposition yield increases with the polymer concentration increase and with an increasing number of the deposited layers. PMMA deposits protect stainless steel from aqueous corrosion. The coating technique allows for the fabrication of composite coatings, containing flame-retardant materials (FRMs), such as commercial halloysite, huntite, hydrotalcite, and synthesized Al(OH)₃, in the PMMA matrix. The FRM content in the coatings is modified by variation of the FRM content in colloidal suspensions. A fundamentally new method is developed, which is based on the salting out aided dispersive extraction of Al(OH)₃ from the aqueous synthesis medium to 2-propanol. It is based on the use of hexadecylphosphonic acid molecules as extractors. The method offers advantages of reduced agglomeration.     

The evolution of growth morphology and corrosion behavior of electrodeposited Ni–P coatings on alumina borate whisker‐reinforced pure aluminum composite

The Ni–P alloy coatings were obtained on alumina borate whisker‐reinforced pure aluminum composite by electro‐deposition. The initial electro‐deposition behavior of the Ni–P alloys on the composite and pure aluminum was studied, respectively. It was found that the composition and the morphology of materials had a distinct effect on the initial electro‐deposition behavior of the Ni–P alloys. The Ni–P alloy coatings preferred to nucleate at the composite as compared with the pure aluminum. Moreover, the Ni–P particles were prone to deposit at the whisker/Al interface in the composite. The Ni–P coatings were barely depositing upon the surface of whisker during the plating process. As the deposition time increased, the Ni–P particles that were deposited on the surface of the composite grew gradually. These Ni–P particles linked to each other and eventually covered the whisker surface. Moreover, it can be found that the surfaces of the composite were gradually covered by Ni–P coatings and the anticorrosion performance of the coated composite increased remarkably with the increase in the deposition time. When the deposition time is 60 min, only the Ni–P diffraction peak could be detected. In this case, the coated composite had significantly better corrosion resistant, which is attributed to the surface of composite was perfectly covered by the Ni–P coatings. Copyright © 2012 John Wiley & Sons, Ltd.     

Chitosan–iron oxide nanobiocomposite based immunosensor for ochratoxin-A

The rabbit immunoglobulin antibodies (IgGs) have been immobilized onto nanobiocomposite film of chitosan (CH)–iron oxide (Fe₃O₄₎ nanoparticles prepared onto indium–tin oxide (ITO) electrode for detection of ochratoxin-A (OTA). Excellent film forming ability and availability of –NH₂ group in CH and affinity of surface charged Fe₃O₄ nanoparticles for oxygen support the immobilization of IgGs. Differential pulse voltammettry (DPV) studies indicate that Fe₃O₄ nanoparticles provide increased electroactive surface area for loading of IgGs and improved electron transport between IgGs and electrode. IgGs/CH–Fe₃O₄ nanobiocomposite/ITO immunoelectrode exhibits improved characteristics such as low detection limit (0.5 ng dL⁻¹), fast response time (18 s) and high sensitivity (36 μA/ng dL⁻¹ cm⁻²) with respect to IgGs/CH/ITO immunoelectrode.     

Electrophoretic deposition of chiral polymers and composites

Electrophoretic deposition (EPD) method has been developed for the deposition of thin films of chiral polymers. EPD of poly-L-lysine (PLL) and poly-L-ornithine (PLO) films was performed for the first time on conductive substrates from aqueous and ethanol-water solutions. The deposition yield was monitored using a quartz crystal microbalance. The results demonstrated that the deposition yield can be varied by variation of the deposition time, voltage and polymer concentration in the solutions. It was shown that PLL and PLO provided stabilization and charging of hydroxyapatite (HA) nanoparticles in suspensions. Composite PLL-HA and PLO-HA films of controlled thickness were prepared by EPD. Electron microscopy investigations showed that the thickness of the PLL, PLO and composite films was varied in the range of 0-3 μm. The polymer and composite films can be used for biomedical applications.     

Analytical characterization of bioactive fluoropolymer ultra-thin coatings modified by copper nanoparticles

Copper–fluoropolymer (Cu-CFx) nano-composite films are deposited by dual ion-beam sputtering. The extensive analytical characterization of these layers reveals that inorganic nanoparticles composed of Cu(II) species are evenly dispersed in a branched fluoropolymer matrix. In particular, X-ray photoelectron spectroscopy has been employed to study the surface chemical composition of the material and to assess how it changes on increasing the copper loading in the composite. Transmission electron microscopy reveals that the copper nanoclusters have a mean diameter of 2–3 nm and are homogeneously in-plane distributed in the composite films. Electrothermal atomic absorption spectroscopy has been used to study the kinetics of copper release in the solutions employed for the biological tests. The Cu-CFx layers are employed as bioactive coatings capable of inhibiting the growth of target microorganisms such as Saccharomyces cerevisiae, Escherichia coli, Staphylococcus aureus, and Lysteria. The results of the analytical characterization enable a strict correlation to be established among the chemical composition of the material surface, the concentration of copper dissolved in the microorganisms broths, and the bioactivity of the nano-structured layer.     

脉冲电沉积制备HA/ZrO2纳米复合涂层的稳定性及生物相容性评价

采用脉冲电化学沉积法成功地在生物医用钛金属表面制备出均匀的纳米HA/ZrO₂复合涂层. 通过热处理提高涂层的致密性, 同时保留涂层的微纳结构. 考察了热处理后复合涂层的成分、形貌、生物相容性及生理稳定性. X射线衍射分析表明, 复合涂层成分为HA和ZrO₂. 扫描电镜观察发现, 热处理后复合涂层的致密性有所提高. 研究发现, ZrO₂的加入大大降低了HA/ZrO₂复合涂层中钙离子的释放速度, 提高了HA/ZrO₂复合涂层的生理稳定性. 纳米划痕实验结果表明, HA/ZrO₂复合涂层具有较好的结合强度. 通过培养成骨细胞考察了复合涂层的生物相容性. Alamar Blue检测表明, HA/ZrO₂复合涂层表面细胞黏附及增殖能力较好. ALP检测发现, 热处理后HA/ZrO₂复合涂层表面的细胞分化能力较强. 综合细胞培养结果显示, HA/ZrO₂复合涂层有较好的生物相容性.     

Novel Method to Graft Chitosan on the Surface of Hydroxyapatite Nanoparticles via ＂Click＂ Reaction

In order to tune the surface properties of hydroxyapatite（HA） nanoparticles and prevent them from ag- gregation, an efficient method was proposed to graft chitosan（CS） molecules on the surface of HA via ＂click＂ reac- tion. Thermal gravimetric analysis（TGA） shows that CS was successfully grafted on the surface of HA nanoparticles and the grafting amount was about 8.9 g of CS on per hundred grams of HA. The grafted chitosan chains can prevent HA nanoparticles from aggregation and greatly enhance the colloidal stability of HA in water. The 3-（4,5-dimethylthiazoyl-2-yl）-2,5-diphenyltetrazolium bromide（MTT） assay demonstrats that the cytotoxicity of CS modified HA（HA-CS） is negligible and thus HA-CS may find potential application in biomedical fields.     

Kinetics of adsorption of Saccharomyces cerevisiae mandelated dehydrogenase on magnetic Fe3O4–chitosan nanoparticles

The adsorption of Saccharomyces cerevisiae mandelated dehydrogenase (SCMD) protein on the surface-modified magnetic nanoparticles coated with chitosan was studied in a batch adsorption system. Functionalization of surface-modified magnetic particles was performed by the covalent binding of chitosan onto the surface of magnetic Fe₃O₄ nanoparticles. Characterization of these particles was carried out using FTIR spectra, transmission electron micrography (TEM), X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). Magnetic measurement revealed that the magnetic Fe₃O₄–chitosan nanoparticles were superparamagnetic and the saturation magnetization was about 37.3 emu g⁻¹. The adsorption capacities and rates of SCMD protein onto the magnetic Fe₃O₄–chitosan nanoparticles were evaluated. The adsorption capacity was influenced by pH, and it reached a maximum value around pH 8.0. The adsorption capacity increased with the increase in temperature. The adsorption isothermal data could be well interpreted by the Freundlich isotherm model. The kinetic experimental data properly correlated with the first-order kinetic model, which indicated that the reaction is the adsorption control step. The apparent adsorption activation energy was 27.62 kJ mol⁻¹ and the first-order constant for SCMD protein was 0.01254 min⁻¹ at 293 K.     

原位复合法制备层状结构的壳聚糖/羟基磷灰石纳米材料

用原位复合法制备了高性能的壳聚糖/羟基磷灰石(CS/HA)纳米复合材料.用预先沉积的壳聚糖膜将含有羟基磷灰石前驱体的壳聚糖溶液与凝固液隔离,同时控制壳聚糖沉积与羟基磷灰石前驱体转化为羟基磷灰石的过程,使其缓慢且有序地进行.当pH值改变时,质子化的壳聚糖分子链在负电层诱导下有序沉积并形成层状结构与羟基磷灰石原位生成CS/HA,并实现二者分子级复合.XRD和TEM测试证实原位生成的磷酸盐是羟基磷灰石,且其颗粒长约为100nm,宽30～50nm.SEM结果表明,用原位复合法制备的材料具有层状结构,CS/HA(质量比100/5)纳米复合材料弯曲强度高达86MPa,比松质骨的高3～4倍,相当于密质骨的1/2,有望用于可承重部位的组织修复材料.     

Composition and properties of water-soluble products formed in the reaction of chitosan with Fe(III) in aqueous FeCl<Subscript>3</Subscript> solutions

The effect of preparation conditions on the composition and properties of products of Fe(III) reaction with chitosan was studied. The reaction was carried out by partial neutralization of moderately concentrated FeCl₃ solutions with chitosan followed by precipitation in an organic precipitant.Translated from Zhurnal Prikladnoi Khimii, Vol. 77, No. 11, 2004, pp. 1880–1886.Original Russian Text Copyright © 2004 by Anpilogova, Murinov.