硅油基底表面铁薄膜的生长机理及表面有序结构

利用直流溅射方法在液体基底(硅油)表面成功制备出金属铁薄膜系统，研究了其生长机理及特征的表面有序结构.实验发现铁薄膜的生长过程与液相基底表面非磁性金属薄膜的情况类似，基本服从二阶段生长模型.连续铁薄膜中可观测到尺寸巨大的圆盘形有序结构，其生长演化与溅射功率、沉积时间和真空环境中的生长时间等实验条件密切相关.实验证明，此类有序结构是在薄膜内应力作用下，铁原子及原子团簇在液体表面自由扩散迁移，并最终在硅油基底表面某些区域成核凝聚所致.在较大溅射功率和沉积时间条件下，圆盘外部区域的铁薄膜中形成周期分布的波纹褶皱，其波长约为10 μm，波峰基本与圆盘的边界平行.进一步研究表明：在沉积过程中，由于沉积铁原子的局域能量作用，导致硅油的表面层结构发生改变而形成一聚合物层；在随后的冷却过程中，聚合物层的强烈收缩使铁薄膜处于很大的压应力场中，促使薄膜起皱形成波纹结构. 关键词： 液体基底 铁薄膜 生长机理 有序结构     

封面说明

采用气相沉积方法在液相基底表面成功制备了一种具有近似自由支撑的新型铁薄膜系统．该薄膜的生长机制服从所谓的二阶段生长模型：沉积铁原子在液相基底表面首先成核并凝聚成准圆形原子团簇；然后这些原子团簇在液体表面做无规扩散和旋转运动，从而形成分枝状凝聚体(上图)，并随着薄膜名义厚度的增加，分枝状凝聚体逐渐相互连接成网状薄膜，     

液相基底温度对沉积银原子及其团簇凝聚过程的影响

研究了沉积银原子及其团簇在液相基底(硅油)表面的凝聚过程随基底温度的变化关系.实验结果表明:当硅油基底温度升高时,沉积银原子及其团簇的凝聚过程仍基本符合二阶段生长模型; 样品具有明显的边缘效应,在样品中心区域,凝聚体的覆盖率比边缘的相应值小,样品中心区域的凝聚体覆盖率先随薄膜名义厚度的增加迅速增大,然后逐渐趋于饱和,覆盖率趋于饱和时的膜厚值随基底温度的升高而降低; 对于一定的薄膜名义厚度,硅油基底温度越高,中心区域的凝聚体覆盖率越小.银原子凝聚体的分枝平均长度随基底温度的演化过程也具有类似的规律.对沉积银 关键词： 薄膜 液相基底 分枝状凝聚体 生长模型     

六方晶格基底上薄膜生长的Monte Carlo模拟研究

利用Monte Carlo（MC）方法,模拟研究了六方晶格基底上薄膜生长的初始阶段岛的形貌和岛的尺寸与薄膜覆盖度以及入射粒子沉积速率之间的关系. 结果表明在基底温度为300K时,岛的形貌主要表现为分形生长,随着薄膜覆盖度的增加,岛的分形枝簇变大,岛的数目不断减少. 在同样的温度下,随着入射粒子沉积速率的增大,薄膜表面的形貌逐步由少数聚集型岛核分布状态向众多各自独立的离散型岛核分布状态过渡. 进一步研究得出,薄膜覆盖度和入射粒子沉积速率对粒子扩散能力的影响最终导致岛的形貌发生了改变.     

基底显微结构对薄膜生长影响的Monte Carlo模拟研究

利用Monte Carlo方法研究了基底显微结构对薄膜生长的影响. 对不同显微结构基底上薄膜生长的初始阶段岛的形貌和尺寸与薄膜覆盖度和入射粒子沉积速率之间的关系进行了模拟和分析. 模型中考虑了粒子沉积、吸附粒子扩散和蒸发等过程. 结果表明,基底显微结构对薄膜生长具有明显影响. 当沉积温度为300K、沉积速率为0.005ML/s（Monolayer/second,简称ML/s）、覆盖度为0.05ML时,四方基底上薄膜生长呈现凝聚生长. 随着覆盖度增加,岛的尺寸变大,岛的数目减少. 而对于六方基底,当覆盖度从0.05ML变化到0.25ML时,薄膜生长经历了一个从分散生长过渡到分形生长的过程. 无论是四方还是六方基底,随着沉积速率的增加,岛的形貌由少数聚集型岛核分布状态向众多各自独立的离散型岛核分布状态过渡.     

动力学晶格蒙特卡洛方法模拟Cu薄膜生长

利用动力学晶格蒙特卡洛方法模拟了Cu薄膜在Cu(100)面上的三维生长过程。模型中考虑了四个动力学过程:原子沉积、增原子迁移、双原子迁移和台阶边缘原子迁移,各动力学过程发生的概率由多体势函数确定。讨论了基底温度、沉积速率及原子覆盖率对Cu原子迁移、成核和表面岛生长等微观生长机制的影响;获得了Cu薄膜的表面形貌图并计算了表面粗糙度。模拟结果表明,随基底温度升高或沉积速率下降,岛的平均尺寸增大,数目减少,形状更加规则。低温时,Cu薄膜表现为分形的离散生长,高温时,Cu原子迁移能力增强形成密集的岛。Cu薄膜表面粗糙度随着基底温度的升高而迅速减小;当基底温度低于某一临界温度时,表面粗糙度随原子覆盖率或沉积速率的增大而增大;当基底温度超过临界温度时,表面粗糙度随原子覆盖率或沉积速率的变化很小,基本趋于稳定。     

准自由支撑铝薄膜中有序表面结构的自组织生长

利用真空热蒸发方法在液体基底表面成功制备出具有自由支撑边界条件的金属铝薄膜系统，研究了薄膜中自发形成的自边界向内部区域逐渐生长而呈带状分布的有序表面结构.该有序结构的形成与薄膜厚度、沉积速率和真空环境中的生长时间等实验参数密切相关，其形成过程可用一个三阶段生长模型来描述.实验证明此类有序结构是在薄膜内应力作用下，铝原子及原子团簇在液体表面自由扩散凝聚所致.进一步的理论研究表明：基于特征的边界条件和固液相互作用，该自由支撑铝薄膜系统中包含了丰富的正弦形内应力分布，各种具有不同振幅和频率的正弦形内应力的合成可形成矩形状畴块和带状有序结构. 关键词： 液体基底 铝薄膜 自组织生长 有序结构     

颗粒大小分布对铁薄膜矫顽力的影响研究

研究了沉积在液体基底表面铁薄膜的矫顽力与温度的依赖关系。研究发现：在极低温下，矫顽力先随温度增加迅速增大，在临界温度Tc=10-15K左右达最大。超过该温度后。矫顽力又快速下降，至65K后下降幅度减慢。分析表明：高于临界温度时沉积在液体基底表面铁薄膜的矫顽力与温度的关系强烈地受颗粒大小分布的影响；导致在Tc上、下温区磁化机制的改变可能是与铁薄膜及其氧化层中的无序自旋在低温时出现类自旋玻璃态密切相关。     

颗粒大小分布对铁薄膜矫顽力的影响研究

研究了沉积在液体基底表面铁薄膜的矫顽力与温度的依赖关系.研究发现:在极低温下,矫顽力先随温度增加迅速增大,在临界温度Tc=10～15 K左右达最大,超过该温度后,矫顽力又快速下降,至65 K后下降幅度减慢.分析表明:高于临界温度时沉积在液体基底表面铁薄膜的矫顽力与温度的关系强烈地受颗粒大小分布的影响;导致在Tc上、下温区磁化机制的改变可能是与铁薄膜及其氧化层中的无序自旋在低温时出现类自旋玻璃态密切相关.     

微波化学气相沉积中气压对金刚石薄膜生长速率和质量的影响

研究了微波化学气相沉积中沉积气压对金刚石薄膜生长速率和质量的影响.研究表明，金刚石薄膜的生长速率随沉积气压的提高而增大，生长速率与沉积气压为线性关系.在高沉积气压下生长的金刚石薄膜晶形完整，拉曼谱测量可得到锐利的金刚石相的峰，但电压-电流测量表明，随着制备时沉积气压的提高，金刚石薄膜的暗电流增大，膜的电学质量下降. 关键词： 金刚石薄膜 生长速率 沉积气压     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.