Near-wall scaling for turbulent boundary layers with adverse pressure gradient

A new extended inner scaling is proposed for the wall layer of wall-bounded flows under the influence of both wall shear stress and streamwise pressure gradient. This scaling avoids problems of the classical wall coordinates close to flow separation and reattachment. Based on the proposed extended velocity and length scales a universal nondimensional family of velocity profiles is derived for the viscous region in the vicinity of a wall that depend on wall distance and a parameter α quantifying the importance of the streamwise pressure gradient with respect to the wall shear stress in the momentum balance. The performance of the proposed extended scaling is investigated in two different flow fields, a separating and reattaching turbulent boundary layer and a turbulent flow over a periodic arrangement of smoothly contoured hills. Both flows are results of highly resolved direct numerical simulation (DNS). The results show that the viscous assumptions are valid up to about two extended wall units. If the profiles are scaled by the extended inner coordinates, they seem to behave in a universal way. This gives rise to the hope that a universal behavior of velocity profiles can be found in the proposed extended inner coordinates even beyond the validity of the extended viscous law of the wall.      

Turbulent separated reattached flow in a two-dimensional curved-wall diffuser

A turbulent separation-reattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter. The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel. At the inlet of the diffuser, Reynolds number based on the diffuser height is 1.2×10⁵ and the velocity is 25.2m/s. The results of experiments are presented and analyzed in new defined streamline-aligned coordinates. The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress. A scale is formed using the maximum Reynolds shear stresses. It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law exists in the forward shear flow. Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model. The length scale is taken from that developed by Schofield and Perry. The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield-Perry velocity scale as well as the edge velocity of the boundary layer. The results of these experiments are presented in this paper.     

Time-dependent drag reduction and ageing in aqueous solutions of a cationic surfactant

The turbulent pipe flow of a highly dilute aqueous cationic surfactant solution is investigated by means of a pulsed ultrasound Doppler method with special emphasis on the wall boundary layer. The velocity profiles are recorded for several Reynolds numbers at varying ages of the solution. The wall shear stress velocities u _τ used for the normalization of the velocity profiles are determined by fitting the measured profiles to the universal linear velocity profile in the viscous sublayer. The theoretical pressure loss is then calculated from the numerical values of u _τ and compared to the experimental values. Two different scaling methods are discussed for the velocity fluctuations concerning the correlation of the root-mean square values with the effect and the amount of drag reduction. It is shown that outer scaling with the mean velocity is appropriate for the detection of drag reduction in surfactant solutions, rather than inner scaling with the wall shear stress velocity, which is common practice in investigations of 'usual' turbulent flows.     

A method for estimating wall friction in turbulent wall-bounded flows

We describe a simple method for estimating turbulent boundary layer wall friction using the fit of measured velocity data to a boundary layer model profile that extends the logarithmic profile all the way to the wall. Two models for the boundary layer profile are examined, the power-series interpolation scheme of Spalding and the Musker profile which is based on the eddy viscosity concept. The performance of the method is quantified using recent experimental data in zero pressure gradient flat-plate turbulent boundary layers, and favorable pressure gradient turbulent boundary layers in a pipe, for which independent measurements of wall shear are also available. Between the two model profiles tested, the Musker profile performs much better than the Spalding profile. Results show that the new procedure can provide highly accurate estimates of wall shear with a mean error of about 0.5% in friction velocity, or 1% in shear stress, an accuracy that is comparable to that from independent direct measurements of wall shear stress. An important advantage of the method is its ability to provide accurate estimates of wall shear not only based on many data points in a velocity profile but also very sparse data points in the velocity profile, including only a single data point such as that originating from a near-wall probe.     

Experimental study on flow control of the turbulent boundary layer with micro-bubbles

The effect of micro-bubbles on the turbulent boundary layer in the channel flow with Reynolds numbers (Re) ranging from \(0.87\times 10 ^{5}\) to \(1.23\times 10^{5}\) is experimentally studied by using particle image velocimetry (PIV) measurements. The micro-bubbles are produced by water electrolysis. The velocity profiles, Reynolds stress and instantaneous structures of the boundary layer, with and without micro-bubbles, are measured and analyzed. The presence of micro-bubbles changes the streamwise mean velocity of the fluid and increases the wall shear stress. The results show that micro-bubbles have two effects, buoyancy and extrusion, which dominate the flow behavior of the mixed fluid in the turbulent boundary layer. The buoyancy effect leads to upward motion that drives the fluid motion in the same direction and, therefore, enhances the turbulence intense of the boundary layer. While for the extrusion effect, the presence of accumulated micro-bubbles pushes the flow structures in the turbulent boundary layer away from the near-wall region. The interaction between these two effects causes the vorticity structures and turbulence activity to be in the region far away from the wall. The buoyancy effect is dominant when the Re is relatively small, while the extrusion effect plays a more important role when Re rises.     

Turbulent boundary layer on a mildly curved convex surface

Mean flow and turbulence measurements have been made in a boundary layer which grows first on a flat' wall and then on a convex wall of radius of curvature approximately 100 times the boundary layer thickness. The turbulence data include profiles of the four non-zero components of the Reynolds stress tensor and three triple velocity products obtained at five stream-wise positions. A number of measurements were also made for comparison in the boundary layer on a flat wall under the same conditions. The effects of convex curvature are to reduce turbulent intensities, shear stress and wall friction by approximately 10% of their plane flow values; the triple velocity products are halved in the curved layer. The measurements supplement the small quantity of previously published data available for testing mathematical models of turbulence. The results show the same general trends that have been observed in earlier investigations but there are significant differences in detail, notably in respect of levels of the normal stresses.     

暖季强降雨对多年冻土南界斜坡路基稳定性影响分析

为阐明表面活性剂水溶液的减阻作用,使用LDV对零压梯度的二维湍流平板边界层中的CTAB 表面活性剂水溶液的湍流特性进行了实验研究. 结果表明：与牛顿流体相比,CTAB水溶液边 界层的粘性底层增厚;主流时均速度分布有被层流化的趋势,对数分布域上移;主流方向速 度湍动强度峰值减小,且远离壁面,在靠近边界层中部,出现第2峰值;垂直于主流方向的 速度湍动强度受到了大幅度抑制,雷诺应力沿着边界层厚度方向几乎为零. 结果说明CTAB 水溶液具有减弱湍流湍动各个成分相关度的作用,从而能够使雷诺应力降低、湍流能量生成 项减小最终降低流体的输送动力.     

Using digital holographic microscopy for simultaneous measurements of 3D near wall velocity and wall shear stress in a turbulent boundary layer

A digital holographic microscope is used to simultaneously measure the instantaneous 3D flow structure in the inner part of a turbulent boundary layer over a smooth wall, and the spatial distribution of wall shear stresses. The measurements are performed in a fully developed turbulent channel flow within square duct, at a moderately high Reynolds number. The sample volume size is 90 × 145 × 90 wall units, and the spatial resolution of the measurements is 3–8 wall units in streamwise and spanwise directions and one wall unit in the wall-normal direction. The paper describes the data acquisition and analysis procedures, including the particle tracking method and associated method for matching of particle pairs. The uncertainty in velocity is estimated to be better than 1 mm/s, less than 0.05% of the free stream velocity, by comparing the statistics of the normalized velocity divergence to divergence obtained by randomly adding an error of 1 mm/s to the data. Spatial distributions of wall shear stresses are approximated with the least square fit of velocity measurements in the viscous sublayer. Mean flow profiles and statistics of velocity fluctuations agree very well with expectations. Joint probability density distributions of instantaneous spanwise and streamwise wall shear stresses demonstrate the significance of near-wall coherent structures. The near wall 3D flow structures are classified into three groups, the first containing a pair of counter-rotating, quasi streamwise vortices and high streak-like shear stresses; the second group is characterized by multiple streamwise vortices and little variations in wall stress; and the third group has no buffer layer structures.     

输气管道壁面涂料减阻机理的实验研究

用IFA-300热线风速仪以高于对应最小湍流时间尺度的分辨率精细测量了风洞中不同壁面涂料的管道湍流边界层不同法向位置流向速度分量的时间序列信号,利用湍流边界层近壁区域对数律平均速度剖面与壁面摩擦速度、流体黏性系数等内尺度物理量的关系和壁面摩擦速度与壁面摩擦切应力的关系,在准确测量湍流边界层近壁区域对数律平均速度剖面的基础上,间接测量湍流边界层的壁面摩擦阻力．对不同壁面涂料的壁湍流脉动速度信号用子波分析进行多尺度分解,用子波系数的瞬时强度因子和平坦因子检测管道湍流边界层中的多尺度相干结构,提取不同尺度相干结构的条件相位平均波形,对比研究输气管道壁面涂料的减阻机理．     

A bypass wake induced laminar/turbulent transition

The process of laminar to turbulent transition induced by a von Karman vortex street wake, was studied for the case of a flat plate boundary layer. The boundary layer developed under zero pressure gradient conditions. The vortex street was generated by a cylinder positioned in the free stream. An X-type hot-wire probe located in the boundary layer, measured the streamwise and normal to the wall velocity components. The measurements covered two areas; the region of transition onset and development and the region where the wake and the boundary layer merged producing a turbulent flow. The evolution of Reynolds stresses and rms-values of velocity fluctuations along the transition region are presented and discussed. From the profiles of the Reynolds stress and the mean velocity profile, a ‘negative' energy production region along the transition region, was identified. A quadrant splitting analysis was applied to the instantaneous Reynolds stress signals. The contributions of the elementary coherent structures to the total Reynolds stress were evaluated, for several x-positions of the near wall region. Distinct regions in the streamwise and normal to the wall directions were identified during the transition.     

Near wall characterization of the flow over a two-dimensional steep smooth hill

Near-wall data for the strongly perturbed flow in a neutrally stable boundary layer encountering a steep, smooth, two-dimensional hill are presented. Observations were made on the centerplane of a water channel at thirteen stations relative to the hill by laser Doppler anemometry. The large reverse flow region that is formed on the lee of the hill was particularly scrutinized through seven measuring stations. Results are presented for the mean and turbulent properties of the flow. Wall shear stress was evaluated through fitting procedures that resorted to the near wall behavior of the velocity profile. Logarithmic fits as well as predictions through the Reynolds stress profiles are also presented.     

单一倾斜热线探头在三维湍流场中的应用

研究的目的是确立用单一倾斜热线探头进行三维湍流测试的基础技术．在阐明基本原理，基础方程式的基础上，对比实验结果，证明应用所阐明的方法、用单一倾斜热线探头进行三维湍流测试是切实可行的．对边界层壁面附近的测试结果表明考虑平均速度和变动速度的高次相关项后可以得到更加精确的实验结果．     

Layered structure of turbulent plane wall jet

This paper investigates the layered structure of a turbulent plane wall jet at a distance from the nozzle exit. Based on the force balances in the mean momentum equation, the turbulent plane wall jet is divided into three regions: a boundary layer-like region (BLR) adjacent to the wall, a half free jet-like region (HJR) away from the wall, and a plug flow-like region (PFR) in between. In the PFR, the mean streamwise velocity is essentially the maximum velocity, and the simplified mean continuity and mean momentum equations result in a linear variation of the mean wall-normal velocity and Reynolds shear stress. In the HJR, as in a turbulent free jet, a proper scale for the mean wall-normal flow is the mean wall-normal velocity far from the wall and a proper scale for the Reynolds shear stress is the product of the maximum mean streamwise velocity and the velocity scale for the mean wall-normal flow. The BLR region can be divided into four sub-layers, similar to those in a canonical pressure-driven turbulent channel flow or shear-driven turbulent boundary layer flow. Building on the log-law for the mean streamwise velocity in the BLR, a new skin friction law is proposed for a turbulent wall jet. The new prediction agrees well with the correlation of Bradshaw and Gee (1960) over moderate Reynolds numbers, but gives larger skin frictions at higher Reynolds numbers.     

Investigation of the heat transfer mechanism in supersonic turbulent boundary layers

A method is described for calculating turbulent Prandtl numbers from Mach number and total temperature profiles in supersonic boundary layers. The calculations are based on boundary layer measurements in the Mach number range from 3.5 to 5. The investigations clearly indicate that in addition to accurate profile measurements reliable values of shear stress and heat flux at the wall must exist, in order to be able to calculate the turbulent Prandtl number in the viscous regime of the boundary layer. For flow conditions with and without heat transfer, the derived turbulent Prandtl numbers indicate that the turbulent transport of heat decreases much faster towards the wall than the turbulent transport of momentum. The results of the analysis show that only the unequivocal qualitative result of increasing turbulent Prandtl numbers in the viscous region of the boundary layer, can be expected. The variation of the turbulent Prandtl number can be described successfully using a simple approximation, based on the mixing length concept, and is applied to the calculation of total temperature distribution using the law of the wall for compressible flow.     

适用于浸入边界法的大涡模拟紊流壁面模型

基于近壁定常剪切应力假设,提出了一种新的适用于浸入边界法的大涡模拟紊流壁面模型。通过引入壁面滑移速度,修正了线性速度剖面计算得到的壁面剪切应力,使之满足Werner-Wengle模型。将其应用于平板紊流和高Re数圆管紊流的数值模拟,对比采用和不采用壁面模型的结果得知,采用此模型的速度剖面与实验值吻合良好,验证了此模型的有效性。研究了不同欧拉/拉格朗日网格相对位置对结果的影响,证明了此模型具有较好的鲁棒性,以及可根据局部流动状态和网格精度自动开闭的特点。     

Effect of a moving wall on a fully developed, equilibrium turbulent boundary layer

Experiments were conducted in a wind tunnel to assess the effect of a moving wall on a fully developed, equilibrium turbulent boundary layer. Pitot-static and total head probes were used in conjunction with both single- and two-component hot-wire anemometer probes to quantify the effect of wall motion on the boundary layer velocity statistics. A variable speed, seamless belt formed the wind tunnel test section wall. When stationary, the belt was found to possess a fully developed, equilibrium turbulent boundary layer in excellent agreement with archival data. With the tunnel wall moving at the free-stream speed, and at a sufficient distance above the wall, the velocity statistics in the moving-wall boundary layer were found to collapse well when scaled as a self-preserving turbulent wake. The near-wall mean velocity profile of the moving wall was found to exhibit an extended region of linearity compared to canonical turbulent boundary layer and internal flows. This can be attributed to the reduced shear resulting from wall motion and the subsequent reduction in Reynolds stress. Received: 2 June 1999/Accepted: 8 August 2000     

FLOW STRUCTURE IN THE TURBULENT BOUNDARY LAYER OVER DIRECTIONAL RIBLETS SURFACES

本文采用时间解析的二维粒子图像测速技术,对零压力梯度光滑以及汇聚和发散沟槽表面平板湍流边界层统计特性和流动结构进行了研究.结果表明在垂直于汇聚和发散沟槽表面的对称平面内,相对于光滑壁面,发散沟槽壁面使当地边界层厚度、壁面摩擦阻力、湍流脉动、雷诺应力等明显减小;而汇聚沟槽壁面对湍流边界层特性和流动结构的影响正好相反,汇聚沟槽使壁面流体有远离壁面向上运动的趋势,因而导致边界层厚度增加了约43%;同时,在汇聚沟槽表面情况下流向大尺度相干结构更容易形成,这对减阻是不利的.此外,顺向涡数量在湍流边界层的对数区均存在一个极大值,发散沟槽表面所对应的极大值位置更靠近沟槽壁面,而在汇聚沟槽表面则有远离壁面的趋势,由顺向涡诱导产生的较强的喷射和扫掠运动会在湍流边界层中产生较强的剪切作用,顺向涡数量的减少是发散沟槽壁面当地摩擦阻力降低的主要原因.     

A time-resolved hot-wire shear stress probe for turbulent flow: use of laminar flow calibration

A specially-designed rotating rig for producing near Couette flow was used in the calibration of a marginally elevated hot-wire shear stress probe. The probe was then used for measurements in both the turbulent boundary layer and pipe flows. Results showed that the mean wall shear stress can be accurately predicted and the near wall statistical quantities of intensity, skewness and flatness of shear stress fluctuations concurred well with previous works, thereby supporting the notion of a time-resolved shear stress probe for turbulent flows.     

PIV study on a shock-induced separation in a transonic flow

A transonic interaction between a steady shock wave and a turbulent boundary layer in a Mach 1.4 channel flow is experimentally investigated by means of particle image velocimetry (PIV). In the test section, the lower wall is equipped with a contour profile shaped as a bump allowing flow separation. The transonic interaction, characterized by the existence in the outer flow of a lambda shock pattern, causes the separation of the boundary layer, and a low-speed recirculating bubble is observed downstream of the shock foot. Two-component PIV velocity measurements have been performed using an iterative gradient-based cross-correlation algorithm, providing high-speed and flexible calculations, instead of the classic multi-pass processing with FFT-based cross-correlation. The experiments are performed discussing all the hypotheses linked to the experimental set-up and the technique of investigation such as the two-dimensionality assumption of the flow, the particle response assessment, the seeding system, and the PIV correlation uncertainty. Mean velocity fields are presented for the whole interaction with particular attention for the recirculating bubble downstream of the detachment, especially in the mixing layer zone where the effects of the shear stress are most relevant. Turbulence is discussed in details, the results are compared to previous study, and new results are given for the turbulent production term and the return to isotropy mechanism. Finally, using different camera lens, a zoom in the vicinity of the wall presents mean and turbulent velocity fields for the incoming boundary layer.     

Numerical prediction of turbulent boundary layer noise from a sharp-edged flat plate

An efficient hybrid uncorrelated wall plane waves–boundary element method (UWPW-BEM) technique is proposed to predict the flow-induced noise from a structure in low Mach number turbulent flow. Reynolds-averaged Navier-Stokes equations are used to estimate the turbulent boundary layer parameters such as convective velocity, boundary layer thickness, and wall shear stress over the surface of the structure. The spectrum of the wall pressure fluctuations is evaluated from the turbulent boundary layer parameters and by using semi-empirical models from literature. The wall pressure field underneath the turbulent boundary layer is synthesized by realizations of uncorrelated wall plane waves (UWPW). An acoustic BEM solver is then employed to compute the acoustic pressure scattered by the structure from the synthesized wall pressure field. Finally, the acoustic response of the structure in turbulent flow is obtained as an ensemble average of the acoustic pressures due to all realizations of uncorrelated plane waves. To demonstrate the hybrid UWPW-BEM approach, the self-noise generated by a flat plate in turbulent flow with Reynolds number based on chord Re_c = 4.9 × 10⁵ is predicted. The results are compared with those obtained from a large eddy simulation (LES)-BEM technique as well as with experimental data from literature.