Synthesis of nanosized TiO2/SiO2 particles using microwave processes and their photocatalytic activity on the decomposition of orange II

The nanosized titania and TiO₂/SiO₂ particles were prepared by the microwave-hydrothermal method. The effect of physical properties TTIP/TEOS ratio and calcination temperature has been investigated. The major phase of the pure TiO₂ particle is of the anatase structure, and a rutile peak was observed above 800°C. In TiO₂/SiO₂ particles, however, no significant rutile phase was observed, although the calcination temperature was 900°C. No peaks for the silica crystal phase were observed at either silica/titania ratio. The crystallite size of TiO₂/SiO₂ particles decreases as compared to pure TiO₂ at high calcination temperatures. The TiO₂/SiO₂ particles show higher activity on the photocatalytic decomposition of orange II as compared to pure TiO₂ particles.     

Promotion effect of adsorbed water/OH on the catalytic performance of Ag/activated carbon catalysts for CO preferential oxidation in excess H2

Activated carbon (AC) supported silver catalysts were prepared by incipient wetness impregnation method and their catalytic performance for CO preferential oxidation (PROX) in excess H₂ was evaluated. Ag/AC catalysts, after reduction in H₂ at low temperatures (≤200 °C) following heat treatment in He at 200 °C (He200H200), exhibited the best catalytic properties. Temperature-programmed desorption (TPD), X-ray diffraction (XRD) and temperature-programmed reduction (TPR) results indicated that silver oxides were produced during heat treatment in He at 200 °C which were reduced to metal silver nanoparticles in H₂ at low temperatures (≤200 °C), simultaneously generating the adsorbed water/OH. CO conversion was enhanced 40% after water treatment following heat treatment in He at 600 °C. These results imply that the metal silver nanoparticles are the active species and the adsorbed water/OH has noticeable promotion effects on CO oxidation. However, the promotion effect is still limited compared to gold catalysts under the similar conditions, which may be the reason of low selectivity to CO oxidation in PROX over silver catalysts. The reported Ag/AC-S-He catalyst after He200H₂00 treatment displayed similar PROX of CO reaction properties to Ag/SiO₂. This means that Ag/AC catalyst is also an efficient low-temperature CO oxidation catalyst.     

PdCl2-CuCl2/Al2O3催化剂低温催化CO氧化的失活机理

采用X射线衍射、N₂吸-脱附、X射线光电子能谱分析、氢气-程序升温还原和原位红外漫反射等方法对新鲜和失活的PdCl₂-CuCl₂/Al₂O₃低温催化CO氧化催化剂进行表征,研究了高相对湿度(100%)下催化剂的失活机理.结果表明,催化剂表面沉积的水使得活性铜物种容易从催化剂表面向载体孔道内部迁移,由于Pd、Cu相互作用弱化从而减弱了Pd与Cu物种间的相互作用,使得催化剂的氧化还原性能受到影响,抑制了Pd⁰再氧化为Pd²⁺的过程,从而因CO氧化反应中催化剂氧化还原循环受阻而导致失活.     

Ni/SiO2-ZrO2催化剂焙烧温度对其催化愈创木酚加氢脱氧性能的影响简

采用化学沉淀法合成了SiO₂-ZrO₂复合氧化物载体,并以浸渍法制备了Ni/SiO₂-ZrO₂双功能催化剂,考察了焙烧温度对催化剂结构及其催化愈创木酚加氢脱氧制环己烷性能的影响. 结果表明,经500℃焙烧催化剂的加氢脱氧活性最高,在Ni金属中心和SiO₂-ZrO₂载体材料的协同作用下,愈创木酚转化率为100%,环己烷选择性为96.8%. 对催化剂进行N₂物理吸附、H₂化学吸附、X射线衍射分析、H₂程序升温还原、NH₃程序升温脱附与Raman光谱等表征后发现,合成的SiO₂-ZrO₂为无定形的酸碱两性氧化物;经500℃焙烧的催化剂样品的有效比表面积和孔体积均明显增大,表面酸量最多,硝酸镍分解成小颗粒的NiO较易被H₂还原,这些特性是该催化剂样品具有高效加氢脱氧活性的原因.     

Thermal Stability of Pt/Al2O3 Catalysts Prepared by Sol-Gel

A series of Pt/Al₂O₃ catalysts were prepared using a sol-gel method. The influence of several parameters used in the synthesis including: metal content, identity of the metal precursor, and the water/alkoxide ratio on the structural properties of the fresh (dried) and calcined samples were studied. It was found that the BET surface area decreased with an increase in the platinum content. A surface area of 500 m²/g was obtained following calcination at 773 K. The structure of fresh samples as determined by FTIR corresponded to that of a pseudoboehmite structure. Samples prepared using a water/alkoxide ratio (H₂O/ATB) of 9 showed a well-defined, uniform pore size distribution following calcination at 773 K. Metal dispersions comparable to those obtained using impregnation methods were obtained. Aging studies (calcination at 873 K for 24 h) performed on these catalysts, exhibited sintering behavior which were similar to Pt/Al₂O₃ catalysts prepared by other methods. The sample prepared using a H₂O/ATB ratio of 9 had the highest surface area and was more thermally resistant towards metal sintering. A bimodal metal particle size distribution was observed: some particles exhibited sintering while others of similar size showed a greater thermal stability to sintering. The sample having the largest surface area and the highest thermal stability following thermal treatment was a consequence of a more condensed structure and a higher pore roughness obtained after drying the gel. This enabled the formation of an alumina structure which was more amorphous and limited aggregation of platinum particles due to surface diffusion within the pore structure.     

Effect of calcination conditions on MoO3/SiO2 catalysts for synthesis of methylphenyl carbonate

The effect of calcination conditions on MoO₃/SiO₂ catalysts for the synthesis of methylphenyl carbonate was investigated in terms of catalytic activities and surface properties. The calcination temperature was varied in the range of 300 to 800^oC. These calcination conditions have shown a close relationship with the catalyst activities. The optimal calcination temperature of MoO₃/SiO₂was found to be around 550-600^oC. The catalysts were characterized by XRD, SEM, FT-IR and XPS analysis.     

Kinetics of low temperature CO oxidation over Pt/SnO2 catalyst

In a CO−O₂ stoichiometric mixture, the kinetic parameters, reaction order, rate constant and activation energy of CO oxidation over a Pt/SnO₂ catalyst have been measured using a fixed bed flow reactor near 0°C. The results show that it is a first-order reaction. The activation energy of CO oxidation over Pt/SnO₂ prepared with SnO₂ calcined at 300°C was approximately 21 kJ/mol. The activation energy of CO oxidation over Pt/SnO₂ changed slowly with SnO₂ calcination temperature above 400°C, and reached approximately 45 kJ/mol.     

Effect of the preparation conditions on the physicochemical and catalytic properties of Ni<Subscript>2</Subscript>P/SiO<Subscript>2</Subscript> catalysts

The effect of the reduction conditions on the physicochemical and catalytic properties of Ni₂P/SiO₂ catalysts was studied. The catalysts were prepared by impregnating silica with a solution of nickel acetate and diammonium hydrogen phosphate followed by drying, calcination, and temperature-programmed reduction. The Ni₂P/SiO₂ catalysts were reduced prior to hydrodeoxygenation (HDO) of methyl palmitate in the catalytic reactor (in situ) at temperatures of 550, 600, and 650 °С for 3 h and at 600 °С for 1 and 6 h. The reduction temperature and reduction time were shown to affect the conversion of methyl palmitate, and the optimal reduction conditions of the Ni₂P/SiO₂ catalysts were found. The Ni₂P/SiO₂ catalyst synthesized according to a widely used preparation method, including steps of passivation and rereduction at 450 °С in addition to the reduction step, is inferior in activity to the samples prepared in situ.     

Preparation of the Pd/C catalysts: A molecular-level study of active site formation

This review summarizes the results of molecular-level studies on the mechanism of Pd/C catalyst formation from the PdCl₂ precursor. Two processes occur in acidic media during the contact of H₂PdCl₄ with carbon: (a) adsorption of palladium chloride to form surface complexes and (b) redox interaction between PdCl₂ and carbon with the formation of palladium metal particles. The ratio between these adsorbed palladium species depends on the conditions of adsorption and especially on the size of carbon support grains and the oxidative atmosphere. The observations are explained by the fact that carbon support exhibits electrochemical and ligand properties. X-ray diffraction, X-ray scattering, XPS, and high-resolution electron microscopy revealed that the nanostructure of carbon materials, in particular the extent of their three-dimensional ordering, is crucial for the ligand properties. The presence of two forms, metallic and ionic, of sorbed palladium determines the bimodal size distribution of the metal. After the reduction of ionic species, metal particles are “blocked” with support. The nature of the ionic forms of palladium (mostly (PdCl₂)_n) clusters chemically and epitaxially bound to the carbon surface suggests the mechanisms of the bimodal distribution of the supported metal particles on the surface and the methods for the control of the ratio between “blocked,” low-dispersed, and highly-dispersed particles in the catalyst. One of these methods is the use of palladium polynuclear hydroxo complexes (PHCs) with low oxidation potentials as starting compounds for catalysts preparation. The data on the PHC structure in a solution and its change upon the adsorption of PHC on the surface of the carbon material obtained by the¹⁷O,²³Na,¹³³Cs, and³⁵Cl NMR techniques are discussed. PHCs are shown to be a clew of the [Pd(OH)₂]_n polymeric filament, whose fractions are bound with alkali metal ions. When PHC is adsorbed on the surface of the carbon support and then dried, palladium oxide is formed from which highly dispersed metal particles are formed during reduction. The nature of alkali metal ions in PHC affects the activity of the Pd/C catalyst. An important role of the ligand, electrochemical, and lyophilic properties of carbon material during the formation of the species of the active catalyst component is discussed.     

Infrared spectra and the structures of the chemisorbed species resulting from the adsorption of propene and propane on a Pt/SiO2 catalyst

The infrared spectrum from propane adsorbed on a Pt/SiO₂ catalyst at room temperature is readily interpreted in terms of the presence of a predominantly propylidyne surface species; additional absorptions in the spectrum from propene indicate the presence also of non-dissociative species, i.e. considerable amounts of di-σ species and a smaller amount of the π-bonded species. With adsorbed propene, heating in vacuum above 130°C leads to the breakdown of the initially adsorbed species to give ethylidyne, implying CC bond-breaking and an increasingly alkenyl-type dehydrogenated surface species. The addition of H₂ at room temperature to the species from adsorbed propene leads largely to the removal of the surface species as propane; the residual surface species are alkyl in type and at elevated temperatures (>100°C) are reversibly dehydrogenated by pumping. Methane desorption is observed in H₂ at 300°C and the spectra of the remaining surface alkyl species show the presence of lengthened hydrocarbon chains, implying an overall process of disproportionation.     

Gold, palladium and gold–palladium supported on silica catalysts prepared by sol–gel method: synthesis, characterization and catalytic behavior in the ethanol steam reforming

Noble-metal-based catalysts supported on silica (Au/SiO₂, Pd/SiO₂ and Au–Pd/SiO₂) were prepared by the sol–gel method and were evaluated in the steam reforming of ethanol for hydrogen production. The catalysts were characterized by N₂ physisorption (BET/BJH methods), X-ray diffraction, temperature programmed reduction analysis, H₂ chemisorption, atomic absorption spectrophotometry and Raman spectroscopy. The structural characterization of the Au- and Pd-containing catalysts after calcination showed that the solids are predominantly formed by Au⁰, Pd⁰ and PdO species and was observed that the metallic Pd dispersion diminished in the presence of Au⁰. The results revealed that the catalytic behavior could be influenced by the experimental conditions and the nature of the catalyst employed. The Pd/SiO₂ catalyst showed the best performance among the catalysts tested at the highest reaction temperature (600 °C) due to the more effective action of the metallic active phase, which covers a greater area in this sample. At this same reaction temperature, the Au–Pd/SiO₂ catalyst showed a significant deactivation, probably due to the lower Pd dispersion presented by this catalyst.     

Influence of the thermal treatment conditions and composition of bimetallic catalysts Fe—Pd/SiO2 on the catalytic properties in phenylacetylene hydrogenation

The supported bimetallic Fe—Pd/SiO₂ catalysts with the different Fe (0.025—8 mass.%) and Pd (0.05—3.2 mass.%) loadings were synthesized by the incipient wetness impregnation of support. The samples were heat-treated under different conditions (calcination in air at 240—350 °C or reduction in an H₂ flow at 400 °C). The X-ray phase analysis revealed the formation of Pd⁰, α-Fe₂O₃ and Fe₃O₄ phases after calcination of the samples at 240—260 °C. The reduction of the calcined Fe—Pd samples in an H₂ flow at 400 °C enables the formation of Fe⁰ nanoparticles of size 17—20 nm. The synthesized catalytic systems were studied in the selective hydrogenation of phenylacetylene at room temperature and atmospheric pressure in a solvent (ethanol, propanol). The catalytic properties of the Fe—Pd catalysts depend on the nature of solvent, catalyst composition, and thermal treatment conditions. The application of the Fe—Pd bimetallic catalysts with a low Pd loading of 0.05—0.1 mass.% made it possible to reach the high activity and selectivity to styrene (91%) at the complete conversion of phenylacetylene.     

Influence of the activation temperature on structural and textural properties of NiMo/Al2O3 hydrodesulfurization catalysts

Investigations of a commercial NiMo/Al₂O₃ hydrodesulfurization (HDS) catalyst are directed towards optimization of the activation procedure of HDS catalyst concerning active phase formation and thermal stability. Structural and textural data obtained with XRD, IR-FTIR, XPS and LTNA reveal that the optimal temperature for the formation of active species on the catalyst surface and an appropriate pore structure is 300°C.     

The structure-reactivity relationship for metathesis reaction between ethylene and 2-butene on WO<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> catalysts calcinated at different temperatures

The WO₃/SiO₂ catalyst for propylene production by metathesis of ethylene and 2-butene was preheated at different temperatures to investigate the effect of calcination temperatures on the active species and elucidate the structure-reactivity relationship. The influence of calcination temperatures on the physicochemical properties of the catalyst, relating to the active species, was deduced from an array of characterization results. It has been found that the surface tetrahedral tungsten species with high metal-support interaction were formed on the catalyst calcined at 550°C as confirmed by Raman, UV-Vis and TPR-H₂ spectra.     

Thermal behavior of LDH 2CuAl.CO<Subscript>3</Subscript> and 2CuAl.CO<Subscript>3</Subscript>/Pd

Cu/Al layered double hydroxide (LDH) can be used as a catalyst for important processes such as cross-coupling reactions. This property may be improved by adding palladium by either impregnation or intercalation. Therefore, the LDH matrix and its composites with Pd⁰ or [PdCl₄]^2? have been prepared. By powder X-ray diffraction, FT-infrared spectroscopy, thermogravimetric and elemental analysis it was determined the LDH formula Cu₄Al₂(OH)₁₂CO₃.4H₂O, with malachite as the second phase. The LDH thermal decomposition occurs between 120 and 600 °C, having as intermediates the double oxi-hydroxide and the mixed oxide phases. At 800 °C the residue is composed of CuO and CuAl₂O₄. The composites were obtained employing [PdCl₄]^2? and Pd₂(dba)₃ as precursors, and the solvent choice for this process was shown to be of significant importance: the materials obtained using DMF had Pd impregnated in the surface, while the usage of water promoted the intercalation of [PdCl₄]^2? in the LDH matrix. The thermogravimetric analysis was able to distinguish the mode of supporting palladium between the composites being a reliable characterization for such task.     

trans‐[1,3‐Bis(2,4,6‐trimethylphenyl)imidazolidin‐2‐ylidene]dichlorido(triphenylphosphine‐κP)palladium(II)

The title complex, [PdCl₂(C₂₁H₂₆N₂)(C₁₈H₁₅P)], shows slightly distorted square‐planar coordination around the Pd^II metal centre. The Pd—C bond distance between the N‐heterocyclic ligand and the metal atom is 2.028 (5) Å. The dihedral angle between the two trimethylphenyl ring planes is 36.9 (2)°.     

Improvement of the Pd/Al2O3 Catalyst by the Control of the Sol-Gel Preparative Parameters

In this work, the metal dispersion of the Pd/Al₂O₃ catalyst prepared by sol-gel method is improved by an adequate optimisation of the preparative variables. First, the gelation temperature and the ageing time are selected, in order to avoid the reduction of the metal precursor (palladium acetylacetonate, Pd(acac)₂) by the solvent (sec-butanol, sB). The metal sintering effect on the catalysts treated in oxygen at 500°C is then minimized when the alumina pore size is controlled by the variation of the alumium alkoxide (AsB) concentration and the acetic acid amount ([AcA]/[AsB]). The appearance of new palladium particles on the alumina surface and the matching between the particle diameters and the pore sizes were also effective for the metallic surface area improvement on the samples treated in oxygen at 800°C. Compared to the reference catalysts, the higher metal dispersion obtained on the sol-gel ones was the determinant factor for their higher catalytic activity in methane combustion.     

Influence of H3PMo12O40/SiO2 thermal treatment on adsorbed forms of formaldehyde and formic acid

Effect of the H₃PMo₁₂O₄₀/SiO₂(P-Mo-HPA) thermal treatment on adsorbed forms of HCOOH and H₂CO has been studied by IR spectroscopy. On the sample pretreated at 150°C, HCOOH adsorbed mainly as hydrogen-bonded complexes. The HPA calcination at 350°C resulted in the formation of surface formates along with hydrogen-bonded complexes. This proves the formation of coordinatively unsaturated surface cations (Lewis acid sites) during HPA dehydration. Alteration of the surface composition due to dehydration was found to have a major influence on the H₂CO adsorbed forms.     

SiO2气凝胶的制备及微孔分布

本文以正硅酸乙酯(TEOS)为原料，水和乙醇为溶剂，盐酸和氨水为催化剂，采用溶胶-凝胶，水热合成和低温冷冻干燥等工艺，制备了SiO₂气凝胶，研究了pH值、TEOS浓度及焙烧温度对气凝胶的比表面积、孔径分布的影响。结果表明：在碱性条件下，制得的气凝胶比表面积较大，孔径较窄。气凝胶在较高温度下，比表面积有所下降，孔径略微变粗。     

Calcination of SiO2-aerogel in Oxidizing Atmosphere

Differences in mass loss occurring in the course of dynamic and isothermal heating of SiO₂-aerogel and changes of specific surface and hydrophylicity during calcination were studied by thermal analysis. SiO₂-aerogel was prepared from tetramethoxysilane (TMOS) hydrolyzed by ammonia solution at 0°C with molar ratio TMOS: H₂O:NH₄OH 4:1:0.01. Differences are caused mainly by oxidation of organic matter and by diffusion of products of the oxidation. Heat transfer has none or little effect on the differences. Samples calcined at temperatures about 300°C reach maximum hydrophilicity though they still contain small amounts of residual organic matter. This revised version was published online in July 2006 with corrections to the Cover Date.