Fabrication of polyaniline/ heterojunction structure using plasma enhanced polymerization technique

The work reports on the fabrication of a p–n heterojunction structure comprised of polyaniline (PANI) and TiO₂ nanoparticles. PANI was deposited by plasma enhanced polymerization on TiO₂ thin film substrates. The structural and the crystalline properties demonstrated the coherence and the substantive interaction of the plasma polymerized PANI molecules with the TiO₂ nanoparticle thin film. The UV–Vis studies of PANI/TiO₂ thin film supported the internalization of PANI with TiO₂ nanoparticles due to π–π^* transition of the phenyl rings with the lone pair electrons () of the nitrogen atom present in the PANI molecules. The I–V characteristics of the PANI/TiO₂ heterojunction structure were obtained in the forward and the reverse biased at applied voltage ranging from −1 V to +1 V with a scan rate of 2 mV/s. The proficient current in the PANI/TiO₂ heterojunction structure was attributed to the well penetration of PANI molecules into the pores of the TiO₂ nanoparticle thin film. The I–V characteristics ensured an efficient charge movement at the junction of PANI/TiO₂ interface and thus, behaved as a typical ohmic system.     

Bimodal Nanoparticle Size Distributions Produced by Laser Ablation of Microparticles in Aerosols

Silver nanoparticles were produced by laser ablation of a continuously flowing aerosol of microparticles in nitrogen at varying laser fluences. Transmission electron micrographs were analyzed to determine the effect of laser fluence on the nanoparticle size distribution. These distributions exhibited bimodality with a large number of particles in a mode at small sizes (3–6-nm) and a second, less populated mode at larger sizes (11–16-nm). Both modes shifted to larger sizes with increasing laser fluence, with the small size mode shifting by 35% and the larger size mode by 25% over a fluence range of 0.3–4.2-J/cm². Size histograms for each mode were found to be well represented by log-normal distributions. The distribution of mass displayed a striking shift from the large to the small size mode with increasing laser fluence. These results are discussed in terms of a model of nanoparticle formation from two distinct laser–solid interactions. Initially, laser vaporization of material from the surface leads to condensation of nanoparticles in the ambient gas. Material evaporation occurs until the plasma breakdown threshold of the microparticles is reached, generating a shock wave that propagates through the remaining material. Rapid condensation of the vapor in the low-pressure region occurs behind the traveling shock wave. Measurement of particle size distributions versus gas pressure in the ablation region, as well as, versus microparticle feedstock size confirmed the assignment of the larger size mode to surface-vaporization and the smaller size mode to shock-formed nanoparticles.     

Imaging {Au0-PAMAM} Gold-dendrimer Nanocomposites in Cells

Dendrimer nanocomposites (DNC) are hybrid nanoparticles formed by the dispersion and immobilization of guest atoms or small clusters in dendritic polymer matrices. They have a great potential in biomedical applications due to their controlled composition, predetermined size, shape and variable surface functionalities. In this work, d=5–25nm spherical nanoparticles composed of gold and poly(amidoamine) (PAMAM) dendrimers have been selected to demonstrate this nanoparticle based concept. {Au(0)_n-PAMAM} gold dendrimer nanocomposites with a well-defined size were synthesized and imaged by transmission electron microscopy both in vitro and in vivo. DNC have also the potential to be used for imaging and drug delivery vehicles either by utilizing bioactive guests or through the incorporation of radioactive isotopes, such as Au-198.     

Room-temperature synthesis of gold nanoparticles and nanoplates using Shewanella algae cell extract

Biosynthesis of spherical gold nanoparticles and gold nanoplates was achieved at room temperature and pH 2.8 when cell extract from the metal-reducing bacterium Shewanella algae was used as both a reducing and shape-controlling agent. Cell extract, prepared by sonicating a suspension of S. algae cells, was capable of reducing 1 mol/m³ aqueous AuCl₄ ⁻ ions into elemental gold within 10 min when H₂ gas was provided as an electron donor. The time interval lapsed since the beginning of the bioreductive reaction was found to be an important factor in controlling the morphology of biogenic gold nanoparticles. After 1 h, there was a large population of well-dispersed, spherical gold nanoparticles with a mean size of 9.6 nm. Gold nanoplates with an edge length of 100 nm appeared after 6 h, and 60% of the total nanoparticle population was due to gold nanoplates with an edge length of 100–200 nm after 24 h. The yield of gold nanoplates prepared with S. algae extract was four times higher than that prepared with resting cells of S. algae. The resulting biogenic gold nanoparticle suspensions showed a large variation in color, ranging from pale pink to purple due to changes in nanoparticle morphology.     

Green synthesis of silver nanoparticle by <Emphasis Type="Italic">Penicillium purpurogenum</Emphasis> NPMF: the process and optimization

An eco-friendly microbial method for synthesis of silver colloid solution with antimicrobial activity is developed using a fungal strain of Penicillium purpurogenum NPMF. It is observed that increase in concentration of AgNO₃ increases the formation of silver nanoparticle. At 5 mM concentration highly populated polydispersed nanoparticles form. Furthermore, change in pH of the reaction mixture leads to change in shape and size of silver nanoparticles. At lower pH two peaks are observed in the absorption spectra showing polydispersity of nanoparticles. However, highly monodispersed spherical nanoparticles of 8–10 nm size form with 1 mM AgNO₃ concentration at pH 8. Antimicrobial activity of nanoparticles is demonstrated against pathogenic gram negative bacteria like Escherichia coli and Pseudomonas aeruginosa, and gram positive bacteria like Staphylococcus aureus. The antimicrobial activity of silver nanoparticles obtained at different initial pH show strong dependence on the surface area and shape of the nanoparticles.     

Large nonlinear optical properties of Fe2O3 nanoparticles

Nonlinear optical properties of Fe₂O₃ nanoparticles were investigated by the signal-beam Z-scan technique with Ar⁺ and Ne–He lasers. The largest reported effective nonlinear coefficient, n₂=−8.07×10⁻⁷ cm²/W, was obtained. It is demonstrated that the nonlinear optical response originals from quantum confinement effect.     

Bactericidal effects of Ag nanoparticles immobilized on surface of SiO2 thin film with high concentration

Bactericidal activity of high concentration Ag nanoparticles immobilized on surface of an aqueous sol–gel silica thin film was investigated against Escherichia coli and Staphylococcus aureus bacteria. Size of the surface nanoparticles was estimated in the range of 35–80 nm by using atomic force microscopy. Due to accumulation of the silver nanoparticles at near the surface (at depth of 6 nm and about 40 times greater than the silver concentration in the sol), the synthesized Ag–SiO₂ thin film (with area of 10 mm²) presented strong antibacterial activities against E. coli and S. aureus bacteria with relative rate of reduction of the viable bacteria of 1.05 and 0.73 h⁻¹ for initial concentration of about 10⁵ cfu/ml, respectively. In addition, the dominant mechanism of silver release in long times was determined based on water diffusion in surface pores of the silica film, unlike the usual diffusion of water on the surface of silver-based bulk materials. Therefore, the Ag nanoparticles embedded near the surface of the SiO₂ thin film can be utilized in various antibacterial applications with a strong and long life activity.     

In situ preparation of high relaxivity iron oxide nanoparticles by coating with chitosan: A potential MRI contrast agent useful for cell tracking

Iron oxide nanocrystals are of considerable interest in nanoscience and nanotechnology because of their nanoscale dimensions, nontoxic nature, and superior magnetic properties. Colloidal solutions of magnetic nanoparticles (ferrofluids) with a high magnetite content are highly desirable for most molecular imaging applications. In this paper, we present a method for in situ coating of superparamagnetic iron oxide (SPIO) with chitosan in order to increase the content of magnetite. Iron chloride salts (Fe³⁺ and Fe²⁺) were directly coprecipitated inside a porous matrix of chitosan by Co-60 γ-ray irradiation in an aqueous solution of acetic acid. Following sonication, iron oxide nanoparticles were formed inside the chitosan matrix at a pH value of 9.5 and a temperature of 50 °C. The [Fe³⁺]:[Fe²⁺]:[NH₄OH] molar ratio was 1.6:1:15.8. The final ferrofluid was formed with a pH adjustment to approximately 2.0/3.0, alongside with the addition of mannitol and lactic acid. We subsequently characterized the particle size, the zeta potential, the iron concentration, the magnetic contrast, and the cellular uptake of our ferrofluid. Results showed a z-average diameter of 87.2 nm, a polydispersity index (PDI) of 0.251, a zeta potential of 47.9 mV, and an iron concentration of 10.4 mg Fe/mL. The MRI parameters included an R1 value of 22.0 mM⁻¹ s⁻¹, an R2 value of 202.6 mM⁻¹ s⁻¹, and a R2/R1 ratio of 9.2. An uptake of the ferrofluid by mouse macrophages was observed. Altogether, our data show that Co-60 γ-ray radiation on solid chitosan may improve chitosan coating of iron oxide nanoparticles and tackle its aqueous solubility at pH 7. Additionally, our methodology allowed to obtain a ferrofluid with a higher content of magnetite and a fairly unimodal distribution of monodisperse clusters. Finally, MRI and cell experiments demonstrated the potential usefulness of this product as a potential MRI contrast agent that might be used for cell tracking.     

Biosynthesized Silica Nanosuspension as Thermal Fluid in Parabolic Solar Panels

In this work, the production of biologically synthesized silica nanoparticles was proposed to prepare a nanosuspension as a thermal fluid in parabolic solar panels at the laboratory level. Silica nanoparticles were produced from construction sand in two stages. Biosynthesis broth was produced by Aspergillus niger aerated fermentation in a 1 L bioreactor for 9 days. Each supernatant was contacted with 18% construction sand in a 500 L reactor with mechanical agitation, at a temperature of 25 °C, and a contact time of 30 min. Subsequently, the separation process was carried out. For day 9, a pH value of 1.71 was obtained as well as acid concentrations of 15.78 g/L for citrus and 4.16 g/L for malic. The metal extraction efficiency of Si nanoparticles was 19%. The vibration peaks in the FTIR were characteristic of the presence of silica nanoparticles in wavenumbers 1020 cm⁻¹ and 1150 cm⁻¹. Finally, a prototype solar radiation test bench for parabolic systems was built and provided with a radiation source that falls on a translucent pipe that transports the nanoparticles, which has a pump and a series of thermocouples. The heat capacity of the biotechnologically produced silica nanoparticle suspension was 0.72 ± 0.05 kJ/kgK, using material and energy balances in the flow circuit.     

Preparation,Characterization and Application of Fluorescent Terbium Complex-Doped Zirconia Nanoparticles

Novel zirconia-based fluorescent terbium nanoparticles have been prepared as a fluorescent nanoprobe for time-resolved fluorescence bioassay. The nanoparticles were prepared in a water-in-oil (W/O) microemulsion consisting of a strongly fluorescent Tb³⁺ complex, N,N,N¹, N¹-[2,6-bis(3′-aminomethyl-1′-pyrazolyl)-phenylpyridine]tetrakis(acetate)-Tb³⁺(BPTA-Tb³⁺), Triton X-100, hexanol, and cyclohexane by controlling co-condensation of Zr(OCH₂CH₃)₄ and ZrOCl_2. The characterizations by transmission electron microscopy and fluorometric methods indicate that the nanoparticles are uniform in size, 33± 4 nm in diameter, and have a fluorescence quantum yield of 8.9% and a long fluorescence lifetime of 2.0 ms. The zirconia-based fluorescent terbium nanoparticles show high stability against basic dissolution in a high pH aqueous buffer compared to the silica-based nanoparticles. A surface modification and bioconjugation method for the fluorescent nanoparticles was developed, and the nanoparticle-conjugated streptavidin (SA) was used for time-resolved floroimmunoassy (TR-FIA) of human prostate specific antigen (PSA). The result shows that the zirconia-based fluorescent terbium nanoparticles are useful as a fluorescent nanoprobe for time-resolved fluorescence bioassay.     

Fabrication of nano-structured polythiophene nanoparticles in aqueous dispersion

The synthetic route of unsubstituted polythiophene (PT) nanoparticles was investigated in aqueous dispersion via Fe³⁺-catalyzed oxidative polymerization. With this new synthetic method, high conversion of thiophene monomers was obtained with only a trace of FeCl₃. The dispersion state showed that the PT nanoparticles were well dispersed in many polar solvents, compared to non-polar solvents, such as acetone, chloroform, hexane, and ethyl acetate. To compare the photoluminescence properties between PT nanoparticle dispersion and PT bulk polymers, the PL intensities were measured in the same measuring conditions. Further, core–shell poly(styrene/thiophene) (poly(St/Th)) latex particles were successfully prepared by Fe³⁺-catalyzed oxidative polymerization during emulsifier-free emulsion polymerization. The different polymerization rates of each monomer resulted in core–shell structure of the poly(St/Th) latex particles. The PL data of the only crumpled shells gave evidence that the shell component of core–shell poly(St/Th) latex particles is indeed PT, which was corroborated by SEM data. PL intensity of the core–shell poly(St/Th) nanoparticle dispersion was much higher than that of the PT nanoparticle dispersion, due to its thin shell layer morphology, which was explained by the self-absorption effect.     

Large two-photon absorbance of chitosan–ZnS quantum dots nanocomposite film

ZnS semiconductor nanoparticles with average size of 3.4 nm were prepared in situ in chitosan film. TEM, UV–vis spectra and PL spectra show the ZnS nanoparticles in chitosan template were monodispersed and well passivated. The two-photon absorption coefficient (β) of the chitosan–ZnS quantum dots (QDs) nanocomposite film was obtained to be 2.29×10² cm/Gw from a standard Z-scan setup with femtosecond laser pusles at 790 nm wavelength. Results show the novel biomacromolecule/QDs nanocomposite film has large third-order optical nonlinear absorption, the mechanism responsible for which was discussed.     

Influence of pH on the preparation of dispersed Ag–TiO<Subscript>2</Subscript> nanocomposite

In this paper, data concerning the effect of pH on the morphology of Ag–TiO₂ nanocomposite during photodeposition of Ag on TiO₂ nanoparticles is reported. TiO₂ nanoparticles prepared by sol–gel method were coated with Ag by photodeposition from an aqueous solution of AgNO₃ at various pH levels ranging from 1 to 10 in a titania sol, under UV light. The as-prepared nanocomposite particles were characterized by UV–vis absorption spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), and N₂ adsorption/desorption method at liquid nitrogen temperature (−196 °C) from Brunauer–Emmett–Teller (BET) measurements. It is shown that at a Ag loading of 1.25 wt.% on TiO₂, a high-surface area nanocomposite morphology corresponding to an average of one Ag nanoparticle per titania nanoparticle was achieved. The diameter of the titania crystallites/particles were in the range of 10–20 nm while the size of Ag particles attached to the larger titania particles were 3 ± 1 nm as deduced from crystallite size by XRD and particle size by TEM. Ag recovery by photo harvesting from the solution was nearly 100%. TEM micrographs revealed that Ag-coated TiO₂ nanoparticles showed a sharp increase in the degree of agglomeration for nanocomposites prepared at basic pH values, with a corresponding sharp decrease in BET surface area especially at pH > 9. The BET surface area of the Ag–TiO₂ nanoparticles was nearly constant at around a value of 140 m² g⁻¹ at all pH from 1–8 with an anomalous maximum of 164 m² g⁻¹ when prepared from a sol at pH of 4, and a sharp decrease to 78 m² g⁻¹ at pH of 10.     

Detection and Characterization of Boric Acid and Borate Ion Binding to Cytochrome c Using Multiple Quantum Filtered NMR

The application of multiple quantum filtered (MQF) NMR to the identification and characterization of the binding of ligands containing quadrupolar nuclei to proteins is demonstrated. Using relaxation times measured by MQF NMR multiple binding of boric acid and borate ion to ferri and ferrocytochrome c was detected. Borate ion was found to have two different binding sites. One of them was in slow exchange, k_diss = 20 ± 3 s⁻¹ at 5°C and D₂O solution, in agreement with previous findings by ¹H NMR (G. Taler et al., 1998, Inorg. Chim. Acta 273, 388–392). The triple quantum relaxation of the borate in this site was found to be governed by dipolar interaction corresponding to an average B–H distance of 2.06 ± 0.07 Å. Other, fast exchanging sites for borate and boric acid could be detected only by MQF NMR. The binding equilibrium constants at these sites at pH 9.7 were found to be 1800 ± 200 M⁻¹ and 2.6 ± 1.5 M⁻¹ for the borate ion and boric acid, respectively. Thus, detection of binding by MQF NMR proved to be sensitive to fast exchanging ligands as well as to very weak binding that could not be detected using conventional methods.     

In Vivo Detection of N-Coupled Protons in Rat Brain by ISIS Localization and Multiple-Quantum Editing

Three-dimensional image-selected in vivo spectroscopy (ISIS) was combined with phase-cycled ¹H–¹⁵N heteronuclear multiple-quantum coherence (HMQC) transfer NMR for localized selective observation of protons J-coupled to ¹⁵N in phantoms and in vivo. The ISIS–HMQC sequence, supplemented by jump–return water suppression, permitted localized selective observation of 2–5 μmol of [¹⁵N_indole]tryptophan, a precursor of the neurotransmitter serotonin, through the ¹⁵N-coupled proton in 20–40 min of acquisition in vitro at 4.7 T. In vivo, the amide proton of [5-¹⁵N]glutamine was selectively observed in the brain of spontaneously breathing ¹⁵NH₄⁺-infused rats, using a volume probe with homogeneous ¹H and ¹⁵N fields. Signal recovery after three-dimensional localization was 72–82% in phantoms and 59 ± 4% in vivo. The result demonstrates that localized selective observation of ¹⁵N-coupled protons, with complete cancellation of all other protons except water, can be achieved in spontaneously breathing animals by the ISIS–HMQC sequence. This sequence performs both volume selection and heteronuclear editing through an addition/subtraction scheme and predicts the highest intrinsic sensitivity for detection of ¹⁵N-coupled protons in the selected volume. The advantages and limitations of this method for in vivo application are compared to those of other localized editing techniques currently in use for non-exchanging protons.     

A turn-on fluorescent chemosensor for Hg based on phenanthroline fluorophore

Dipyrido[3,2-a:2′,3′-c]-phenazine (L) was employed as a selectively fluorescent chemosensor for Hg²⁺ in DMF solution under buffered conditions with its fluorescence being strongly increased. The fluorescence increasing was attributed to the formation of L–Hg²⁺ by 1:1 complex ratio (K=3.7×10⁵ M⁻¹), which constitutes the basis for the determination of Hg²⁺ with the prepared chemosensor. The experiment results also show that the response behavior of L to Hg²⁺ is pH independent in the range of pH 6.0–9.0 and show excellent sensitivity and selectivity for Hg²⁺ over other examined metal ions.     

Solubility and acid-base properties and activity coefficients of chitosan in different ionic media and at different ionic strengths, at T = 25 °C

Studies on the acid-base properties and solubility of a polyammonium polyelectrolyte (chitosan) with different molecular weights (MW 310 and 50 kDa), were performed at T = 25 °C, in the pH range 2.5–7. The protonation of chitosan was investigated by potentiometry ([H⁺]-glass electrode) in NaCl, NaNO₃ and mixed NaNO₃ + Na₂SO₄ ionic media, at different ionic strengths. Protonation constants were calculated as a function of dissociation degree α by means of two different models, namely, a simple linear model and the modified Henderson–Hasselbalch equation. Experimental data were also fitted using a model independent of α (Diprotic-like model), according to which the acid-base properties can be simply described by two protonation constants in all the acidic pH range. The dependence on ionic strength of protonation constants in NaCl aqueous solution was modelled by Specific ion Interaction Theory (SIT). The ion pair formation between protonated chitosan and Cl⁻, NO₃⁻ and SO₄²⁻ was also considered, and the relative formation constants are reported.Solubility investigations were performed in NaCl aqueous solutions in a wide range of ionic strength (0.1 < I/mol L^− 1 < 3.0), with the aim to determine the activity coefficients of neutral species and the Setschenow coefficient of chitosan 310 kDa.     

One- and two-dimensional C–H/N–H dipolar correlation experiments under fast magic-angle spinning for determining the peptide dihedral angle φ

A recently proposed ¹³C–¹H recoupling sequence operative under fast magic-angle spinning (MAS) [K. Takegoshi, T. Terao, Solid State Nucl. Magn. Reson. 13 (1999) 203–212.] is applied to observe ¹³C–¹H and ¹⁵N–¹H dipolar powder patterns in the ¹H–¹⁵N–¹³C–¹H system of a peptide bond. Both patterns are correlated by ¹⁵N-to-¹³C cross polarization to observe one- or two-dimensional (1D or 2D) correlation spectra, which can be simulated by using a simple analytical expression to determine the H–N–C–H dihedral angle. The 1D and 2D experiments were applied to N-acetyl[1,2-¹³C,¹⁵N] -valine, and the peptide φ angle was determined with high precision by the 2D experiment to be ±155.0°±1.2°. The positive one is in good agreement with the X-ray value of 154°±5°. The 1D experiment provided the value of φ=±156.0°±0.8°.     

Electronic absorption in silicate mineral of copper

The electronic absorption spectrum of chrysocolla, a silicate mineral of copper, has been studied at room and liquid air temperatures. The observed bands were satisfactorily explained as belonging to Cu²⁺ ion subjected to tetragonal and spin-orbit fields. A good fit between the theoretical and observed band positions was obtained for the following crystal field parameters:Dq=–1400 cm^–1 Ds=–3000 cm^–1 Dt=–800 cm^–1 =–800 cm^–1     

Fourier transform emission spectroscopy of the TiF radical in the 407 nm region

Ultraviolet emission spectra of the TiF radical in the 407 nm region have been observed at a resolution of 0.04 cm⁻¹ using a Fourier transform spectrometer. A new electronic assignment of ⁴Γ–X⁴Φ has been proposed. Rotational analysis has been obtained for the 0–0 and 1–1 vibrational bands of the ⁴Γ_5/2–X⁴Φ_3/2, ⁴Γ_9/2–X⁴Φ_7/2, and ⁴Γ_11/2–X⁴Φ_9/2 subbands and the 0–0 band of ⁴Γ_7/2–X⁴Φ_5/2. The lower state rotational and centrifugal distortion constants are consistent with the previous results [J. Mol. Spectrosc. 184 (1997) 186; J. Chem. Phys. 119 (2003) 9496], to the conformation that the lower state of the 407 nm band is the ⁴Φ ground electronic state. Rough estimates of the vibrational interval ΔG(1/2) and the spin–orbit coupling constant A in the ⁴Γ state were also obtained.