快速合成廉价CuMo纳米粒子高效催化氨硼烷水解产氢

Noble-metal-free CuMo nanoparticles (NPs) without surfactant or support have been facilely prepared using NaBH₄ as a reducing agent. The as-prepared CuMo nanocatalysts were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), inductively coupled plasma-atomic emission spectroscopy (ICP-AES), X-ray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET) surface area measurements, and used as catalysts for the hydrolysis of ammonia borane (AB, NH₃BH₃) at room temperature. The as-synthesized Cu_0.9Mo_0.1 NPs exhibited a high activity towards the hydrolysis of AB with a turnover frequency (TOF) of 14.9 min^-1, a higher value than that reported for Cu catalysts. Our synthesis is not limited to CuMo NPs alone, but can easily be extended to CuW (3.6 min^-1), CuCr (2 min^-1), NiMo (55.6 min^-1), and CoMo (21.7 min^-1) NPs, providing a general approach to Cu-M (M = Mo, W, Cr) and TM-Mo (TM = Cu, Ni, Co) NPs as a series of novel catalysts for the hydrolysis of AB. The enhanced activity of bimetallic NPs may be attributed to the synergistic effects of the Cu-M NPs induced by the strain and ligand effects.     

原位合成钴/还原氧化石墨烯纳米粒子催化氨硼烷制氢

采用简单的原位还原合成方法,利用具有温和还原性能的氨硼烷作为还原剂,在室温下一步还原氧化石墨烯和氯化钴混合溶液制备了还原氧化石墨烯负载钴纳米复合材料催化剂. 利用所制备的钴/还原氧化石墨烯催化剂催化氨硼烷水解制氢,发现钴/还原氧化石墨烯具有优异的催化性能. 相对于没有负载的钴纳米粒子以及采用硼氢化钠作为还原剂制备的钴/还原氧化石墨烯催化剂,采用氨硼烷还原制备的钴/还原氧化石墨烯催化剂表现出更加优越的催化性能. 动力学测试表明,钴/还原氧化石墨烯催化氨硼烷水解反应为零级反应,同时钴/还原氧化石墨烯催化剂催化氨硼烷水解反应的活化能为27.10 kJ·mol^-1,低于大部分已报道的其它催化剂,甚至一些贵金属催化剂的活化能. 钴/还原氧化石墨烯催化剂有着稳定的循环使用性,特别是其具有的磁性使得它能够直接从溶液中通过磁力回收,极具应用前景. 这种简单有效的合成方法有望推广到其它的金属-还原氧化石墨烯纳米复合材料体系.     

Ruthenium deposited on MCM-41 as efficient catalyst for hydrolytic dehydrogenation of ammonia borane and methylamine borane

Ultrafine Ru nanoparticles are successfully deposited on MCM-41 by using a simple liquid impregnationreduction method, and further investigated for catalytic hydrolysis of ammonia borane and methylamine borane. Among all the catalysts tested, 1.12 wt% Ru/MCM-41 exhibits the highest catalytic activity, with turnover frequency value of 288 min^-1.     

SO_2对Mn-Ce/TiO_2低温SCR催化剂的毒化作用研究

考察了SO_2对Mn-Ce/TiO_2低温脱硝催化剂活性的影响,利用XRD、BET、SEM和XPS对其毒化作用的原因进行分析。结果表明,SO_2对催化剂活性有明显的抑制作用,使NO_x去除率由84%降至42%左右。主要是SO_2的加入造成催化剂比表面积减小,孔径为5-10 nm的孔数量减少,且催化剂晶相由锐钛矿型转化成金红石型结构,活性组分MnO_x发生晶化现象,破坏了Mn-Ti间的强相互作用。催化剂理化性质的变化造成吸附态氧转化为晶格氧的路径受阻、MnO_2含量减少和CeO_x储氧功能减弱,并且产生氧阻效应而使NO吸附和解吸受阻,造成催化剂活性降低。同时生成的硫酸铵盐在催化剂表面沉积,覆盖了催化剂表面的Lewis酸性位,使其对NH_3吸附能力减弱。     

CoOx-CeOx/ZrO2催化氧化NO性能及抗SO2毒化研究

采用浸渍法制备了一系列CoO_x-CeO_x/ZrO₂催化剂,探讨了催化剂载体、Co含量、Co/Ce配比等对Co基催化剂催化氧化NO活性的影响及其机理。ZrO₂负载的Co氧化物具有优良的低温NO催化氧化活性,铈的添加进一步提高了催化剂的低温活性。其促进机制主要是提高了催化剂吸附氧的能力及改善了Co在催化剂表面的分散。同时,掺杂铈使得催化剂抗SO₂能力有一定增强,呈现出选择性毒化机制。     

改性ZrO2负载钌氨合成催化剂的制备及其构效关系研究

由ZrO(NO₃)₂水解得到的ZrO(OH)₂水凝胶经碱液回流老化、焙烧后制备了改性ZrO₂载体材料,直接浸渍K₂RuO₄溶液,经还原后用于催化氨合成反应。并运用X射线衍射(XRD)、CO₂ 程序升温脱附(CO₂-TPD)、X射线荧光光谱 (XRF)、N₂物理吸附、H₂程序升温还原技术(H₂-TPR)和CO化学吸附对其进行了表征,重点考察了催化剂性能与载体性能间的构效关系。结果表明,KOH和NH₄OH溶液回流均可提高载体的比表面积,但是KOH回流制备的载体同时还具有较强的碱性,因此,负载钌以后表现出最佳活性。在425 ℃、5 MPa、空速为10 000 h^-1条件下,出口氨浓度为5.96%,分别较催化剂K-Ru/ZrO₂-NH₄OH、K-Ru/ZrO₂-CP和Ru/ZrO₂-NH₄OH提高了11%、143%和103%。与活性组分分散度相比,载体碱性强度对活性的促进作用更为明显。     

Zn-Co bimetallic supported ZSM-5 catalyst for phosgene-free synthesis of hexamethylene–1,6–diisocyanate by thermal decomposition of hexamethylene–1,6–dicarbamate

A set of mono-and bimetallic(Zn-Co) supported ZSM-5 catalysts was first prepared by PEG-additive method. The physicochemical properties of the catalysts were investigated by FTIR, XPS, XRD, N_2adsorption-desorption measurements, SEM, EDS and NH3-TPD techniques. The physicochemical properties showed that the Zn Co_2O_4 spinel oxide was formed on the ZSM-5 support and provided effectual synergetic effect between Zn and Co species for the bimetallic catalyst. Furthermore, bimetallic supported ZSM-5 catalyst exhibited weak, moderate and strong acidic sites, while the monometallic supported ZSM-5 catalyst showed only weak and moderate or strong acidic sites. Their catalytic performances for thermal decomposition of hexamethylene–1,6–dicarbamate(HDC) to hexamethylene–1,6–diisocyanate(HDI) were then studied. It was found that the bimetallic supported ZSM-5 catalysts,especially Zn-2Co/ZSM-5 catalyst showed excellent catalytic performance due to the good synergetic effect between Co and Zn species, which provided a suitable contribution of acidic sites. HDC conversion of 100% with HDI selectivity of 91.2% and by-products selectivity of 1.3% could be achieved within short reaction time of 2.5 h over Zn-2Co/ZSM-5 catalyst.     

Defect‐Rich Co−CoOx‐Graphene Nanocatalysts for Efficient Hydrogen Production from Ammonia Borane

Chemical hydrogen storage ammonia borane has attracted extensive attention as a method of efficient utilization of hydrogen energy. The high‐efficiency catalysts are the main factor restricting the hydrogen production of ammonia borane. In this paper, the synergistic effect of Co and CoO_x supported on graphene (named Co?CoO_x@GO‐II) promotes the efficient hydrogen production of ammonia borane, and its catalytic hydrogen production rate can reach 5813 mL min^?1 g_Co^?1 at 298 K, the corresponding TOF is 15.33 min^?1. After five stability tests, Co?CoO_x @GO‐II maintained 65% of its original catalytic performance. The synergy of metal and metal oxide and the defects in the atomic arrangement ensure the catalytic activity, the large specific surface area of graphene ensures the dispersion and fixation. This strategy may provide a possibility to design high‐performance transition metal catalysts.     

Co-B/γ-Al2O3非晶态催化剂的制备及其催化乳酸乙酯液相加氢性能

采用浸渍-还原法制备了负载型Co-B/γ-Al₂O₃非晶态合金催化剂, 并将其应用于乳酸乙酯液相加氢制备1,2-丙二醇(1,2-PDO)反应中, 研究了其催化加氢性能. 采用电感耦合等离子体(ICP)发射光谱仪、X射线衍射(XRD)仪、透射电子显微镜(TEM)、差示扫描量热(DSC)、X射线光电子能谱(XPS)等手段对催化剂的性能进行了表征, 考察了制备条件对催化剂性能的影响. 结果表明, 新鲜的Co-B/γ-Al₂O₃催化剂具有非晶态结构, Co-B均匀地分散在载体γ-Al₂O₃上. 随着Co负载量的增加, 催化剂的热稳定性提高, 催化剂表面Co/B原子比增加. 当金属Co理论负载量为30%(质量分数, w)时, Co-B/γ-Al₂O₃催化剂表现出最高的加氢催化性能, 在160 ℃, 氢气压力为6.0 MPa条件下反应9 h, 乳酸乙酯的转化频率(TOF)为1.41 h^-1, 转化率达到93.63%, 1,2-丙二醇的选择性达到96.10%. 催化剂的加氢性能取决于其分散均匀的Co-B纳米粒子、较高的表面Co/B原子比及Co和B之间的电子转移效应.     

Cu-Co负载量对Cu-Co基催化剂催化CH4-合成气梯阶转化合成C2+含氧化合物的影响

以TiO₂纳米粒子为载体, 采用等体积浸渍法制备了Cu-Co双金属催化剂, 考察了不同Cu/Co质量比和不同Cu-Co含量的双金属催化剂对CH₄-合成气梯阶转化直接合成C₂⁺含氧化合物的影响. 在连续式步阶固定床反应装置上进行了催化性能评价. 实验结果表明, 当Cu-Co含量为18%, Cu/Co质量比为2: 1时, Cu-Co/TiO₂的C₂⁺含氧化合物产物的时空收率最大, 为19.92 mg·g_cat^-1·h^-1, 选择性为67.76%. 研究表明, 金属组分之间和载体与金属组分之间的相互作用、 金属组分良好的分散性和还原性是促进活性位的形成和提高催化剂活性的原因; 催化剂表面高度分散的CuO微晶有利于催化加氢和脱氢反应的进行, 对CH₄-合成气转化反应有重要的促进作用. 另外, 弱酸和中强酸有利于CH₄-合成气转化反应, 而强酸对该反应有抑制作用.     

钾改性氧化铝基羰基硫水解催化剂及其失活机理

天然气、油田伴生气、高炉煤气等化工生产过程中伴生COS气体,不仅会腐蚀管道和毒害催化剂,还会严重污染环境并危害人类健康。COS催化水解反应可在温和条件下高效的将COS脱除,是最具应用前景的COS脱除技术之一。碱金属元素因其具有独特的电子供体性质、表面碱性和静电吸附等特性,常被用作助催化剂以提高Al₂O₃的COS催化水解性能。近年来,以钾为助剂改性的Al₂O₃催化剂(K₂CO₃/Al₂O₃)在COS催化水解反应中得到广泛的应用,但由于负载在Al₂O₃上的K物种的组成复杂,目前研究者对K₂CO₃/Al₂O₃催化剂上COS水解机理的理解仍存在一定的困惑和争议。本论文通过湿法浸渍法合成出一系列钾盐和钠盐改性的Al₂O₃催化剂,并利用各类先进的表征技术对这些催化剂进行分析。活性测试表明,以K₂CO₃、K₂C₂O₄、NaHCO₃、Na₂CO₃和NaC₂O₄改性Al₂O₃催化剂均有助于COS的水解。其中K₂CO₃/Al₂O₃拥有最佳的COS水解性能,连续运行20 h后其COS转化率仍高于~93%,远远优于未改性的Al₂O₃ (~58%)。我们利用原位红外光谱和X射线光电子能谱探明了反应过程中催化剂的化学结构特征,阐明了H₂O分子在K₂CO₃/Al₂O₃上的水解作用机制。原位红外表明COS在K₂CO₃/Al₂O₃上的水解过程中形成了硫代碳酸氢盐中间产物。X射线光电子能谱表征证明催化剂的失活主要是因为催化剂表面积累了硫酸盐和单质硫。此外,我们还研究了水蒸气含量对COS水解性能的影响,研究发现,由于H₂O和COS分子在催化剂表面存在竞争吸附,过量的H₂O会引起催化活性的下降。上述研究表明,K₂CO₃/Al₂O₃催化剂上COS水解性能的提高主要是形成了HO-Al-O-K界面活性位。更为重要的是,所制备的催化剂都是在模拟工业工况条件下进行的,这为后续的工业应用提供了宝贵理论指导。本工作为理解助剂钾在Al₂O₃催化剂上COS水解活性的增强提供了新的见解,这为未来设计稳定高效的COS水解催化剂打开了新的发展方向。     

蒸氨压力对Cu/SiO_2催化剂的影响及其草酸二甲酯加氢性能

以Si O2为载体,铜氨溶液为前驱体,采用蒸氨法在不同蒸氨压力下制备了系列铜负载量质量分数为20.0%的Cu/Si O2催化剂。采用X射线衍射(XRD)、H2-程序升温还(H2-TPR)、高分辨透射电子显微镜(HRTEM)、X射线诱导俄歇电子能谱(XAES)等技术手段对催化剂的物理化学性能进行了表征。考察了蒸氨速率对催化剂物化结构及其草酸二甲酯催化加氢制乙二醇的催化性能影响。在反应温度200℃、压力3.0 MPa、液时空速LHSV=0.4 h-1、氢气草酸二甲酯摩尔比80∶1的反应条件下测定了催化剂的活性。结果表明,在蒸氨压力为31.3 k Pa条件下制备的催化剂表现出了最佳活性和选择性,草酸二甲酯转化率达到了99.9%,乙二醇选择性达94.4%。H2-TPR、XRD、TEM、FTIR及XAES表征结果表明,较低蒸氨压力有利于铜氨离子快速分解负载在载体上,避免铜粒子聚集长大,还原后形成Cu2O和Cu0物种颗粒尺寸较小,分散比较均匀,催化活性,尤其是乙二醇的选择性更佳。     

Al2O3助剂对Co/SiC催化剂F-T反应性能的影响

分别采用沉淀法、尿素水解法制备Al₂O₃/SiC复合载体,采用等体积浸渍法制备Co/Al₂O₃-SiC催化剂。结合N₂吸附、XRD、H₂-TPR、XPS等表征手段,研究Al₂O₃助剂对钴基催化剂物相结构、还原行为以及F-T合成性能等的影响。结果表明,氧化铝加入后增强了载体与钴物种之间的相互作用,提高了钴物种的分散度,降低了钴物种的还原度。尿素水解法引入Al₂O₃后,载体与钴物种具有适中的相互作用,表现出较高的反应活性。沉淀法制备的载体负载钴物种后由于较强的金属-载体相互作用,表现出较优的稳定性。     

CeOx doping on a TiO2-SiO2 supporter enhances Ag based adsorptive desulfurization for diesel

In this work, the impact of CeO_x doping on a TiO₂-SiO₂ supporter on the Ag based adsorptive desulfurization for Chinese standard diesel was studied. The dispersion and valence states of Ce, Ti and Ag species were characterized, and the impact of Ce doping was investigated. The results indicated that Ce species and Ti species were dispersed evenly on the surface of SiO₂ via a novel co-impregnation method. Following CeO_x doping, the Ag species were in the form of oxides (about 5nm) instead of metallic Ag particles (about 35nm), which is due to the large amount of coordinative unsaturated sites provided by the interaction between CeO_x and TiO₂, as well as the oxidation-reduction property of CeO_x. The Ag in the active oxide state (Ag₂O₂) and dispersed evenly on the supporter could interact with sulfur compounds more favorably, and therefore showed a good performance in the adsorptive desulfurization. In both static batch and dynamic breakthrough desulfurization tests, Ag-CeO_x/TiO₂-SiO₂ was proved to be a more efficient adsorbent compared with Ag-TiO₂-SiO₂. It was found that the desulfurization performance of Ag-TiO₂-SiO₂ exhibited an excellent improvement (22.5%) after being doped with CeO_x. In the static equilibrium tests, the equilibrium sulfur capacity of Ag-CeO_x/TiO₂-SiO₂ was up to 5.38mg/g for CN-II diesel (sulfur content 952.9mg/kg) and the sulfur content of the CN-IV diesel (sulfur content 39.0mg/kg) after desulfurization was less than 10mg/kg, which could meet the CN-V standard.     

催化氨硼烷水解制氢研究进展

当前,世界范围内的能源利用面临着巨大的挑战,开发绿色洁净能源十分重要。通过水解氨硼烷制备清洁可再生的氢气是解决能源问题的有效途径之一。选择合适的催化剂有效提高制氢效率是氨硼烷水解制氢的关键,开发高效安全的催化剂一直是该领域研究的重点和热点。本文从影响氨硼烷水解制氢反应中催化剂催化性能的因素出发,综述了活性金属组分和载体在催化剂制备过程中以及催化氨硼烷制氢反应中的作用。最后,对催化氨硼烷水解制氢过程所存在的问题以及今后的发展进行了总结和展望。     

氨浓度对氨蒸发法制备Pd-Cu/凹凸棒土催化剂常温CO氧化性能的影响

以凹凸棒土(APT)作载体,采用氨蒸发法制备了Pd-Cu/APT催化剂,以CO氧化为探针反应,在连续流动微反应装置上,考察了初始氨浓度对催化剂CO常温催化氧化性能的影响。通过N₂-physisorption、XRD、FT-IR、TEM和H₂-TPR等手段对催化剂的结构和性质进行了表征。结果表明,在较低或过高氨浓度条件下,制备的Pd-Cu/APT中Cu物种均主要以CuO为主,仅有少量Cu₂(OH)₃Cl;适宜的氨浓度有利于稳定Cu₂(OH)₃Cl物相的形成,其薄片状的形貌特征、良好的分散状态以及与Pd物种间较强的相互作用,显著提高了CO催化氧化性能。在空速6 000 h^-1、CO体积分数1.5%、水蒸气体积分数3.3%的反应条件下,Pd-Cu/APT催化剂表现出优异的CO室温催化氧化活性和稳定性。     

不同硅源的Cu/SiO2催化糠醛加氢制2-甲基呋喃

以硅溶胶和气相二氧化硅为载体,采用氨蒸法制备了Cu/SiO₂-sol和Cu/SiO₂-aer两种催化剂,采用N₂吸附脱附、X射线衍射（XRD）、傅里叶红外光谱（FT-IR）、透射电子显微镜（TEM）、N₂O-H₂滴定、氢气程序升温还原（H₂-TPR）、氨程序升温脱附（NH₃-TPD）及X射线光电子能谱（XPS）对样品进行表征,在固定床反应器中考察两种催化剂对糠醛气相加氢制2-甲基呋喃的催化性能。结果表明,Cu/SiO₂-sol催化剂具有更好的催化活性,在150 h反应时间内,糠醛转化率为100%,2-MF选择性在91%以上。这主要归因于以硅溶胶为硅源可以生成更多页硅酸铜,还原后催化剂表面Cu的分散性更高、弱酸位更多,有利于提高糠醛的转化率与2-甲基呋喃的选择性。同时Cu/SiO₂-sol具有较大的孔容孔径,有利于降低反应过程中积炭,延长催化剂寿命。     

Ru添加对Co/SiO2费托合成催化剂性能的影响

用初湿含浸法制备了不同Ru添加量的Co/SiO₂模型催化剂,然后进行N₂物理吸附、XRD、H₂-TPD、DRIFTS等表征和微分固定床费托(F-T)反应评价。F-T反应结果表明,催化剂中添加Ru后,CO转化率显著提高,TOF值增大,CO₂和CH₄选择性降低,烯/烷比(O/P)降低。FT-IR表征说明,催化剂添加Ru后Co-O键的强度减弱,相对应的H₂-TPR也表明,催化剂的还原度得到显著提高。还原后的催化剂XRD结果进一步证实,加入Ru后,催化剂无钴氧化物被检出,并且当Ru添加量为0.5%(质量分数)时催化剂中金属钴主要以六方密堆(hcp)形式存在。CO-DRIFTS结果显示,Ru的加入使CO的吸收峰发生红移,即Ru促进了CO的解离。H₂-TPD结果则表明,随着Ru添加量的增加,催化剂表面CO_ads/Co_s和CO^*/Co_s增大,这是CH₄选择性降低的主要原因。     

分子筛USY负载硼化钴非晶态合金催化剂的制备及其在催化硼氢化钠水解制氢中的应用

采用浸渍法与化学还原法相结合制备了一系列USY型分子筛负载非晶态合金硼化钴(CoB/USY)催化剂,并系统探究了该催化剂在催化硼氢化钠水解制氢中的催化活性。 XRD表征表明,USY分子筛载体上负载的活性组分CoB属于非晶态结构。 通过扫描电子显微镜,对比了负载型CoB/USY催化剂和粉末状CoB催化剂的微观形貌,发现非晶态合金活性组分CoB能够很好的分布在USY分子筛载体表面,较粉末状CoB有更高的分散度。 催化硼氢化钠水解制氢实验结果表明,相对于粉末状CoB催化剂,负载型CoB/USY催化剂在硼氢化钠水解制氢中具有更高的催化活性,30 ℃时NaBH₄水解产氢速率约为1.5 L/(min·g)。 反应动力学的计算结果显示,负载型CoB/USY催化剂在催化NaBH₄水解制氢反应中表观活化能约为65.9 kJ/mol,大大低于粉末状CoB催化剂的活化能(72.1 kJ/mol)。     

Zirconia supported La, Co oxides and LaCoO3 perovskite: structural characterization and catalytic CO oxidation

ZrO₂-supported La, Co oxide catalysts with different La, Co loading (2, 6, 8, 12 and 16 wt.% as LaCoO₃) were prepared by impregnation of tetragonal ZrO₂ with equimolar amounts of La and Co citrate precursors and calcination at 1073 K. The catalysts were characterized by X-ray diffraction (XRD), X-ray absorption spectroscopy (XAS), and BET specific surface area determination. Catalytic CO oxidation was performed at 298–800 K. XRD revealed the presence of tetragonal zirconia with traces of the monoclinic phase. LaCoO₃ perovskite was also detected for loading higher than 6%. XAS experiments suggested that at high loading LaCoO₃ and Co₃O₄ were formed, while at low loading, La, Co oxide species interacting with support, and hard to be structurally defined, prevailed. The catalysis study evidenced that the catalytic activity was due to segregated and highly dispersed cobalt oxide species.