Vermiculite clay mineral as an effective carbon paste electrode modifier for the preconcentration and voltammetric determination of Hg(II) and Ag(I) ions

A vermiculite modified carbon paste electrode (VMCPE) was employed for the in situ preconcentration of traces of Hg(II) and Ag(I) via an ion-exchange route. Heavy metal ions were accumulated in Britton-Robinson (BR) buffer pH 7 for Hg(II) and pH 6 for Ag(I), and afterwards reduced at –0.7 V vs. Ag/AgCl in the separate measurement solution (BR buffer pH 5 + 0.05 mol/L NaNO₃) prior to the anodic stripping square-wave voltammetric (ASSWV) detection. For Hg(II) ions, at 15 min accumulation, a linear range from 1.0 × 10^–7 to 8.0 × 10^–6 mol/L was obtained, with a 5.7 × 10^–8 mol/L limit of detection. The VMCPE response was linear for Ag(I) ions in the concentration range from 2.0 × 10^–7 to 8.0 × 10^–6 mol/L, at 10 min accumulation with a corresponding limit of detection of 6.3 × 10^–8 mol/L. The relative standard deviation of the analytical procedure including accumulation from a 5 × 10^–7 mol/L solution of Hg (15 min) or Ag(I) (10 min), electrolysis, ASSWV detection, regeneration and activation of the VMCPE, was 4% (n = 6). The optimisation of the parameters for the application of the VMCPE in combination with ASSWV detection is presented and discussed. Received: 10 July 1997 / Revised: 31 October 1997 / Accepted: 3 November 1997     

Determination of traces of purine by cathodic stripping voltammetry at the hanging copper amalgam drop electrode

In the presence of purine, the copper(II)/copper(Hg) couple splits into copper(II)/copper(I) and copper(I)/copper(Hg) couples, which form two well-separated systems of peaks under voltammetric conditions. The copper(I)/purine complex adsorbs on the electrode surfacer and can be deposited on the electrode surface by electroreduction of copper(II) ions at the HMDE or by electro-oxidation of the hanging copper amalgam drop electrode (HCADE). The deposit can be stripped either cathodically or anodically over the pH range 2–9. The cathodic stripping variant at the HCADE, in solution with pH 2, offers the best results, with linear response for the range 5 × 10^?9–1.5 × 10^?7 mol dm^?3 purine after an accumulation time of 3 min. The detection limit found with the HMDE in the presence of copper(II) ions is higher.     

Catalytic Adsorptive Stripping Voltammetry of Germanium(IV) in the Presence of Gallic Acid and Vanadium(IV)‐EDTA

A highly sensitive and selective catalytic adsorptive cathodic striping procedure for the determination of trace germanium is presented. The method is based on adsorptive accumulation of the Ge(IV)‐gallic acid (GA) complex onto a hanging mercury drop electrode, followed by reduction of the adsorbed species. The reduction current is enhanced catalytically by addition of vanadium(IV)‐EDTA. The optimal experimental conditions include the use of 0.03 mol/L HClO₄ (pH1.6), 6.0×10^?3 mol/L GA, 3.0×10^?3 mol/L V(IV), 4.0×10^?3 mol/L EDTA, an accumulation potential of ?0.10 V(vs. Ag/AgCl), an accumulation time of 120 s and a differential pulse potential scan mode. The peak current is proportional to the concentration of Ge(IV) over the range of 3.0×10^?11 to 1.0×10^?8 mol/L and the detection limit is 2×10^?11 mol/L for a 120 s adsorption time. The relative standard deviation at 5.0×10^?10 mol/L level is 3.1%. No serious interferences were found. The method was applied to the determination of germanium in ore, mineral water and vegetable samples with satisfactory results.     

Determination of idarubicin in human urine by capillary zone electrophoresis with amperometric detection

A simple, reliable and reproducible method, based on capillary zone electrophoresis with amperometric detection, has been developed for the determination of idarubicin in human urine. A carbon disk electrode was used as working electrode. The optimal conditions of separation and detection were pH 5.6 phosphate buffer ¶(0.20 mol/L), 22 kV for the separation voltage and 1.00 V (vs. Ag/AgCl, 3 mol/L KCl) for the detection potential. The linear range was from 4.0 × 10^–7 to 2.0 × 10^–5 mol/L with a regression coefficient of 0.9986, and the detection limit was 8.0 × 10^–8 mol/L. The method was directly applied to the determination of idarubicin in spiked human urine without any other sample pretreatment except filtration, and the assay results were satisfactory.     

Determination of mercury(II) by surface-enhanced Raman scattering spectroscopy based on thiol-functionalized silver nanoparticles

Silver nanoparticles (Ag NPs) modified with sodium 2-mercaptoethanesulfonate (mesna) exhibit strong surface-enhanced Raman scattering (SERS). Their specific and strong interaction with heavy metal ions led to a label-free assay for Hg(II). The covalent bond formed between mercury and sulfur is stronger than the one between silver and sulfur and thus prevents the adsorption of mesna on the surface of Ag NPs. This results in a decrease of the intensity of SERS in the presence of Hg(II) ions. The Raman peak at 795?cm^?1 can be used for quantification. The effect of the concentration of mesna, the concentration of sodium chloride, incubation time and pH value on SERS were optimized. Under the optimal conditions, the intensity of SERS decreases with increasing concentration of Hg(II). The decrease is linear in the 0.01 and 2?μmol L^?1 concentration range, with a correlation coefficient (R²) of 0.996 and detection limit (S/N?=?3) is 0.0024?μmol L^?1. The method was successfully applied to the determination of the Hg(II) in spiked water samples.

Cathodic and anodic stripping determination of traces of adenine and adenosine based on accumulation of copper(I) compounds at mercury or amalgam electrodes

In the presence of adenine and adenosine, the copper(II)/copper(Hg) couple splits to the copper(II)/copper(I) and copper(I)/copper(Hg) couples. Sparingly soluble complexes of copper(I) with adenine and adenosine can be accumulated on the electrode surface either by reduction of Cu(II) ions or by oxidation of the copper amalgam electrode. The copper(I)/adenine deposit can be stripped either cathodically or anodically with detection limits of 5×10^?9 and 2×10^?8 mol dm^?3, respectively. The copper(I)/ adenosine complex yields only the cathodic stripping peak with a detection limit of 9×10^?6 mol dm^?3. The stripping peaks obtained for the copper(I)/adenine and copper(I)/ adenosine complexes are better defined and appear over a wider range of pH than the peaks related to the corresponding mercury compounds. Adenosine cannot be determined in the presence of adenine bur adenine can be determined in the presence of moderate amounts of adenosine.     

Development of Pr(III) Selective Electrode Using 1,6,7,12‐Tetramine‐2,5,8,11‐tetraoxo‐1(12),6(7)‐di(biphenyl)‐dodecane (TATODBDD) as a Neutral Carrier

A polyvinyl chloride (PVC) membrane based Pr(III) selective electrode was constructed using 1,6,7,12‐tetramine‐2,5,8,11‐tetraoxo‐1(12),6(7)‐di(biphenyl)dodecane (TATODBDD) as a neutral carrier. The sensor exhibits a Nernstian response for Pr(III) ions, a wide concentration range of 3.9×10^?7?1.0×10^?1 mol/L with a detection limit of 5.0×10^?8 mol/L and slope of 19.5 mV/decade. The developed sensor revealed relatively good selectivity and high sensitivity for Pr(III) ions over the other lanthanide ions. The potentiometric response of the sensor is independent in the pH range 2.9–9.5. The advantages of sensor are low resistance, very fast response time (<10 s) with good selectivity. This sensor can be used up to 6 weeks without any divergences in potential response.     

One‐Step Synthesis of β‐Cyclodextrin Functionalized Graphene/Ag Nanocomposite and Its Application in Sensitive Determination of 4‐Nitrophenol

β‐Cyclodextrin functionalized graphene/Ag nanocomposite (β‐CD/GN/Ag) was prepared via a one‐step microwave treatment of a mixture of graphene oxide and AgNO₃. β‐CD/GN/Ag was employed as an enhanced element for the sensitive determination of 4‐nitrophenol. A wide linear response to 4‐nitrophenol in the concentration ranges of 1.0×10^?8–1.0×10^?7 mol/L, and 1.0×10^?7–1.5×10^?3 mol/L was achieved, with a low detection limit of 8.9×10^?10 mol/L (S/N=3). The mechanism and the heterogeneous electron transfer kinetics of the 4‐nitrophenol reduction were discussed according to the rotating disk electrode experiments. Furthermore, the sensing platform has been applied to the determination of 4‐nitrophenol in real samples.     

A new PVC matrix membrane sensor for determination of praseodymium(III) ion based on bis(salicylaldehyde)thiocarbohydrazone as an ion carrier

The sufficient amounts of bis(salicylaldehyde) thiocarbohydrazone (STCH) as a lipophilic selective element (3%, w/w), sodium nitrobenzene (NB) as a plasticizer (64%, w/w), tetraphenyl borate (NaTPB) as an anionic additive (3%, w/w), and poly vinyl chloride (PVC) as a polymeric matrix (30%, w/w) was employed to form a PVC membrane of a new Pr³⁺ ions selective sensor to apply as an indicator electrode in analytical applications. The best electrode response was observed in the slope (19.5 ± 0.7 mV per decade) over a wide concentrations from lower (1.0 × 10^?6 mol L^–1) to higher (1.0 × 10^?2 mol L^–1) of Pr³⁺ ion solution with a detection limit of 8.5 × 10^–7 mol L^–1. This electrode showed the fast response time about 10 second for praseodymium ion concentration range of 1.0 × 10^–6 to 1.0 × 10^–2 mol L^–1, in the pH range of 2.3–7.9. The matched potential method was applied to study the selectivity of electrode toward Pr³⁺ ions in comparison with many common cations. The results showed the negligible disturbance of all other cations on the proposed praseodymium(III) electrode. The making sensor has been employed successfully as an indicator electrode in the potentiometric titration of praseodymium(III) solution with EDTA at pH 6.0. Moreover the applicability of the sensor was studied in determination of Pr³⁺ ion in mixtures of different ions.     

Anodic Stripping Voltammetric Determination of Lead（Ⅱ） Using Glassy Carbon Electrode Modified with Novel Calix[4] arene

A new glassy carbon electrode modified with novel calix[4]‐arene derivative was prepared and then applied to the selective recognition of lead ion in aqueous media by cyclic and square wave voltammetry. A new anodic stripping peak at ? 0.92 V (vs. Ag/Ag⁺) in square wave voltammogram can be obtained by scanning the potential from ? 1.5 to ? 0.6 V, of which the peak current is proportional to the concentration of Pb²⁺. The modified electrode in 0.1 mol/L HNO₃ solution showed a linear voltammetric response in the range of 2.0 × 10–⁸–1.0 × 10–⁶ mol/L and a detection limit of 6.1 × 10–⁹ mol/L. In the modified glassy carbon electrode no significant interference occurred from alkali, alkaline and transition metal ions except Hg²⁺, Ag⁺ and Cu²⁺ ions, which can be eliminated by the addition of KSCN. The proposed method was successfully applied to determine lead in aqueous samples.     

Thiol‐Functionalized Silica Thin Film Modified Electrode in Determination of Mercury Ions in Natural Water

The use of a thin thiol‐functionalized silica film modified glassy carbon electrode in the determination of Hg(II) ions in a natural water sample is described. A typical measurement involves two successive steps: a glassy carbon electrode coated with a thin mesoporous silica film containing 10% of mercaptopropyl groups, according to the MPTMS/TEOS ratio in the starting sol‐gel, was first immersed into the accumulation medium for 15 min, then removed, and finally transferred into a detection solution containing KCl 1.0 mol L^?1 where detection was performed by anodic stripping voltammetry. In this medium the previously accumulated Hg²⁺ species complexed by the thiol groups in an open circuit preconcentration step is then directly reduced at ?0.6 V during 60 s prior to be quantified by a differential pulse anodic scan from ?0.6 to 0.3 V (vs. Ag/AgCl). A stripping peak appeared at about ?0.01 V, which is directly proportional to the quantity of the analyte previously accumulated into the film. The best results were obtained under the following conditions: 100 mV pulse amplitude and 10 mV s^?1 scan rate in 1.0 mol L^?1 KCl solution pH 2.0. Using such parameters a linear dynamic range from 1.00 to 10.0×10^?8 mol L^?1 Hg(II) was observed with a limit of detection of 4.3 nmol L^?1 for an accumulation time of 15 min. Hg(II) spiked in a natural water sample was determined between 97.0 and 101.4% mean recovery at 10^?8 mol L^?1 level. The results indicate that this electrode is sensitive and selective for the Hg(II)determination.     

Liquid-state mercury(II) ion-selective electrode based on N-(O,O-diisopropylthiophosphoryl)thiobenzamide

A liquid ion-exchange electrode containing a complex of mercury(II) with N-(O,O-diisopropylthiophosphoryl)thiobenzamide in carbon tetrachloride is described. The electrode shows excellent sensitivity and good selectivity. The slope of the calibration graph is 29.0 mV/pHg²⁺ in the pHg²⁺ in the pHg²⁺ range 2–15.2 in mercury(II) ion buffers. The electrode can be used for determination of 5 × 10^?5–10^?2 M Hg(II) in the presence of 10^?2 M Cu(II), Ni(II), Co(II), Zn(II), Pb(II), Cd(II), Mn(II), Fe(III), Cr(III), Bi(III) or Al(III) ions and in the presence of 10^?3 M Ag(I) ions. It can bealso used for end-point detection in titrations with EDTA of 10^?3–10^?4 M mercury(II) at pH 2.     

Microwave-radiated synthesis of gold nanoparticles/carbon nanotubes composites and its application to voltammetric detection of trace mercury(II)

Gold nanoparticles/carbon nanotubes (Au-NPs/CNTs) composites were rapidly synthesized by microwave radiation, and firstly applied for the determination of trace mercury(II) by anodic stripping voltammetry (ASV). The structure and composition of the synthesized Au-NPs/CNTs nanocomposites were characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), UV–vis absorption spectroscopy and cyclic voltammetry. Au-NPs/CNTs nanocomposites modified glassy carbon electrode (Au-NPs/CNTs/GCE) exhibited excellent performance for Hg(II) analysis. A wide linear range (5 × 10⁻¹⁰–1.25 × 10⁻⁶ mol/L) and good repeatability (relative standard deviation of 1.84%) were obtained for Hg(II) detection. The limit of detection was found to be 3 × 10⁻¹⁰ mol/L (0.06 μg/L) at 2 min accumulation, while the World Health Organization’s guideline value of mercury for drinking water is 1 μg/L, suggesting the proposed method may have practical utility.     

Chemiluminescence flow system for the determination of sulfite

A novel chemiluminescence(CL) flow system for sulfite is described based on electrostatically immobilized luminol on an anion exchange column. Sulfite is detected by the CL reaction with luminol bleeding from the column by hydrolysis. The calibration graph is linear in the range 3 × 10^–7 to 1 × 10^–5 mol/L, and the detection limit is 1 × 10^–7 mol/L. Interfering metal ions co-existing in sample solutions could be effectively eliminated on-line by an upstream cation exchanger. A complete analysis could be performed in 1 min with a relative standard deviation of less than 5%. The system could be reused for over 50 h and has been applied successfully to the determination of sulfur dioxide in air.     

Anodic Stripping Voltammetric Determination of Mercury in Water Using a Chitosan‐Modified Carbon Paste Electrode

Abstract

This paper describes the preparation and electrochemical application of a modified carbon paste electrode with chitosan for the determination of Hg(II) ions in water using anodic stripping voltammetry. Experimental parameters, including the pH of the supporting electrolyte, time and potential of accumulation and scan rate were investigated. The best voltammetric response was observed for a paste composition of 60% (m/m) of graphite powder, 20% (m/m) of chitosan and 20% (m/m) of mineral oil, with 0.1 mol/l NaNO₃ solution at pH 6.3 as supporting electrolyte, a preconcentration potential of ?0.2 V, preconcentration time of 270 s and a scan rate of 25 mV/s. Under these optimal experimental conditions, the voltammetric signals were linearly dependent on the Hg(II) concentration in the range of 9.99×10^?7 to 3.85×10^?5 mol/l with a detection limit of 6.28×10^?7 mol/l. Three “spiked” samples of water were evaluated using the proposed sensor, and results agreed with those obtained by a reference method at the 95% confidence level.     

Comparative Study on Electroanalysis of Fenthion Using Silver Amalgam Film Electrode and Glassy Carbon Electrode Modified with Reduced Graphene Oxide

Oxidation and reduction processes of the insecticide fenthion was comparatively investigated at a reduced graphene oxide modified glassy carbon electrode (RGO‐GCE) and a cyclic renewable silver amalgam film electrode (Hg(Ag)FE) using square wave stripping voltammetry (SWSV). The influence of pH and SW parameters was investigated. The linear concentration ranges were found to be 1 × 10⁻⁶ – 2 × 10⁻⁵ and 1 × 10⁻⁷ – 2 × 10⁻⁵ mol L⁻¹ for Hg(Ag)FE and RGO‐GCE, respectively. The detection and quantification limits were calculated as 1.3 × 10⁻⁷ and 4.5 × 10⁻⁷ mol L⁻¹ for Hg(Ag)FE and 7.6 × 10⁻⁹ and 2.5 × 10⁻⁸ mol L⁻¹ for RGO‐GCE. Both of the developed electroanalytical methods offer rapid and simple detection of fenthion and were used on spiked tap and river water and apple juice samples. Scanning electron microscopy was used for RGO‐GCE surface characterization.     

Chemiluminescence determination of sulfite in sugar and of sulfur dioxide in air using the tris(2,2′-bipyridyl)ruthenium-KIO4 system

The chemiluminescence (CL) detection for the determination of sulfite using the reaction of Ru(bipy)₃ ²⁺(bipy=2,2′-bipyridyl)-SO₃ ^2–-KIO₄ is described. The concentration of sulfite is proportional to the CL intensity from 1.0 × 10^–7 to 1.0 × 10^–4 mol/L. The limit of detection is 2.0 × 10^–8 mol/L and the relative standard deviation is 4.4% for a 2 × 10^–5 mol/L sulfite solution (n = 9). This method has successfully been applied to the determination of sulfite in powdered sugar (sucrose) and of sulfur dioxide in air by using triethanolamine (TEA) as absorbent material.     

Preconcentration and electroanalysis of silver at pt electrode modified with poly(2-aminothiazole)

Conducting poly(2-aminothiazole) (PAT) films were electrodeposited on a platinum disc electrode surface by constant potential electrolysis of 2-aminothiazole (AT) for the stripping voltammetric determination of Ag(I). Ag(I) was preconcentrated on the polymer matrix by dipping the modified Pt electrode (PAT-Pt electrode) into Ag(I)(aq) solution. Effects of the film thickness, reduction potential, pH, preconcentration time, Ag(I) concentration and the interference of some other metal ions on the oxidation peak current of silver were studied. Cu(II) interference observed to be significant for the stripping voltammetric determination of Ag(I). The detection limit was calculated on the basis of signal to noise ratio of 3 as 2 × 10^?7 mol L^?1.     

Studies on Polarographic Adsorptive Wave of the System of the Rare Earth (III)-Copper(Ii)-M-Trifluomethyl Chlorophosphonazo

Abstract

A new heteronuclear complex, rare earth (III)-copper (II)-m-trifluomethyl chlorophosphonazo (CPA-mCF₃) system for determining trace rare earth ions is presented. In a medium of 0.02mol/L NH₄Cl,1. 0×10^?3mol/L Cu(II),1.0×10^?5 mol/L CPA-mCF₃, a very sensitive polarographic adsorptive wave is observed by using a single sweep oscillopolarograph at about –0.83V (vs. Ag/AgCl). The linear relationship between the peak current and the concentration of rare earth exists from 6. 0×10^?9 to 1. 0×10^?6 mol/L. The detection limit of rare earth is down to 2. 0×10^?9 mol/L for Tm³⁺. This method has been applied to determine trace RE in several samples of Chinese tea. The results are satisfactory. The composition of the complex is detected as RE (II): Cu (II): CPA-mCF₃ = 1: 1: 2.     

A Novel Screen-Printed and Carbon Paste Electrodes for Potentiometric Determination of Uranyl(II) Ion in Spiked Water Samples

Four new ion-selective electrodes (ISEs) based on poly-(1-4)-2-amino-2-deoxy-β-D-glucan (chitosan) ionophore were constructed for determination of uranyl ion (UO₂(II)) over wide concentration ranges. The linear concentration range for carbon paste electrodes (CPEs) was 1 × 10^–6–1 × 10^–2 mol/L with a detection limit of 1 × 10^–6 mol/L and that for the screen-printed electrode (SPEs) was 1 × 10^–5–1 × 10^–1 mol/L with a detection limit of 8 × 10^–6 mol/L. The slopes of the calibration graphs were 29.90 ± 0.40 and 29.10 ± 0.60 mV/decade for CPEs with dibutylphthalate (DBP) (electrode I) and o-nitrophenyloctylether (o-NPOE) (electrode II) as plasticizers, respectively. Also, the SPEs showed good potentiometric slopes of 29.70 ± 0.30 and 28.20 ± 1.20 mV/decade with DBP (electrode III) and o-NPOE (electrode IV), respectively. The electrodes showed stable and reproducible potential over a period of 54, 62, 101 and 115 days for electrodes I, II, III, and IV, respectively. The electrodes manifested advantages of low resistance, very fast response and, most importantly, good selectivities relative to a wide variety of other cations except Ce(III) ion which interfere seriously. The results obtained compared well with those obtained using atomic absorption spectrometry.