A chemiluminescence method for the detection of electrochemically generated H2O2 and ferryl porphyrin

Electrochemical formation of H2O2 and the subsequent ferryl porphyrin were examined by measuring luminol chemiluminescence and absorption spectrum using flow-injection method. Emission was observed under the cathodic potential (0.05 V at pH 2.0 and -0.3 V at pH 11.0) by the electrochemical reduction of buffer electrolytes solution but no emission was observed at anodic potentials. Fe(III)TMPyP solution was added at the down stream of the working electrode and was essential for the emission. Removal of dissolved O2 resulted in the decrease of emission intensity by more than 70%. In order to examine the lifetime of reduced active species, delay tubes were used in between working electrode and Fe(III)TMPyP inlet. Experimental results suggested the active species were stable for quite long. The emission was quenched considerably (>90%) when hydroperoxy catalase was added at the down stream of the working electrode whereas SOD had little effect. Significant inhibition of the emission by the addition of alkene at the down stream of the Fe(III)TMPyP inlet was considered as evidence of oxo-ferryl formation. The spectra at reduction potential under aerated condition were shifted to the longer wavelength (>430 nm) compared to the original spectrum of Fe(III)TMPyP (422 nm). All the spectra were perfectly reproduced by a combination of Fe(III)TMPyP and O=Fe(IV)TMPyP (438 nm) spectra. These observations lead to the conclusion that H2O2 was produced first by electrochemical reduction of O2, which then converted Fe(III)TMPyP into O=Fe(IV)TMPyP to activate luminol. The current efficiencies for the formation of H2O2 were estimated as about 30-65% in all over the pH.     

Tunable DNA photocleavage by an acridine-imidazole conjugate

We report the synthesis and characterization of photonucleases N,N'-bis[2-[bis(1H-imidazol-4-ylmethyl)amino]ethyl]-3,6-acridinediamine (7) and N-[2-[bis(1H-imidazol-4-ylmethyl)amino]ethyl]-3,6-acridinediamine (10), consisting of a central 3,6-acridinediamine chromophore attached to 4 and 2 metal-coordinating imidazole rings, respectively. In DNA reactions employing 16 metal salts, photocleavage of pUC19 plasmid is markedly enhanced when compound 7 is irradiated in the presence of either Hg(II), Fe(III), Cd(II), Zn(II), V(V), or Pb(II) (low-intensity visible light, pH 7.0, 22 degrees C, 8-50 microM 7). We also show that DNA photocleavage by 7 can be modulated by modifying buffer type and pH. Evidence of metal complex formation is provided by EDTA experiments and by NMR and electrospray ionization mass spectral data. Sodium azide, sodium benzoate, superoxide dismutase, and catalase indicate the involvement of type I and II photochemical processes in the metal-assisted DNA photocleavage reactions. Thermal melting studies show that compound 7 increases the Tm of calf thymus DNA by 10 +/- 1 degrees C at pH 7.0 and that the Tm is further increased upon the addition of either Hg(II), Cd(II), Zn(II), or Pb(II). In the case of Fe(III) and V(V), a colorimetric assay demonstrates that compound 7 sensitizes one electron photoreduction of these metals to Fe(II) and V(IV), likely accelerating the production of type I reactive oxygen species. Our data collectively indicate that buffer, pH, Hg(II), Fe(III), Cd(II), Zn(II), V(V), Pb(II), and light can be used to "tune" DNA cleavage by compound 7 under physiologically relevant conditions. The 3,6-acridinediamine acridine orange has demonstrated great promise for use as a photosensitizer in photodynamic therapy. In view of the distribution of iron in living cells, compound 7 and other metal-binding acridine-based photonucleases should be expected to demonstrate excellent photodynamic action in vivo.     

硫代草酸铁(Ⅲ)配合物的光化学

草酸铁(Ⅲ)钾是光敏感的,目前仍是一种常用的化学光量计。为了比较它与草酸根中的一个氧原子被硫取代生成的不对称配位体与铁(Ⅲ)形成的配合物对光的稳定性,我们研究了硫代草酸铁(Ⅲ)配合物的光化学。实验表明硫代草酸铁(Ⅲ)配合物也是光敏感的,但与草酸铁(Ⅲ)钾比较,在酸性溶液中会发生酸性水解。本文报导在恒离子强度0.1mol·1~(-1)(KCl),pH=4.05的Clark-Lubs缓冲溶液中的光化学。     

Precise method for the measurement of catalase activity in honey

An improved method is reported for the determination of catalase activity in honey. We tested different dialysis membranes, dialysis fluid compositions and amounts, dialysis temperatures, sample amounts, and dialysis times. The best results were obtained by dialysis of 7.50 g sample in a cellulose dialysis sack, using two 3 L portions of 0.015 M sodium phosphate buffer (pH 7.0) as the dialysis fluid at 4 degrees C for 22 h. As in previous methods, catalase activity was determined on the basis of the rate of disappearance of the substrate, H202, with the H202 determined spectrophotometrically at 400 nm in an assay system containing o-dianisidine and peroxidase. Trials indicated that the best solvent for the o-dianisidine was 0.2 M sodium phosphate buffer, pH 6.1; the best starting H202 concentration was 3 mM; the best HCl concentration for stopping the reaction was 6 N; and the best sample volume for catalase measurement was 7.0 mL. Precision values (relative standard deviations for analyses of 10 subsamples of each of 3 samples) were high, ranging from 0.48% for samples with high catalase activity to 1.98% for samples with low catalase activity.     

A ratiometric fluorescent chemosensor for iron: discrimination of Fe2+ and Fe3+ and living cell application

A newly designed probe, 6-thiophen-2-yl-5,6-dihydrobenzo[4,5]imidazo-[1,2-c] quinazoline (HL(1)) behaves as a highly selective ratiometric fluorescent sensor for Fe(2+) at pH 4.0-5.0 and Fe(3+) at pH 6.5-8.0 in acetonitrile-HEPES buffer (1/4) (v/v) medium. A decrease in fluorescence at 412 nm and increase in fluorescence at 472 nm with an isoemissive point at 436 nm with the addition of Fe(2+) salt solution is due to the formation of mononuclear Fe(2+) complex [Fe(II)(HL)(ClO(4))(2)(CH(3)CN)(2)] (1) in acetonitrile-HEPES buffer (100 mM, 1/4, v/v) at pH 4.5 and a decrease in fluorescence at 412 nm and increase in fluorescence at 482 nm with an isoemissive point at 445 nm during titration by Fe(3+) salt due to the formation of binary Fe(3+) complex, [Fe(III)(L)(2)(ClO(4))(H(2)O)] (2) with co-solvent at biological pH 7.4 have been established. Binding constants (K(a)) in the solution state were calculated to be 3.88 × 10(5) M(-1) for Fe(2+) and 0.21 × 10(3) M(-1/2) for Fe(3+) and ratiometric detection limits for Fe(2+) and Fe(3+) were found to be 2.0 μM and 3.5 μM, respectively. The probe is a "naked eye" chemosensor for two states of iron. Theoretical calculations were studied to establish the configurations of probe-iron complexes. The sensor is efficient for detecting Fe(3+)in vitro by developing a good image of the biological organelles.     

The interaction of cysteine with chromium(VI) ions under UV irradiation

In 0.1 M phosphate buffer (pH 7.2), the interaction of chromium(VI) with cysteine in the presence and absence of UV irradiation was studied by cyclic voltammetry and electronic spectroscopy techniques. The reduction of Cr(VI) by cysteine takes place through the formation of Cr(VI)-thioester intermediate. On the cyclic voltammograms of cysteine and Cr(VI) mixture, the peaks at -0.315 and -0.800 V were observed, and these peaks are corresponding to the reduction of Cr(VI)-thioester and thiyl radical, respectively. In the cysteine solution exposed to UV irradiation, the formation of free cystine was observed at -0.792 V. In the cysteine and Cr(VI) mixture exposed to UV irradiation, the peak current of thiyl radical increases while the peak current of Cr(VI)-thioester reaches a maximum at 15 min and then decreases by increasing UV irradiation time. The formation of the thioester in the reaction between Cr(VI) and cysteine in aqueous media has been studied by monitoring the decrease of Cr(VI) at 370 nm. It was observed that the reaction is catalyzed by the UV irradiation of the Cr(VI) and cysteine mixture.     

Study of the degradation of polyurethanes. III. Mechanism of the photodegradation of polyurethane

The effect of triplet sensitizers, benzophenone and anthraquinone and metal acetylacetonates [Co(II, III), Cu, Sn, and Ni] on the photodegradation of polyurethane was examined. Ultravioletvisible (UV-V) absorption spectra, gel formation, and luminescence emission of the polymer before and after irradiation were measured. Changes in UV-V absorption of the polymer and the formation of an insoluble fraction in the polymer were accelerated in the presence of the triplet sensitizers, and (Co(II, III)), Cu, and Sn acetylacetonates. Unirradiated polyurethane was excited by irradiation at 290 and 346 nm, and emitted light at 310 and 420 nm. After 1/2 hr irradiation emission of luminescence was observed at 430 nm, excitation at 290 and 346 nm; after 2hr irradiation at 530 nm, excitation at 420 nm was observed. The results suggest that photodegradation of the polyurethane proceeds via excited triplet states forming excimer between the polymers at the initial stage and exciplexes between the polymer and degradation products or intermediates after a certain irradiation.     

Spectrofluorimetric method for determination of aluminium with chromotropic acid and its application to water samples

A rapid and sensitive method for the trace level determination of aluminium based on the formation of a 1:1 complex with chromotropic acid (1,8-dihydroxynaphthlene-3,6-disulfonic acid) in an methanol medium is reported. The fluorescence intensity of the system was 50 times greater than that of the system without aluminium. This method is very sensitive and selective for the direct determination of aluminium ion. The fluorescence is excited at 346 nm and measured at 370 nm. The optimum conditions are a chromotropic acid concentration of 5.0 ml (1.0x10(-4) M) and pH 4.0+/-0.5 (acetic acid-sodium acetate buffer). The fluorescence intensity is a linear function of the concentration of Al(III) in the range 2-100 ng ml(-1) and the detection limit is 1.0 ng ml(-1). The method has been applied successfully to the determination of trace amount of Al(III) in tap, river and sea-water samples.     

OpticalIy Pumped Chemiluminescence of Indole-3-Acetic Acid

Optically pumped chemiluminescence of indole-3-acetic acid (IAA) was observed and studied. Rose Bengal (RB) was used as a photosensitizer. Long-lived chemiluminescence (CL) appeared after irradiation of the IAA/RB reaction mixture by monochromatic light at 550 nm (the maximum of RB absorption) or by visible light. The CL spectrum had a maximum at 480 nm. The kinetics of the CL decay were single exponential. Single-exponential kinetics were characterized by two experimentally measured values: initial CL intensity and exponential lifetime of the CL decay. We studied the influence of five parameters: (1) the rate of irradiation fluence, (2) the time of irradiation, (3) RIB concentration, (4) IAA concentration and (5) buffer pH on the initial CL intensity and the CL lifetime. Initial CL intensity was proportional to the rate of irradiation fluence and the concentration of RB. Saturation was observed in dependencies of initial CL intensity on the time of irradiation, the concentration of IAA and the buffer pH. The lifetime of the CL decay decreased with increasing pH and did not depend on the other four parameters. The mechanism explaining the experimental results was suggested and detailed kinetic analysis was performed to prove the proposed mechanism. Quantum yield of the CL and five rate constants that are involved in the mechanism were determined.     

Spectrophotometric determination of the stability constant of the Eu(III)-murexide complex

The values of the stability constants of the Ca(II) and lanthanide(III) complexes of murexide reported in the literature were determined without proper correction for binding of buffer ions to the metal ion. The constants are best determined without a buffer present. Accurate values of conditional stability constants for the Eu(III)—murexide complex (relative standard deviation better than 3%), of the differential molar absorptivity of the Eu(III)—murexide complex with respect to murexide at 480 nm (relative standard deviation better than 0.5%) and of the molar absorptivity of murexide at 520 and at 506 nm (precision better than 0.4%) at pH 5.0 and 6.5 at 15, 25 and 35° are reported. The accuracy and precision of the concentration of metal ion solution determined by using these conditional stability constants are discussed.     

A laser flash photolysis and pulse radiolysis study of primary photochemical processes of flumequine

The 355 nm laser flash photolysis of argon-saturated pH 8 phosphate buffer solutions of the fluoroquinolone antibiotic flumequine produces a transient triplet state with a maximum absorbance at 575 nm where the molar absorptivity is 14,000 M(-1) cm(-1). The quantum yield of triplet formation is 0.9. The transient triplet state is quenched by various Type-1 photodynamic substrates such as tryptophan (TrpH), tyrosine, N-acetylcysteine and 2-deoxyguanosine leading to the formation of the semireduced flumequine species. This semireduced form has been readily identified by pulse radiolysis of argon-saturated pH 8 buffered aqueous solutions by reaction of the hydrated electrons and the CO2*- radicals with flumequine. The absorption maximum of the transient semireduced species is found at 570 nm with a molar absorptivity of 2,500 M(-1) cm(-1). In argon-saturated buffered solutions, the semireduced flumequine species formed by the reaction of the flumequine triplet with TrpH stoichiometrically reduces ferricytochrome C (Cyt Fe3+) under steady state irradiation with ultraviolet-A light. In the presence of oxygen, O2*- is formed but the photoreduction of Cyt Fe3+ by O2*- competes with an oxidizing pathway which involves photo-oxidation products of TrpH.     

Fe(III) complexes of 1,4,8,11-tetraaza[14]annulenes as catalase mimics

The development of enzyme mimics of catalase which decompose hydrogen peroxide to water and molecular oxygen according to the 2:1 stoichiometry of native catalase and in aqueous solution at pH 7 and at micromolar concentrations of the enzyme model and hydrogen peroxide is reported. For this purpose, iron(III) complexes of 1,4,8,11-tetraaza[14]annulenes are prepared by various procedures. Efficacious preparations utilize reaction of the [N4] macrocyles with FeII salts in the presence of triphenylamine, followed by gentle oxidation of the FeII complexes by molecular oxygen or by tris(4-bromophenyl)aminium hexachloroantimonate. The complexes are characterized by SQUID magnetometry and by M?ssbauer, EPR, and UV/vis spectrometry. In the solid state, the iron(III) center of the catalytically active complexes exists in the intermediate (quartet, S = 3/2) spin state. Several of these complexes decompose hydrogen peroxide in aqueous buffer solution at pH 7.2 at room temperature with turnover numbers between 40 and 80. The apparent second-order rate constant for hydrogen peroxide decomposition is in the range of 1400-2400 M(-1) s(-1), about 3 orders of magnitude lower than the value for native catalase. Besides oxygen production, a non-oxygen releasing pathway of hydrogen peroxide decomposition is unveiled.     

Effect of Pyruvate on the Redox Behavior of the Iron (III)-(II) Couple

Abstract

Evidence for the formation of Fe(III) and Fe(II) complexes with pyruvate ion is presented. Complexes with a 1:2 ratio of Fe(II) to pyruvate and 1:1 ratio of Fe(III) to pyruvate were identified by spectrophotometry. The complexation results in partial kinetic control of the electrochemical oxidation of Fe(II) in citrate buffer. In addition, Fe(III) was found to be chemically reduced by pyruvate. The apparent first order rate constant at 25[ddot]C is 7.12 × 10^?2 s ^?1in pH 4.0 pyruvate buffer and 1.24 × 10^?1 s ^?1 in pH 3.2 pyruvate buffer. In pH 4.0 citrate buffer the reaction is not first order and is significantly slower.     

Asulam in Aqueous Solutions: Fate and Removal Under Solar Irradiation

The photodegradation of the pesticide asulam (methyl[(4-aminophenyl)sulfonyl]carbamate) in aqueous solutions (1.0 2 10 m 4 mol L m 1 = 23 mg L m 1 ) has been investigated with and without Fe(III). The asulam disappearance were measured by direct photolysis at 254 nm as a function of pH and oxygen concentration. Different photoproducts have been identified, among them a blue condensation product which was only observed upon selective direct excitation of asulam. In the presence of Fe(III) and by excitation at 365 nm, we obtained the complete mineralisation of asulam, while no complete transformation of organic carbons into CO 2 was observed by direct photolysis. The continuous formation of ” OH radicals generated from the excitation of Fe(III) species allowed the total mineralisation of asulam. Information is also given about the fate of asulam in aqueous solutions under solar irradiation.     

Direct and dye-sensitized aqueous photo-oxidation of 3-indoleacetic acid, methyl-3-indoleacetate and 1-methyl-3-indoleacetic acid 1-methyl-3-indoleacetic acid II: Quantum yields and mechamism

Mechanisms accounting for the types and yields of the products obtained in direct and dye-sensitized photo-oxidation of the compounds 3-indoleacetic acid (1a), methyl-3-indoleacetate (1b) and 1-methyl-3-indoleacetic acid (1c) in aqueous buffer (pH 5 or pH 8) containing 10% methanol are discussed. In the direct irradiation at pH 5 of acid 1a and its methyl ester 1b, the first detectable products are the corresponding 3-indolemethanols 6a and 6b, their methyl ethers 7a and 7b, and the dimeric compounds 14a and 14b, in aerobic and anaerobic conditions. The same primary products are detected in dye-sensitized photo-oxidation at pH 5. These results support the primary formation of radicals I and II, and of the peroxy forms III and IV, from which thermal reactions can explain all the products found. In both direct and dye-sensitized photo-oxidation at pH 8, only products from the oxidative cleavage of the indolic 2,3-double bond are observed. In dye-sensitized reactions, the products found are in accordance with the existence of competing type I (through radicals) and type II (through singlet oxygen) photosensitized oxygenation processes, their relative proportions depending on the pH of the medium. In direct irradiation, the same intermediates seem to be formed. Quantum yield values of 1a disappearance also depend on the experimental conditions, the highest value found being 28.5% for the direct irradiation at pH 5.     

Reaction of mercury(II) and xylenol orange-I Effect of the buffering media

The influence of the buffering medium on the reaction of Hg(II) with Xylenol Orange has been studied. Amine-type compounds are complexed by Hg(II)/Xylenol Orange with a sharp hyperchromic effect on the reagent itself, at 590 nm, but complex formation of Hg(II)/Xylenol Orange in non-amine-type buffer, such as citric acid-phosphate, gives a hypochromic effect on Xylenol Orange at 580 nm. Hg(II) is determined at pH 7.5 in two ranges of concentration, 2-9 ppm in citrate buffer, measured at 580 nm ( = 2.50 x 10(4)), and 6-11 ppm in hexamine buffer, at 590 nm ( = 4.18 x 10(4)).     

THE PHOTOCHEMISTRY OF p-AMINOBENZOIC ACID

We have studied the photoreactions occurring when p-aminobenzoic acid (PABA), a component of some sunscreens, is irradiated in aqueous solution. These studies were carried out in the presence and absence of oxygen, using light of lambda = 254 nm as well as light of wavelengths greater than 290 nm. In deoxygenated solution between pH 7.5 and 11.0, we found two photoproducts that were identified as 4-(4'-aminophenyl)aminobenzoic acid (I) and 4-(2'-amino-5'-carboxyphenyl)aminobenzoic acid (V); we used 1H and 13C NMR, electron impact mass spectrometry and synthesis by an independent route to identify each of these compounds. Rapid discoloration of the photolyzed sample was observed when PABA was irradiated in aerated solution. Although a number of products were detected under these conditions, the three most abundant stable compounds have been isolated and identified as 4-amino-3-hydroxybenzoic acid, 4-aminophenol and 4-(4'-hydroxyphenyl)aminobenzoic acid (IV). The latter compound was shown to result from rapid photo-induced oxidation of I in the presence of oxygen. Even in the presence of trace amounts of oxygen, the yield of I was significantly reduced in favor of IV. Studies of the thermal oxidation of I, coupled with evidence gathered from studies of the photochemistry of incompletely deoxygenated PABA solutions, indicate that 4-(2,5-cyclohexadien-4-one)iminobenzoic acid (III) is an intermediate on the pathway between I and IV. Qualitatively, we found that the photochemical reactions resulting from irradiation of PABA solutions with lambda = 254 nm light and light with lambda greater than 290 nm were the same. The quantum yields for formation of I and V are highly pH dependent, both being less than 10(-4) at pH 7 and rising steadily to values greater than 10(-3) at pH 11. The detailed pH dependence suggests that the deprotonated PABA radical cation may be an important intermediate entering into the reactions forming I and IV.     

Formation of compound I by photo-oxidation of compound II

[reaction: see text] Compound I is the heme-iron(IV)-oxo porphyrin radical cation formed in peroxidase and catalase enzymes by reaction with hydrogen peroxide. As an alternative to chemical oxidations of porphyrin-iron(III) species, various compound I species were produced by 355 nm laser flash photolysis photooxidation of the corresponding compound II species, porphyrin-iron(IV)-oxo derivatives. The method is demonstrated by production and kinetic studies of the compound I species from 5,10,15,20-tetrakis(pentafluorophenyl)porphyrin-iron, from horseradish peroxidase, and from wild-type horse skeletal myoglobin.     

Ring opening photoreactions of cytosine and uracil with ethylamine

The photochemical reactions of cytosine (Cyt) and uracil (Ura) with ethylamine, an analog of the side chain of the amino acid lysine, have been studied. After irradiation of Cyt in aqueous ethylamine at lambda = 254 nm, N-(N'-ethylcarbamoyl)-3-aminoacrylamidine (Ia) and N-(N'-ethylcarbamoyl)-3-ethylaminoacrylamidine (Ib) were isolated as products, while irradiation of Ura gave N-(N'-ethylcarbamoyl)-3-aminoacrylamide (IIa) and N-(N'-ethylcarbamoyl)-3-ethylaminoacrylamide (IIb) as products. Studies in which Ia and IIa were incubated with ethylamine at various pH values indicate that Ib and IIb are secondary products produced via thermal reactions of Ia and IIa with ethylamine. Heating of Ia and Ib leads to ring closure with the resultant formation of 1-ethylcytosine; small amounts of 1-ethyluracil are also produced. Heating of IIa and IIb produces 1-ethyluracil as the sole product. Spectroscopic properties were determined for each of these opened ring products, as well as for N-(N'-ethylcarbamoyl)-3-amino-2-methylacrylamidine (III) and N-(N'-ethylcarbamoyl)-3-amino-2-methylacrylamide (IV). Quantum yield measurements showed that Ia was formed with a phi of 1.6 x 10(-4) at pH 9.8, while phi for formation of IIa was 7.2 x 10(-4) at pH 11.5. A profile of the relative quantum yield for formation of Ia, determined as a function of pH, showed that the maximum quantum yield occurs at around pH 9.5; the analogous profile for IIa shows a maximum quantum yield at pH 11.3 and above. Acetone sensitization does not produce Ia in the Cyt-ethylamine system, which indicates that the known triplet state of Cyt is not involved in reactions leading to this opened ring product.     

Molecular mechanism of drug photosensitization. Part 3. Photohemolysis sensitized by diflunisal.

The lysis of red blood cells photosensitized by diflunisal (DFN) was investigated. Photohemolysis is inhibited by butylated hydroxyanisole and reduced glutathione, but is unaffected by mannitol and enhanced by sodium azide; the presence of oxygen markedly reduces the lysis which is accelerated in anaerobic conditions. These results contrast with those expected for a photodynamic mechanism. High lytic activity is observed for pre-irradiated solutions, mainly under anaerobic conditions. Direct irradiation of DFN in buffer solution at pH 7.4 leads to the formation, under anaerobic conditions, of compound 2'-(2',4'-difluoro-3'-carboxy-[1',1'-biphenyl]-4'-oxy)-4'- fluoro-4-hydroxy-[1,1'-biphenyl]-3-carboxylic acid (PhP), whereas under aerobic conditions formation of PhP is accompanied by unidentified photo-oxidation products; only compound PhP displays strong lytic activity. The overall results for DFN-photosensitized hemolysis suggest a mechanism involving a concerted action of free radicals, superoxide anion, singlet oxygen and sensitizer photoproducts.