纺锤形BiVO4微米管：低温离子熔盐合成及光催化性能

以Bi(NO₃)₃·5H₂O和NH₄VO₃为原料,以氯化胆碱和尿素组成的低温离子熔盐为反应介质,采用离子热合成法成功制备出了具有纺锤状外形的BiVO₄微米管。利用XRD,SEM,UV-Vis DRS,光催化测试等手段考察了BiVO₄颗粒的物相、形貌和光催化性能。结果表明,在离子熔盐环境下可以制备出结晶良好的BiVO₄纺锤形微米管,该BiVO₄微米管长10~15 μm,直径为1.5 μm左右,管壁厚约为200 nm。同时,研究了pH值对BiVO₄颗粒物相与形貌的影响,发现随着pH值的变化可分别合成出具有柱状、纺锤形微米管、柱状微米管和针柱状单斜相BiVO₄颗粒。光催化测试结果表明,这些单斜白钨矿BiVO₄颗粒在可见光范围都具有一定的光催化活性,其中纺锤状微米管对罗丹明B的降解效果最佳,可见光照射4.5 h后罗丹明B的降解率可达到93％。     

球形、花形和线状钒酸铋的可控合成及光催化性能

通过无模板、无助剂的可控水热法, 制备出球形、花形和线状钒酸铋(BiVO₄), 研究了其光学和可见光催化性能. 通过X射线衍射(XRD)和透射电镜(TEM)观测其结构和形貌特征. XRD谱线显示, 所制备的样品为单斜晶体结构. TEM结果表明, 通过控制水热过程的反应参数可以得到不同形貌的纳米粉体. 基于不同条件下制备的样品的微结构分析, 提出了这些不同形貌的形成机制. 紫外-可见漫反射光谱(UV-Vis DRS)表明BiVO₄样品的带隙能约为2.19-2.33 eV. 利用可见光(λ>420 nm)照射下的罗丹明B(RhB)降解实验评价了BiVO₄样品的光催化性能. 结果表明, BiVO₄的光催化活性比商用TiO₂催化剂P25 和掺氮TiO₂ (N-TiO₂)高得多. 所制备的球形BiVO₄光催化效率最高, 经可见光照射180 min, RhB溶液的降解率可达100%. 系统地研究了结构和形貌对不同pH值下制备的BiVO₄样品光催化活性的影响.     

硫掺杂橄榄状BiVO4上可见光降解亚甲基蓝和甲醛水溶液性能

在无和有S源(Na₂S或硫脲)存在的条件下,采用十二胺辅助的醇-水热法制备了多孔单斜晶相结构的BiVO_4-δ和不同含量S掺杂的BiVO_4-δ光催化剂.利用多种手段表征了催化材料的物化性质,评价了它们在可见光照射下催化降解亚甲基蓝或甲醛的反应活性.结果表明,所制光催化剂为单斜白钨矿晶相结构,具有多孔橄榄状形貌,比表面积为8.4-12.5m²/g,带隙能为2.40-2.48eV.在S掺杂BiVO_4-δ表面同时含有Bi⁵⁺,Bi⁴⁺,V⁵⁺和V⁴⁺物种.S掺杂对BiVO_4-δ光催化剂的活性影响很大.在可见光下照射下,BiVO_4-δS_0.08光催化剂对亚甲基蓝和甲醛降解反应显示出最高的光催化活性,这与其较高的表面氧物种浓度和较低的带隙能相关.     

纳米钒酸铋的微波快速合成及光催化性能研究

采用微波辅助加热法以NaVO₃溶液和Bi(NO₃)₃·5H₂O的硝酸溶液为反应物,在10～40 min内合成了纳米钒酸铋粉末。利用XRD、FTIR、TEM、UV-Vis等手段研究了反应时间对产物结构及形貌的影响。经测定反应10 min时,得到纯的四方相BiVO₄,随着反应时间的延长,逐渐出现单斜相的衍射峰,当反应40 min时,获得纯的单斜相BiVO₄。同时XRD和IR结果证明了相转变的过程。TEM分析表明不同的反应时间条件下样品呈现不同的形貌。不同反应时间下获得样品的光催化性能的结果表明,微波反应时间对BiVO₄结构的转变及光催化性能的改变起到了重要的作用。     

Zn2GeO4纳米棒的制备及发光性质

采用水热合成法制备了纯菱形相的Zn₂GeO₄纳米棒,研究了水热制备前驱体溶液的pH值对材料尺寸及形貌的影响以及Zn₂GeO₄纳米棒的光学性质。扫描电子显微镜（SEM）测试结果表明,随着前驱体溶液pH值的变化样品逐渐由微米级块状结构生长成为纳米颗粒,并且进一步形成纳米棒结构。纳米棒的尺寸由长200 nm变化到500 nm。室温光致发光（PL）光谱中观察到位于450和530 nm两个不同的发光峰,其分别源于Zn₂GeO₄的不同缺陷能级。     

室温固相法制备EuF3和SmF3纳米微粒

通过室温固相反应制备了不同形貌的EuF₃和SmF₃纳米微粒，并利用XRD，TEM，SEM，和XPS对产物进行了表征。研究表明氟源对所得的稀土氟化物的尺寸与形貌有着重要的影响。通过硝酸盐与NH₄F的反应得到了盘状的EuF₃和SmF₃微粒，而硝酸盐与HF·NH₄F的反应得到的是不规则的EuF₃和SmF₃微粒。EuF₃微粒的荧光光谱表明它们的发射峰的强度与尺寸与形貌有关。     

不同形貌纳米CoWO4的水热法制备及气敏性能

以Co（NO₃）₂·6H₂O、Na₂WO₄·2H₂O为主要原料,去离子水为溶剂,利用水热法在不同条件下制备了一系列的纳米CoWO₄,用XRD、TEM和比表面分析仪对产品的物相、形貌和比表面积进行了表征。较系统地探讨了水热条件（反应混合物pH值、反应时间、反应温度等）对产物物相和形貌的影响,并研究了不同形貌产品对甲醛、乙醇、氨气、苯和丙酮等的敏感性能。结果表明：水热条件对产品的物相和形貌有影响,在不同水热条件下,可成功制备CoWO₄纳米颗粒、纳米立方体及纳米棒;以纳米颗粒、纳米立方体及纳米棒样品制成的气敏元件对被试气体有不同程度的响应,其中以纳米颗粒为基的元件在210℃对1000μL·L^-1NH₃灵敏度为3.3。     

水热重结晶法制备羟基磷灰石纳米棒

本文以Ca(NO₃)₂和(NH₄)₂HPO₄为原料，采用重结晶法，在水热条件下制备了羟基磷灰石(HA)纳米棒；利用X-射线衍射(XRD)、透射电镜(TEM)、高分辨透射电镜(HRTEM)、红外光谱(FTIR)等分析测试手段，研究了pH值和晶化时间对HA组成和结构的影响。实验结果表明，室温混合pH值为7.5的沉淀物和pH值为10.5的清液，于180 ℃下水热处理10 h重结晶制得的HA纳米棒的平均长径比最长(约为28)；采用不同pH值的清液，体系的单体浓度(即化学势)改变时，得到的HA纳米棒的长径比不同；随着晶化时间延长，纳米棒的长径比先增大后减小。     

系列纳米结构锰氧化物的水热合成

以KMnO₄为锰源、抗坏血酸(AA)为还原剂,采用水热法制备系列纳米结构锰氧化物。通过调节反应物的物质的量的比、水溶液的pH值、反应温度和反应时间,制备出了不同纳米结构的锰氧化物,包括Mn₃O₄纳米粒子、MnOOH、α-MnO₂和β-MnO₂纳米棒。采用XRD和TEM测试技术对合成产物进行了表征,同时对其反应机理进行了探讨。     

Bi2MoO6/BiVO4异质结的水热合成和可见光催化活性

采用一步水热法制备Bi₂MoO₆/BiVO₄复合光催化剂. 利用X 射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、高分辨透射电子显微镜(HRTEM)等手段对其晶体结构和微观结构进行了表征. 结果表明, Bi₂MoO₆纳米粒子沉积在BiVO₄纳米片表面从而形成异质结结构. 紫外-可见漫反射光谱(UV-Vis DRS)表明所制备的Bi₂MoO₆/BiVO₄异质结较纯相Bi₂MoO₆和BiVO₄对可见光吸收更强. 由于形成异质结结构及其光吸收性能使Bi₂MoO₆/BiVO₄ 光催化活性有较大提高. 可见光下(λ>420 nm)光催化降解罗丹明B (RhB)实验结果表明,Bi₂MoO₆/BiVO₄光催化活性较纯相Bi₂MoO₆和BiVO₄高. Bi₂MoO₆/BiVO₄样品光催化性能提高的原因是Bi₂MoO₆和BiVO₄形成异质结, 从而有效抑制光生电子-空穴对的复合, 增大了可见光吸收范围及比表面积.     

Synthesis of large surface area nano-sized BiVO4 by an EDTA-modified hydrothermal process and its enhanced visible photocatalytic activity

In this work, monoclinic scheelite-type BiVO₄ nanoparticle with large surface area has been successfully synthesized, using Bi(NO₃)₃ and NH₄VO₃ as raw materials, through a hydrothermal process in the presence of ethylene diamine tetraacetic acid (EDTA). It is demonstrated that the nanoparticle size of as-prepared BiVO₄ becomes small by decreasing hydrothermal temperature, shortening hydrothermal reaction time and increasing EDTA amount used. The resulting BiVO₄ nanoparticle with large surface area exhibits a good photocatalytic performance for degrading phenol solution as a model organic pollutant under visible illumination. The key of this method is the chelating role of EDTA group in the synthetic process that it can greatly control the concentration of Bi³⁺, leading to the growth inhibition of BiVO₄ crystallite. The work provides a route for the synthesis of Bi-containing nano-sized composite oxides with large surface area.     

磁性BiVO4可见光催化材料的制备及光催化性能

采用水相沉淀法,以Fe3O4粒子为核心,令BiVO4沉淀附着于其上,制备了一种更易于从溶液中分离的磁性BiVO4可见光催化材料,以XRD、SEM、UV-Vis DRS、低温氮吸附-脱附等对其进行了表征。结果表明制备的磁性BiVO4为单斜白钨矿型,颗粒呈片状,粒径比普通BiVO4有所增大,在可见光区的吸收更强,吸收边红移程度随Fe3O4含量增加而增大,但比表面积并没有明显改变。并以可见光(λ≥400 nm)为光源,以亚甲基蓝溶液模拟染料废水,考察了其可见光催化活性,发现与纯BiVO4相比,磁性BiVO4具有更为良好的催化性能。通过考察各催化剂的DRS图谱以及暗反应后亚甲基蓝的浓度,发现这种降解效率上的提高是禁带宽度(Eg)降低、可见光吸收增加和对亚甲基蓝吸附量增大综合作用所导致的。这种吸附量的提升与比表面积无关,本工作以等电点的影响来解释此原因。     

草酸沉淀法合成自组装纳米Co_3O_4及性质

<正>一维纳米材料具有高比表面积,表现出很多奇特的物理和化学性能,因此一维纳米材料的合成和性质引起了人们的广泛关注。目前,合成一维纳米氧化物的方法很多,如模板法合成一维纳米铁氧体、水热法合成γ-MnOOH纳米棒、静电纺丝法合     

Synthesis and photocatalytic performances of BiVO4 by ammonia co-precipitation process

This paper reports the preparation and photocatalytic performance of Bismuth vanadate (BiVO₄) by a facile and inexpensive approach. An amorphous BiVO₄ was first prepared by a co-precipitation process from aqueous solutions of Bi(NO₃)₃ and NH₄VO₃ using ammonia. Followed by heating treatment at various temperatures, the amorphous phase converted to crystalline BiVO₄ with a structure between monoclinic and tetragonal scheelite. The crystallization of BiVO₄ occurred at about 523 K, while the nanocrystalline BiVO₄ were formed with a heat-treatment of lower than 673 K. However, when the heat-treatment was carried out at 773 K, the accumulation of nanocrystals to bulk particles was observed. The photocatalytic performances of the materials were investigated by O₂ evolution under visible-light, and MB decomposition under solar simulator. The results demonstrated that the crystalline structure is still the vital factor for the activities of both reactions. However, the crystallinity of BiVO₄ gives a major influence on the activity of O₂ evolution, whereas the surface area, plays an important role for photocatalytic MB decomposition.     

Facile solvothermal synthesis of highly active monoclinic scheelite BiVO4 for photocatalytic degradation of methylene blue under white LED light irradiation

In this study, BiVO₄ was successfully synthesized via the solvothermal process using a solvent mixture of ethylene glycol and water under different synthesis conditions of temperature and pH. Physicochemical properties such as crystal phase, morphology, and optical absorption of the as-synthesized BiVO₄ samples were characterized by X-ray diffraction (XRD), Raman spectra, field emission scanning electron microscopy (FE-SEM), and ultraviolet–visible diffraction reflection spectroscopy (UV–vis DRS). The XRD analysis showed that different synthesis conditions of temperature and pH significantly affected the growth of monoclinic BiVO₄ crystals oriented along (0 4 0) facets. Form SEM results, the synthesis conditions, including pH and temperature, have a great effect on the morphology of monoclinic structured BiVO₄. As the pH value increases in the range of 0–9 and temperature increases from 80 °C to 180 °C, the morphology of BiVO₄ changed from peanut-, rod-, and leaf-like shapes. The photocatalytic activities of as-synthesized BiVO₄ photocatalysts were evaluated by the photodegradation of methylene blue (MB) dye under irradiation of white LED light. We have found that by using appropriate synthesis conditions (the synthesis temperature of 140 °C and the synthesis pH of 7) the BiVO₄ exhibited high photocatalytic efficiency for MB degradation (about 82.30% after 180 min of irradiation). This result is due to the development of the BiVO₄ crystals oriented along (0 4 0) facets with an increase in the intensity ratio of I_(0 4 0)/I_(1 2 1). The growth of BiVO₄ crystals oriented along (0 4 0) facets may be beneficial to enhance the photocatalytic activity of monoclinic scheelite BiVO₄.     

一种新的低温固相法选择性制备单斜相钒酸铋

以Bi(NO₃)₃·5H₂O和NH₄VO₃为原料,采用一种新的低温固相法,通过控制研磨时间选择性制备高质量的单斜相BiVO₄。并采用X-射线粉末衍射(XRD),扫描电子显微镜(SEM),傅立叶红外光谱(FTIR)和紫外-可见漫反射吸收光谱(DRS)技术对产物进行分析表征。同时,实验结果表明研磨时间、干燥时间和水含量对单斜相BiVO₄的形成有很重要的作用。该方法具有合成温度较低,能耗较少,工艺简单,操作简便,环境友好等优点。最后,对低温固相法的机理进行了初步的探讨。     

Visible light photocatalytic activity of BiVO4 particles with different morphologies

Bismuth vanadate (BiVO₄) particles with different morphologies were synthesized by a one-step hydrothermal process and their optical and photocatalytic properties were investigated. Their crystal structure and microstructures were characterized using X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). XRD patterns demonstrate that the as-prepared samples are monoclinic cell. FESEM shows that BiVO₄ crystals can be fabricated in different morphologies by simply manipulating the reaction parameters of hydrothermal process. The UV–visible diffuse reflectance spectra (UV–vis DRS) reveal that the band gaps of BiVO₄ photocatalysts are about 2.07–2.21 eV. The as-prepared BiVO₄ photocatalysts exhibit higher photocatalytic activities in the degradation of rhodamine B (Rh B) under visible light irradiation (λ > 420 nm) compared with traditional N-doped TiO₂ (N-TiO₂). Furthermore, wheat like BiVO₄ sample reveals the highest photocatalytic activity. Up to 100% Rh B is decolorized after visible light irradiation for 180 min. The reason for the difference in the photocatalytic activities for BiVO₄ samples obtained at different conditions were systematically studied based on their shape, size and the variation of local structure.     

Concentration specific and tunable photoresponse of bismuth vanadate functionalized hexagonal ZnO nanocrystals based photoanodes for photoelectrochemical application

In the present work, dual layer BiVO₄/ZnO photoanode is instigated for photo-electrochemical (PEC) water splitting applications. Two different photocatalytic layers ZnO and BiVO₄, reduces charge carrier recombination and charge transfer resistance at photoanode/electrolyte junction. The concentration-specific, tunable and without ‘spike and overshoot’ features, photocurrent density response is originated by varying BiVO₄ concentration in the BiVO₄/ZnO photoanode. The crystal structure of ZnO (hexagonal wurtzite structure) and BiVO₄ (monoclinic scheelite structure) is confirmed by X-ray diffraction studies. The band gap of BiVO₄/ZnO was estimated to be ca. 2.42 eV through Kubler-Munk function F(R_∞) using diffuse reflectance spectroscopy. Electrochemical behavior of samples was analyzed with photocurrent measurements, electrochemical impedance, Mott-Schottky plots, bulk separation efficiency and surface transfer efficiency. The maximum photocurrent density of BiVO₄/ZnO photoanode was found to be 2.3 times higher than pristine ZnO sample.0.038 M BiVO₄/ZnO exhibited the highest separation efficiency of 72% and surface transfer efficiency of 64.7% at +1.23 V vs. RHE. Mott-Schottky study revealed the maximum charge carrier density in the same sample.     

Simulated Sunlight-Driven Degradation of Rhodamine B by Porous Peanut-Like TiO2/BiVO4 Composite

Porous peanut-like TiO₂/BiVO₄ composite nanostructures were synthesized via a template-free hydrothermal process with bismuth nitrate, ammonium metavanadate and anatase TiO₂ as raw materials. The crystal structures, morphologies, and optical properties of the as-prepared samples were characterized by X-ray powder diffraction, transmission electron microscope, scanning electron microscopy, X-ray photoelectron spectroscopy and UV–visible absorption spectra. Simulated sun-light induced photocatalytic degradation of Rhodamine B by porous peanut-like TiO₂/BiVO₄ nanostructures in the absence and presence of H₂O₂ has been investigated, and the results show these porous composite nanostructures with higher photocatalytic activity than pure BiVO₄ and anatase TiO₂. When TiO₂/BiVO₄ heterostructures were used as the photocatalysts under simulated sun-light irradiation, BiVO₄ could act as a sensitizer to absorb the visible light. Meanwhile, coupling different band-gap semiconductors of TiO₂ and BiVO₄, the compound facilitate separation of the photogenerated carriers under the internal field induced by the different electronic band structures of semiconductors.