Orientation ordering of N<Subscript>2</Subscript> molecules in vertically aligned CN<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> nanotubes

Arrays of vertically aligned nitrogen-doped carbon (CN _x ) nanotubes have been synthesized by decomposition of aerosol mixture of acetonitrile and ferrocene at 850°C. Nitrogen concentration in the outer shells of the CN _x nanotubes was found from X-ray photoelectron spectroscopy (XPS) data to reach ∼6%. The XPS N 1s spectra and N 1s near-edge X-ray absorption fine structure (NEXAFS) spectra identified three chemical forms of nitrogen in the CN _x nanotube arrays: pyridine-like, graphitic, and molecular nitrogen. The π ^* resonance of molecular nitrogen showed clear polarization dependence that indicates predominant orientation of N₂ molecules along the nanotubes axis. The estimated range of the polar angle distribution of the N₂ molecules orientation in the CN _x nanotube array amounts to 15°.     

Formation of Y-junction carbon nanotubes by catalytic CVD of methane

Y-junction carbon nanotubes were grown by catalytic CVD of methane at 700 ^°C on NiO-CuO-MoO(7:2:1) (w/w/w)/SiO₂ catalyst. For comparison, NiO-CuO(8:2) (w/w)/SiO₂ and NiO-MoO(8:2) (w/w)/SiO₂ catalysts were tested for carbon nanotube formation. TEM analysis indicates that no Y-junction structures were formed with the latter two catalysts. This finding elucidates why the addition of a small amount of MoO to NiO-CuO/SiO₂ catalyst is crucial for enhancing the formation of Y-junction carbon nanotubes.     

Synthesis, characterization and low field emission of CNx nanotubes

Aligned CN_x nanotubes were fabricated by pyrolyzing ethylenediamine on p-type Si(1 1 1) substrates using iron as the catalyst. Scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectrum (XPS) and Raman spectroscopy were used to characterize the CN_x nanotubes. The CN_x nanotubes with the average length of 20 μm and diameters in the range of 50–100 nm have the “bamboo-like” structure and worse crystalline order. The low-field emission measurements of the CN_x nanotubes indicated that 20 μA/cm² current densities were observed at an electric field of 1.4 V/μm and 1.280 mA/cm² were obtained at 2.54 V/μm. The CN_x nanotubes exhibit better field emission properties than the carbon nanotubes and the BCN nanotubes. The emission mechanism of CN_x nanotubes is also discussed.     

Nitrogen-doped carbon nanotubes with tunable structure and high yield produced by ultrasonic spray pyrolysis

Nitrogen-doped carbon nanotubes (CN_x) were prepared by ultrasonic spray pyrolysis from mixtures of imidazole and acetonitrile. Imidazole, as an additive, was used to control the structure and nitrogen doping in CN_x by adjusting its concentration in the mixtures. Scanning electron microscopy observation showed that the addition of imidazole increased the nanotube growth rate and yield, while decreased the nanotube diameter. Transmission electron microscopy study indicated that the addition of imidazole promoted the formation of a dense bamboo-like structure in CN_x. X-ray photoelectron spectroscopy analysis demonstrated that the nitrogen content varied from 3.2 to 5.2 at.% in CN_x obtained with different imidazole concentrations. Raman spectra study showed that the intensity ratio of D to G bands gradually increased, while that of 2D to G bands decreased, due to increasing imidazole concentration. The yield of CN_x made from mixtures of imidazole and acetonitrile can reach 192 mg in 24 min, which is 15 times that of CN_x prepared from only acetonitrile. The aligned CN_x, with controlled nitrogen doping, tunable structure and high yield, may find applications in developing non-noble catalysts and novel catalyst supports for fuel cells.     

Preparation and magnetic property of the composite of nitrogen-doped carbon nanotubes decorated with nickel nanoparticles

A magnetic composite of nitrogen-doped carbon nanotubes (CN_x) decorated with nickel nanoparticles was synthesized by a chemical precipitation and deoxidization method. The decorated CN_x were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The XRD pattern showed that CN_x, nickel nanoparticles and little nickel oxides coexisted in the composite, TEM observation indicated that nickel nanoparticles were highly dispersed on the outer walls of CN_x, Magnetic measurements by VSM demonstrated that the saturated magnetization and remanence of CN_x were improved, while the coercivity was lowered after decorating with nickel nanoparticles.     

Effect of nitrogen content on phase configuration, nanostructure and mechanical behaviors in magnetron sputtered SiCxNy thin films

SiC_xN_y thin films with different nitrogen contents were deposited by way of incorporation of different amounts of nitrogen into SiC_0.70 using unbalanced reactive dc magnetron sputtering method. Their phase configurations, nanostructures and mechanical behaviors were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, high-resolution transmission electron microscopy (HRTEM) and microindentation methods. The result indicated SiC_0.70 and all SiC_xN_y thin films exhibited amorphous irrespective of the nitrogen content. The phase configuration and mechanical behaviors of SiC_xN_y thin films strongly depended on nitrogen content. SiC_0.70 exhibited a mixture consisting of SiC, Si and a small amount of C. Incorporated nitrogen, on one hand linked to Si, forming SiN_x, on the other hand produced CN_x and C at the expense of SiC. As a result, an amorphous mixture consisting of SiC, SiN_x, C and CN_x were produced. Such effects were enhanced with increase of nitrogen content. A low hardness of about 16.5 GPa was obtained at nitrogen-free SiC_0.70. Incorporation of nitrogen or increase of nitrogen content increased the film hardness. A microhardness maximum of ∼29 GPa was obtained at a nitrogen content of 15.7 at.%. This value was decreased with further increase of N content, and finally a hardness value of ∼22 GPa was obtained at a N content of ∼25 at.%. The residual compressive stress was consistent with the hardness in the nitrogen content range of 8.6-25.3 at.%.     

2-Propanol photodegradation over nitrogen-doped NaNbO3 powders under visible-light irradiation

Nitrogen-doped perovskite-type materials, yellowish NaNbO_3−xN_x powders, had been developed as visible-light-sensitive photocatalysts for decomposition of gaseous 2-propanol. The NaNbO_3−xN_x samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), ultraviolet-visible (UV-vis) light diffuse reflectance spectroscopy, Brunauer-Emmett-Teller (BET) measurement, and scanning electron microscopy (SEM). The UV-vis spectra confirmed that the spectral response of the NaNbO₃ powders could be tuned to visible-light region by nitrogen doping technique. The photocatalytic activities of NaNbO_3−xN_x samples were evaluated by decomposing gaseous 2-propanol into acetone and CO₂ under visible-light irradiation (400 nm<λ<520 nm). The NaNbO_3−xN_x sample annealed at 833 K showed the highest visible-light photocatalytic activity among all the nitrogen-doped samples. The relationship between nitrogen doping amount and photocatalytic activity of NaNbO_3−xN_x samples was also investigated and discussed.     

Carbon nitride films by RF plasma assisted PLD: Spectroscopic and electronic analysis

Carbon nitride (CNx) thin films have been grown on Si 〈1 0 0〉 by 193 nm ArF ns pulsed laser ablation of a pure graphite target in a low pressure atmosphere of a RF generated N₂ plasma and compared with samples grown by PLD in pure nitrogen atmosphere. Composition, structure and bonding of the deposited materials have been evaluated by X-ray photoelectron spectroscopy (XPS), and Raman scattering. Significant chemical and micro-structural changes have been registered, associated to different nitrogen incorporation in the two types of films analyzed. The intensity of the reactive activated species is, indeed, increased by the presence of the bias confined RF plasma, as compared to the bare nitrogen atmosphere, thus resulting in a different nitrogen uptake in the growing films. The process has been also investigated by some preliminary optical emission studies of the carbon plume expanding in the nitrogen atmosphere. Optical emission spectroscopy reveals the presence of many excited species like C⁺ ions, C atoms, C₂, N₂; and CN radicals, and N₂⁺ molecular ions, whose relative intensity appears to be increased in the presence of the RF plasma. The films were also characterised for electrical properties by the “four-probe-test method” determining sheet resistivity and correlating surface conductivity with chemical composition.     

Preparation and magnetic property of the composite of nitrogen-doped carbon nanotubes decorated with nickel nanoparticles

A magnetic composite of nitrogen-doped carbon nanotubes (CN_x) decorated with nickel nanoparticles was synthesized by a chemical precipitation and deoxidization method. The decorated CN_x were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The XRD pattern showed that CN_x, nickel nanoparticles and little nickel oxides coexisted in the composite, TEM observation indicated that nickel nanoparticles were highly dispersed on the outer walls of CN_x, Magnetic measurements by VSM demonstrated that the saturated magnetization and remanence of CN_x were improved, while the coercivity was lowered after decorating with nickel nanoparticles.     

The preparation of nitrogen-doped TiO2−xNx photocatalyst coated on hollow glass microbeads

In this paper, the effective method for nitrogen-doped TiO_2−xN_x photocatalyst coated on hollow glass microbeads is described, which uses titanium tetraisopropoxide [Ti(iso-OC₃H₇)₄] as the raw materials and gaseous ammonia as a heat treatment atmosphere. The effects of heat treatment temperature and time on the photocatalytic activity of TiO_2−xN_x/beads are studied. The photocatalyst is characterized by the UV-vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), Brunauer-Emmett-Teller (BET) analysis and scanning electron microscopy (SEM). The results show that when the TiO_2−xN_x/beads is heated at 650 °C for 5 h, the photocatalytic activity of the TiO_2−xN_x/beads is the best. Compared with TiO₂, the photoabsorption wavelength range of nitrogen-doped TiO_2−xN_x red shifts of about 60 nm, and the photoabsorption intensity increases as well. The photocatalytic activity of the TiO_2−xN_x/beads is higher than that of the TiO₂/beads under visible light irradiation. The presence of nitrogen neither influences on the transformation of anatase to rutile, nor creates new crystal phases. When the TiO_2−xN_x/beads is heated at 650 °C for 5 h, the amount of nitrogen-doped is 0.53 wt.% in the TiO_2−xN_x. As the density of TiO_2−xN_x/beads prepared is lower than 1.0 g/cm³, it may float on water surface and use broader sunlight spectrum directly.     

Characterization of Pd-CeOx interaction on α-Al2O3 support

The Pd-Ce interaction was studied over CeO₂ (0.3-2.5 wt.%)-Pd (1 wt.%)/α-Al₂O₃ catalysts used in the reforming reaction of CH₄ with CO₂. The samples were characterized by using high resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS). The activity and selectivity behavior was in good agreement with that of other supported metal catalysts (Ni and Pd) modified with different promoters. The preliminary results of HRTEM would indicate that the CeO_x forms small crystallites around the Pd particle. The XPS analysis for the regions of Ce 3d and Pd 3d, gives an account of Ce being present mostly as Ce³⁺ and a high binding energy for Pd 3d_5/2 (335.3 eV), an evidence of Pd-Ce chemical interaction. The Pd/Al XPS intensity ratios vs. the Pd average particle size, determined by TEM, show an excellent correlation for fresh and used catalyst. These results indicate that the diminution of the Pd/Al ratios was due to Pd sintering. Consequently, the small amounts of CeO_x species do not cover the Pd particle, in agreement with the HRTEM results. The overall results stand for the promoter action mechanism of the CeO_x for the reforming reaction with CO₂.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.     

The interface reaction of high-k La2Hf2O7/Si thin film grown by pulsed laser deposition

The La₂Hf₂O₇ films have been deposited on Si (1 0 0) substrate by using pulsed laser deposition (PLD) method. X-ray diffraction (XRD) demonstrates that the as-grown film is amorphous and crystallizes after 1000 °C annealing. The interface structure is systematically studied by Synchrotron X-ray reflectivity (XRR), Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS). Silicide, silicate and SiO_x formations from interfacial reaction are observed on the surface of the Si substrate in the as-grown film. The impact of silicide formation on the electrical properties is revealed by capacitance-voltage (C-V) measurements. By post-deposition annealing (PDA), silicide can be effectively eliminated and C-V property is obviously improved.     

N-doped TiO2 photo-catalyst for the degradation of 1,2-dichloroethane under fluorescent light

The photo-catalytic degradation of 1,2-dichloroethane (1, 2-DCE) using nitrogen-doped TiO₂ photo-catalysts under fluorescent light irradiation was investigated. Highly pure TiO₂ and nitrogen-doped TiO₂ were prepared by a sol-gel method and characterized by thermo-gravimetric/differential-thermal analysis (TG/DTA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FTIR) spectroscopy. The results indicate that the photo-catalysts were mainly nano-size with an anatase-phase structure. The degradation reaction of 1,2-DCE was operated under visible-light irradiation, and the photo-catalytic oxidation was conducted in a batch photo-reactor with various nitrogen doping ratios (N/Ti = 0-25 mol%). The relative humidity (RH) was controlled at 0-20% and the oxygen concentration was controlled at 0-21%. The photo-degradation with nitrogen-doped TiO₂ showed superior photo-catalytic activity compared to that for pure TiO₂. TiO₂ doped with 15 mol% nitrogen exhibited the best photo-catalytic efficiency under the tested conditions. The products from the 1,2-DCE photo-catalytic oxidation were CO₂ and water; the by-products included dichloromethane, methyl chloride, ethyl chloride, carbon monoxide, and hydrogen chloride. The reaction pathway of 1,2-DCE indicates that oxygen molecules are the major factor that causes the degradation of 1,2-DCE in the gas phase.     

Poly(N-vinyl carbazole)-grafted multiwalled carbon nanotubes: Synthesis via direct free radical reaction and optical limiting properties

In this work, samples of poly(N-vinyl carbazole) (PVK)-grafted multiwalled carbon nanotubes (MWCNTs) were synthesized via free radical reaction. The ready-made PVK was allowed to react directly with MWCNTs at 70 °C in the presence of azo-bis-isobutyronitrile (AIBN). The purified deep grey products, which can dissolve in common organic solvents such as chloroform and 1,2-dichlorobenzene (DCB), were then characterized by FTIR spectra, TEM, TGA, elemental analysis, XPS, UV-vis spectra and Raman spectra. It was confirmed that PVK chains were grafted onto the surface of the carbon nanotubes (CNTs). The optical limiting properties of these PVK-grafted MWCNTs samples were investigated by open-aperture z-scan method. All of the samples of PVK-modified carbon nanotubes in chloroform showed optical limiting behavior better than that of C₆₀ in toluene.     

Structural and optical properties of ZnO nanorods grown on MgxZn1−xO buffer layers

ZnO nanorod arrays were synthesized by chemical-liquid deposition techniques on Mg_xZn_1−xO (x = 0, 0.07 and 0.15) buffer layers. It is found that varying the Mg concentration could control the diameter, vertical alignment, crystallization, and density of the ZnO nanorods. The X-ray diffraction (XRD), transmission electron microscopy (TEM), and selected area electron diffraction (SAED) data show the ZnO nanorods prefer to grow in the (0 0 2) c-axis direction better with a larger Mg concentration. The photoluminescence (PL) spectra of ZnO nanorods exhibit that the ultraviolet (UV) emission becomes stronger and the defect emission becomes weaker by increasing the Mg concentration in Mg_xZn_1−xO buffer layers.     

氮掺杂碳纳米管负载铂催化剂的简易制备及催化性能

以氮掺杂碳纳米管为载体,在温和条件下采用简单的浸渍法制备得到铂催化剂,铂的粒径分布在4～7 nm,且氮掺杂碳纳米管无需进行预处理. 采用X射线衍射仪、扫描电子显微镜、透射电镜和能量色散X射线仪等对Pt/CN_x催化剂进行了详细的表征. 结果表明,氮掺杂碳纳米管中高含量的氮原子能够有效俘获Pt(IV) 离子,且表面的含氮官能团及亲水性能的提高都有利于铂纳米粒子的分散. Pt/CN_x催化剂在烯丙醇加氢反应中表现出高的催化性能及循环使用性能,这是由于铂纳米粒子的高分散性及铂与载体间强的连接性阻止了Pt的流失及聚积,从而避免生成Pt黑导致失活等.     

Sputter deposition of high transparent TiO2−xNx/TiO2/ZnO layers on glass for development of photocatalytic self-cleaning application

In this study, TiO_2−xN_x/TiO₂ double layers thin film was deposited on ZnO (80 nm thickness)/soda-lime glass substrate by a dc reactive magnetron sputtering. The TiO₂ film was deposited under different total gas pressures of 1 Pa, 2 Pa, and 4 Pa with constant oxygen flow rate of 0.8 sccm. Then, the deposition was continued with various nitrogen flow rates of 0.4, 0.8, and 1.2 sccm in constant total gas pressure of 4 Pa. Post annealing was performed on as-deposited films at various annealing temperatures of 400, 500, and 600 °C in air atmosphere to achieve films crystallinity. The structure and morphology of deposited films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and atomic force microscopy (AFM). The chemical composition of top layer doped by nitrogen was evaluated by X-ray photoelectron spectroscopy (XPS). Photocatalytic activity of samples was measured by degradation of Methylene Blue (MB) dye. The optical transmittance of the multilayer film was also measured using ultraviolet-visible light (UV-vis) spectrophotometer. The results showed that by nitrogen doping of a fraction (∼1/5) of TiO₂ film thickness, the optical transmittance of TiO_2−xN_x/TiO₂ film was compared with TiO₂ thin film. Deposited films showed also good photocatalytic and hydrophilicity activity at visible light.     

Effects of UV photon irradiation on SiOx (0 < x < 2) structural properties

Thin films of a-SiO_x (0 < x < 2) were prepared by reactive r.f. magnetron sputtering from a polycrystalline-silicon target in an Ar/O₂ gas mixture. The oxygen partial pressure in the deposition chamber was varied so as to obtain films with different values of x. The plasma was monitored, during depositions, by optical emission spectroscopy (OES) system. Energy dispersive X-ray (EDX) measurements and infra-red (IR) spectroscopy were used to study the compositional and structural properties of the deposited layers.Structural modifications of SiO_x thin films have been induced by UV photons’ bombardment (wavelength of 248 nm) using a pulsed laser. IR spectroscopy and X-ray photoemission spectroscopy (XPS) were used to investigate the structural changes as a function of x value and incident energy. SiO_x phase separation by spinodal decomposition was revealed. The IR peak position shifted towards high wavenumber values when the laser energy is increased. Values corresponding to the SiO₂ material (only Si⁴⁺) have been found for laser irradiated samples, independently on the original x value. The phase separation process has a threshold energy that is in agreement with theoretical values calculated for the dissociation energy of the investigated material.For high values of the laser energy, crystalline silicon embedded in oxygen-rich silicon oxide was revealed by Raman spectroscopy.     

Vertically aligned carbon nanotubes from natural precursors by spray pyrolysis method and their field electron emission properties

Vertically aligned carbon nanotubes have been synthesized from botanical hydrocarbons: Turpentine oil and Eucalyptus oil on Si(100) substrate using Fe catalyst by simple spray pyrolysis method at 700°C and at atmospheric pressure. The as-grown carbon nanotubes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), thermogravimetric analysis (TGA), differential thermal analysis (DTA), and Raman spectroscopy. It was observed that nanotubes grown from turpentine oil have better degree of graphitization and field emission performance than eucalyptus oil grown carbon nanotubes. The turpentine oil and eucalyptus oil grown carbon nanotubes indicated that the turn-on field of about 1.7 and 1.93 V/μm, respectively, at 10 μA/cm². The threshold field was observed to be about 2.13 and 2.9 V/μm at 1 mA/cm² of nanotubes grown from turpentine oil and eucalyptus oil respectively. Moreover, turpentine oil grown carbon nanotubes show higher current density in relative to eucalyptus oil grown carbon nanotubes. The maximum current density of 15.3 mA/cm² was obtained for ∼3 V/μm corresponding to the nanotubes grown from turpentine oil. The improved field emission performance was attributed to the enhanced crystallinity, fewer defects, and greater length of turpentine oil grown carbon nanotubes.