Preparation and magnetic property of the composite of nitrogen-doped carbon nanotubes decorated with nickel nanoparticles

A magnetic composite of nitrogen-doped carbon nanotubes (CN_x) decorated with nickel nanoparticles was synthesized by a chemical precipitation and deoxidization method. The decorated CN_x were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The XRD pattern showed that CN_x, nickel nanoparticles and little nickel oxides coexisted in the composite, TEM observation indicated that nickel nanoparticles were highly dispersed on the outer walls of CN_x, Magnetic measurements by VSM demonstrated that the saturated magnetization and remanence of CN_x were improved, while the coercivity was lowered after decorating with nickel nanoparticles.     

Novel carbon nanotube iron oxide magnetic nanocomposites

A novel magnetic nanocomposite of γ-Fe₂O₃ nanoparticles decorated multiwalls carbon nanotubes (MWNTs) was synthesized for the first time by a simple chemistry precipitation method. The structure and morphology of the composite was characterized by X-ray powder diffractometer (XRD), TEM and EDS. The results of XRD and TEM show that γ-Fe₂O₃ nanoparticles is immobilized on the side wall of the MWNTs, the size of most of the particle is <5 nm.The EDS analysis shows that the atomic ratio of Fe to O is 2:3. The magnetization curves of the MWNTs and γ-Fe₂O₃ decorated MWNTs were measured by VSM at room temperature, which indicate that the saturated magnetization (Ms), remanence (Mr) and coercivity (Hc) of the decorated MWNTs are much larger than those of MWNTs, and the decorated MWNTs exhibit well magnetic properties.     

Magnetic properties of substituted strontium ferrite nanoparticles and thin films

SrFe_12−x(Zr_0.5Mg_0.5)_xO₁₉ nanoparticles and thin films with x=0-2.5 were synthesized by a sol-gel method on thermally oxidized silicon wafer (Si/SiO₂). Structural and magnetic characteristics of synthesized samples were studied employing x-rays diffraction (XRD), transmission electron microscopy (TEM), magnetic susceptometer, atomic force microscopy (AFM), field emission scanning electron microscopy (FE-SEM), and vibrating sample magnetometer (VSM). TEM micrographs display that the narrow size distribution of ferrite nanoparticles with average particle size of 50 nm were fabricated. Fitting obtained data of effective magnetic susceptibility by Vogel-Fulcher law confirms the existence of strong magnetic interaction among fine particles. XRD patterns and FE-SEM micrographs demonstrated that single phase c-axis hexagonal ferrite films with rather narrow grain size distribution were obtained. AFM micrographs exhibited that the surface roughness increases with an increase in Zr-Mg content. It was found from the VSM graphs that with an increase in substitution contents the coercivity decreases, while the saturation of magnetization increases. The Henkle plots confirms the existence of exchange coupling among nano-grain in ferrite thin films.     

Magnetic properties of La-substituted NiFe2O4 via egg-white precursor route

Nano-sized NiFe_2−xLa_xO₄ ferrites (x=0.00, 0.01, 0.02, 0.03, 0.04, 0.5, 0.07 and 0.09) were synthesized for the first time by using metal nitrate and egg-white extract in aqueous medium. The ferrites were characterized by DTA-TG, XRD, TEM, FT-IR and VSM techniques. The thermal decomposition behavior revealed that the precursors were completely decomposed at about 420 °C. TEM image shows agglomerated nanoparticles with crystallite sizes agrees well with that estimated by XRD measurement. XRD patterns show a secondary phase of LaFeO₃ besides the cubic structure of the La-substituted ferrites. The lattice parameters, X-ray density and crystallite size were found to increase with the increasing La content. The VSM measurement exhibited a ferromagnetic property for all the samples at room temperature. With increasing La, M_s was found to decrease while H_c increased. The decrease in the saturation magnetization is attributed to the paramagnetic properties of lanthanum, which prefer to substitute iron present in the octahedral sites. The increase in the coercivity is due to either the stronger magnetocrystalline anisotropy induced by La substitution or the change in the crystallite size.     

Magnetite-cobalt ferrite nanoparticles for kerosene-based magnetic fluids

Due to the magnetic anisotropy introduced by the Co²⁺ ion in octahedral sites of cubic spinel ferrites, it is possible to tailor the magnetic properties by changing the cobalt content. Magnetic fluids with magnetite-cobalt ferrite nanoparticles given by the formula Co_(x)Fe_(3−x)O₄ with x=0, 0.2 and 0.4 were prepared. Kerosene and oleic acid were used as liquid carrier and surfactant, respectively. Spherical magnetic nanoparticles were obtained by coprecipitation from metal salts and ammonium hydroxide; afterwards the magnetic fluids were obtained by a peptization process. Powder properties were characterized by X-ray diffraction (XRD), nitrogen adsorption–desorption isotherma (BET), vibrating sample magnetometry (VSM) and fluids by transmission electron microscopy (TEM), thermogravimetric analyzer (TGA), VSM and the short-circuited transmission line technique.     

Magnetic properties of Bi-doped Y3Fe5O12 nanoparticles

Bi³⁺ substituted garnet nanoparticles Y_3−xBi_xFe₅O₁₂ (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2 and 1.3) were fabricated by a sol–gel method and their crystalline structures and magnetic properties were investigated by using X-ray diffraction (XRD), IR spectroscopy, thermal gravity analysis–differential thermal analysis (TG-DTA), transmission electron microscope (TEM), Mössbauer spectroscopy and vibrating sample magnetometer (VSM). The XRD patterns of Y_3−xBi_xFe₅O₁₂ have only peaks of the garnet structure. From the results of VSM, it is shown that the saturation magnetization of sample is decreased with increasing the content of Bi ions. Meanwhile, it is observed that with the enhancement of the single magnetic domains surface spin effects, the saturation magnetization is raised as the particle size of samples is increased.     

Improving mechanical properties of a-CNx films by Ti-TiN/CNx gradient multilayer

Amorphous carbon nitride (a-CN_x) films with functional gradient Ti-TiN/CN_x underlayer were deposited by direct current magnetron sputtering. Microstructure and composition of the films were characterized by means of X-ray diffraction (XRD), Raman spectroscopy, atomic force microscope (AFM) and transmission electron microscopy (TEM). Mechanical and tribological properties were investigated by nanoindenter, scratch and ball-on-disk tribometer. The a-CN_x-based films suffer a graphitization process with the increasing deposition temperature, thus the hardness and elastic modulus decrease. With the design of the Ti-TiN/CN_x gradient underlayers, some important advantages of relatively thick CN_x films can be achieved, such as increased hardness, improved adhesion strength, and the wear resistance of the a-CN_x-based films can be also improved significantly.     

The role of copper ions on the structural and magnetic characteristics of MgZn ferrite nanoparticles and thin films

In this study Cu_xMg_0.5−xZn_0.5Fe₂O₄ (x=0-0.5) nanoparticles and thin films were prepared by sol-gel processing. The morphologies of nanoparticles were observed by transmission electron microscope (TEM). The Mössbauer spectroscopy (MS) was employed to determine the site preference of the constitutive elements. Magnetic dynamics of the nanoparticles was studied by the measurement of AC magnetic susceptibility versus temperature at different frequencies. The phenomenological Néel-Brown and Vogel-Fulcher models were employed to distinguish between interacting or non-interacting system. Results exhibited that there is strong interaction between fine particles. X-ray diffraction (XRD) patterns of the thin films indicate the formation of single-phase cubic spinel structure. Atomic force microscope (AFM) was employed to evaluate the surface morphologies of the prepared thin films. Vibrating sample magnetometer (VSM) was employed to probe magnetic properties of samples. It was found that with an increase in the amount of copper, the saturation of magnetization and initial permeability increase.     

Synthesis and magnetic characterization of Zn0.6Ni0.4Fe2O4 nanoparticles via a polyethylene glycol-assisted hydrothermal route

Zn-doped nickel ferrite nanoparticles (Zn_0.6Ni_0.4Fe₂O₄) have been prepared via a surfactant, polyethylene glycol assisted hydrothermal route. X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy, transmission electron microscopy (TEM), and vibrating scanning magnetometry (VSM) were used for the structural, morphological, and magnetic characterizations of the product, respectively. TEM analysis revealed that the nanoparticles have a narrow size distribution, with average particle size of 15±1 nm, which agrees well with the XRD based estimate of 14±2 nm. The absence of saturation and remanent magnetization, and coercivity in the high temperature region of the M-H curve and non-zero magnetic moments indicate superparamagnetism of the nanoparticles with a canted spin structure. The appearance of a peak on the temperature-dependent zero-field cooling magnetization curve at ∼190 K indicates the blocking temperature of the sample.     

Synthesis and characterization of CoxZn1−xFe2O4 magnetic nanoparticles via a PEG-assisted route

We present an investigation of properties of Co_xZn_1−xFe₂O₄ (x=0.0-1.0) nanoparticles synthesized by a polyethylene glycol (PEG)-assisted hydrothermal route. X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and vibrating scanning magnetometry (VSM) were used to characterize the structural, morphological and magnetic properties. The particle size obtained from TEM and XRD are consistent with each other. It was observed that the lattice constant for each composition decreases with increasing Co substitution and follows Vegard's law. Magnetization measurements show that while the materials with high Zn substitution are superparamagnetic at room temperature, they are ferromagnetic at temperatures lower than the blocking temperature. The materials with less Zn substitution are ferromagnetic below room temperature. Magnetizations and the coercivities of the samples decrease with the Zn substitution. The resultant overall magnetic behavior of the superparamagnetic samples are found to be considerably different than that of conventional superparamagnetic systems due to the antiferromagnetic interactions both in intra- and inter-cluster spins, and size (effective moment) distribution of the particles.     

Study of magnetic and structural properties of ferrofluids based on cobalt-zinc ferrite nanoparticles

Ferrofluids are colloidal systems composed of a single domain of magnetic nanoparticles with a mean diameter around 30 nm, dispersed in a liquid carrier. Magnetic Co_(1−x)Zn_xFe₂O₄ (x=0.25, 0.50, 0.75) ferrite nanoparticles were prepared via co-precipitation method from aqueous salt solutions in an alkaline medium. The composition and structure of the samples were characterized through Energy Dispersive X-ray Spectroscopy and X-ray diffraction, respectively. Transmission Electron Microscopy (TEM) studies permitted determining nanoparticle size; grain size of nanoparticle conglomerates was established via Atomic Force Microscopy. The magnetic behavior of ferrofluids was characterized by Vibrating Sample Magnetometer (VSM); and finally, a magnetic force microscope was used to visualize the magnetic domains of Co_(1−x)Zn_xFe₂O₄ nanoparticles. X-ray diffraction patterns of Co_(1−x)Zn_xFe₂O₄ show the presence of the most intense peak corresponding to the (311) crystallographic orientation of the spinel phase of CoFe₂O₄. Fourier Transform Infrared Spectroscopy confirmed the presence of the bonds associated to the spinel structures; particularly for ferrites. The mean size of the crystallite of nanoparticles determined from the full-width at half maximum of the strongest reflection of the (311) peak by using the Scherrer approximation diminished from (9.5±0.3) nm to (5.4±0.2) nm when the Zn concentration increases from 0.21 to 0.75. The size of the Co-Zn ferrite nanoparticles obtained by TEM is in good agreement with the crystallite size calculated from X-ray diffraction patterns, using Scherer's formula. The magnetic properties investigated with the aid of a VSM at room temperature presented super-paramagnetic behavior, determined by the shape of the hysteresis loop. In this study, we established that the coercive field of Co_(1−x)Zn_xFe₂O₄ magnetic nanoparticles, the crystal and nanoparticle sizes determined by X-ray Diffraction and TEM, respectively, decrease with the increase of the Zn at%. Finally, our magnetic nanoparticles are not very hard magnetic materials given that the hysteresis loop is small and for this reason Co_(1−x)Zn_xFe₂O₄ nanoparticles are considered as soft magnetic material.     

Growth of Y-junction bamboo-shaped CNx nanotubes on GaAs substrate using single feedstock

Nitrogen-doped Y-junction bamboo-shaped carbon nanotubes were synthesized by chemical vapor deposition of monoethanolamine/ferrocene mixture on GaAs substrate at 950 °C. The use of monoethanolamine as the C/N feedstock simplifies the experimental arrangement by producing ammonia during the growth process. The structure, morphology and graphitization of as-grown nitrogen-doped carbon nanotubes (CN_x) were examined by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy analysis. TEM analysis indicates that nanotubes have a bamboo-like structure. The nitrogen concentration on as-grown CN_x nanotube was found to be 7.8 at.% by X-ray photoelectron spectroscopy (XPS) analysis. XPS analysis also indicated that there are two different types of nitrogen atoms (pyridinic and graphitic) in these materials. The possible growth mechanism of formation of Y-junction CN_x nanotubes was briefly discussed. Field emission measurement suggested that as-grown CN_x nanotubes are excellent emitters with turn-on and threshold fields of 1.6 and 2.63 V/μm, respectively. The result indicated that monoethanolamine proves to be an advantageous precursor to synthesize Y-junction nitrogen-doped carbon nanotubes and such nanotubes might be an effective material to fabricate various field emission devices.     

Synthesis and magnetic properties of Mn–Zn ferrite nanoparticles

Mn–Zn ferrite nanoparticles (Mn_1−xZn_xFe₂O₄) are synthesized by a hydrothermal precipitation approach using metal sulfate solution and aqueous ammonia. The analysis methods of XRPD, TEM, TGA, and VSM are used to characterize the magnetic nanoparticles. Through the characterization of the precipitated nanoparticles, the effects of the reacting component proportions and preparation techniques on the Curie temperature, the magnetization, and the size distribution of Mn–Zn ferrite nanoparticles are discussed. Furthermore, the Mn–Zn ferrite nanoparticles are used to prepare ferrofluid. Variation of the magnetic properties of the ferrite nanoparticles with the composition content x of Zn and the magnetic moment of the nanoparticles are discussed.     

Preparation and photoluminescence characteristics of Tb-, Sm- and Dy-doped Y2O3 nanofibers by electrospinning

An electrospinning–calcination strategy was established to fabricate Y₂O₃ nanofibers doped with rare earth ions (Tb, Sm and Dy) using electrospun PVA/RE(NO₃)_x/Y(NO₃)₃ composite nanofibers as precursors (x=3.4). The prepared nanofibers were characterized by XRD, FESEM, EDS, (HR)TEM and PL analyses. Based on the experimental results, a solid–solid growth mechanism (SS) was proposed to describe the formation of inorganic crystalline fibers from organic/inorganic composite nanofibers by calcination. It was determined that carbonaceous nanoparticles that were formed in the process of pre-carbonization adsorbed Y₂O₃:RE nanoparticles to grow Y₂O₃:RE crystal, and the resultant nanofibers exhibited a typical crystalline domain with grain boundary. The obtained Y₂O₃:RE nanofibers possessed excellent luminescent characteristics and could be used as an appreciable luminescent material.     

Substitutional effect of Cr ions on the properties of Mg–Zn ferrite nanoparticles

The effect of Cr³⁺ substitution in Mg–Zn ferrite, with a chemical formula Mg_0.5Zn_0.5Cr_xFe_2−xO₄ (x=0.0–1.0), synthesized by a sol–gel auto-combustion reaction is presented in this paper. The resultant powders were investigated by various techniques, including X-ray diffractometry (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR), vibrating sample magnetometry (VSM), and DC resistivity. The XRD pattern revealed that the cubic spinel structure is maintained for the all the compositions. The particle sizes measured from XRD and TEM are in good agreement with each other. The cation distribution suggests that Mg²⁺, Cr³⁺ and Fe³⁺ have strong preference towards octahedral B-site. The theoretical lattice constant and experimental lattice constant match each other very well. The IR analysis supports the presently accepted cation distribution. The saturation magnetization decreases linearly with increasing Cr³⁺ content. Curie temperatures are obtained by the Laoria and AC susceptibility techniques. The dc resistivity has been investigated as a function of temperature and composition.     

Investigations on structural and optical properties of Zn1−xGdxS nanoparticles

Zn_1−xGd_xS (x = 0.00, 0.02 and 0.04) nanoparticles were synthesized by facile chemical co-precipitation method using PVP as a surfactant. ZnS nanoparticles could be doped with Gd ions during synthesis without altering the XRD patterns of ZnS. Also, the pattern of the powders showed cubic zincblende structure. The particle size obtained from the XRD studies lies in the range 3-5 nm, whereas from TEM analysis it is 4 nm for x = 0.02 sample. The UV-Vis absorption spectra revealed that Zn_1−xGd_xS nanoparticles exhibit strong confinement effect as the blue shift in the absorption spectra with that of the undoped ZnS. The photoluminescence spectra showed enhanced luminescence intensity and the entry of Gd into host lattice.     

Synthesis and optical properties of Cr doped ZnS nanoparticles capped by 2-mercaptoethanol

Nanoparticles of Zn_1−xCr_xS (x=0.00, 0.005, 0.01, 0.02 and 0.03) were prepared by a chemical co-precipitation reaction from homogenous solutions of zinc and chromium salts. These nanoparticles were sterically stabilized using 2-mercaptoethanol. Here a study of the effect of Cr doping on structural, morphological and optical properties of nanoparticles was undertaken. Elemental analysis, morphological, structural and optical properties have been investigated by energy dispersive analysis of X-rays (EDAX), scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM) and UV-visible spectroscopy .EDAX measurements confirmed the presence of Cr in the ZnS lattice. XRD showed that ZnS:Cr nanoparticles crystallized in zincblende structure with preferential orientation along (1 1 1) plane. The average sizes of the nanoparticles lay in the range of 3-6 nm and lattice parameters were in the range of 5.2-5.4 Å. Lattice contraction was observed with an increase of Cr concentration. The particle size and lattice parameters obtained from TEM and SAED images were in agreement with the XRD results. The absorption edge shifted to lower wavelengths with an increase in Cr concentration as per UV-Vis spectroscopy. The band gap energy values were in the range of 3.85-4.05 eV. This blueshift is attributed to the quantum confinement effect.     

Characterization of sol-gel-prepared nanoferrites

Spinel Co_1−xMn_xFe₂O₄ nanoparticles were prepared by the sol-gel combustion technique. X-ray diffraction (XRD), atomic force microscopy (AFM) and vibration sample magnetometer (VSM) studies have been carried out in order to understand the temperature dependence of their properties. It is observed that the high concentration of Mn²⁺ substituted into CoFe₂O₄ tends to reduce the particle size. Furthermore, the influence of Mn on the magnetic and thermal characteristics of Co_1−xMn_xFe₂O₄ nanoparticles has been investigated in detail.     

Band gap narrowing and fluorescence properties of nickel doped SnO2 nanoparticles

Nickel-doped tin oxide nanoparticles (sub-5 nm size) with intense fluorescence emission behavior have been synthesized by sol-gel route. The structural and compositional analysis has been carried out by using XRD, TEM, FESEM and EDAX. The optical absorbance spectra indicate a band gap narrowing effect and it was found to increase with the increase in nickel concentration. The band gap narrowing at low dopant concentration (<5%) can be assigned to SnO₂−SnO_2−x alloying effect and for higher doping it may be due to the formation of defect sub-bands below the conduction band.     

Transformation mechanism of n-butyl terminated Si nanoparticles embedded into Si1−xCx nanocomposites mixed with Si nanoparticles and C atoms

Bright-field transmission electron microscopy (TEM) images, high-resolution TEM (HRTEM) images, and fast-Fourier transformed electron-diffraction patterns showed that n-butyl terminated Si nanoparticles were aggregated. The formation of Si_1−xC_x nanocomposites was mixed with Si nanoparticles and C atoms embedded in a SiO₂ layer due to the diffusion of C atoms from n-butyl termination shells into aggregated Si nanoparticles. Atomic force microscopy (AFM) images showed that the Si_1−xC_x nanocomposites mixed with Si nanoparticles and C atoms existed in almost all regions of the SiO₂ layer. The formation mechanism of Si nanoparticles and the transformation mechanism of n-butyl terminated Si nanoparticles embedded into Si_1−xC_x nanocomposites mixed with Si nanoparticles and C atoms are described on the basis of the TEM, HRTEM, and AFM results. These results can help to improve the understanding of the formation mechanism of Si nanoparticles.