Enhanced Visible‐Light‐Induced Photoelectrocatalytic Degradation of Methyl Orange by CdS Sensitized TiO2 Nanotube Arrays Electrode

In this work, CdS sensitized TiO₂ nanotube arrays (CdS/TiO₂NTs) electrode was synthesized with the CdS deposition on the highly ordered titanium dioxide nanotube arrays (TiO₂NTs) by sequential chemical bath deposition method (S‐CBD). The as‐prepared CdS/TiO₂NTs was characterized by field‐emission scanning electron microscopy (FE‐SEM) and X‐ray diffraction (XRD). The results indicated that the CdS nanoparticles were effectively deposited on the surface of TiO₂NTs. The amperometric I‐t curve on the CdS/TiO₂NTs electrode was also presented. It was found that the photocurrent density was enhanced significantly from 0.5 to 1.85 mA/cm² upon illumination with applied potential of 0.5 V at the central wavelength of 253.7 nm. The photoelectrocatalytic (PEC) activity of the CdS/TiO₂NTs electrode was investigated by degradation of methyl orange (MO) in aqueous solution. Compared with TiO₂NTs electrode, the degradation efficiencies of CdS/TiO₂NTs electrode increased from 78% to 99.2% under UV light in 2 h, and from 14% to 99.2% under visible light in 3 h, which was caused by effective separation of the electrons and holes due to the effect of CdS, hence inhibiting the recombination of electron/hole pairs of TiO₂NTs.     

Mechanism of the formation of photosensitive nanostructured TiO<Subscript>2</Subscript> with low content of CdS nanoparticles

A method for synthesizing a CdS/TiO₂ composite material, active in the visible region, was described. The CdS/TiO₂ composite was obtained by the sol–gel synthesis of nanostructured TiO₂ in a medium of a stable colloidal solution of CdS nanoparticles. The TiO₂ matrix produced by the sol–gel process is amorphous and contains a nanocrystalline anatase phase, the content of which depends on the Ti(OBu)₄ hydrolysis rate. The content of CdS nanoparticles forming in the colloidal solution and participating in the TiO₂ matrix sensitization is determined by the initial CdS: Ti(OBu)₄ ratio. Although the content of CdS nanoparticles in the composite is low (no more than 3 wt %), the composite demonstrates catalytic activity in the visible region, thus proving the possibility of reducing the content of toxic CdS nanoparticles in the TiO₂ matrix without decreasing the photosensitivity of the CdS/TiO₂ composite.     

Effect of the method of production of TiO<Subscript>2</Subscript>/CdS nanohetero film structures on the effectiveness of photoinduced charge separation

The properties of TiO₂/CdS nanohetero structures produced by the chemical and photocatalytic deposition of CdS nanoparticles on the surface of nanocrystalline films of TiO₂ under the conditions of laser pulse photolysis were studied. It was shown that in the case of photocatalytically formed TiO₂/CdS nanocomposites the spatial separation of the photogenerated charges between the components of the hetero structure, leading to the formation of intermediates of the photochemical transformations (Ti^III centers in the TiO₂ nanoparticles and S^– radical-anions in the CdS nanoparticles), is an order of magnitude more effective.     

Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite

A C–N-doped TiO₂ nanotube (NT)/carbon nanorod composite is fabricated by chemical vapor deposition (CVD). Carbon nanorods are grown from the TiO₂ NTs, and partly graphitized, while TiO₂ is in the mixture of anatase and rutile. The C–N doping shifts the absorption edge of TiO₂ NTs to the visible light region; the formed carbon nanorods promote the charge carrier transfer from the TiO₂ surface to the electrolyte. Under the simulated solar light irradiation, the C–N-doped TiO₂ NTs show higher photocatalytic activity in the degradation of methyl orange (MO) than the undoped TiO₂ NTs.     

CdS‐Encapsulated TiO2 Nanotube Arrays Lidded with ZnO Nanorod Layers and Their Photoelectrocatalytic Applications

A novel TiO₂ nanotube array/CdS nanoparticle/ZnO nanorod (TiO₂ NT/CdS/ZnO NR) photocatalyst was constructed which exhibited a wide‐absorption (200–535 nm) response in the UV/Vis region and was applied for the photoelectrocatalytic (PEC) degradation of dye wastewater. This was achieved by chemically assembling CdS into the TiO₂ NTs and then constructing a ZnO NR layer on the TiO₂ NT/CdS surface. Scanning electron microscopy (SEM) results showed that a new structure had been obtained. The TiO₂ NTs looked like many “empty bottles” and the ZnO NR layer served as a big lid. Meanwhile the CdS NPs were encapsulated between them with good protection. After being sensitized by the CdS NPs, the absorption‐band edge of the obtained photocatalyst was obviously red‐shifted to the visible region, and the band gap was reduced from its original 3.20 eV to 2.32 eV. Photoelectric‐property tests indicated that the TiO₂ NT/CdS/ZnO NR material maintained a very high PEC activity in both the ultraviolet (UV) and the visible region. The maximum photoelectric conversion efficiencies of TiO₂ NT/CdS/ZnO NR were 31.8 and 5.98 % under UV light (365 nm) and visible light (420–800 nm), respectively. In the PEC oxidation, TiO₂ NT/CdS/ZnO NR exhibited a higher removal ability for methyl orange (MO) and a high stability. The kinetic constants were 1.77×10^?4 s^?1 under UV light, which was almost 5.9 and 2.6 times of those on pure TiO₂ NTs and TiO₂ NT/ZnO NR, and 2.5×10^?4 s^?1 under visible light, 2.4 times those on TiO₂ NT/CdS.     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基底表面制备一层TiO2纳米管阵列薄膜,然后通过水热反应在TiO2纳米管上负载CdS纳米粒子,形成CdS/TiO2纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO2纳米管的光电性能和光催化活性,结果表明,相比于TiO2纳米管,CdS/TiO2纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

Chemical synthesis of Ni/TiO<Subscript>2</Subscript> nanophotocatalyst for UV/visible light assisted degradation of organic dye in aqueous solution

The Ni/TiO₂ nanoparticles with different Ni dopant content were prepared by a modified sol–gel method. The structure and photoinduced charge properties of the as-prepared catalysts were determined using X-ray diffraction, transmission electron microscopy, UV–vis diffuse reflectance spectroscopy and surface photovoltage spectroscopy techniques, and the photocatalytic efficiency of these catalysts was tested using an organic dye. It was shown that Ni modification could greatly enhance the photocatalytic efficiency of these nanocomposite catalysts by taking the photodegradation of methyl orange as a model reaction. With appropriate ratio of Ni and TiO₂, Ni/TiO₂ nanocomposites showed the superior photocatalytic activity than the single TiO₂ nanoparticles. Surface photovoltage spectra demonstrated that Ni modification could effectively inhibit the recombination of the photoinduced electron and holes of TiO₂. This electron–hole pair separation conditions are responsible for the higher photocatalytic performance of Ni/TiO₂ nanocomposites in the visible region of electromagnetic spectrum.     

Sensitization of Mn with CdS nanoparticles via electrochemical deposition technique for photocurrent enhancement of nanomaterial’s-sensitized photoelectrochemical cells

A photoconversion efficiency of 2.12% was obtained under visible light illumination by nanostructure-sensitized photoelectrochemical cells using Mn/CdS as sensitizer loaded on TiO₂ nanotube arrays (NTAs) (Mn/CdS/TiO₂). Sensitization of Mn on CdS nanoparticles pre-loaded on TiO₂ NTAs was carried out by a two-step electrodeposition method. Compared with unsensitized TiO₂ NTAs, the photocurrent had increased from 0.03 to 4.12 for Mn/CdS/TiO₂ prepared at 1 min. The effects of deposited Mn on the physical, chemical, and photoelectrochemical properties of the CdS/TiO₂ NTAs nanostructure were investigated by using UV–visible diffuse reflectance spectroscopy, X-ray diffractometry, and field-emission scanning electron microscopy coupled with energy dispersive X-ray spectroscopy. The photoelectrochemical analysis was examined in a three-electrode system under a halogen illumination by using the prepared film as the photo-anode.     

Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Synthesis,characterization of B-doped TiO<Subscript>2</Subscript> nanotubes with high photocatalytic activity

B-doped TiO₂ nanotubes (B/TiO₂ NTs) were prepared by the combination of sol–gel process with hydrothermal treatment. The prepared catalysts were characterized by XRD, TEM and XPS. The photocatalytic activity of B/TiO₂ NTs was evaluated through the photodegradation of aqueous methyl orange. The results demonstrated that the 1.5% B/TiO₂ NTs calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with B significantly enhanced the photocatalytic efficiency.     

Room temperature synthesis of CdS nanoparticle-decorated TiO2 nanotube arrays by electrodeposition with improved visible-light photoelectrochemical properties

Controllable CdS nanoparticles (NPs) decorated on TiO₂ nanotube arrays (NTAs) were prepared via electrodeposition in DMSO solution at room temperature, aiming to improve the photoelectrochemical properties of TiO₂ NTA electrode in visible-light region. By tuning the concentrations of sulfur and Cd^2 + as well as the deposition time, CdS NPs with different sizes can be controllably synthesized at room temperature. Excellent photocurrent response and incident photo to current conversion efficiency were achieved with smaller CdS NPs with optimal reactant concentrations and deposition time, which can be attributed to highly efficient charge separation and high dispersion of CdS NPs on both inner and outer surfaces of TiO₂ nanotubes.     

Enhancement of visible-light photocatalytic activity of Cu-doped TiO<Subscript>2</Subscript> nanoparticles

Bare TiO₂ and Cu-doped TiO₂ nanoparticles with different nominal doping amounts of Cu ranging from of 0.5 to 5.0 mol% were synthesized using the modified sol–gel method. The samples were physically characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller-specific surface area, UV–Vis diffuse reflectance spectroscopy, zeta potential, X-ray photoelectron spectroscopy, inductively coupled plasma, and photoluminescence techniques. The Cu-doped TiO₂ exhibited good photocatalytic activity in mineralization of oxalic acid and formic acid under visible light irradiation. Photomineralization of oxalic and formic acids under visible light irradiation revealed greatly enhanced photoactivity exhibited by the 2.0 mol% Cu-doped TiO₂ photocatalyst compared to bare TiO₂ . The enhanced photocatalytic performance arises from copper ion doping in the TiO₂ structure, leading to an extended photoresponsive range, enhanced photogenerated charge separation, and transportation efficiency.     

Flower-like Au/Ag/TiO<Subscript>2</Subscript> nanocomposites with enhanced photocatalytic efficiency under visible light irradiation

Uniform flower-like TiO₂ coated Au nanostars and core-shell Au@Ag nanostars with different amounts of Ag coating were prepared through a facile method by hydrolysis of TiF₄ under an acidic environment. The photocatalytic capability of these flower-like nanocomposites under visible light irradiation was found to be enhanced by up to 4.7-fold compared to commercial P25 TiO₂ nanoparticles. The enhanced photocatalytic activity was ascribed to improved light absorption and hot electron injection from the photo-excited Au@Ag core to the TiO₂ shell.     

脉冲沉积制备Cu2O/TiO2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO₂纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu₂O纳米颗粒修饰改性TiO₂纳米管阵列,形成Cu₂O/TiO₂ 纳米管异质结复合材料. 利用场发射扫描电镜（FESEM）、场发射透射电镜（FETEM）、X射线衍射（XRD）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）对样品进行表征,重点研究了Cu₂O/TiO₂ 纳米管异质结的光电化学特性和对甲基橙（MO）的可见光催化降解性能. 结果表明,Cu₂O纳米颗粒均匀附着在TiO₂纳米管阵列的管口和中部位置,所制备的Cu₂O/TiO₂ 纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol·L^-1的CuSO₄溶液中制得的Cu₂O/TiO₂纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu₂O纳米颗粒影响光催化活性的机理进行了讨论.     

Visible‐Light Photoresponse of Gold Nanoparticles Supported on TiO2: A Combined Photocatalytic,Photoelectrochemical, and Transient Spectroscopy Study

In the context of gaining understanding on the origin of the visible‐light photoresponse of TiO₂ containing gold nanoparticles, the photocurrent spectra and photocatalytic H₂ evolution of titania (P25) and Au–P25 were compared. Whereas no photocurrent was detected upon visible‐light irradiation for either of the two photocatalysts, Au–P25 exhibited photocatalytic H₂ evolution for wavelengths between 400 and 575 nm. This contradictory behavior under visible‐light irradiation of Au–P25 was rationalized by transient absorption spectroscopy. It was suggested that photocatalytic H₂ generation results from methanol quenching of the charge‐separation state in each semiconductor nanoparticle, but the lack of photocurrent is due to the short lifetime of the charge separation, which makes interparticle charge migration for micrometric distances unlikely.     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基体表面制备一层TiO₂纳米管阵列薄膜, 然后通过水热反应在TiO₂纳米管上负载CdS纳米粒子, 形成CdS/TiO₂纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO₂纳米管的光电性能和光催化活性, 结果表明, 相比于TiO₂纳米管, CdS/TiO₂纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

Photocatalytic performance of TiO2 nanocrystals with/without oxygen defects

To investigate the role of oxygen defects on the photocatalytic activity of TiO₂, the TiO₂ nanocrystals with/without oxygen defects are successfully synthesized by the hydrothermal and sol-gel methods, respectively. The as-prepared TiO₂ nanocrystals with defects are light blue and the absorption edge of light is towards the visible light region (～420 nm). Raman and X-ray photoelectron spectroscopy (XPS) measurements all confirm that the concentration of oxygen vacancies in the TiO₂ synthesized by the sol-gel method is less than that synthesized through the hydrothermal route. The introduction of oxygen defects contributes to a new state in the band gap that narrows the band gap, which is the reason for the extension of light absorption into the visible light region. The photocurrent results confirm that this band-gap narrowing enhances the photocurrent response under simulated solar light irradiation. The TiO₂ with oxygen defects shows a higher photocatalytic activity for decomposition of a methylene blue solution compared with that of the perfect TiO₂ sample. The photocatalytic mechanism is discussed based on the density functional theory calculations and photoluminescence spectroscopy measurements.     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

CdS/TiO2 composite films for methylene blue photodecomposition under visible light irradiation and non-photocorrosion of cadmium sulfide

Cadmium sulfide/titanium dioxide (CdS/TiO₂) composite films were grown on glass by the chemical bath deposition (DBQ) and sol-gel/dip coating methods, respectively, in order to increase the photocatalytic activity of TiO₂ in photodegradation processes. The influence of the CdS deposition time on the morphology, optical absorption, and phononic modes of the composites were examined. Scanning electron microscopy (SEM) images showed clearly the CdS deposit on the TiO₂ surface. The absorbance spectra indicated that the absorption of composites depends on the CdS deposition time and the absorption edges are shifted to the visible range. Micro Raman spectra exhibited the phonons associated with the TiO₂ anatase and the longitudinal optic (LO) phonon of CdS whose intensity increases with the CdS deposition time. Photodegradation of methylene blue (MB) under visible light irradiation was observed in all films and the results were compared with those obtained with TiO₂ films. The decomposition is higher for the composite with the CdS deposition time of 15 min. This optimal deposition time allows maximal enhancement of the charge carriers transfer to TiO₂ involved in the photocatalysis. No signal associated with cadmium was detected by the atomic absorption spectroscopy (AAS), which means that the CdS photocorrosion does not occur since trap centers such as OH-Cd-S and Cl^?, which trap holes and inhibit the photocorrosion, are produced during the growth process.     

Photocatalytic Oxidation Based on Modified Titanium Dioxide with Reduced Graphene Oxide and CdSe/CdS as Nanohybrid Materials

Photocatalytic activity of TiO₂ nanoparticles in the visible light region was enhanced. TiO₂–CdSe and TiO₂–CdSe/CdS nanohybrids were supported on the reduced graphene oxide. These nanohybrid materials were applied as photocatalyst toward oxidation of aromatic alcohols under a mild condition and the molecular oxygen as oxidant. A plausible mechanism for the photocatalytic oxidation was also proposed. Desired nanohybrids were obtained via in situ fixation of CdSe/CdS on the surface of nanosheets of reduced graphene oxide (rGO). Finally, it was modified by TiO₂ sol nanoparticles through a hydrothermal method. The obtained nanomaterials, were characterized by SEM, TEM imaging, XRD, EDAX, DRS and XPS analyses. The size of nanohybrids materials were distributed mostly in a narrow range of 50–65 and 60–75 nm for TiO₂–rGO–CdSe and TiO₂–rGO–CdSe/CdS, respectively. These photocatalysts showed high catalytic activity under visible light irradiation in a short reaction time and even higher selectivity rather than UV irradiation. The yield of catalytic oxidation increased at least 25–30% for TiO₂–CdSe/CdS on rGO, which could be related to its higher light sensitivity and lower energy band gap. The photocatalysts were recycled and reused 8 times without significant loss of their activities due to their stability under visible light.