Thermoelastic instability of functionally graded materials with interaction of frictional heat and contact resistance

Both of the frictional heat and thermal contact resistance have a grave responsibility for the localized high temperature (hot spots) at the contact region, which is known as one of the most dangerous appearances in the brakes systems. In this paper, we study the thermoelastic instability (TEI) of a functionally graded material (FGM) half-plane sliding against a homogeneous half-plane at the in-plane direction. The interaction of the frictional heat and thermal contact resistance is taken into account in the TEI analysis. The material properties of the FGM half-plane are supposed to follow the exponential function along the thickness direction. The coupled TEI problem of FGMs is solved by using the perturbation method. The frictionally excited TEI of FGMs is also considered by neglecting the effect of the thermal contact resistance. The results show that the thermal contact resistance, sliding speed and gradient index have significant influence on the TEI. It is found that the variation of the gradient index of FGMs can increase the critical sliding speed and critical heat flux, and therefore improve the TEI of the sliding system.     

Two-dimensional thermoelastic contact problem of functionally graded materials involving frictional heating

The two-dimensional thermoelastic sliding frictional contact of functionally graded material (FGM) coated half-plane under the plane strain deformation is investigated in this paper. A rigid punch is sliding over the surface of the FGM coating with a constant velocity. Frictional heating, with its value proportional to contact pressure, friction coefficient and sliding velocity, is generated at the interface between the punch and the FGM coating. The material properties of the coating vary exponentially along the thickness direction. In order to solve the heat conduction equation analytically, the homogeneous multi-layered model is adopted for treating the graded thermal diffusivity coefficient with other thermomechanical properties being kept as the given exponential forms. The transfer matrix method and Fourier integral transform technique are employed to convert the problem into a Cauchy singular integral equation which is then solved numerically to obtain the unknown contact pressure and the in-plane component of the surface stresses. The effects of the gradient index, Peclet number and friction coefficient on the thermoelastic contact characteristics are discussed in detail. Numerical results show that the distribution of the contact stress can be altered and therefore the thermoelastic contact damage can be modified by adjusting the gradient index, Peclet number and friction coefficient.     

轴对称自由振动功能梯度材料微圆板中的热弹性阻尼

基于经典弹性薄板理论和单向耦合热传导理论,研究了材料性质沿厚度连续变化的功能梯度微圆板的热弹性阻尼特性．首先,考虑热力耦合效应,建立了功能梯度微圆板轴对称横向自由振动微分方程．然后,忽略温度梯度在面内的变化,建立了单向耦合变系数一维热传导方程．采用分层均匀化近似方法,将变系数热传导方程转化为一系列常系数的微分方程,利用上下表面的热边界条件和层间连续性条件获得了微圆板温度场解析解．将所得温度场代入微圆板的自由振动微分方程,得到了包含热弹性阻尼的复频率,从而获得了反映热弹性阻尼水平的逆品质因子．最后,针对材料性质沿板厚按幂函数变化的陶瓷-金属功能梯度微圆板,定量地分析材料梯度指数、几何尺寸、边界条件、温度环境等对微圆板热弹性阻尼的影响．     

The mixed mode crack problem in an FGM layer bonded to a homogeneous half-plane

In this paper, the plane elasticity problem of an arbitrarily oriented crack in a FGM layer bonded to a homogeneous half-plane is considered. The problem is modeled by assuming that the elastic properties of the FGM layer are exponential functions of the thickness coordinate and are continuous at the interface of the FGM layer and the half-plane.The Fourier transform technique is used to reduce the problem to the solution of a system of Cauchy-type singular integral equations, which are solved numerically. The stress intensity factors are computed for various crack orientations, crack locations and material parameters. The results show that crack length, crack orientation and the non-homogeneity parameter of the strip material have significant effect on the fracture of the FGM layer.     

功能梯度材料微梁的热弹性阻尼研究

基于Euler-Bernoulli梁理论和单向耦合的热传导理论,研究了功能梯度材料(functionally graded material,FGM)微梁的热弹性阻尼(thermoelastic damping,TED).假设矩形截面微梁的材料性质沿厚度方向按幂函数连续变化,忽略了温度梯度在轴向的变化,建立了单向耦合的变系数一维热传导方程.热力耦合的横向自由振动微分方程由经典梁理论获得.采用分层均匀化方法将变系数的热传导方程简化为一系列在各分层内定义的常系数微分方程,利用上下表面的绝热边界条件和界面处的连续性条件获得了微梁温度场的分层解析解.将温度场代入微梁的运动方程,获得了包含热弹性阻尼的复频率,进而求得了代表热弹性阻尼的逆品质因子.在给定金属-陶瓷功能梯度材料后,通过数值计算结果定量分析了材料梯度指数、频率阶数、几何尺寸以及边界条件对TED的影响.结果表明:(1)若梁长固定不变,梁厚度小于某个数值时,改变陶瓷材料体积分数可以使得TED取得最小值;(2)固有频率阶数对TED的最大值没有影响,但是频率阶数越高对应的临界厚度越小;(3)不同的边界条件对应的TED的最大值相同,但是随着支座约束刚度增大对应的临界厚度减小;(4)TED的最大值和对应的临界厚度随着金属组分的增大而增大.     

Frictionless contact of a functionally graded magneto-electro-elastic layered half-plane under a conducting punch

This paper investigates the two-dimensional frictionless contact problem of a functionally graded magneto-electro-elastic materials (FGMEEMs) layered half-plane under a rigid flat or a cylindrical punch. It is assumed that the punch is a perfect electro-magnetic conductor with a constant electric potential and a constant magnetic potential. The magneto-electro-elastic (MEE) properties of the FGMEEM layer vary exponentially along the thickness direction. Using the Fourier transform technique, the contact problem can be reduced to Cauchy singular integral equations, which are then solved numerically to determine the normal contact stress, electric displacement and magnetic induction on the contact surface. Numerical results show that the gradient index, punch geometry and magneto-electro-mechanical loads have a significant effect on the contact behavior of FGMEEMs.     

非保守力下温度场中FGM圆板的非线性力学行为

研究了温度场中非保守功能梯度材料(FGM)圆板的非线性力学行为。基于经典板理论,推导了受非保守力作用的FGM圆板在温度场中的控制微分方程。采用打靶法分析了由陶瓷二氧化锆和金属钛合金两相材料组成的非保守FGM圆板在均匀和非均匀升温场中的非线性力学行为。给出了不同均匀升温和非均匀升温场下,FGM圆板在非保守载荷作用下的平衡路径和平衡构形。分析并讨论了均匀和非均匀升温、材料梯度指数对非保守圆板过屈曲和弯曲行为的影响。结果表明:温度场中,非保守FGM圆板发生弯曲而纯陶瓷圆板会发生过屈曲行为;当梯度指数p=2,非保守载荷q=52时,均匀升温场中非保守圆板的变形大于非均匀升温场中非保守圆板的变形。     

Electro-mechanical frictionless contact behavior of a functionally graded piezoelectric layered half-plane under a rigid punch

The frictionless contact problem of a functionally graded piezoelectric layered half-plane in-plane strain state under the action of a rigid flat or cylindrical punch is investigated in this paper. It is assumed that the punch is a perfect electrical conductor with a constant potential. The electro-elastic properties of the functionally graded piezoelectric materials (FGPMs) vary exponentially along the thickness direction. The problem is reduced to a pair of coupled Cauchy singular integral equations by using the Fourier integral transform technique and then is numerically solved to determine the contact pressure, surface electric charge distribution, normal stress and electric displacement fields. For a flat punch, the normal stress intensity factor and electric displacement intensity factor are also given to quantitatively characterize the singularity behavior at the punch ends. Numerical results show that both material property gradient of the FGPM layer and punch geometry have a significant influence on the contact performance of the FGPM layered half-plane.     

Analysis for the thermoelastic bending of a functionally graded material cylindrical shell

An analytic study for thermoelastic bending of a functionally graded material (FGM) cylindrical shell subjected to a uniform transverse mechanical load and non-uniform thermal loads is presented. Based on the classical linear shell theory, the equations with the radial deflection and horizontal displacement are derived out. An arbitrary material property of the FGM cylindrical shell is assumed to vary through the thickness of the cylindrical shell, and exact solution of the problem is obtained by using an analytic method. For the FGM cylindrical shell with fixed and simply supported boundary conditions, the effects of mechanical load, thermal load and the power law exponent on the deformation of the FGM cylindrical shell are analyzed and discussed.     

考虑前屈曲耦合变形时功能梯度简支梁的稳定性分析

在某些边界条件下,功能梯度材料（FGM）梁会由于拉弯耦合产生前屈曲耦合变形,而该变形对FGM梁的稳定性有影响。本文假设FGM梁的材料性质只沿厚度方向进行变化,基于经典非线性梁理论和物理中面概念,推导出FGM梁的平衡方程以及包含前屈曲耦合变形影响的屈曲控制方程,并用打靶法进行数值求解。讨论了前屈曲耦合变形、梯度指数以及材料性质的温度依赖等因素对FGM梁非线性变形和稳定性的影响。     

功能梯度矩形厚板的三维热弹性分析

直接从三维热弹性力学基本方程出发，通过引入两个位移函数和两个应力函数，导出了一个二阶的齐次状态方程和一个四阶的非齐次状态方程。分析中采用了层合近似模型，即将板划分成厚度足够小的若干薄层，从面可将每一层内的材料常数近似为常数。给出了任意厚度的四边简支横观各向同性功能梯度矩形板的热弹性分析，特别当板较薄时，与薄板理论进行了数值对比，发现两者结果吻合很好。最后研究了材料梯度指标对热弹性场的影响，结果显示梯度指标对热应力和位移都有着显著的作用：在不同的区间，梯度指标对它们有不同的影响；并且在同一区间，梯度指标对两者的影响程度也有所不同。     

Elasticity solution for an FGM cylindrical panel integrated with piezoelectric layers

The three-dimensional elasticity solution for static analysis of a functionally graded material (FGM) cylindrical panel with simply supported edges is developed. The modulus of elasticity varies continuously throughout the thickness direction in the form of an exponential function. The panel is bonded with piezoelectric layers. Using Fourier series expansions in the axial and circumferential directions, the state equations are derived. The stress, displacement and electric potential distributions are obtained by solving these state equations. The influences of the material gradient index, applied voltage, and radius to thickness ratio on the static behavior of FGM shell are also studied.     

功能梯度材料明德林矩形微板的热弹性阻尼

功能梯度材料微板谐振器热弹性阻尼的建模和预测是此类新型谐振器热?弹耦合振动响应的新课题. 本文采用数学分析方法研究了四边简支功能梯度材料中厚度矩形微板的热弹性阻尼. 基于明德林中厚板理论和单向耦合热传导理论建立了材料性质沿着厚度连续变化的功能梯度微板热弹性自由振动控制微分方程. 在上下表面绝热边界条件下采用分层均匀化方法求解变系数热传导方程, 获得了用变形几何量表示的变温场的解析解. 从而将包含热弯曲内力的结构振动方程转化为只包含挠度振幅的偏微分方程. 然后,利用特征值问题在数学上的相似性,求得了四边简支条件下功能梯度材料明德林矩形微板的复频率解析解, 进而利用复频率法获得了反映谐振器热弹性阻尼水平的逆品质因子. 最后, 给出了材料性质沿板厚按幂函数变化的陶瓷?金属组分功能梯度矩形微板的热弹性阻尼数值结果. 定量地分析了横向剪切变形、材料梯度变化以及几何参数对热弹性阻尼的影响规律. 结果表明, 采用明德林板理论预测的热弹性阻尼值小于基尔霍夫板理论的预测结果, 而且两者的差别随着相对厚度的增大而变得显著.      

Effect of a thin coating on the pressure distribution in contact problems involving frictional heat generation

A thermoelastic problem for a layer of finite thickness one of whose surfaces is subjected to the action of normal pressure and heat flux is studied. A relationship among vertical displacements of the surface of the layer, the surface temperature, and the disturbing factors is obtained. Corresponding relations are obtained for a layer of small thickness. An axisymmetric contact problem for a rigid heat-conducting base whose surface is coated with a thin elastic layer is studied as an example. Franko L'vov State University, L'vov 290602. Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 39, No. 1, pp. 110–118, January–February, 1998.     

Stochastic thermoelastic problem of a functionally graded plate under random temperature load

This study attempts to derive the statistics of temperature and thermal stress in functionally graded material (FGM) plates exposed to random external temperatures. The thermomechanical properties of the FGM plates are assumed to vary arbitrarily only in the plate thickness direction. The external temperatures are expressed as random functions with respect to time. The transient temperature field in the FGM plate is determined by solving a nonhomogeneous heat conduction problem for a multilayered plate with linear nonhomogeneous thermal conductivity and different homogeneous heat capacity in each layer. The autocorrelations and power spectrum densities (PSDs) of temperature and thermal stress are derived analytically. These statistics for FGM plates composed of partially stabilised zirconia (PSZ) and austenitic stainless steel (SUS304) are computed under the condition that the fluctuation in the external temperature can be considered as white noise or a stationary Markov process.     

功能梯度压杆后屈曲形态的数值计算

基于轴线可伸长杆的过屈曲精确数学模型,采用打靶法对两端简支功能梯度压杆后屈曲行为进行了数值分析.其中假设功能梯度梁的材料性质沿厚度方向按照幂函数连续变化.给出了不同梯度指标下FGM杆的后屈曲特征曲线,并与金属和陶瓷两种单相材料杆的相应特性进行了比较,分析和讨论了载荷、材料的梯度指数、长细比对杆后屈曲平衡路径的影响.     

Properties degradation induced by transverse cracks in general symmetric laminates

This paper presents the details of a methodology for predicting the thermoelastic properties degradation in general symmetric laminates with uniform ply cracks in some or all of the 90° layers. First, a stress transfer method is derived by using the concept of state space equation. The laminate can be subjected to any combination of in-plane biaxial and shear loading, and the uniform thermal loading is also taken into account. The method takes into account all independent material constants and guarantees continuous fields of all interlaminar stresses across interfaces between material layers. By this method, a laminate may be composed of an arbitrary number of monoclinic layers and each layer may have different material property and thickness. Second, the concept of the effective thermoelastic properties of a cracked laminate is introduced. Based on the numerical solutions of specially designed loading cases, the effective thermoelastic constants of a cracked laminate can be obtained. Finally, the applications of the methodology are shown by numerical examples and compared with numerical results from other models and experiment data in the literature. It is found that the theory provides good predictions of the thermoelastic properties degradation in general symmetric laminates.     

Transient hyperbolic heat conduction in thick-walled FGM cylinders and spheres with exponentially-varying properties

This paper focuses on non-Fourier hyperbolic heat conduction analysis for heterogeneous hollow cylinders and spheres made of functionally graded material (FGM). All the material properties vary exponentially across the thickness, except for the thermal relaxation parameter which is taken to be constant. The cylinder and sphere are considered to be cylindrically and spherically symmetric, respectively, leading to one-dimensional heat conduction problems. The problems are solved analytically in the Laplace domain, and the results obtained are transformed to the real-time space using the modified Durbin’s numerical inversion method. The transient responses of temperature and heat flux are investigated for different inhomogeneity parameters and relative temperature change values. The comparisons of temperature distribution and heat flux between various time and material properties are presented in the form of graphs.     

Thermo-mechanical contact behavior of a finite graded layer under a sliding punch with heat generation

The problem of a rigid punch contacting with a finite graded layer on a rigid substrate is investigated within the framework of steady-state plane strain thermoelasticity, in which heat generated by contact friction is considered with a constant friction coefficient and inertia effects are neglected. The material properties of the graded layer vary according to an exponential function in the thickness direction. Fourier integral transform method and transform matrix approach are employed to reduce the current thermocontact problem to the second kind of Cauchy-type singular integral equation. Distributions of the contact pressure and the in-plane stress under the prescribed thermoelastic environment with different parameter combinations, including ratio of shear moduli, relative sliding speed, friction coefficient and thermal parameters are obtained and analyzed, as well as the stress singularity and the stress intensity factors near the contact edges. The results should be helpful for the design of surfaces with strong wear resistance and novel graded materials for real applications.     

Thermal stresses around a crack in the nonhomogeneous interfacial layer between two dissimilar elastic half-planes

Thermal stresses around a crack in the interfacial layer between two dissimilar elastic half-planes are solved. The surfaces of the crack are assumed to be insulated. The material constants of the interfacial layer are assumed to vary continuously from those of the upper half-plane to those of the lower half-plane. Uniform heat flows perpendicular the crack. Stress intensity factors are calculated numerically for several thicknesses of the interfacial layer.