Nanostructured Pt/GC model electrodes prepared by the deposition of metal-salt-loaded micelles

Novel, nanostructured, carbon-supported Pt model electrodes with homogeneously distributed Pt nanoparticles of uniform size were fabricated and analyzed with respect to their electrochemical properties. For this purpose, Pt-salt-loaded micelles were deposited on a glassy carbon substrate and subsequently exposed to an oxygen plasma and a H2 atmosphere for removal of the polymer carriers and reduction of the Pt salt. The morphology of the resulting nanoparticles and their electrochemical/electrocatalytic properties were characterized by high-resolution scanning electron microscopy, X-ray photoelectron spectroscopy, cyclic voltammetry, and differential electrochemical mass spectrometry for CO electrooxidation. The data demonstrate that this method is generally suited to the production of nanostructured model electrodes with well-defined and independently adjustable particle size and interparticle distance distributions, which are specifically suited for quantitative studies of transport processes in electrocatalytic reactions.     

Characterization of Pt nanoparticles deposited onto carbon nanotubes grown on carbon paper and evaluation of this electrode for the reduction of oxygen

Multiwalled carbon nanotubes (MWCNTs) were grown on the fibers of a commercial porous carbon paper used as carbon-collecting electrodes in fuel cells. The tubes were then covered with Pt nanoparticles in order to test these gas diffusion electrodes (GDEs) for oxygen reduction in H2SO4 solution and in H2/O2 fuel cells. The Pt nanoparticles were characterized by cyclic voltammetry, transmission electron microscopy, and X-ray photoelectron spectroscopy. The majority of the Pt particles are 3 nm in size with a mean size of 4.1 nm. They have an electrochemically active surface area of 60 m2/g Pt for Pt loadings of 0.1-0.45 mg Pt/cm2. Although the electroactive Pt surface area is larger for commercial electrodes of similar loadings, Pt/MWCNT electrodes largely outperform the commercial electrode for the oxygen reduction reaction in GDE experiments using H2SO4 at pH 1. On the other hand, when the same electrodes are used as the cathode in a H2/O2 fuel cell, they perform only slightly better than the commercial electrodes in the potential range going from approximately 0.9 to approximately 0.7 V and have a lower performance at lower voltages.     

A general method for the rapid synthesis of hollow metallic or bimetallic nanoelectrocatalysts with urchinlike morphology

We have reported a facile and general method for the rapid synthesis of hollow nanostructures with urchinlike morphology. In-situ produced Ag nanoparticles can be used as sacrificial templates to rapidly synthesize diverse hollow urchinlike metallic or bimetallic (such as Au/Pt) nanostructures. It has been found that heating the solution at 100 degrees C during the galvanic replacement is very necessary for obtaining urchinlike nanostructures. Through changing the molar ratios of Ag to Pt, the wall thickness of hollow nanospheres can be easily controlled; through changing the diameter of Ag nanoparticles, the size of cavity of hollow nanospheres can be facilely controlled; through changing the morphologies of Ag nanostructures from nanoparticle to nanowire, hollow Pt nanotubes can be easily designed. This one-pot approach can be extended to synthesize other hollow nanospheres such as Pd, Pd/Pt, Au/Pd, and Au/Pt. The features of this technique are that it is facile, quick, economical, and versatile. Most importantly, the hollow bimetallic nanospheres (Au/Pt and Pd/Pt) obtained here exhibit an area of greater electrochemical activity than other Pt hollow or solid nanospheres. In addition, the approximately 6 nm hollow urchinlike Pt nanospheres can achieve a potential of up to 0.57 V for oxygen reduction, which is about 200 mV more positive than that obtained by using a approximately 6 nm Pt nanoparticle modified glassy carbon (GC) electrode. Rotating ring-disk electrode (RRDE) voltammetry demonstrates that approximately 6 nm hollow Pt nanospheres can catalyze an almost four-electron reduction of O(2) to H(2)O in air-saturated H(2)SO(4) (0.5 M). Finally, compared to the approximately 6 nm Pt nanoparticle catalyst, the approximately 6 nm hollow urchinlike Pt nanosphere catalyst exhibits a superior electrocatalytic activity toward the methanol oxidation reaction at the same Pt loadings.     

Particle-size effect of nanoscale platinum catalysts in oxygen reduction reaction: an electrochemical and 195Pt EC-NMR study

Oxygen reduction reaction (ORR) measurements and (195)Pt electrochemical nuclear magnetic resonance (EC-NMR) spectroscopy were combined to study a series of carbon-supported platinum nanoparticle electrocatalysts (Pt/CB) with average diameters in the range of roughly 1-5 nm. ORR rate constants and H(2)O(2) yields evaluated from hydrodynamic voltammograms did not show any particle size dependency. The apparent activation energy of 37 kJ mol(-1), obtained for the ORR rate constant, was identical to that obtained for bulk platinum electrodes. Pt/CB catalysts on Nafion produced only 0.7-1% of H(2)O(2), confirming that the direct four-electron reduction of O(2) to H(2)O is the predominant reaction. NMR spectral features showed characteristic size dependence, and the line shapes were reproduced by using the layer-deconvolution model. Namely, the variations in the NMR spectra with particle size can be explained as due to the combined effect of the layer-by-layer variation of the s-type and d-type local density of states. However, the surface peak position of (195)Pt NMR spectra and the spin-lattice relaxation time of surface platinum atoms showed practically no change with the particle size variation. We conclude that there is a negligible difference in the surface electronic properties of these Pt/CB catalysts due to size variations and therefore, the ORR activities are not affected by the differences in the particle size.     

Designed nanostructured pt film for electrocatalytic activities by underpotential deposition combined chemical replacement techniques

Multiple-deposited Pt overlayer modified Pt nanoparticle (MD-Pt overlayer/PtNPs) films were deliberately constructed on glassy carbon electrodes through alternately multiple underpotential deposition (UPD) of Ag followed redox replacement reaction by Pt (II) cations. The linear and regular growth of the films characterized by cyclic voltammetry was observed. Atomic force spectroscopy (AFM) provides the surface morphology of the nanostructured Pt films. Rotating disk electrode (RDE) voltammetry and rotating ring-disk electrode (RRDE) voltammetry demonstrate that the MD-Pt overlayer/PtNPs films can catalyze an almost four-electron reduction of O(2) to H(2)O in air-saturated 0.1 M H(2)SO(4). Thus-prepared Pt films behave as novel nanostructured electrocatalysts for dioxygen reduction and hydrogen evolution reaction (HER) with enhanced electrocatalytic activities, in terms of both reduction peak potential and peak current, when compared to that of the bulk polycrystalline Pt electrode. Additionally, it is noted that after multiple replacement cycles, the electrocatalytic activities improved remarkably, although the increased amount of Pt is very low in comparison to that of pre-modified PtNPs due to the intrinsic feature of the UPD-redox replacement technique. In other words, the electrocatalytic activities could be improved markedly without using very much Pt by the technique of tailoring the catalytic surface. These features may provide an interesting way to produce Pt catalysts with a reliable catalytic performance as well as a reduction in cost.     

Adsorption of atomic hydrogen at a nanostructured electrode of polyacrylate-capped Pt nanoparticles in polyelectrolyte

Atomic hydrogen electrosorption is reported at crystallite sites of polyacrylate-capped Pt nanoparticles (d = 2.5 +/- 0.6 nm), by assembling nanostructured electrodes of polyacrylate-Pt nanocrystallites layer-by-layer in a cationic polyelectrolyte, poly(diallyldimethylammonium chloride). Cyclic voltammetry in 1 M H2SO4 revealed a strongly adsorbed hydrogen state and a weakly adsorbed hydrogen state assigned to adsorption at (100) and (110) sites of the modified nanocrystallites, respectively. Resolving hydrogen adsorption states signifies that surface capping by the carboxylate groups is not irreversibly blocking hydrogen adsorption sites at the modified Pt nanoparticle surface. Adsorption peak currents increased with increasing the number of layers up to 16 bilayers, indicating the feasibility of nanoparticle charging via interparticle charge hopping and the accessibility of adsorption states within the thickness of the nanoparticle/polyelectrolyte multilayers. Despite similarity in hydrogen adsorption in the cyclic voltammorgrams in 1 M H2SO4, negative shifts in adsorption potentials were measured at the nanocrystallite Pt-polyelectrolyte multilayers relative to a polycrystalline bulk Pt surface. This potential shift is attributed to a kinetic limitation in the reductive hydrogen adsorption as a result of the Pt nanoparticle surface modification and the polyelectrolyte environment.     

Au@Pt纳米粒子催化O2还原反应的电化学研究

以100 nm的Au粒子为核,抗坏血酸为还原剂,H2PtCl6·6H2O为前驱体,合成了Pt包Au核壳结构纳米粒子( Au@ Pt)及其修饰的玻碳(GC)电极(Au@ Pt/GC).采用旋转圆盘电极等常规电化学方法,比较了Au@ Pt/GC和商用碳载铂(Pt/C)修饰的玻碳电极(Pt/C/GC)催化O2还原反应活性及耐甲醇性能,发现Au@ Pt纳米粒子在铂用量很低的情况下,其催化O2还原反应活性仍与商用Pt/C相当,而且还具有优良的耐甲醇性能;其催化O2还原反应机理按O2直接还原成H2O的四电子历程进行.     

枝晶状Pt 薄膜的制备及其特殊红外效应

采用方波电位, 在10×10^-3 mol·L^-1 K₂PtCl₆+3×10^-4 mol·L^-1 PbAc₂+0.5 mol·L^-1 HClO₄溶液中, 于本体Pt 电极上电沉积制备出枝晶状Pt 薄膜. 随着沉积时间的增加, 枝晶长度逐渐由400 nm增加到900 nm, 且枝晶上的小晶粒(~10 nm大小)变得密集. 根据循环伏安(CV)曲线中氢吸脱附电量可得出Pt 薄膜具有中等粗糙度(C_r=9-36), 且电极表面的粗糙度随着沉积时间增加而增大. 观察到Pt 薄膜上吸附态CO的原位红外光谱具有明显的增强吸收效应, 当沉积时间为6 min 时所制得的枝晶Pt 电极的红外增强效应最大. CO呈现多种谱峰形状, 随着沉积时间的增加, 谱峰形状依次为左高右低的双极峰(类Fano 红外效应), 单极向下(表面增强红外吸收), 左高右低的双极峰, 单极向上(异常红外效应), 左低右高的双极峰和单极向下. 这表明纳米材料薄膜所呈现出的特殊红外性能, 与纳米材料的尺度和聚集状态等密切相关. 所制备的枝晶状Pt 薄膜有望为深入认识纳米材料的特殊红外性能提供一个良好的模型材料.     

Pt-Ru合金薄膜的电沉积制备及其电化学表面增强红外吸收光谱

在1mmol·L-1H2PtCl6+1mmol·L-1RuCl3+0.1mol·L-1H2SO4镀液中采用电沉积法在化学镀金膜的红外窗口Si反射面上制备Pt50Ru50合金电极.利用原子力显微镜(AFM)可以观察到制备的Pt50Ru50合金电极形貌呈现出100-200nm大小的颗粒.常规电化学分析方法得出该电极具有典型的合金特征,对CO和CH3OH具有很好的催化氧化作用.应用电化学现场衰减全反射表面增强红外光谱法(ATR-SEIRAS)可以观察到该电极上Pt位和Ru位上CO的振动谱峰,且表现出Pt-Ru二元金属良好的协同催化性能.     

Single-wall carbon nanotube-based proton exchange membrane assembly for hydrogen fuel cells

A membrane electrode assembly (MEA) for hydrogen fuel cells has been fabricated using single-walled carbon nanotubes (SWCNTs) support and platinum catalyst. Films of SWCNTs and commercial platinum (Pt) black were sequentially cast on a carbon fiber electrode (CFE) using a simple electrophoretic deposition procedure. Scanning electron microscopy and Raman spectroscopy showed that the nanotubes and the platinum retained their nanostructure morphology on the carbon fiber surface. Electrochemical impedance spectroscopy (EIS) revealed that the carbon nanotube-based electrodes exhibited an order of magnitude lower charge-transfer reaction resistance (R(ct)) for the hydrogen evolution reaction (HER) than did the commercial carbon black (CB)-based electrodes. The proton exchange membrane (PEM) assembly fabricated using the CFE/SWCNT/Pt electrodes was evaluated using a fuel cell testing unit operating with H(2) and O(2) as input fuels at 25 and 60 degrees C. The maximum power density obtained using CFE/SWCNT/Pt electrodes as both the anode and the cathode was approximately 20% better than that using the CFE/CB/Pt electrodes.     

Size-controlled synthesis of colloidal platinum nanoparticles and their activity for the electrocatalytic oxidation of carbon monoxide

Using polyvinylpyrrolidone (PVP) as a stabilizing agent, stable colloidal solutions of platinum nanoparticles of different size distributions have been prepared by reducing H2PtCl6 with hydrogen. The UV-vis adsorption peaks at 258 nm due to the adsorption of Pt(IV) species disappear completely, indicating that the Pt(IV) species has been used up and colloidal Pt has been formed. The electrodes have been prepared from aqueous Pt colloids and glassy carbon (GC). The effect of platinum particle size of Pt/GC catalyst electrode on the electrocatalytic oxidation of carbon monoxide has been investigated. The voltammetry shows that a higher potential is needed for the oxidation of absorbed carbon monoxide with a decrease of the platinum particle size for particle sizes larger than 1 nm. But for particle sizes smaller than 1 nm, the potential remains constant while the activity decreases with decreasing the size. The snowlike, well-dispersed, and highly ordered platinum nanoparticles demonstrate high activity in the oxidation reaction of carbon monoxide. The reason may be due to the geometric structure of platinum nanoparticles.     

Green synthesis of nanowire-like Pt nanostructures and their catalytic properties

We reported a simple and effective green chemistry route for facile synthesis of nanowire-like Pt nanostructures at one step. In the reaction, dextran acted as a reductive agent as well as a protective agent for the synthesis of Pt nanostructures. Simple mixing of precursor aqueous solutions of dextran and K₂PtCl₄ at 80 °C could result in spontaneous formation of the Pt nanostructures. Optimization of the experiment condition could yield nanowire-like Pt nanostructures at 23:1 molar ratio of the dextran repeat unit to K₂PtCl₄. Transmission electron microscopy results revealed that as-prepared nanowire-like Pt nanostructures consisted of individual Pt nanoparticles with the size range from 1.7 to 2.5 nm. Dynamic light scattering analysis indicated that as-prepared nanowire-like nanostructures have already formed in solution. The as-prepared nanowire-like Pt nanostructures were further characterized by UV-vis spectroscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. In addition, the ratio dependence and temperature dependence of this reaction have also been investigated. The as-prepared nanowire-like Pt nanostructures can be immobilized on glassy carbon electrodes using an electrochemical coupling strategy, and the resulting nanowire-like Pt nanostructures modified film exhibited an excellent electrocatalytic activity for the reduction of oxygen and the oxidation of NADH.     

3-D composite electrodes for high performance PEM fuel cells composed of Pt supported on nitrogen-doped carbon nanotubes grown on carbon paper

The 3-D composite electrodes consisting of Pt nanoparticles supported on nitrogen-doped carbon nanotubes (CN_x) grown directly on carbon paper were successfully prepared. The effect of the nitrogen atom incorporation in carbon nanotubes (CNTs) on the Pt nanoparticle dispersion and catalytic activities for the oxygen reduction reaction has been investigated. Compared to regular CNTs, highly dispersed Pt nanoparticles with smaller size (2–3 nm) and higher electrochemical Pt surface area as well as higher fuel cell performance were obtained for CN_x.     

On the influence of the metal loading on the structure of carbon-supported PtRu catalysts and their electrocatalytic activities in CO and methanol electrooxidation

PtRu (1:1) catalysts supported on low surface area carbon of the Sibunit family (S(BET) = 72 m(2) g(-1)) with a metal percentage ranging from 5 to 60% are prepared and tested in a CO monolayer and for methanol oxidation in H(2)SO(4) electrolyte. At low metal percentage small (<2 nm) alloy nanoparticles, uniformly distributed on the carbon surface, are formed. As the amount of metal per unit surface area of carbon increases, particles start coalescing and form first quasi two-dimensional, and then three-dimensional metal nanostructures. This results in a strong enhancement of specific catalytic activity in methanol oxidation and a decrease of the overpotential for CO monolayer oxidation. It is suggested that intergrain boundaries connecting crystalline domains in nanostructured PtRu catalysts produced at high metal-on-carbon loadings provide active sites for electrocatalytic processes.     

Effects of hydrogen peroxide on the electrochemical decomposition of layer-by-layer thin films composed of 2-iminobiotin-labeled poly(ethyleneimine) and avidin

The effects of hydrogen peroxide on the electrochemical decomposition of layer-by-layer thin films composed of 2-iminobiotin-labeled poly(ethyleneimine) (ib-PEI) and avidin were studied. An ib-PEI/avidin thin film prepared on the surface of a platinum (Pt) film-coated quartz resonator was electrochemically decomposed in the presence of hydrogen peroxide (H(2)O(2)) in the solution. The resonant frequency of the thin-film-deposited quartz resonator was increased upon application of electric potential (0.4-0.6 V vs Ag/AgCl) to the Pt layer, suggesting that the mass on the quartz resonator was decreased as a result of decomposition of the ib-PEI/avidin film. It was found that decomposition of the film is highly accelerated in the presence of H(2)O(2) compared to the decomposition in the same buffer solution without H(2)O(2), due to a pH change originating from electrochemical oxidation of H(2)O(2) on the Pt surface. The rate of electrochemical decomposition of the ib-PEI/avidin film was highly dependent on the concentration of H(2)O(2,) buffer capacity, and pH of the solution.     

Temperature dependence of oxygen reduction activity at Nafion-coated bulk Pt and Pt/carbon black catalysts

Oxygen reduction reaction (ORR) activity and H(2)O(2) formation at Nafion-coated film electrodes of bulk-Pt and Pt nanoparticles dispersed on carbon black (Pt/CB) were investigated in 0.1 M HClO(4) solution at 30 to 110 degrees C by using a channel flow double electrode method. We have found that the apparent rate constants k(app) (per real Pt active surface area) for the ORR at bulk-Pt (with and without Nafion-coating) and Nafion-coated Pt/CB (19.3 and 46.7 wt % Pt, d(Pt) = 2.6 to 2.7 nm) thin-film electrodes were in beautiful agreement with each other in the operation conditions of polymer electrolyte fuel cells (PEFCs), i.e., 30-110 degrees C and ca. 0.7 to 0.8 V vs RHE. The H(2)O(2) yield was 0.6-1.0% at 0.7-0.8 V on all Nafion-coated Pt/CB and bulk-Pt and irrespective of Pt-loading level and temperature. Nafion coating was pointed out to be a major factor for the H(2)O(2) formation on Pt catalysts modifying the surface property, because H(2)O(2) production was not detected at the bulk-Pt electrode without Nafion coating.     

Tuning the High‐Temperature Wetting Behavior of Metals toward Ultrafine Nanoparticles

The interaction between metal nanoparticles (NPs) and their substrate plays a critical role in determining the particle morphology, distribution, and properties. The pronounced impact of a thin oxide coating on the dispersion of metal NPs on a carbon substrate is presented. Al₂O₃‐supported Pt NPs are compared to the direct synthesis of Pt NPs on bare carbon surfaces. Pt NPs with an average size of about 2 nm and a size distribution ranging between 0.5 nm and 4.0 nm are synthesized on the Al₂O₃ coated carbon nanofiber, a significant improvement compared to those directly synthesized on a bare carbon surface. First‐principles modeling verifies the stronger adsorption of Pt clusters on Al₂O₃ than on carbon, which attributes the formation of ultrafine Pt NPs. This strategy paves the way towards the rational design of NPs with enhanced dispersion and controlled particle size, which are promising in energy storage and electrocatalysis.     

A simple Maxwell-Wagner-Butler-Volmer approach to the impedance of the hydrogen electrode in a nafion fuel cell

A simple one-dimensional model of the impedance of a hydrogen/Nafion electrode is set up combining the usual Maxwell-Wagner approach for linear, homogeneous, and isotropic media with the linearized Butler-Volmer equation for the interfacial, electrochemical reaction. Only one relaxation semicircle is normally seen in the Nyquist diagram, but a low-frequency arc may appear at high overvoltages. The model is described by only two dimensionless parameters (in addition to the dimensionless frequency). These parameters are related to the double-layer capacitance and to the interfacial electrochemical reaction rate, respectively. With some adjustments, the model can be used to explain the observed equilibrium impedance from 40 to 70 degrees C of a symmetric cell of the type C/Pt/H(2)|Nafion 117/H(2)/Pt/C. The hydrogen electrodes in this cell were built up as a disperse multiphase region (carbon, platinum grains, Nafion 117, and hydrogen gas) as commonly done in solid polymer fuel cells.     

Three-dimensional nanostructured carbon nanotube array/PtRu nanoparticle electrodes for micro-fuel cells

We have fabricated three-dimensional (3D) nanostructured carbon nanotube (CNT) array/PtRu nanoparticle (with the average molar percentage (26%) of Ru) electrodes using anodic aluminum oxide (AAO) templates for micro-fuel cells. 3D nanostructured CNT array was used to support PtRu nanoparticles to enhance the utilization efficiency of Pt. The 3D nanostructured CNT array/PtRu electrodes show the excellent catalytic activity and electrochemical stability of electro-oxidation of methanol. Their anodic current density is 10 times as high as that of PtRu thin-films, which could be explained in terms of the high specific surface area of 3D nanostructured CNT array supporting films and the uniform distribution of PtRu nanoparticles.     

Enhanced water photolysis with Pt metal nanoparticles on single crystal TiO2 surfaces

Two novel deposition methods were used to synthesize Pt-TiO(2) composite photoelectrodes: a tilt-target room temperature sputtering method and aerosol-chemical vapor deposition (ACVD). Pt nanoparticles (NPs) were sequentially deposited by the tilt-target room temperature sputtering method onto the as-synthesized nanostructured columnar TiO(2) films by ACVD. By varying the sputtering time of Pt deposition, the size of deposited Pt NPs on the TiO(2) film could be precisely controlled. The as-synthesized composite photoelectrodes with different sizes of Pt NPs were characterized by various methods, such as SEM, EDS, TEM, XRD, and UV-vis. The photocurrent measurements revealed that the modification of the TiO(2) surface with Pt NPs improved the photoelectrochemical properties of electrodes. Performance of the Pt-TiO(2) composite photoelectrodes with sparsely deposited 1.15 nm Pt NPs was compared to the pristine TiO(2) photoelectrode with higher saturated photocurrents (7.92 mA/cm(2) to 9.49 mA/cm(2)), enhanced photoconversion efficiency (16.2% to 21.2%), and increased fill factor (0.66 to 0.70). For larger size Pt NPs of 3.45 nm, the composite photoelectrode produced a lower photocurrent and reduced conversion efficiency compared to the pristine TiO(2) electrode. However, the surface modification by Pt NPs helped the composite electrode maintain higher fill factor values.