Catalytic activity and physicochemical properties of Ni-Au/Al<Subscript>3</Subscript>CrO<Subscript>6</Subscript> system for partial oxidation of methane to synthesis gas

This work is focused on the role of gold and Al₃CrO₆ support for physicochemical properties, and catalytic activity of supported nickel catalysts in partial oxidation of methane (POM). Catalysts, containing 5% Ni and 5% Ni-2% Au active phases dispersed on mono- (Al₂O₃, Cr₂O₃) and bi-oxide Al₃CrO₆ support, were investigated by TPR, BET and XRD methods, and the activity tests in POM reaction were carried out. Bimetallic Ni-Au catalysts dispersed on Al₃CrO₆ support remained highly stable and active. The amorphous binary oxide Al₃CrO₆ can stabilize considerable amount of Cr⁴⁺, Cr⁵⁺, and Cr⁶⁺ species in Ni-Au/Al₃CrO₆ catalyst network during its calcination in the air. Nickel supported on binary oxide Ni/Al₃CrO₆ can form Ni(III)CrO₃ bi-oxide phase in reductive conditions. During TPR H2 reduction of Ni-Au/Al₃CrO₆ catalyst chromium(II) oxide Cr(II)O phase is observed. After POM reaction the existence of bimetallic Au-Ni alloy was experimentally confirmed on mono-oxide Al₂O₃ support surface, but its formation was not identified on bioxide Al₃CrO₆ support. Published in Russian in Kinetika i Kataliz, 2009, Vol. 50, No. 1, pp. 149–156. The article is published in the original. Based on a report at the VII Russ. Conf. on Mechanisms of Catalytic Reactions (with international participation), St. Petersburg, July 2–8, 2006.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Study of <Emphasis Type="Italic">n</Emphasis>-hexane isomerization on Pt/SO<Subscript>4</Subscript>/ZrO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Effect of the state of platinum on catalytic and adsorption properties

The state of surface Pt atoms in the Pt/SO₄/ZrO₂/Al₂O₃ catalyst and the effect of the state of platinum on its adsorption and catalytic properties in the reaction of n-hexane isomerization were studied. The Pt-X/Al₂O₃ alumina-platinum catalysts modified with various halogens (X = Br, Cl, and F) and their mechanical mixtures with the SO₄/ZrO₂/Al₂O₃ superacid catalyst were used in this study. With the use of IR spectroscopy (CO_ads), oxygen chemisorption, and oxygen-hydrogen titration, it was found that ionic platinum species were present on the reduced form of the catalysts. These species can adsorb to three hydrogen atoms per each surface platinum atom. The specific properties of ionic platinum manifested themselves in the formation of a hydride form of adsorbed hydrogen. It is believed that the catalytic activity and operational stability of the superacid system based on sulfated zirconium dioxide were due to the participation of ionic and metallic platinum in the activation of hydrogen for the reaction of n-hexane isomerization.     

Review of Ag/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Reductant System in the Selective Catalytic Reduction of NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

Ag/Al₂O₃ is a promising catalyst for the selective catalytic reduction (SCR) by hydrocarbons (HC) of NO _x in both laboratory and diesel engine bench tests. New developments of the HC-SCR of NO _x over a Ag/Al₂O₃ catalyst are reviewed, including the efficiencies and sulfur tolerances of different Ag/Al₂O₃-reductant systems for the SCR of NO _x ; the low-temperature activity improvement of H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃; and the application of a Ag/Al₂O₃-ethanol SCR system with a heavy-duty diesel engine. The discussions are focused on the reaction mechanisms of different Ag/Al₂O₃-reductant systems and H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃. A SO₂-resistant surface structure in situ synthesized on Ag/Al₂O₃ by using ethanol as a reductant is proposed based on the study of the sulfate formation. These results provide new insight into the design of a high-efficiency NO _x reduction system. The diesel engine bench test results showed that a Ag/Al₂O₃-ethanol system is promising for catalytic cleaning of NO _x in diesel exhaust.     

Liquid phase selective hydrogenation of phenol to cyclohexanone over Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocatalyst under mild conditions

Highly monodispersed ruthenium nanoparticles were prepared via wet impregnation technique using RuCl₃ · nH₂O as a precursor. Ru nanoparticles were supported on Al₂O₃ to synthesize Ru nanocatalyst. The nanocatalyst was characterized by various techniques like XRD, SEM, TEM and BET analysis. The catalyst was used for hydrogenation of phenol under mild condition. The activity of the catalyst was checked by varying different parameters such as reaction temperature, time, H₂ partial pressure, metal loading and catalyst amount. The catalyst was recovered from product and reused up to four times without significant loss in its catalytic activity. After a reaction time of 1 h, Ru/Al₂O₃ nanocatalyst showed high reactivity (82% conversion) and selectivity to cyclohexanone (67%) at 80°C and 20 bar hydrogen pressure.     

Investigation of macro-/mesoporous Re<Subscript>2</Subscript>O<Subscript>7</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by a particle-template method for butylene metathesis

Macro-/mesoporous Al₂O₃ supports were prepared by using monodisperse polystyrene (PS) microspheres as a template. The pore volume and BET surface area of the Al₂O₃ supports increased considerably with increasing amounts of the PS microspheres; further investigation showed that PS template only increased the volume of macro-pores but did not change the volume of meso-pores or micro-pores. Macro-/mesoporous Re₂O₇/Al₂O₃ metathesis catalysts were prepared through loading Re₂O₇ onto the as-prepared macro-/mesoporous Al₂O₃ supports, and their catalytic performance was tested in a fixed-bed tubular reactor using the metathesis of normal butylenes as a probe reaction. The results showed that the prepared macro-/mesoporous Re₂O₇/Al₂O₃ catalyst had high activity with consistent selectivity; propylene and pentene accounted for more than 90 wt% of the metathesis products, while the amount of ethylene plus hexane was less than 10 wt%, the majority of which was hexane. These Re₂O₇/Al₂O₃ catalysts had not only higher activity, but also longer working life span and higher tolerance to carbon residues than conventional Re₂O₇/Al₂O₃ catalysts.     

Co-Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni-W/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Potential and prospects for use in hydrotreating of light cycle oil from catalytic cracking

Со-Мо/Al₂O₃ and Ni-W/Al₂O₃ catalysts were tested in hydrotreating of light cycle oil from catalytic cracking, of the straight-run gasoil, and of their mixture under typical hydrotreating conditions used in industry. The catalysts prepared using PMo₁₂ and PW₁₂ heteropoly acids exhibit high catalytic activity. The Со-Мо/Al₂O₃ catalyst is more active in hydrodesulfurization and hydrogenation of olefin and diene hydrocarbons, whereas the Ni-W/Al₂O₃ catalysts are more active in hydrogenation of mono- and polycyclic aromatic hydrocarbons. Comparison of the quality characteristics of the hydrogenizates obtained with the requirements of the technical regulations shows that the required levels of the sulfur content and cetane number of the hydrogenizates at practically accessible process parameters can be reached for mixtures of the straight-run gasoil and light cycle oil from catalytic cracking with high content of the latter component only when the process with the Со-Мо/Al₂O₃ system and Ni-W/Al₂O₃ catalysts is performed in two steps.     

Trimetallic NiMoW/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> hydrotreating catalyst based on H<Subscript>4</Subscript>SiMo<Subscript>3</Subscript>W<Subscript>9</Subscript>O<Subscript>40</Subscript> mixed heteropoly acid

Trimetallic NiMoW/Al₂O₃ catalyst was prepared using mixed H₄SiMo₃W₉O₄₀ heteropoly acid of Keggin structure and nickel citrate. Bimetallic NiMo/Al₂O₃ and NiW/Al₂O₃ catalysts based on H₄SiMo₁₂O₄₀ and H₄SiW₁₂O₄₀, respectively, were synthesized as reference samples. The use of mixed H₄SiMo₃W₉O₄₀ heteropoly acid as an oxide precursor allows the tungsten sulfidation degree and the degree of promotion of active phase particles to be increased. The hydrodesulfurization activity is enhanced as compared to NiW/Al₂O₃ catalyst. The synergistic enhancement of the activity of the NiMo₃W₉/Al₂O₃ catalyst relative to the bimetallic analogs is probably caused by formation of new mixed promoted active sites for direct desulfurization.     

Initiation behaviour in hydrogenation of pyrolysis gasoline over presulphided Ni-Mo-Zn/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst

A presulphided treatment was applied to the oxidic Ni-Mo-Zn/Al₂O₃ catalyst (nickel catalyst) in order to avoid thermal run-away during initiation of the hydrogenation of pyrolysis gasoline. The physico-chemical properties of the prepared oxidic nickel catalyst, the reduced and passivated (RP) nickel catalyst and the sulphided (RPS) nickel catalyst were characterised using N₂ adsorption-desorption, X-ray diffraction, temperature-programmed reduction (TPR) and X-ray photoelectron spectroscopy (XPS). The TPR results showed that the reducibility of the RP Ni-Mo-Zn/Al₂O₃ catalyst was improved over the oxidic nickel catalyst. The XPS spectra confirmed the binding energy of the RPS nickel catalyst to be higher than that of the oxidic nickel catalyst. The catalytic performance was evaluated on a fixed-bed reactor (reaction temperature between 30 °C and 70°C, at 2.8 MPa of total pressure and weight hourly space velocity of 2.0 h^?1, the volume of H₂/pyrogasoline = 200: 1). The rising temperature of the RPS nickel catalyst was almost 20°C lower than that of the oxidic nickel catalyst during the initial stage of the hydrogenation reaction. The results indicated that the RPS nickel catalyst exhibited better stability than the oxidic nickel catalyst during the start-up period, thereby providing a better selectivity in long-term operation.     

ZrO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> binary oxides as promising supports for palladium catalysts of hydrodechlorination

Deposited palladium catalysts of the hydrodechlorination of 1,3,5-trichlorobenzene were studied. Pure zirconium and aluminum oxides and ZrO₂-Al₂O₃ mixtures with 1, 5, and 10 mol % Al₂O₃ prepared by coprecipitation were used as supports. Palladium was deposited by the precipitation of its hydroxide on supports. Catalysts on binary supports (ZrO₂ + 1% Al₂O₃ and ZrO₂ + 5% Al₂O₃) exhibited higher activity and stability in hydrodechlorination compared with catalysts on pure supports. The suggestion was made that the high activity and stability of these systems in hydrodechlorination was related to the formation of binary oxide in the interaction of ZrO₂ with palladium oxide at the stage of annealing of the catalyst precursor. Binary oxide, which was a center of the activation of the C-Cl bond, was simultaneously a source of active hydrogen. The presence of various palladium states in catalysts was substantiated by the temperature programmed reduction method.     

No-Glycerol rapid heterogeneous biodiesel production on K<Subscript>2</Subscript>CO<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst by coupling process

Biodiesel containing almost no glycerol has been produced by coupling reaction carried out over K₂CO₃ supported by calcium oxide as solid base catalysts. The solid base catalysts synthesized by wet impregnation exhibit an exceedingly high activity in biodiesel production. It was found that the reaction time required for the highest yield of biodiesel, 99.2%, can be shortened to 30 min over K₂CO₃/Al₂O₃ under the optimum reaction conditions: 8: 1: 1 molar ratio of methanol/DMC/oil, 30 wt % K₂CO₃/Al₂O₃ catalyst, and 65°C reaction temperature. Solid basic catalysts examined in the study were characterized by BET surface area, XRD, CO₂-TPD, and SEM techniques. The strong interaction between K₂CO₃ and the support yields a new basic active site, which can be probably responsible for the high activity of K₂CO₃/Al₂O₃.     

Properties of the surface layer and catalytic activity of Ta<Subscript>2</Subscript>O<Subscript>5</Subscript> with Pt or Pd additives in the oxidation of hydrogen

The catalytic activity in the oxidation of hydrogen (in the gaseous state in the presence of excess oxygen) has been studied for samples of Pt(Pd)/Ta₂O_5−x, formed by reduction with hydrogen. The samples obtained had greater activity than the traditional catalysts Pt(Pd)/Al₂O₃. According to X-ray diffraction analysis and electron microscopic studies, Ta₂O_5−x becomes amorphous with the formation of more reduced non-stoichiometric oxygen-deficient tantalum oxides with a surface layer of catalyst. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 44, No. 3, pp. 180–185, May–June, 2008.     

The monooxidation of ethylene with hydrogen peroxide on the per-FTPhPFe<Superscript>3+</Superscript>OH/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> biomimetic

The gas-phase monooxidation of ethylene by hydrogen peroxide on a biomimetic heterogeneous catalyst (per-FTPhPFe³⁺OH/Al₂O₃) was studied under comparatively mild conditions. The biomimetic oxidation of ethylene with hydrogen peroxide was shown to be coherently synchronized with the decomposition of H₂O₂. Depending on reaction medium conditions, one of two desired products was formed, either ethanol or acetaldehyde. The kinetics and probable mechanism of ethylene transformation were studied.     

Catalytic properties of SnO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> compositions in total methane oxidation

Tin and titanium dioxides and their compositions were studied as catalysts for the reaction of complete oxidation of methane. The catalytic activity of the test samples was compared in terms of first-order reaction rate constants with reference to the unit surface area of a catalyst. The crystal structures and specific surface areas of the obtained compositions were characterized. The thermal stability of SnO₂ was investigated. Data on the temperature-programmed reduction of SnO₂ and the composition Sn_0.70Ti_0.30O₂ in hydrogen were given.     

The catalytic performance of different promoted iron catalysts on combined supports Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for carbon dioxide hydrogenation

Global warming, fossil fuel depletion and fuel price increases have motivated scientists to search for methods for the storage and reduction of the amount of greenhouse gases, especially CO₂. The hydrogenation process has been introduced as an emerging method of CO₂ capture and convertion into value-added products. In this study, new types of catalysts are introduced for CO₂ hydrogenation and are compared based on catalytic activity and product selectivity. The physical properties of the samples are specified using BET. Iron catalysts supported on γ-Al₂O₃ with different metal promoters (X = Ni, K, Mn, Cu) are prepared through the impregnation method. Moreover, Fe–Ni catalysts supported on HZSM5-Al₂O₃ and Ce–Al₂O₃ are synthesized. Samples are reduced by pure H₂ and involved in hydrogenation reaction in a fixed bed reactor (H₂/CO₂ = 3, total pressure = 10 MPa, temperature = 523 K, GHSV = 2000, 1250 nml/min). All catalysts provide high conversion in hydrogenation reactions and the results illustrate that the selectivity of light hydrocarbons is higher than that of methane and CO. It is found that Ni has a promoting effect on the conversion fluctuations throughout the reaction with 66.13% conversion. Using combined supported catalysts leads to enhancing catalytic performance. When Fe–Ni/γ–Al₂O₃—HZSM5 is utilized, CO₂ conversion is 81.66% and the stability of the Fe–Ni catalyst supported on Al₂O₃ and Ce–Al₂O₃ furthey improves.     

Study of Fe-doped V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> catalyst for an enhanced NH<Subscript>3</Subscript>-SCR in diesel exhaust aftertreatment

Selective catalytic reduction (SCR) with ammonia has been considered as the most promising technology, as its effect deals with the NO_X. Novel Fe-doped V₂O₅/TiO₂ catalysts were prepared by sol–gel and impregnation methods. The effects of iron content and reaction temperature on the catalyst SCR reaction activity were explored by a test device, the results of which revealed that catalysts could exhibit the best catalytic activity when the iron mass ratio was 0.05%. It further proved that the VTiFe (0.05%) catalyst performed the best in denitration and its NO_X conversion reached 99.5% at 270 °C. The outcome of experimental procedures: Brunauer–Emmett–Teller surface area, X-ray powder diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, temperature-programmed reduction and adsorption (H₂-TPR, NH₃-TPD) techniques showed that the iron existed in the form of Fe³⁺ and Fe²⁺ and the superior catalytic performance was attributed to the highly dispersed active species, lots of surface acid sites and absorbed oxygen. The modified Fe-doped catalysts do not only have terrific SCR activities, but also a rather broad range of active temperature which also enhances the resistance to SO₂ and H₂O.     

The influence of hydrogen-containing molybdenum and tungsten bronzes on the catalytic activity of palladium composite catalysts for the oxidation of H<Subscript>2</Subscript>, CO,and CH<Subscript>4</Subscript>

The influence of hydrogen-containing molybdenum and tungsten bronzes on the catalytic activity of palladium composite catalysts for the oxidation of H₂, CO, and CH₄ was studied. It was found that the composite catalysts containing H _x MO₃ phases (M = W or Mo), which were formed by the reduction of MoO₃ and WO₃ oxides with hydrogen in the presence of deposited Pd, showed higher catalytic activity in the oxidation of small molecules (H₂, CO, and CH₄) with excess oxygen than the traditional Pd/Al₂O₃ deposited catalyst with the same content of the deposited metal. It was shown that the thermal stability of the H _x MO₃ phases was the limiting factor influencing the activity of these composite catalysts.     

Facile synthesis of Fe@Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> core-shell nanowires as O<Subscript>2</Subscript> electrode for high-energy Li-O<Subscript>2</Subscript> batteries

Fe@Fe₂O₃ core-shell nanowires were synthesized via the reduction of Fe³⁺ ions by sodium borohydride in an aqueous solution with a subsequent heat treatment to form Fe₂O₃ shell and employed as a cathode catalyst for non aqueous Li-air batteries. The synthesized core-shell nanowires with an average diameter of 50–100 nm manifest superior catalytic activity for oxygen evolution reaction (OER) in Li-O₂ batteries with the charge voltage plateau reduced to ～3.8 V. An outstanding performance of cycling stability was also achieved with a cutoff specific capacity of 1000 milliampere hour per gram over 40 cycles at a current density of 100 mA g^?1. The excellent electrochemical properties of Fe@Fe₂O₃ as an O₂ electrode are ascribed to the high surface area of the nanowires’ structure and high electron conductivity. This study indicates that the resulting iron-containing nanostructures are promising catalyst in Li-O₂ batteries.     

Effect of Calcination Temperature and Pretreatment with Reaction Gas on Properties of Co/γ‐Al2O3 Catalysts for Partial Oxidation of Methane

The effects of calcination temperature and feedstock pretreatment on the catalytic performance of Co/γ‐Al₂O₃ catalysts were studied for partial oxidation of methane (POM) to synthesis gas, with emphasis on the role of feedstock pretreatment. The physicochemical properties of the catalysts were characterized by N₂ adsorption, X‐ray diffraction (XRD), transmission electron microscopy (TEM), H₂ temperature‐programmed reduction (H₂‐TPR), and Raman spectroscopy. The results showed that the pretreatment of the catalyst by reaction gas significantly improved the catalytic activity and stability for the POM reaction. On the other hand, the effect of calcination temperature was less significant. Although the initial activity was increased by an increased calcination temperature, the catalyst without the feedstock pretreatment suffered a rapid deactivation. The reaction‐atmosphere pretreatment was revealed as a process that mainly modified the surface structure of the catalyst. In that process, the formation of a CoAl₂O₄‐like compound led to high Co metal dispersion after reduction, and the transformation of the carrier into α‐Al₂O₃ occurred over the catalyst surface. Both the high dispersion of cobalt and the presence of α‐Al₂O₃ surface phase were assumed as the important factors resulting in an excellent catalytic performance in terms of high activity and high stability.     

Effect of cerium dioxide on the properties of monolithic CuO-ZnO-CeO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/cordierite catalysts in methanol decomposition

Cerium dioxide as a component of CuO-ZnO-CeO₂/Al₂O₃/cordierite catalysts stabilizes their action in the decomposition of methanol by preventing carbon deposition on the surface and facilitating hydrogen formation with selectivity and yield in the range 85–96%. The optimal indices for this reaction are obtained for a CeO₂-CuO/Al₂O₃/cordierite sample prepared using an ammonium precursor for cerium, (NH₄)₂Ce(NO₃)₆. This catalyst displays enhanced reductive capacity relative to the analogous CeO₂-CuO composition prepared using Ce(NO₃)₃·6H₂O.