SCALE ADAPTIVE SIMULATION OF FLOWS AROUND A CIRCULAR CYLINDER AT HIGH SUB-CRITICAL REYNOLDS NUMBER

借助γ-Re_θ转捩模型,实现了高亚临界雷诺数（Re=1.4×10⁵）下圆柱层流分离流动的尺度自适应模拟.统计平均结果表明数值计算和实验测量较为接近,尤其在圆柱后半段的分离区中,压力系数和实验符合得很好,误差主要源于分离点预测的不准确. 瞬态流动则显示,层流分离的剪切层中出现了展向不稳定,且在向下游的输运过程中不断增强,最后转捩为完全湍流. 在湍流分离模拟中,由于缺乏剪切层失稳的非定常性,SST-SAS 模型的尺度分辨能力变弱,因此在分离区以及下游尾迹中求解出的湍流尺度要明显较层流分离时大.     

剪切流及分离流结构和层流-湍流转捩的研究(成就和问题)

本文介绍了剪切层(边界层,Poiseujlle.流、分离流、尾流)中层流向湍流转捩过程的连续各阶段的实验研究结果,包括:给定流动对外部扰动的敏感性,产生的波(拟序结构)的线性发展,以及引起有序的层流流态破坏的非线性过程.     

流向磁场作用下圆柱绕流的直接数值模拟

绕流是托卡马克装置中液态包层内常见的流动形态,对流场与热量分布有着重要的影响.本文通过直接数值模拟(DNS),研究了不同磁场强度下$Re=3900$的圆柱绕流,分析了磁场强度对于湍流尾迹的影响.无磁场情况下,直接数值模拟的结果与前人的实验及模拟结果吻合很好.圆柱下游的尾迹中,随着流向距离的增大, 流向速度剖面逐渐从U型进化呈V型, 并慢慢趋于平缓,这表明尾迹中的流动结构受圆柱影响逐渐减小.圆柱后方两侧的剪切层中,由于Kelvin-Helmholtz不稳定性的影响,可以清晰地看到小尺度剪切层涡的脱落.通过对无磁场的计算结果施加流向磁场,本文计算了哈特曼数($Ha$)分别为20, 40和80的工况,以研究磁场效应对于湍流的影响.结果表明磁场较弱时,流动依然呈三维湍流状态.随着磁场增强, 近圆柱尾流区受磁场抑制明显,回流区被拉长,剪切层失稳位置向下游转移.圆柱后方的涡结构由于受到竖直方向洛伦兹力的挤压作用,随着哈特曼数的增加尾迹区域逐渐变窄.相比于无磁场情况的涡结构,由于磁场的耗散作用,相应的涡结构尺度变小.该研究不仅扩展了现有磁场下湍流运动的参数范围,对于液态包层的设计及安全运行同样具有重要的理论指导意义和工程应用价值.      

DIRECT NUMERICAL SIMULATIONS ON THE TURBULENT FLOW PAST A CONFINED CIRCULAR CYLINDER WITH THE INFLUENCE OF THE STREAMWISE MAGNETIC FIELDS1)

绕流是托卡马克装置中液态包层内常见的流动形态,对流场与热量分布有着重要的影响.本文通过直接数值模拟(DNS),研究了不同磁场强度下$Re=3900$的圆柱绕流,分析了磁场强度对于湍流尾迹的影响.无磁场情况下,直接数值模拟的结果与前人的实验及模拟结果吻合很好.圆柱下游的尾迹中,随着流向距离的增大, 流向速度剖面逐渐从U型进化呈V型, 并慢慢趋于平缓,这表明尾迹中的流动结构受圆柱影响逐渐减小.圆柱后方两侧的剪切层中,由于Kelvin-Helmholtz不稳定性的影响,可以清晰地看到小尺度剪切层涡的脱落.通过对无磁场的计算结果施加流向磁场,本文计算了哈特曼数($Ha$)分别为20, 40和80的工况,以研究磁场效应对于湍流的影响.结果表明磁场较弱时,流动依然呈三维湍流状态.随着磁场增强, 近圆柱尾流区受磁场抑制明显,回流区被拉长,剪切层失稳位置向下游转移.圆柱后方的涡结构由于受到竖直方向洛伦兹力的挤压作用,随着哈特曼数的增加尾迹区域逐渐变窄.相比于无磁场情况的涡结构,由于磁场的耗散作用,相应的涡结构尺度变小.该研究不仅扩展了现有磁场下湍流运动的参数范围,对于液态包层的设计及安全运行同样具有重要的理论指导意义和工程应用价值.     

超声速平板边界层斜波失稳转捩过程研究

以5阶迎风和6阶对称紧致格式混合差分求解三维可压缩滤波Navier-Stokes方程，对Mach 数为4.5, Reynolds数为10000的空间发展平板边界层湍流进行了大涡模拟. 时间推进采用 紧致存储3阶Runge-Kutta方法，亚格子尺度模型为修正Smagorinsky涡黏性模型. 通过在 入口边界叠加一对线性最不稳定第一模态斜波扰动，数值模拟得到了平板层流边界层失稳转 捩直至湍流的演化过程. 对流场转捩过程中瞬时量及统计平均量的分析表明，数值模拟结果 与理论吻合，得到的Y型剪切层、交替\Lambda涡结构以及转捩后期的发卡涡结构的发展 变化与相关文献结果一致，湍流流谱定性合理.     

绕振荡水翼流动及其转捩特性的数值计算研究

通过对比标准k-ω SST 湍流模型和基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型对绕振荡NACA66 水翼流动的数值计算结果与实验结果,对水翼振荡过程的水动力特性和流场结构变化进行了分析研究. 结果表明:与标准k-ω SST 湍流模型的数值计算结果相比,基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型能有效预测绕振荡翼型流场结构和水动力特性,捕捉流场边界层发生的流动分离和转捩现象;绕振荡水翼的流动过程可分为5 个特征阶段,当来流攻角较小时,在水翼前缘发生层流向湍流的转捩现象,水翼动力特征曲线出现变化拐点;随着来流攻角的增大,顺时针尾缘涡逐渐形成并向水翼前缘发展;当攻角较大时,前缘涡分离导致动力失速,水翼的动力特征曲线出现大幅波动;水翼处于顺时针向下旋转阶段,绕水翼的流动状态逐渐由湍流过渡为层流.      

绕振荡水翼流动及其转捩特性的数值计算研究简

通过对比标准k-ω SST 湍流模型和基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型对绕振荡NACA66 水翼流动的数值计算结果与实验结果,对水翼振荡过程的水动力特性和流场结构变化进行了分析研究. 结果表明：与标准k-ω SST 湍流模型的数值计算结果相比,基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型能有效预测绕振荡翼型流场结构和水动力特性,捕捉流场边界层发生的流动分离和转捩现象;绕振荡水翼的流动过程可分为5 个特征阶段,当来流攻角较小时,在水翼前缘发生层流向湍流的转捩现象,水翼动力特征曲线出现变化拐点;随着来流攻角的增大,顺时针尾缘涡逐渐形成并向水翼前缘发展;当攻角较大时,前缘涡分离导致动力失速,水翼的动力特征曲线出现大幅波动;水翼处于顺时针向下旋转阶段,绕水翼的流动状态逐渐由湍流过渡为层流.     

平片激振对分离剪切层的影响

实验研究了从前缘加入周期性扰动，对一个楔形体模型形成的含回流的分离剪切层影响问题，实验雷诺数Ｒｅ＿ｃ＝６．６７×１０￣５．揭示了含回流的分离剪切层在未激振与激振状态下峰值中心频率的演化特征；探讨了分离剪切层局部响应频率与激振基本频率的关系。研究表明：激振作用改变了分离剪切层峰值中心频率向下游的演化过程，增加了湍流脉动强度和湍流混合，加快了分离剪切层增长，致使剪切层中心线下弯，从而分离剪切层再附或分离泡缩短。     

激波与转捩边界层干扰非定常特性数值分析

激波与边界层干扰的非定常问题是高速飞行器气动设计中基础研究内容之一.以往研究主要针对层流和湍流干扰,在分离激波低频振荡及其内在机理方面存在着上游机制和下游机制两类截然不同的理论解释.分析激波与转捩边界层干扰下非定常运动现象有助于进一步加深理解边界层状态以及分离泡结构对低频振荡特性的影响规律,为揭示其产生机理指出新的方向.采用直接数值模拟方法对来流马赫数2.9,24?压缩拐角内激波与转捩边界层干扰下激波的非定常运动特性进行了数值分析.通过在拐角上游平板特定的流向位置添加吹吸扰动激发流动转捩,使得进入拐角的边界层处于转捩初期阶段.在验证了计算程序可靠性的基础上,详细分析了转捩干扰下激波运动的间歇性和振荡特征,着重研究了分离泡展向三维结构对激波振荡特性的影响规律,最后还初步探索了转捩干扰下激波低频振荡产生的物理机制.研究结果表明:分离激波的非定常运动仍存在强间歇性和低频振荡特征,其时间尺度约为上游无干扰区内脉动信号特征尺度的10倍量级;分离泡展向三维结构不会对分离激波的低频振荡特征产生实质影响.依据瞬态脉动流场的低通滤波结果,转捩干扰下激波低频振荡的诱因来源于拐角干扰区下游,与流场中分离泡的收缩/膨胀运动存在一定的关联.     

绕椭球的低速流动研究

理解和预测绕椭球的流动对指导飞行器和潜艇等交通工具的设计具有很强的工程意义. 近年来, 针对椭球绕流开展了大量的实验和数值模拟研究. 对有攻角下椭球绕流分离的定性描述和定量研究, 促进了对三维分离的辨识和拓扑研究. 文章对流场特性进行了分析, 介绍了分离对气动力、噪声、尾迹的影响, 以及实验条件对流动的影响. 上述定常流动与非定常机动过程之间存在明显差异, 非定常机动过程不能作为定常或准定常问题处理, 在机动过程中, 分离出现明显延迟, 气动力出现明显变化. 随后介绍了数值模拟在求解绕椭球流动中的进展, 当前求解雷诺平均的N-S方程湍流模式仍然是解决绕椭球大范围分离流动的主要工程方法, 大涡模拟和分离涡模拟等也逐渐得到了广泛应用. 受限于计算能力, 直接数据模拟只能用于较低雷诺数, 在高雷诺数流动中还不适用. 非定常机动过程的数值模拟较定常状态, 与实验结果的差距要大一些. 最后, 介绍了对椭球绕流场转捩的研究进展, 对T-S转捩与横流转捩的机理和辨识已经较为准确, 数值模拟结果与实验结果基本相符, 但对再附转捩的认识还不够清晰, 尤其是迎风面, 因此椭球绕流转捩的研究还需要依靠实验.      

DNS of a Laminar Separation Bubble in the Presence of Oscillating External Flow

A three-dimensional Direct Numerical Simulation (DNS) of a laminar separation bubble in the presence of oscillating flow is performed. The oscillating flow induces a streamwise pressure gradient varying in time. The special shape of the upper boundary of the computational domain, together with the oscillating pressure gradient causes the boundary layer flow to alternately separate and re-attach. When the inflow decelerates, the shear layer starts to separate and rolls up. Simultaneously the flow becomes 3D. After a transient period, the phase-averaged reverse flow inside the separation bubble reaches speeds ranging from 20 up to 150% of the free-stream velocity. During these phases, the flow is absolutely unstable and self-sustained turbulence can exist. When the inflow starts to accelerate, a spanwise roll of turbulent flow is shed from the shear layer. Shortly after this, the remainder of the separation bubble moves downstream and rejoins with the shed turbulent roll. During the flow-acceleration phase, a patch of laminar boundary layer flow is obtained. Along the flat plate, a series of turbulent patches of flow travelling downstream, separated by laminar flow can be observed, reminiscent of boundary layer flow in a turbine cascade with periodically appearing free-stream disturbances.     

High-Velocity Laminar and Turbulent Flow in Porous Media

We model high-velocity flow in porous media with the multiple scale homogenization technique and basic fluid mechanics. Momentum and mechanical energy theorems are derived. In idealized porous media inviscid irrotational flow in the pores and wall boundary layers give a pressure loss with a power of 3/2 in average velocity. This model has support from flow in simple model media. In complex media the flow separates from the solid surface. Pressure loss effects of flow separation, wall and free shear layers, pressure drag, flow tube velocity and developing flow are discussed by using phenomenological arguments. We propose that the square pressure loss in the laminar Forchheimer equation is caused by development of strong localized dissipation zones around flow separation, that is, in the viscous boundary layer in triple decks. For turbulent flow, the resulting pressure loss due to average dissipation is a power 2 term in velocity.     

Loss Production Mechanisms in a Laminar Separation Bubble

The present paper reports the results of a detailed experimental study, carried out by means of a two-component Laser Doppler Velocimeter, aimed at investigating the loss generation mechanisms induced by laminar separation bubble and transition process. Measurements have been performed along a flat plate installed within a double contoured test section, designed to produce an adverse pressure gradient typical of Ultra-High-Lift turbine blade profiles, which induces the formation of a laminar separation bubble. Results were detailed enough to allow calculating laminar and turbulent deformation works in the separated flow region. Normal and shear contributions of both viscous and turbulent deformation works have been analyzed and employed to explain the generation of total pressure losses in the separated flow region, where the generation and amplification of Kelvin–Helmholtz instability induces the separated shear layer roll-up, thus the bubble reattachment. Results obtained for different Reynolds number conditions have been employed for the formulation of a loss scaling procedure involving the separated shear layer thickness, which is directly correlated to the dynamics of Kelvin–Helmholtz roll-up vortices.     

Turbulent separated reattached flow in a two-dimensional curved-wall diffuser

A turbulent separation-reattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter. The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel. At the inlet of the diffuser, Reynolds number based on the diffuser height is 1.2×10⁵ and the velocity is 25.2m/s. The results of experiments are presented and analyzed in new defined streamline-aligned coordinates. The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress. A scale is formed using the maximum Reynolds shear stresses. It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law exists in the forward shear flow. Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model. The length scale is taken from that developed by Schofield and Perry. The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield-Perry velocity scale as well as the edge velocity of the boundary layer. The results of these experiments are presented in this paper.     

Visualizing supersonic inlet duct unstart using planar laser Rayleigh scattering

Planar laser Rayleigh scattering (PLRS) from condensed CO₂ particles is used to visualize flow structure in a Mach 5 wind tunnel undergoing unstart. Detailed flow features such as laminar/turbulent boundary layers and shockwaves are readily illustrated by the technique. A downstream transverse air jet, inducing flow unchoking downstream of the jet, is injected into the free stream flow of the tunnel, resulting in tunnel unstart. Time sequential PLRS images reveal that the boundary layer growth/separation on a surface with a thick turbulent boundary layer, initiated by the jet injection, propagates upstream and produces an oblique unstart shock. The tunnel unstarts upon the arrival of the shock at the inlet. In contrast, earlier flow separation on the opposite surface, initially supporting a thin laminar boundary layer, is observed when a jet induced bow shock strikes that surface. The resulting disturbance to this boundary layer also propagates upstream and precedes the formation of an unstart shock.     

A hybrid RANS/LES approach with scale-adaptive capabilities for highly separated flows

A new hybrid RANS/LES approach with scale-adaptive capabilities is developed. The blending function in the SST model is adopted to prevent the invasion of the von Karman length scale to the RANS region, and the compressibility correction proposed by Wilcox is incorporated to produce a realistic shear layer development in compressible flows. The new model is validated for a subcritical flow past a circular cylinder and a supersonic base flow. Time-averaged turbulent statistics predicted by the new model show fairly good agreement with the experimental data, slight improvements over DES simulations, and are much better than SAS results. The main advantage of the new model over the DES method is that the distribution of the blending function reflects local vortex structures instead of grid spacing in the turbulent wake. The sequence of the effect intensity of the compressibility correction from strong to weak is SAS, the new model and DES.     

The effect of boundary layer fluctuations on the streamwise vortex structure in simulated plane turbulent mixing layers

This paper details the influence of the magnitude of imposed inflow fluctuations on Large Eddy Simulations of a spatially developing turbulent mixing layer originating from laminar boundary layers. The fluctuations are physically-correlated, and produced by an inflow generation technique. The imposed high-speed side boundary layer fluctuation magnitude is varied from a low-level, up to a magnitude sufficiently high that the boundary layer can be considered, in a mean sense, as nominally laminar. Cross-plane flow visualisation shows that each simulation contains streamwise vortices in the laminar and turbulent regions of the mixing layer. Statistical analysis of the secondary shear stress reveals that mixing layers originating from boundary layers with low-level fluctuations contain a spatially stationary streamwise structure. Increasing the high-speed side boundary layer fluctuation magnitude leads to a weakening of this stationary streamwise structure, or its removal from the flow entirely. The mixing layer growth rate reduces with increasing initial fluctuation level. These findings are discussed in terms of the available experimental data on mixing layers, and recommendations for both future experimental and numerical research into the mixing layer are made.     

Effect of Streamline Curvature on Three-Dimensionality of Transitional Near-Wall Flow in a Linear Hydrofoil Cascade: A DNS Investigation

Flow, Turbulence and Combustion - The laminar flow on a curved surface transits to turbulent induced by streamline curvature which generates pressure gradient field and separated shear layer flow....     

Flow past a cylinder: shear layer instability and drag crisis

Flow past a circular cylinder for Re=100 to 10⁷ is studied numerically by solving the unsteady incompressible two‐dimensional Navier–Stokes equations via a stabilized finite element formulation. It is well known that beyond Re ～ 200 the flow develops significant three‐dimensional features. Therefore, two‐dimensional computations are expected to fall well short of predicting the flow accurately at high Re. It is fairly well accepted that the shear layer instability is primarily a two‐dimensional phenomenon. The frequency of the shear layer vortices, from the present computations, agree quite well with the Re^0.67 variation observed by other researchers from experimental measurements. The main objective of this paper is to investigate a possible relationship between the drag crisis (sudden loss of drag at Re ～ 2 × 10⁵) and the instability of the separated shear layer. As Re is increased the transition point of shear layer, beyond which it is unstable, moves upstream. At the critical Reynolds number the transition point is located very close to the point of flow separation. As a result, the shear layer eddies cause mixing of the flow in the boundary layer. This energizes the boundary layer and leads to its reattachment. The delay in flow separation is associated with narrowing of wake, increase in Reynolds shear stress near the shoulder of the cylinder and a significant reduction in the drag and base suction coefficients. The spatial and temporal power spectra for the kinetic energy of the Re=10⁶ flow are computed. As in two‐dimensional isotropic turbulence, E(k) varies as k^?5/3 for wavenumbers higher than energy injection scale and as k^?3 for lower wavenumbers. The present computations suggest that the shear layer vortices play a major role in the transition of boundary layer from laminar to turbulent state. Copyright © 2004 John Wiley & Sons, Ltd.