环氧改性水性聚氨酯乳液的制备及其膜性能

以聚己内酯二元醇(CAPA)为软段,异佛尔酮二异氰酸酯(IPDI)和六亚甲基二异氰酸酯(HDI)为硬段,环氧树脂E-44为大分子交联剂,经相转化法合成了一系列环氧树脂改性负离子水性聚氨酯(EPPU)自乳化乳液,并制备了改性水性聚氨酯的固化膜.通过FTIR、TGA及接触角、力学性能测试对聚合物结构及其膜性能进行了研究.通过原子力显微镜(AFM)观察膜表面形态和表面粗糙度.乳液粒径及粒径分布通过动态激光光散射法(DLLS)测定.FTIR分析表明环氧树脂的羟基和环氧基都参与了发应.TGA表明,环氧树脂的加入可以提高聚氨酯的热稳定性.随着w(E-44)增大,改性聚氨酯膜的拉伸强度得到改善,断裂伸长率减小.随着w(E-44)增大,乳液粒径增大,薄膜的接触角增大,改性后的PU膜表面光滑度下降,拒水性增强.     

水性环氧树脂的研制及其固化性能研究

采用端甲氧基聚乙二醇、马来酸酐、E-44环氧树脂合成了反应型环氧树脂乳化剂MeO-PEG-Ma-E-44,以相反转乳化技术制备E-44水性环氧树脂,研究了工艺条件对其性能的影响。结果表明:酯化率达98.5%的MeO-PEG-Ma-E-44,用量为E-44的ω=16.5%-20%得到的水性环氧树脂乳液最稳定。DSC和TG分析结果表明:乳化前后的E-44环氧树脂都能室温条件2h内很好的固化,固化后热性能基本不变,分解温度约在380℃,热失重率89%,其玻璃转变温度有所降低,韧性有所提高,其它性能基本不受影响。     

水性环氧树脂固化剂的制备及其涂膜性能研究

采用二乙烯三胺(DETA)与聚丙二醇二缩水甘油醚(PPGDGE)反应合成出DETA-PPGDGE-DETA型的多元胺加成物,然后再用一定比例环氧树脂E-20封端加成,制备出了水性环氧树脂固化剂。红外光谱(IR)及飞行时间质谱(TOF-MS)验证了该水性环氧固化剂的结构。考察了不同反应条件对固化剂结构与性能的影响,结果表明,二乙烯三胺/聚丙二醇二缩水甘油醚环氧基物质的量比为10∶1,用沸点稍高的二乙二醇丁醚(DGBE)将体系中残留小分子DETA蒸除干净,环氧树脂E-20封端20%伯胺氢时,固化剂与环氧乳液混合后的涂膜性能最佳。     

乳化剂对阳离子乳液聚合及乳胶粒性能的影响

以苯乙烯、丙烯酸丁酯为非离子单体,甲基丙烯酰氧乙基三甲基氯化铵（DMC）为阳离子单体,偶氮二异丁基脒盐酸盐（AIBA）为引发剂,十六烷基三甲基氯化铵（CTAC）和乙撑基双（十六烷基二甲基氯化铵）（G16—2—16）为乳化剂,采用半连续种子乳液聚合法进行阳离子乳液聚合。探讨了乳化剂的分子结构和用量对反应速率、单体转化率以及乳胶粒粒径、Zeta电位等的影响。结果表明：乳化剂的用量越大,反应速率越大,单体转化率越高,而乳胶粒粒径越小;使用G16—2—16作乳化剂时,单体转化率较高,乳胶粒粒径较大,Zeta电位较高。     

非离子型水性环氧乳液的制备工艺及性能研究

采用实验室自制的非离子型高分子乳化剂通过相反转法对环氧树脂E-20进行乳化分散来制备水性环氧乳液,对环氧树脂乳化的工艺条件进行了优化研究,并对不同条件的乳液进行了综合性能的分析。具体工艺条件包括:环氧树脂乳液体系中各物料的比例关系,乳化时体系的温度和搅拌速度。结果表明,乳化剂含量为12.5%,助溶剂含量为11.5%,乳化温度为30℃,搅拌速度为300r/min时,乳液的稳定性及漆膜的综合性能(包括漆膜的力学性能和抗腐蚀性能)佳。     

环氧树脂-聚醚-三乙烯四胺嵌段聚合物的表面活性

对含有环氧树脂分子链段、聚醚链段及三乙烯四胺链段的系列多嵌段聚合物(TETA-DGEPG-EPON828、TETA-DGEPG-EPON834及TETA-DGEPG-EPON1001加成物)进行了合成与表征. 其HLB的估算值分别为16.6、15.8和13.0,浊点分别为91.0、89.0和81.0 ℃. 合成物能将水溶液表面张力从74 mN/m降低至36.4～39.4 mN/m. 理化性能研究结果表明,TETA-DGEPG-EPON834具有优良的水溶性和良好的表面活性,用它作为相反转乳化剂,可制备出稳定的纳米级CARDURA E-10封端的EPON828-TETA加成物水性环氧固化剂胺基分散体乳液.     

醇醚糖苷与纳米膨润土颗粒稳定乳状液的协同作用

以表面活性剂醇醚糖苷(AEG)和纳米膨润土颗粒(NPT-2)为乳化剂,制备了油酸甲酯乳状液,考察了AEG与NPT-2的配比对乳液体系稳定性和乳液粒径的影响,并通过表面张力和zeta电位测量对二者复配稳定乳液的机理进行了讨论。结果表明,单一使用表面活性剂AEG或者纳米膨润土颗粒NPT-2均不能得到稳定的油酸甲酯乳状液,将二者复配则乳液的稳定性有显著提高。固定AEG量逐渐增加NPT-2乳液粒径先增大后又减小,固定NPT-2量逐渐增加AEG,乳液体系粒径逐渐变小;AEG与NPT-2复配前后体系的表面张力曲线"滞后"现象及zeta电位的升高表明,AEG分子在纳米颗粒NPT-2上发生了吸附,协同稳定乳状液。     

纳米尺度超声显影微囊的制备及性能表征简

采用双乳液-溶剂挥发法制备了内部包封氟碳液体的聚乳酸-甲氧基聚乙二醇两嵌段共聚物(MePEG-b-PLA)基超声显影纳米微囊;用2种不同嵌段比的MePEG-b-PLA共聚物研究共聚物组成与纳米囊性能的关系;选用聚乙烯醇(PVA)、羧甲基葡聚糖(CMG)和壳聚糖(CS) 3种乳化剂对纳米囊表面进行亲水性修饰. 对所制备纳米囊的粒径、Zeta电位、形貌和水溶液稳定性进行了表征. 结果表明,利用质量分数为1%的PVA和质量分数为1%的CMG组成的复配乳化剂和m(MePEG)：m(PLA)= 1：3的聚合物制得的纳米囊的平均粒径为432.9 nm,水溶液稳定性优良. 利用超声仪对纳米囊体外超声显影性能进行研究,结果表明,所得聚乳酸-甲氧基聚乙二醇纳米囊具有更好的中心成像区域灰度值和更持久的体外超声显影效果. 结合3-(4,5-二甲基噻唑-2)-2,5-二苯基四氮唑溴盐(MTT)比色法研究证实该纳米囊具有低细胞毒性. 在超声影像学领域具有良好的应用前景.     

超浓反相聚合物乳液的粒径双峰分布特征及其与稳定性的关系

以丙烯酸、丙烯酰胺、2-丙烯酰胺基-2-甲基丙磺酸作为混合单体,Span-80和Tween-60作为复合乳化剂、采用氧化还原引发体系在常温下引发聚合,制备了稳定的超浓反相聚合物乳液,同时制备了低分散相体积分数的普通乳液及由普通乳液离心得到的超浓反相聚合物乳液作为对比研究.用显微镜观察了乳胶粒的形态,统计计算了乳胶粒粒径...     

高固含量丙烯酸酯的微乳液聚合

采用半连续滴加预乳液的微乳液聚合法,合成出聚合物质量分数40%、乳化剂质量分数2.5%的丙烯酸酯微乳液. 考察了单体滴加速度、乳化剂种类及其用量、电解质用量、温度和搅拌等因素对乳液粒径及性能的影响. 研究表明,聚合在相当于Winsor-Ⅰ型的聚合体系中进行,由纯单体相(滴入的单体)和O/W微乳相构成,上层单体只起储存库的作用,它在缓慢的搅拌帮助下扩散进入微乳相中,只要微乳液液面上补加的单体不扰动微乳液的平衡,即不会产生粗粒子. 单体滴加时间控制在4 h,选择质量分数为2.5%的Dowfax2A1/OP-10乳化体系,NaHCO3质量分数为0.16%,反应温度控制在75～80 ℃,搅拌速度控制在150 r/min,可使聚合反应平稳进行,得到了m(聚合物)∶m(乳化剂)=15∶1的丙烯酸酯微乳液.     

环氧树脂水基分散体系的相反转乳化

以聚乙二醇－邻苯二甲酸酐－环氧树脂Ｅ－４４多元嵌段共聚体为乳化剂,将环氧树脂Ｅ－４乳化成水包油的稳定水基乳液。用乳液体系电导率和粘度的变化表征了相反转乳化过程。研究了乳化剂浓度、三元多嵌段共聚体中亲水嵌段分子量和乳化温度对相反转乳化过程的影响。实验结果表明,体系在较高乳化剂浓度（９．１％）下为完全相反转,在低乳化剂浓度（４．１％）下为不完全相反转。相反转时水与环氧树脂Ｅ－４４的重量比值随乳化剂浓度     

影响环氧树脂E-44相反转乳化的因素

研究了乳化剂的HLB值、乳化剂浓度、乳化温度、搅拌强度对环氧树脂E-44相反转乳化中临界含水量Rf值与乳状液稳定性的影响,探讨了环氧树脂E-44相反转机理。实验结果表明环氧树脂E-44从W/O向O/W相反转的发生与乳化剂的HLB值与浓度、乳化温度、搅拌强度等因素都有关,其Rf值随着乳化条件的不同是动态变化的。     

Amphiphilic hydrogel nanoparticles. Preparation, characterization, and preliminary assessment as new colloidal drug carriers

Inverse emulsion photopolymerization of acrylated poly(ethylene glycol)-bl-poly(propylene glycol)-bl-poly(ethylene glycol) and poly(ethylene glycol) was successfully employed to prepare stable, cross-linked, amphiphilic nanoparticles. Even at low emulsifier concentrations (2%) and high water-to-hexane weight ratios (35/65), the stability of the inverse emulsion allowed for the formation of well-defined colloidal material. Inverse emulsion characteristics and polymerization conditions could be controlled to vary the size of the nanoparticles between 50 and 500 nm. The presence of hydrophobic nanodomains within these otherwise hydrophilic nanoparticles was verified by using pyrene as a microenvironmentally sensitive probe. The hydrophobic poly(propylene glycol)-rich domains appear to be suitable for incorporation of hydrophobic drugs, encapsulating Doxorubicin up to 9.8% (w/w). We believe that the complex nano-architecture of these materials makes them a potentially interesting colloidal drug delivery carrier system and that the method should be useful for a number of amphiphilic macromolecular precursors.     

乙二醇二缩水甘油醚的合成及作为阳离子型紫外光固化稀释剂性能研究

以三氟化硼乙醚络合物为催化剂,以氢氧化钠为成环反应的闭环剂,利用乙二醇和环氧氯丙烷为原料合成了乙二醇二缩水甘油醚.研究了催化剂三氟化硼乙醚络合物用量、环氧氯丙烷和乙二醇摩尔比、氢氧化钠和乙二醇摩尔比,以及成环反应温度这些因素对合成反应的影响.结果表明较好的合成反应条件是:三氟化硼乙醚络合物质量分数为0.40%,环氧氯丙烷和乙二醇较佳摩尔比为2.4:1,氢氧化钠和乙二醇较佳摩尔比为2.2:1,较佳的成环反应温度为30℃.同时,把乙二醇二缩水甘油醚作为稀释剂加入到环氧树脂E-51中,利用三芳基锍鎓六氟锑酸盐作为引发剂,制备了阳离子型紫外光固化涂料,其紫外光固化膜的拉伸强度为46.25MPa,杨氏模量为1487.26MPa,断裂伸长率为6.27%.     

St-BA copolymer emulsions prepared by using novel cationic maleic dialkyl polymerizable emulsifier

A novel polymerizable cationic dialkyl maleic emulsifier with 12 carbon atomic hydrophobic chain lengths (R = C₁₂H₂₅) as well as a similar conventional cationic emulsifier, cetyltrimethyl ammonium bromide (CTAB) as comparison, were investigated in batch emulsion copolymerization of styrene and butyl acrylate. A series of emulsion samples have been prepared with two kinds of emulsifiers, and their properties have been characterized and compared. Compared with the emulsions prepared by using cationic CTAB emulsifier, the emulsions prepared by using maleic emulsifier have larger particle size, higher surface tension, generally more stable on certain electrolytes and less water absorption ratio as 34.87% after 30 days vs. 50.65% for the emulsion containing CTAB emulsifier. Whereas, the maleic emulsifier itself has lower CMC and surface tension compared with cationic CTAB emulsifier.     

Toward designer magnetite/polystyrene colloidal composite microspheres with controllable nanostructures and desirable surface functionalities

An effective method was developed for synthesizing magnetite/polymer colloidal composite microspheres with controllable variations in size and shape of the nanostructures and desirable interfacial chemical functionalities, using surfactant-free seeded emulsion polymerization with magnetite (Fe(3)O(4)) colloidal nanocrystal clusters (CNCs) as the seed, styrene (St) as the monomer, and potassium persulfate (KPS) as the initiator. The sub-micrometer-sized citrate-acid-stabilized Fe(3)O(4) CNCs were first obtained via ethylene glycol (EG)-mediated solvothermal synthesis, followed by 3-(trimethoxysilyl)propyl methacrylate (MPS) modification to immobilize the active vinyl groups onto the surfaces, and then the hydrophobic St monomers were polymerized at the interfaces to form the polymer shells by seeded emulsion radical polymerization. The morphology of the composite microspheres could be controlled from raspberry- and flower-like shapes, to eccentric structures by simply adjusting the feeding weight ratio of the seed to the monomer (Fe(3)O(4)/St) and varying the amount of cross-linker divinyl benzene (DVB). The morphological transition was rationalized by considering the viscosity of monomer-swollen polymer matrix and interfacial tension between the seeds and polymer matrix. Functional groups, such as carboxyl, hydroxyl, and epoxy, can be facilely introduced onto the composite microspheres through copolymerization of St with other functional monomers. The resultant microspheres displayed a high saturation magnetization (46 emu/g), well-defined core-shell nanostructures, and surface chemical functionalities, as well as a sustained colloidal stability, promising for further biomedical applications.     

荧光探针法研究乳化剂对硅/丙核壳乳液聚合行为的影响

用荧光探针(芘)法测定了十二烷基硫酸钠(SDS)、烷基酚聚氧乙烯醚(OP-10),以及复配乳化剂的临界胶束浓度(CMC),并首次把荧光探针技术应用到硅/丙核壳乳液聚合反应的研究中.利用芘的I₁/I₃值,结合胶束微环境的极性变化规律和乳液聚合机理,探讨了乳化剂对聚合反应的影响.结果表明,荧光探针(芘)法可用于研究硅/丙乳液的聚合行为和确定乳化剂配比.通过粒径分析、透射电镜(TEM)对产品的结构进行了表征.     

稳态荧光探针法研究复配乳化剂的聚集行为

采用荧光探针技术,根据芘的第一振动峰I₁(373 nm)与第三振动峰I₃(384 nm)荧光强度的比值(I₁/I₃)随乳化剂浓度的变化,对十二烷基磺酸钠(AS)与壬基酚聚氧乙烯醚(Oπ-10)复配乳化剂的CMC值进行了测定,并与十二烷基磺酸钠(AS),壬基酚聚氧乙烯醚(Oπ-10)的CMC值进行了比较,结果表明复配乳化剂的CMC介于两者之间.以二苯甲酮为猝灭剂,用稳态荧光法测定了不同比例复配乳化剂的胶束聚集数,实验结果表明,复配乳化剂浓度为4—9倍CMC时,测定的胶束聚集数随复配乳化剂浓度的增大而线性增大;且Oπ-10:AS<2:1时,随着复合乳化剂中Oπ-10比例的增大,复配乳化剂胶束聚集数增大.利用芘的I₁/I₃值,结合胶束微环境的极性变化规律,探讨了复配乳化剂的聚集行为对硅丙乳液聚合物的影响.     

Effect of preparation conditions on properties of polylactide and polystyrene and their composite microparticles made by emulsion solvent evaporation method

In this study, polylactide and polystyrene microparticles have been prepared by emulsion solvent evaporation method. Effects of polymer nature, stirring speed, emulsifier, and concentration of the components on the size, size distribution and morphology of polymeric microparticles have been investigated. 11-Acryloyl-aminoundecanoic acid and its polymer poly(11-acryloyl-aminoundecanoic acid) were tested for comparison with traditional emulsifiers such as sodium dodecylsulfate. Interfacial tension measurement was applied to compare these emulsifiers. Dynamic light scattering and scanning electron microscopy were used to analyze microparticles. Polylactide/polystyrene composite microparticles have been prepared as well; their surface morphology has been studied.