Composite polymeric electrolytes based on PMMA-LiCF3SO3-SiO2

Preliminary results on composite gel electrolytes (CGEs) with fumed silica (SiO₂) as filler added to gel polymeric electrolyte (GPE) based on PMMA, LiCF₃SO₃ and PC are presented in this paper. Added fumed silica is seen to enhance the mechanical properties of the GPE without changing the σ significantly. The high ionic conductivity (×10⁻³ S/cm), high transmission in the visible region and nominal variance of σ and ν over a wide temperature window makes these CGEs potential electrolytes for electrochromic windows (ECWs). Paper presented at the 2nd International Conference on Ionic Devices, Anna University, Chennai, India, Nov. 28–30, 2003.     

Electrical characterization of nano-composite polymer gel electrolytes containing NH4BF4 and SiO2: role of donor number of solvent and fumed silica

Nano-composite polymer gel electrolytes were synthesized by using polyethylene oxide (PEO), ammonium tetrafluoroborate (NH₄BF₄), fumed silica (SiO₂), dimethylacetamide (DMA), ethylene carbonate (EC), and propylene carbonate (PC) and characterized by conductivity studies. The effect of donor number of solvent on ionic conductivity of polymer gel electrolytes has been studied. The mechanical strength of the gel electrolytes has been increased with the addition of nano-sized fumed silica along with an enhancement in conductivity. Maximum room temperature ionic conductivity of 2.63 × 10⁻³ and 2.92 × 10⁻³ S/cm has been observed for nano-composite gel electrolytes containing 0.1 and 0.5 wt% SiO₂ in DMA+1 M NH₄BF₄+10 wt% PEO, respectively. Nano-composite polymer gel electrolytes having DMA have been found to be thermally and electrically stable over 0 to 90 °C temperature range. Also, the change in conductivity with the passage of time is very small, which may be desirable to make applicable for various smart devices.

     

Effect of nano-size fumed silica on ionic conductivity of PVdF-HFP-based plasticized nano-composite polymer electrolytes

Nano-composite polymer electrolytes containing poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP), ammonium tetrafluoroborate (NH₄BF₄), and nano-size fumed silica (SiO₂) have been prepared and characterized by complex impedance spectroscopy. Ionic conductivity of polymer has been found to increase with the addition of NH₄BF₄, and a maximum conductivity of 3.62 × 10^?6 S/cm has been obtained at 30 wt% NH₄BF₄. The formation of ion aggregates at high concentration of salt has been explained by Bjerrum’s law and mass action considerations. The conductivity of polymer electrolytes has been increased by three orders of magnitude (10^?6 to 10^?3 S/cm) with the addition of plasticizer, and a maximum conductivity of 1.10 × 10^?3 S/cm has been observed at 80 wt% DMA. An increase in conductivity with the addition of nano-size fumed silica is attributed due to the formation of space-charge layers. A maximum conductivity of 7.20 × 10^?3 S/cm has been observed for plasticized nano-composite polymer electrolytes at 3 wt% SiO₂. X-ray diffraction analysis of polymer electrolyte system was also carried out. A small change in conductivity of nano-composite polymer electrolytes observed over the 30–130 °C temperature range and for a period of 30 days is also desirable for their use in various applications.     

Preparation and performance of the polyethylene-supported polyvinylidene fluoride/cellulose acetate butyrate/nano-SiO<Subscript>2</Subscript> particles blended gel polymer electrolyte

The preparation of polyethylene-supported poly(vinylidene fluoride)/cellulose acetate butyrate/nano-SiO₂ particle (PVDF-CAB-SiO₂/PE) blended gel polymer electrolytes (GPEs) is reported here. The electrolyte uptake, mechanical properties, thermal stability, and electrochemical performance of these electrolytes are characterized to evaluate their potential application in lithium-ion batteries (LIBs). The results indicate that the particle size of SiO₂ can be adjusted by the tetraethyl orthosilicate (TEOS) concentration and affects the physicochemical properties of the membrane. By doping 5 wt.% SiO₂ (500 nm) into the PVdF-CAB blended polymer, the porosity of the membrane increases from 40 to 42.3 %, the mechanical strength from 117.3 to 138.7 MPa, the electrolyte uptake from 149 to 195 %, the oxidation decomposition potential from 4.7 to 5.2 V, and the ionic conductivity of the corresponding GPE is improved from 1.16 to 2.98 mS cm^?1 at ambient temperature. The PVDF-CAB-SiO₂/PE-based GPE and the two electrodes are suitably compatible, and the thermal stability is higher than that of the polyethylene (PE) membrane. The LIBs with the as-prepared GPE also exhibit enhanced discharge capacity and cycle stability, indicating the promising application of these GPEs in LIBs.     

Effect of nano γ-Al2O3 addition on ion dynamics in polymer electrolytes

Polymer electrolytes, which hold the key of successful operation of all solid state ionic devices, have been investigated. An amorphous polymer was used to facsimile fast ion transport in the gel polymer electrolytes (GPE) and room temperature conductivity >10⁻³ S/cm can be attained. Further, these electrolytes were transformed into composites by dispersing inorganic particles of γ-Al₂O₃ (11 nm in size) in varying wt.%. An enhancement in the conductivity for an optimum concentration using LiClO₄ as a salt can be obtained and is described in terms of free charge carrier concentration, while the other family of Lithium salts viz. LiTf, LiIm, LiBETI decreases the conductivity marginally. FTIR spectroscopy supports the observed decrease in terms of more association between fillers and salts. It has been realized that the mechanical integrity of these composites increases manifold, without affecting the conductivity, significantly.     

Conductivity studies of poly(ethylene oxide)(PEO)/poly(vinyl alcohol) (PVA) blend gel polymer electrolytes for dye-sensitized solar cells

Poly(ethylene oxide)(PEO)–poly(vinyl alcohol) (PVA) blend-based gel polymer electrolytes (GPEs) have been prepared by blending equal weights of PEO and PVA in ethylene carbonate (EC), dimethyl sulfoxide (DMSO), tetrabutylammonium iodide (TBAI), and iodine crystals (I₂). The conductivity, diffusion coefficient, number density, and ion mobility of the electrolytes have been calculated from the impedance data obtained from electrochemical impedance spectroscopy (EIS) measurements. The GPE with the composition of 7.02 wt%, PVA, 7.02 wt% PEO, 30.11 wt% ethylene carbonate (EC), 30.11 wt% DMSO, 24.08 wt% TBAI and 1.66 wt% I₂ exhibits the highest conductivity of 5.5 mS cm^?1 at room temperature. Dye-sensitized solar cells (DSSCs) with configuration fluorine tin oxide (FTO)/titanium dioxide/N3-dye/GPE/platinum/FTO have been fabricated and tested under the white light of intensity 100 mW cm^?2. The DSSC containing the highest conducting GPE exhibits the highest power conversion efficiency, η of 5.36 %.     

Role of polyvinyl alcohol in the conductivity behaviour of polyethylene glycol-based composite gel electrolytes

An attempt has been made in the present work to combine gel and composite polymer electrolyte routes together to form a composite polymeric gel electrolyte that is expected to possess high ionic conductivity with good mechanical integrity. Polyethylene glycol (PEG) based composite gel electrolytes using polyvinyl alcohol (PVA) as guest polymer have been synthesized with 1 molar solution of ammonium thiocyanate (NH₄SCN) in dimethyl sulphoxide (DMSO) and electrically characterized. The ionic conductivity measurements indicate that PEG:PVA:NH₄SCN-based composite gel electrolytes are superior (σ _max = 5.7 × 10⁻² S cm⁻¹) to pristine electrolytes (PEG:NH₄SCN system) and conductivity variation with filler concentration remains within an order of magnitude. The observed conductivity maxima have been correlated to PEG:PVA:NH₄SCN-and PVA:NH₄SCN-type complexes. Temperature dependence of conductivity profiles exhibits Arrhenius behaviour in low temperature regime followed by VTF character at higher temperature.      

Conductivity variations in composites of α-zirconium phosphate and fumed silica

Composite proton-conducting solid electrolytes have been formed from α-zirconium phosphate (α-Zr(HPO₄)₂·H₂O, α-ZrP) and high surface area non-porous fumed silica in varying mole ratios. Conductivity variations as a function of temperature and relative humidity have been characterised and compared to that for a similarly prepared delaminated ZrP (no silica). Conductivities increase with relative humidity and E_a decreases at high silica mole fractions. Conduction is via exposed lamellar surfaces and other microstructural imperfections in the composites.     

Electrochemical characterization of poly(vinylidenefluoride)-zinc triflate gel polymer electrolyte and its application in solid-state zinc batteries

Gel polymer electrolyte (GPE) films comprising of poly(vinylidenefluoride), propylene carbonate, ethylene carbonate and zinc trifluoromethane sulfonate are prepared and characterized. The composition of GPE is optimized to contain minimum liquid components with a maximum specific conductivity of 3.94×10⁻³ S cm⁻¹ at (25±1) °C. A detailed investigation on the properties such as ionic conductivity, transport number, electrochemical stability window, reversibility of Zn/Zn²⁺ couple and Zn/gel electrolyte interfacial stability have been carried out. The ionic conductivity follows a VTF behaviour with an activation energy of about 0.0014 eV. Cationic transport number varies from 0.51 at 25 °C to 0.18 at 70 °C. Several cells have been assembled with GPE as the electrolyte, zinc as the anode, γ-MnO₂ as the cathode and their charge–discharge behaviour followed. Capacity values of 105, 82, 64 and 37 mAh/g of MnO₂ have been achieved at 10, 50, 100 and 200 μA/cm² discharge current densities, respectively. The discharge capacity values are almost constant for about 55 cycles for all values of current densities. Cyclic voltammetric study of MnO₂ electrode in Zn/GPE/MnO₂ cell clearly shows intercalation/deintercalation of Zn²⁺.     

Investigation on the effects of addition of SiO<Subscript>2</Subscript> nanoparticles on ionic conductivity,FTIR, and thermal properties of nanocomposite PMMA–LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>

Composite polymer electrolyte systems composed of poly(methyl methacrylate) (PMMA) as the host polymer, lithium trifluoromethanesulphonate (also known as lithium triflate; LiCF₃SO₃) as dopant salt, and a variety of different concentrations of nano-sized fumed silica (SiO₂) as inorganic filler were studied. The effect upon addition of SiO₂ on the ionic conductivity of the composite polymer electrolytes was investigated, and it was proven that the ionic conductivity had been enhanced. In addition, the interfacial stability also showed improvement. Maximum conductivity was obtained upon addition of 2 wt.% SiO₂. The complexation of PMMA and LiCF₃SO₃ was verified through Fourier transform infrared studies. The thermal stability of the polymer electrolytes was also found to improve after dispersion of inorganic filler. This was proven in the thermogravimetric studies.     

Electrical studies on ionic liquid-based gel polymer electrolyte for its application in EDLCs

Ionic liquid-based gel polymer electrolyte (GPE) has been synthesized using standard solution cast technique. Different weight percent of ionic liquid, 1-Butyl-3-methylimidazolium chloride (BMIMCl) and liquid electrolyte, ethylene carbonate (EC)–propylene carbonate (PC)–tetra ethyl ammonium tetra fluoro borate (TEABF₄) was incorporated in polymer, poly(vinylidene fluoride-co-hexafluoro propylene (PVdF-HFP) to obtain mechanically stable gel polymer electrolyte film (GPE) having maximum conductivity of ~10⁻³ S cm⁻¹ at room temperature, which is acceptable from device fabrication point of view. Potential window and ionic transference number has been obtained to examine the potential limit and ionic characteristics of optimized GPE system. Temperature dependence behavior of electrical conductivity curve follows Arrhenius nature in the temperature range of 303–373 K. Pattern of dielectric constant and its loss as a function of frequency and temperature have been studied and is being explained on the basis of electrode interfacial polarization effect. Frequency-dependent conductivity spectra obey the Jonscher’s power law. Further, optimized composition of GPE has been tested successfully for its application in supercapacitor fabrication with activated charcoal as an electrode material. Maximum specific capacitance of 118.6 mF cm⁻² equivalent to single electrode specific capacitance of 61.7 F g⁻¹ have been observed for the optimized GPE film.

     

Conductivity, FTIR studies, and thermal behavior of PMMA-based proton conducting polymer gel electrolytes containing triflic acid

The addition of polymer to liquid electrolytes containing trifluoromethanesulfonic acid (HCF₃SO₃) in propylene carbonate (PC) has been found to result in an increase in conductivity of gel electrolytes. The increase in conductivity has been observed to be due to the dissociation of ion aggregates present in the electrolytes which has also been supported by Fourier transform infrared studies. The maximum ionic conductivity (at 25 °C) of 7.55?×?10^?3 S/cm has been observed for polymer gel electrolytes containing 1.5 wt% polymethylmethacrylate in 0.5 M solution of HCF₃SO₃ in PC. Polymer gel electrolytes have been found to be thermally stable up to a temperature of 125 °C by simultaneous differential scanning calorimetry/thermogravimetric analysis studies. The conductivity of polymer gel electrolytes does not show any appreciable change over a limited period of time.     

Electrochemical characterization of ionic liquid based gel polymer electrolyte for lithium battery application

High molecular weight polymer poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP), ionic liquid 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide (EMIMFSI), and salt lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-based free-standing and conducting ionic liquid-based gel polymer electrolytes (ILGPE) have been prepared by solution cast method. Thermal, electrical, and electrochemical properties of 80 wt% IL containing gel polymer electrolyte (GPE) are investigated by thermogravimetric (TGA), impedance spectroscopy, linear sweep voltammetry (LSV), and cyclic voltammetry (CV). The 80 wt% IL containing GPE shows good thermal stability (~?200 °C), ionic conductivity (6.42?×?10^?4 S cm^?1), lithium ion conductivity (1.40?×?10^?4 S cm^?1 at 30 °C), and wide electrochemical stability window (~?4.10 V versus Li/Li⁺ at 30 °C). Furthermore, the surface of LiFePO₄ cathode material was modified by graphene oxide, with smooth and uniform coating layer, as confirmed by scanning electron microscopy (SEM), and with element content, as confirmed by energy dispersive X-ray (EDX) spectrum. The graphene oxide-coated LiFePO₄ cathode shows improved electrochemical performance with a good charge-discharge capacity and cyclic stability up to 50 cycles at 1C rate, as compared with the without coated LiFePO₄. At 30 °C, the discharge capacity reaches a maximum value of 104.50 and 95.0 mAh g^?1 for graphene oxide-coated LiFePO₄ and without coated LiFePO₄ at 1C rate respectively. These results indicated improved electrochemical performance of pristine LiFePO₄ cathode after coating with graphene oxide.     

Polyethylene-supported poly(methyl methacrylate<Emphasis Type="Italic">-co-</Emphasis>butyl acrylate)-based novel gel polymer electrolyte for lithium ion battery

A new copolymer, poly(methyl methacrylate-co-butyl acrylate) (P(MMA-co-BA)), was synthesized by emulsion polymerization with different mass ratio of methyl methacrylate (MMA) and butyl acrylate (BA). The membranes were prepared by phase inversion and corresponding gel polymer electrolytes (GPEs) were obtained by immersing the membrane into a liquid electrolyte. In this design, the hard monomer MMA provided the copolymer with good electrolyte uptake, while the soft monomer BA provided the GPE with strong adhesion between the anode and cathode of lithium ion battery. The properties of the resulting product were investigated by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectra, scanning electron spectroscopy, linear sweep voltammetry, thermogravimetric analysis, cyclic voltammetry, electrochemical impedance spectroscopy and charge/discharge test. The results show that the obtained GPE based on P(MMA-co-BA) with the mass ratios of MMA and BA = 6:1 exhibits good conductivity (as high as 1.2 × 10^?3 S cm^?1) at room temperature and high electrochemical stability (up to 4.9 V vs. Li/Li⁺). With the application of the polyethylene (PE)-supported GPE in Li/Li(Li_0.13Ni_0.30Mn_0.57)O₂ battery, the battery presents good cyclic stability (maintaining 95.4 % of its initial discharge capacity after 50 cycles) at room temperature.     

Preparation and properties of a gel polymer electrolyte system based on poly-ε-caprolactone containing 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide

Gel polymer electrolytes (GPE) obtained by immobilizing a solution of zinc triflate (ZnTr) in an ionic liquid, namely 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [emim][Tf₂N] within a biodegradable polymeric matrix of poly-ε-caprolactone (PCL) were prepared by a simple solvent cast technique for different concentrations of the ionic liquid. The electrolyte with the composition 75 wt% PCL: 25 wt% ZnTr+100 wt% [emim][Tf₂N] showed the highest ionic conductivity of 1.1×10⁻⁴ S cm⁻¹ at 25 °C and favored by the rich amorphous phase of the GPE as confirmed from room temperature X-ray diffraction analysis (XRD). The morphology of the GPE was examined using scanning electron microscopy (SEM) which revealed the homogeneity of the prepared GPE system. The temperature dependence of electrical conductivity of the GPE followed the Arrhenius behavior. The Zn²⁺ ionic transport number has been determined to be ~0.62 which denotes the predominant contribution of zinc ion towards total ionic conductivity. The electrochemical stability window of GPE is found to be 2.5 V with a thermal stability upto 200 °C. This eco-friendly and safe electrolyte may be used to fabricate compostable batteries, in future, with a suitable selection of other components of the battery system.     

Properties of a gel polymer electrolyte based on lithium salt with poly(vinyl butyral)

Poly(vinyl butyral) (PVB) is of particular interest because of its low cost, extremely wide temperature work range (? 20 to 120 °C), and efficient chemical stability. In this study, a gel polymer electrolyte (GPE) containing Li⁺ ions was fabricated by using dimethylacetylamine (DMA), lithium perchlorate (LiClO₄), and PVB. The experimental results indicated that a highly transparent GPE with a high ionic conductivity (σ) could be obtained by mixing glue (DMA with a PVB content of 10 wt%) with a LiClO₄ content of 6 wt%. It was found that the ionic conductivity (σ) of the GPE depended on the LiClO₄ content, and the GPE with a LiClO₄ content of 6 wt% exhibited a maximum σ of 7.73 mS cm^?1, a viscosity coefficient of 3360 mPa s, and a transmittance greater than 89% (visible region) at room temperature. Furthermore, PVB improved the electrolyte solution leakage, and the LiClO₄ was used as an ion supply source for the high σ of the GPE.     

Performance evaluation of PVdF gel polymer electrolytes

A series of gel polymer electrolytes containing PVdF as homo polymer, a mixture of 1:1 Ethylene Carbonate (EC) : Propylene Carbonate (PC) as plasticizer and lithium-bistrifluoromethane sulphone imide [imide — LiN (CF₃SO₂)₂] has been developed. Amounts of polymer (PVdF), plasticizer and the imide lithium salt have been varied as a function of their weight ratio composition in this regard. Dimensionally stable films possessing appreciable room temperature conductivity values have been obtained with respect to certain weight ratio compositions. However, conductivity data have been recorded at different possible temperatures, i.e., from 20 °C to 65 °C. XRD and DSC studies were carried out to characterize the polymer films for better amorphicity and reduced glass transition temperature, respectively. The electrochemical interface stability of the PVdF based gel polymer electrolytes over a range of storage period (24 h – 10 days) have been investigated using A.C. impedance studies. Test cells containing Li/gel polymer electrolyte (GPE)/Li have been subjected to undergo 50 charge-discharge cycles in order to understand the electrochemical performance behaviour of the dimensionally stable films of superior conductivity. The observed capacity fade of less than 20% even after 50 cycles is in favour of the electrochemical stability of the gel polymer electrolyte containing 27.5% PVdF −67.5 % EC+PC −5% imide salt. Cyclic voltammetry studies establish the possibility of a reversible intercalation — deintercalation process involving Li⁺ ions through the gel polymer electrolyte.     

Effect of molecular weight of PMMA on the conductivity and viscosity behavior of polymer gel electrolytes containing NH<Subscript>4</Subscript>CF<Subscript>3</Subscript>SO<Subscript>3</Subscript>

The addition of polymethyl methacrylate (PMMA) having different molecular weights to electrolytes containing ammonium trifluoromethanesulfonate (NH₄CF₃SO₃) in diethyl carbonate (DEC) has been found to result in conductivity enhancement and to yield gel electrolytes with conductivity higher than the corresponding liquid electrolytes. The increase in conductivity has been found to be due to the dissociation of undissociated NH₄CF₃SO₃ and ion aggregates present in the electrolytes, and this has been supported by Fourier transform infrared spectroscopy results, which suggests active interaction of PMMA and NH₄CF₃SO₃ in these gel electrolytes. The increase in conductivity also depends upon the molecular weight of the polymer used and is relatively more for PMMA having lower molecular weight. The increase in viscosity with PMMA addition also depends upon the molecular weight of the polymer and is closely related to the conductivity behavior of these electrolytes. Polymer gel electrolytes have been found to be thermally stable up to a temperature of 125 °C.     

The effect of LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript> on the complexation with potato starch-chitosan blend polymer electrolytes

This work examines the effect of lithium trifluoromethanesulfonate (LiCF₃SO₃) and glycerol on the conductivity and dielectric properties of potato starch-chitosan blend-based electrolytes. The electrolytes are prepared via solution cast technique. From X-ray diffraction (XRD) analysis, the blend of 50 wt.% starch and 50 wt.% chitosan is found to be the most amorphous blend. Fourier transform infrared (FTIR) spectroscopy studies show the interaction between the electrolyte materials. The room temperature conductivity of pure starch-chitosan film is found to be (2.85 ± 1.31) × 10^?10 S cm^?1. The incorporation of 45 wt.% LiCF₃SO₃ increases the conductivity to (7.65 ± 2.27) × 10^?5 S cm^?1. Further conductivity enhancement up to (1.32 ± 0.35) × 10^?3 S cm^?1 has been observed on addition of 30 wt.% glycerol. This trend in conductivity is verified by XRD and dielectric analysis. The temperature dependence of conductivity of all electrolytes are Arrhenian.     

Influence of surface treatment on mechanical behaviour of fumed silica/epoxy resin nanocomposites

The present paper shows the potential of fumed silica as nano-reinforcements in polymers, by considering the limitations and challenges one has to face dealing with nanoparticles in general. The dominating effect of the manufacturing route and surface properties of fumed silica influencing the resulting degree of dispersion and the interfacial adhesion were investigated by electron microscopy (TEM, SEM). The resulting (fracture-) mechanical properties of the fumed silica/epoxy composites were investigated for volume contents of 0.5 vol% and below. Independent of the surface modification, static and dynamic modulus decreased slightly by adding the fumed silica. Hence, the fracture toughness K _Ic turned out to be significantly increased (54%) adding only 0.5 vol% of surface modified fumed silica.