Kinetic spectrofluorimetric determination of trace ascorbic acid based on its inhibition on the oxidation of pyronine Y by nitrite

A highly sensitive spectrofluorimetric method is proposed for the determination of trace amount of ascorbic acid using a new indication. The method is based on the inhibition of ascorbic acid on the oxidation of pyronine Y (PRY) by nitrite. The detection limit for ascorbic acid is 0.012 microg ml(-1), the linear range of the determination is 0.02-0.36 microg ml(-1). Analytical parameters, such as reagent concentration, pH, reaction temperature and time, were optimized. The relative standard deviations of eleven replication determinations of 0.12 and 0.24 microg ml(-1) ascorbic acid were 1.4 and 0.72%, respectively. This method has been used to determine ascorbic acid in pharmaceuticals, vegetables, fruits and soft drink with satisfactory results.     

Kinetic determination of cysteine on flow injection system by utilizing catalytic complexation reaction of Cu(II) with 5,10,15,20-tetrakis (4-N-trimethylammino-phenyl) porphyrin

A kinetic method for the determination of cysteine on flow injection system is described. Cysteine was found as a catalyst for the complexation reaction of Cu(II) with an ultra sensitive colorimetric reagent of 5,10,15,20-tetrakis (4-N-trimethylammino-phenyl) porphyrin (TTMAPP) (varepsilon=4.8x10(5)cm(-1)M(-1) at 433nm), which was used as the indicator reaction in this paper. Soret band of either the porphyrin or the produced complex (varepsilon=4.6x10(5)cm(-1)M(-1) at 411nm) can be used for detection. The continuous flow injection system greatly enhanced the analytic precision and efficiency of the kinetic method, giving a relative standard deviation of 0.73% for a 0.1mugml(-1) cysteine with 10 injections at a throughput of 30h(-1). The detection limits (3S/N) in this case was 15ngml(-1) and the working dynamic range was over 25ngml(-1) to 1mugml(-1). Sugars, organic acids and amino acids that are possible in coexistence with cysteine could be tolerated at high concentrations. This method was critically compared with the Ellman's reagent in the determinations of cysteine contents of three pharmaceutical injections for hepatic diseases and one permanent wave agent and showed better applicability in the respect of matrix interferences.     

Flow injection chemiluminescence analysis of some penicillins by their sensitizing effect on the potassium permanganate-glyoxal reaction.

A new chemiluminescence method using flow injection is described for the determination of four penicillins, namely: phenoxymethylpenicillin potassium, amoxicillin, ampicillin, and ampicillin sodium. The method is based on sensitizing effect of these drugs on the chemiluminescence reaction of potassium permanganate in sulfuric acid with glyoxal. The different experimental parameters affecting the chemiluminescence intensity were carefully studied and incorporated into the procedure. The method allows the determination of 0.1-1.0 microg/ml phenoxymethylpenicillin potassium, 0.1-1.0 microg/ml amoxicillin, 0.1-1.0 microg/ml ampicillin, and 0.1-1.0 microg/ml ampicillin sodium. The method was successfully applied to the determination of four penicillin antibiotics in pharmaceutical preparations.     

Determination of ascorbic acid in soft drinks, preserved fruit juices and pharmaceuticals by flow injection spectrophotometry: Matrix absorbance correction by treatment with sodium hydroxide

Two flow injection systems for the spectrophotometric determination of ascorbic acid at 245 nm have been described. On treatment with sodium hydroxide a fraction of the ascorbic acid was decomposed into substances, which do not absorb in UV region, and the decrease in signal measured. This was directly related to the amount of ascorbic acid present. The calibration graph was linear over the range 1-25 and 1-50 microg/ml in the two methods with a correlation coefficient of 0.9981 and 0.9994, respectively. The detection limit (2sigma) was 0.5 and 0.2 microg/ml, respectively. The RSD for 1 microg/ml standard was 2.5 and 1.8% (n = 6) in the two methods, and the sampling throughput 30/hr. The methods permitted the use of 6 microg/ml of 2-mercaptoethanol as an anti-oxidant and stabilizer for ascorbic acid, which is difficult to handle at its microg/ml level. Upon matrix absorbance correction, spiked samples that are known to contain UV-absorbing substances produced an average recovery of 101% with a RSD of 1.2%. The methods were used for the rapid and simple determination of ascorbic acid in soft drinks, preserved fruit juices and pharmaceuticals and the results thus produced compared with those obtained by previously checked methods involving titration with iodine, chloranil 2,6-dichlorophenolindophenol, and HPLC. When there was a disagreement between the results, this was traced to the presence of substances which are known to interfere in comparison methods.     

Kinetic spectrophotometric determination of ascorbic acid by reduction of toluidine blue

A simple kinetic method is described for the determination of ascorbic acid. The procedure is based on the reduction of toluidine blue with ascorbic acid. The rate of reaction is followed by measuring the decrease in absorbance of toluidine blue (lambda(max) = 600 nm) as a result of its decolorization upon reduction by ascorbic acid. Ascorbic acid in the range of 3-35 microg/ml was determined using slope and fixed time methods of analysis, while the variable time method allowed the determination of 5-50 microg/ml of ascorbic acid. The percent relative standard deviation of the method varied from 0.78 to 1.32% depending on the kinetic method used. The high sensitivity of the method also allows determination of low levels of ascorbic acid in some fruits and vegetables such as dew melon, water melon, parsley and coriander.     

Fluorimetric determination of total ascorbic acid by a stopped-flow mixing technique

A simple, rapid and automatic fluorimetric method for the determination of total ascorbic acid is described. The method makes use of the stopped-flow mixing technique in order to achieve the rapid oxidation of ascorbic acid by dissolved oxygen to dehydroascorbic acid, which then reacts with o-phenylenediamine to form a fluorescent quinoxaline. The initial rate and fluorescence signal of this system are directly proportional to the ascorbic acid concentration. The calibration graph was linear over the range 0.1-30 microg ml(-1) (kinetic method) and 0.25-34 microg ml(-1) (equilibrium method). The precision (% RSD) was close to 0.5%. The method has been used for the determination of ascorbic acid in pharmaceutical formulations, fruit juices, soft drinks and blood serum.     

Spectrophotometric determination of ascorbic acid in pharmaceuticals by background correction and flow injection

Background correction has been shown to be an effective and indispensable modification in the spectrophotometric determination of ascorbic acid. The decomposition of ascorbic acid in pharmaceutical samples was carried out by incubation with sodium hydroxide to give products that were insensitive to ultraviolet light. The rapid oxidation in air of ascorbic acid, especially in dilute solutions, was avoided by the use of the flow injection principle for spectrophotometric determination and by employing a carrier stream of an anti-oxidizing nature consisting of 6 micrograms ml(-1) of 2-mercaptoethanol in 0.25% sulphuric acid. The optimized method with a single channel manifold made use of a carrier stream flow rate of 1.1 ml min(-1), an injection volume of 50 microl, a delay coil of 50 cm (0.5 mm i.d.) and detection at 245 nm. The throughput was at least 180 injections h(-1). The proposed flow injection method yielded results for the analysis of 0-20 micrograms ml(-1) of ascorbic acid that were 99-102% (relative standard deviation 0.6% or better) in agreement with those produced by comparable methods involving titration with iodine, chloranil or 2,6-dichlorophenolindophenol [4-(2,6-dichloro-4-hydroxyphenylimino)cyclohexa-2,5-dieno ne], and high-performance liquid chromatography. When the agreement was not good (as low as 14% with respect to the method being compared), this was traced to the presence of substances which are known to interfere in one or other of the methods of comparison.     

Spectrophotometric determination of iron with ferrozine by flow-injection analysis

Two methods for the determination of iron by normal FIA and reversed FIA were developed using sodium 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine-4',4'-disulphonate (ferrozine). The reagent formed a chelate with Fe(II) in hexamethylentetramine buffered medium at pH 5.5. In one previous reaction coil Fe(III) was reduced to Fe(II) by ascorbic acid and in the other reaction coil the complexation reaction was developed. The linear range of the determination was 0.5-6 and 0.1-5 mug ml(-1) of iron for normal FIA and reversed FIA respectively. The proposed method was sensitive (detection limit 0.012 and 0.010 mug ml(-1)), rapid and reproducible (RSD 0.3 and 0.28%). The method was satisfactorily applied to the determination of iron in waste water, toadstool tissue, potato leaves, human hair and bauxites at a sampling rate of 90 and 50 samples h(-1) for normal FIA and reversed FIA respectively.     

Indirect spectrophotometric determination of ascorbic acid with ferrozine by flow-injection analysis

A FIA indirect spectrophotometric determination of ascorbic acid was developed using its reducing action on Fe(III) in acidic medium and following the spectrophotometric determination of the reduced iron by using sodium 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine-4',4'-disulphonate (ferrozine) as chromogenic reagent in buffered medium (pH 5.5) and monitoring the absorbance signal at 562 nm. A three-line manifold with two reaction coils was used: in the first reaction coil, ascorbic acid reduces Fe(III) to Fe(II); and in the second one, the complexation reaction is developed. The linear range of the method was 0.5-10 mug ml(-1) of ascorbic acid, the detection limit being 0.028 mug ml(-1). The proposed method was sensitive, rapid (sampling rate of 90 samples h(-1)) and reproducible (RSD 0.19%, n=10). Satisfactory results were obtained in the determination of ascorbic acid in pharmaceutical preparations, fruit juices and urine testifying the applicability of the method to real samples.     

Chemiluminescence flow sensor for the determination of ascorbic acid with immobilized reagents

A novel flow sensor based on chemiluminescence (CL) for the determination of ascorbic acid has been proposed. The analytical reagents, luminol and ferricyanide, were both immobilized on an anion-exchange resin column. The CL signal produced by the reaction between luminol and ferricyanide, which were eluted from the column through sodium phosphate injection, was decreased in the presence of ascorbic acid. The CL emission intensity was linear with ascorbic acid concentration in the range 0.01-0.8 mug ml(-1); the detection limit was 5.5 x 10(-3) mug ml(-1). The whole process, including sampling and washing, could be completed in 1 min with a relative standard deviation of less than 5%. The sensor could be reused more than 100 times and has been applied successfully to the analysis of ascorbic acid in pills and vegetables.     

Atomic absorption spectrometry for the automatic indirect determination of ascorbic acid based on-the reduction of manganese dioxide.

A new and simple flow injection method followed by atomic absorption spectrometry has been developed for the indirect determination of ascorbic acid. The proposed method is based on oxidation of ascorbic acid to dehydroascorbic acid using a solid-phase manganese dioxide (30% m/m suspended on silica gel beads) reactor. The flow of the sample through the column reduces the MnO2 to Mn(II) in an acidic carrier stream of 6.3 mM HNO3 (pH 2.2) with flow rate of 4.0 ml/min at room temperature; Mn(II) is measured by atomic absorption spectrometry. The absorbance of Mn(II) is proportional to the concentration of ascorbic acid in the sample. The calibration curve was linear up to 30 mg/L, with a detection limit of 0.2 mg/L for a 220 microL injected sample volume. The developed procedure was found to be suitable for the determination of AsA in pharmaceuticals and foods with a relative standard deviation better than 1.09% and a sampling rate of about 95 h(-1). The results exhibit no interference from the presence of large amounts of organic compounds. The reliability of the method was established by parallel determination against the 2,6-dichlorophenol-indophenol methods.     

Flow injection spectrophotometric determination of ascorbic acid in soft drinks and beer

Two spectrophotometric methods, a photochemical and a non-photochemical, for the determination of ascorbic acid in soft drinks and beer using a flow-injection system are proposed. The non-photochemical method is based on the redox reaction that takes place between ascorbic acid and Fe(III), yielding dehydroascorbic acid and Fe(II). Fe(II) reacts with 1,10-phenantroline, originating the reddish orange Fe(phen)3(2+) complex (ferroin). This complex is spectrophotometrically monitored at 512 nm, and the signal is directly related to the concentration of ascorbic acid in the sample. The photochemical method has the same basis, nevertheless, uses the irradiation with visible light to enhance the redox reaction and so achieve higher sensitivities in the analysis. The non-photochemical method shows a linear range between 5 and 80 microg mL(-1), with a relative standard deviation of 1.6% (n = 11), a detection limit of 2.7 microg mL(-1) and a sample throughput of 60 samples h(-1). The photochemical method shows a linear range between 1 and 80 microg mL(-1), with a relative standard deviation of 1.0% (n = 11 ), a detection limit of 0.5 microg mL(-1) and a sample throughput of 40 samples h(-1).     

Kinetic spectrophotometric method for the determination of oxalic acid by its catalytic effect on the oxidation of safranine by dichromate

A new catalytic kinetic spectrophotometric method for the determination of oxalic acid has been described based on its catalytic effect on the redox reaction between safranine and dichromate in dilute sulfuric acid media. The reaction is monitored photometrically by measuring the decrease in absorbance of safranine at the maximum wavelength of 530 nm. Under the optimum conditions, a calibration graph from 0.10 to 10.00 microg ml(-1) of oxalic acid with a detection limit of 0.08 microg ml(-1) was obtained. The relative standard deviation (R.S.D.) for ten replicate measurements of 1.0 and 5.0 microg ml(-1) oxalic acid was 2.7 and 2.5%, respectively. The purposed method is simple, sensitive, selective and inexpensive. The applicability of the proposed method was determined by the determination of oxalic acid in spinach and wastewater samples with satisfactory results.     

Spectrophotometric determination of a nanomolar amount of ascorbic acid using its catalytic effect on copper(II) porphyrin formation

A simple, fast and sensitive flow-injection method is proposed for the determination of nanomolar amounts of ascorbic acid in tea, urine and blood. The procedure is based on the accelerating effect of a nanomolar level of ascorbic acid on the reaction of cooper(II) with 5,10,15,20-tetrakis(1-methylpyridinium-4-yl)porphyrin, H(2)tmpyp(4+). Ascorbic acid reduces Cu(II) to Cu(I) which catalyzes the incorporation of Cu(II) into H(2)tmpyp(4+) to form Cu(II)(tmpyp)(4+). In this method two solutions, one containing ascorbic acid and H(2)tmpyp(4+) and the other containing copper(II) and acetate buffer (pH 5.0), were injected into two flowing streams of water through two sample injectors of 120 mu1 sample volume. The mixture was allowed to react in a 2 m reaction coil and the colored solution of Cu(II)(tmpyp)(4+) was monitored at 550 nm (epsilon = 2.01 x 10(4)M(-1)cm(-1)). The present method was applied to the determination of ascorbic acid in tea, urea and blood. Reducing agents such as sugars and vitamins B(1), B(2), B(6) and B(12) did not give serious errors at a concentration of 10(-6) M for the determination of 1.0 x 10(-8)M ascrobic acid. The relative standard deviation of the present method was 2.8% for the determination of 1.0 x 10(-8)M ascorbic acid. The reaction mechanism was clarified from the kinetic results of the formation of Cu(II)(tmpyp)(4+) in the presence of various concentrations of ascorbic acid, copper(II) and hydrogen ion.     

Spectrofluorimetric flow injection determination of trace amounts of periodate

A sensitive, rapid and selective procedure is proposed for the flow injection determinations of periodate by spectrofluorometric detection. The method is based on the reaction of periodate with Alizarin Navy Blue in basic solution. The reagents and manifold variables influence on the sensitivity have been investigated and the optimum conditions are established. Periodate can be determined for the range of 0.250-5.00 microg ml(-1) with a limit of detection of 0.08 microg ml(-1), and with a sample rate of 15 +/- 2 samples h(-1). The relative standard deviations for eight replicate determination of 0.500 and 5.00 microg ml(-1) was 1.3 and 1.1%, respectively. Periodate can be determined in the presence of iodate and bromate. The proposed method was used to determination of periodate in water samples.     

Flow injection amperometric detection of ascorbic acid using a Prussian Blue film-modified electrode

The PB film-modified electrode was used as an amperometric detector for flow injection analysis of ascorbic acid. The modified electrode detector showed good sensitivity, stability and reproducibility. The calibration curve for ascorbic acid was linear over the concentration range from 5.0x10(-6) to 1.0x10(-3) mol l(-1) with a slope of 19.9 mA mol(-1) per litre and a correlation coefficient of 0.999. The detection limit of this method was 2.49x10(-6) mol l(-1). The relative standard deviation of six replicate injections of 2.5x10(-4) mol l(-1) ascorbic acid was 2.5%. The results obtained for ascorbic acid determination in pharmaceutical products are in good agreement with those obtained by using the procedure involving the reaction between triiodide and ascorbic acid.     

Determination of 0.1 to 1000 μ g/ml cadmium in a hydrometallurgical zinc refining process stream by a flow injection technique with computer controlled injection method

A computer-controlled flow injection system was developed for the determination of cadmium in a hydrometallurgical zinc refining process stream. An anion-exchange method in acidic potassium iodide medium was used for the on-line separation of cadmium from the matrix zinc. 1-(4-Nitrophenyl)-3-(4-phenylazophenyl)triazene (Cadion) was used as the chromogenic reagent for the spectrophotometric detection of cadmium. In order to expand the dynamic range of the flow injection - spectrophotometry, a computer-aided time-based variable-volume injection method has been employed for the introduction of the sample into the flow injection system. Samples ranging from 0.56 to 350 microl can be delivered by controlling the time period of the sample introduction valve and the flow rate of the carrier solution. The system permits a throughput of 5 samples per hour. The reproducibility has been proven to be satisfactory with a relative standard deviation of less than 6.2% (sample injected: 0.56 microl of 850 microg Cd/ml; n=100) and 5.0% (350 microl of 0.14 microg Cd/ml; n=5). The determination limit was 20 microg Cd/ml with 0.56 microl sample injection and 0.05 microg Cd/ml with 350 microl sample injection (the absolute amount of cadmium injected into the system was 11 ng and 17.5 ng, respectively).     

Permanganate-based chemiluminescence analysis of cefadroxil monohydrate in pharmaceutical samples and biological fluids using flow injection

A chemiluminescent method using flow injection is described for the determination of cefadroxil monohydrate. The method is based on the chemiluminescence reaction of cefadroxil with potassium permanganate in sulphuric acid, sensitized by quinine. The proposed procedure allows the determination of cefadroxil over the concentration range 0.1-30 mug ml(-1) with a detection limit of 0.05 mug ml(-1) and a sample measurement frequency of 150 samples h(-1). The method was successfully applied to the determination of cefadroxil in pharmaceutical preparations and biological fluids.     

Flow injection determination of formaldehyde by its catalytic effect on the oxidation of sulfonazo III by bromate with spectrophotometric detection.

A simple and sensitive flow injection method with spectrophotometric detection was developed for the determination of formaldehyde. The method is based on the catalytic effect of formaldehyde on the oxidation of sulfonazo III with bromate in acidic media. The decrease in absorbance of the reaction mixture was measured at 566 nm. The calibration graph was linear in the range of 0.005 to 2.80 microg ml(-1) formaldehyde at a rate of 38 +/- 4 samples h(-1). The limit of detection was 4 ng ml(-1). The relative standard deviations for ten replicate measurements of 0.20, 0.50 and 1.00 microg ml(-1) formaldehyde were 1.3, 0.8 and 0.7%, respectively. The method was applied to the determination of formaldehyde in river water, shampoo and melamine-formaldehyde resin.     

Flow injection kinetic spectrophotometric determination of ascorbic acid based on an inhibiting effect

A rapid and sensitive flow-injection kinetic spectrophotometric method is proposed for the determination of ascorbic acid. The procedure is based on the inhibiting effect of ascorbic acid on the enhancing effect of oxalate on the potassium dichromate-potassium iodide/rhodamine 6G system. The detection limit and linear ranges are 0.08 and 0.10-4.00 microg/ml, respectively. The relative standard deviation of 11 replicate measurements is less than 2.0%. This method has been successfully used to determine ascorbic acid in pharmaceuticals, tomatoes and oranges.