MOF Encapsulated AuPt Bimetallic Nanoparticles for Improved Plasmonic-induced Photothermal Catalysis of CO2 Hydrogenation

Exploring new catalytic strategies for achieving efficient CO₂ hydrogenation under mild conditions is of great significance for environmental remediation. Herein, a composite photocatalyst Zr-based MOF encapsulated plasmonic AuPt alloy nanoparticles (AuPt@UiO-66-NH₂) was successfully constructed for the efficient photothermal catalysis of CO₂ hydrogenation. Under light irradiation at 150 °C, AuPt@UiO-66-NH₂ achieved a CO production rate of 1451 μmol g_metal⁻¹ h⁻¹ with 91 % selectivity, which far exceeded those obtained by Au@Pt@UiO-66-NH₂ with Pt shell on Au (599 μmol g_metal⁻¹ h⁻¹) and Au@UiO-66-NH₂ (218 μmol g_metal⁻¹ h⁻¹). The outstanding performances of AuPt@UiO-66-NH₂ were attributed to the synergetic effect originating from the plasmonic metal Au, doped active metal Pt, and encapsulation structure of UiO-66-NH₂ shell. This work provides a new way for photothermal catalysis of CO₂ and a reference for the design of high-performance plasmonic catalysts.     

Carbon black supported PtCu nanoparticles derived from mix-phased Cu precursor for high-performanced oxygen reduction reaction in acid medium

Alloying high-cost Pt with transition metals has been considered as an effective route to synthesize the electrocatalysts with low Pt loading and excellent activity towards oxygen reduction reaction (ORR) under acid solution. The galvanic replacement method, as featured with efficiency and simplicity, is widely reported to produce Pt-based bimetallic alloys and thereby declare the significance of reductive transition metal precursor on the enhancement of ORR performance. Herein, mix-phased Cu−Cu₂O precursor was applied to prepare carbon black supported highly dispersed PtCu alloy nanoparticles (PtCu/C). The proper Cu−Cu₂O ratios can exactly facilitate the generation of small sized PtCu alloy nanoparticles with regulated bimetallic content. Meanwhile, the Cu₂O phase is revealed to benefit the electron transfer from Pt to Cu and thus improve the intrinsic activity of Pt active sites. And the metallic Cu can favor the promotion of electrochemical active surface area. Consequently, the as-prepared PtCu/C behaves impressive ORR activity with half-wave potential of 0.88 V (vs. RHE) and mass activity of 0.49 A cm⁻² mg_Pt⁻¹ at 0.8 V, which is 9.8 times of commercial Pt/C catalysts. Our work will offer helpful advices for the development and regulation of novel Pt-based alloy materials towards diverse electrocatalysis.     

Improving the Electrocatalytic Activity of a Nickel-Organic Framework toward the Oxygen Evolution Reaction through Vanadium Doping

Metal-organic frameworks (MOFs) have been considered as potential oxygen evolution reaction (OER) electrocatalysts owning to their ultra-thin structure, adjustable composition, high surface area, and high porosity. Here, we designed and fabricated a vanadium-doped nickel organic framework (V_1−x−Ni_xMOF) system by using a facile two-step solvothermal method on nickel foam (NF). The doping of vanadium remarkably elevates the OER activity of V_1−x−Ni_xMOF, thus demonstrating better performance than the corresponding single metallic Ni-MOF, NiV-MOF and RuO₂ catalysts at high current density (>400 mA cm⁻²). V_0.09−Ni_0.91MOF/NF provides a low overpotential of 235 mV and a small Tafel slope of 30.3 mV dec⁻¹ at a current density of 10 mA cm⁻². More importantly, a water-splitting device assembled with Pt/C/NF and V_0.09−Ni_0.91MOF/NF as cathode and anode yielded a cell voltage of 1.96 V@1000 mA cm⁻², thereby outperforming the-state-of-the-art RuO₂⁽⁺⁾||Pt/C⁽⁻⁾. Our work sheds new insight on preparing stable, efficient OER electrocatalysts and a promising method for designing various MOF-based materials.     

In Situ Growth of Ultrafine Pt Nanoparticles onto Hierarchical Co3O4 Nanosheet-Assembled Microflowers for Efficient Electrocatalytic Hydrogen Evolution

The development of Pt-based electrocatalysts with high Pt utilization efficiency toward the hydrogen evolution reaction (HER) is of great significance for the future sustainable hydrogen economy. For rational design of high-performance HER electrocatalyst, the simultaneous consideration of both thermodynamic and kinetic aspects remains greatly challenging. Herein, a simple template-derived strategy is demonstrated for the in situ growth of ultrafine Pt nanoparticles onto Co₃O₄ nanosheet-assembled microflowers (abbreviated as Pt/Co₃O₄ microflowers hereafter) by using the pre-fabricated PtCo-based Hofmann coordination polymer as reactive templates. The elaborate preparation of such intriguing hierarchical architecture with well-dispersed tiny Pt nanoparticles, abundant metal/oxide heterointerfaces and open configuration endows the formed Pt/Co₃O₄ microflowers with high Pt utilization efficiency, rich active sites, lowered energy barrier for water dissociation and expedited reaction kinetics. Consequently, the Pt/Co₃O₄ microflowers exhibit superior HER activity with a relatively low overpotential of 34 mV to deliver a current density of 10 mA cm⁻², small Tafel slope (34 mV dec⁻¹) and outstanding electrochemical stability, representing an attractive electrocatalyst for practical water splitting. What's more, our concept of in situ construction of metal/oxide heterointerfaces may provide a new opportunity to design high-performance electrocatalysts for a variety of applications.     

Extending Surface-Enhanced Raman Spectroscopy to Liquids Using Shell-Isolated Plasmonic Superstructures

Plasmonic superstructures (PS) based on Au/SiO₂ were prepared for Shell-Isolated Nanoparticle-Enhanced Raman Spectroscopy (SHINERS) in liquid phase applications. These superstructures are composed of functionalized SiO₂ spheres with plasmonic Au nanoparticles (NPs) on their surface. Functionalization was performed with (3-aminopropyl)trimethoxysilane, (3-mercaptopropyl)trimethoxysilane and poly(ethylene-imine) (PEI). Of these three, PEI-functionalized spheres showed the highest adsorption density of Au NPs in TEM, UV/Vis and dynamic light scattering (DLS) experiments. Upon decreasing the Au NP/SiO₂ sphere size ratio, an increase in adsorption density was also observed. To optimize plasmonic activity, 61 nm Au NPs were adsorbed onto 900 nm SiO₂-PEI spheres and these PS were coated with an ultrathin layer (1–2 nm) of SiO₂ to obtain Shell-Isolated Plasmonic Superstructures (SHIPS), preventing direct contact between Au NPs and the liquid medium. Zeta potential measurements, TEM and SHINERS showed that SiO₂ coating was successful. The detection limit for SHINERS using SHIPS and a 638 nm laser was around 10⁻¹² m of Rhodamine (10⁻¹⁵ m for uncoated PS), all with acquisition settings suitable for catalysis applications.     

Activated Single-Phase Ti4O7 Nanosheets with Efficient Use of Precious Metal for Inspired Oxygen Reduction Reaction

The oxygen reduction reaction (ORR) is central to modern energy storage and conversion technologies for grids such as fuel cells and electrolyzers, but challenges remain due to the lack of reliable, economic, and durable electrocatalysts. Here, we develop single-crystal conductive black titanium (Ti₄O₇) nanosheets (NSs) as a new precious metal carrier based on sacrificial hard templates and ultrasonic-assisted peeling, and deposit Pt clusters on Ti₄O₇ NSs induced by wetness impregnation under the irradiation of visible light (VI; 650 nm). Pt/Ti₄O₇ NSs provide Ti³⁺, Pt²⁺, and Pt⁰⁺ continuous active sites for the ORR multielectron process, achieving synergy among them. The assistance of visible light not only makes a more uniform and smaller distribution of Pt nanoclusters, but also strengthens the charge transfer, thereby constructing a strong metal-support interaction interface. VI−Pt/Ti₄O₇ NSs show superior initial oxidation potential and a mass activity of 1.61 A mg⁻¹_Pt at a E_1/2=0.91 V, which is nine times higher than that of commercial Pt/C. This work provides an effective strategy for achieving high-value applications of titanium sub-oxides and further explores the enhanced interface in metals Ti_nO_2n-1 by light radiation.     

MnO/N-Doped Mesoporous Carbon as Advanced Oxygen Reduction Reaction Electrocatalyst for Zinc–Air Batteries

The development of alternative electrocatalysts exhibiting high activity in the oxygen reduction reaction (ORR) is vital for the deployment of large-scale clean energy devices, such as fuel cells and zinc–air batteries. N-doped carbon materials offer a promising platform for the design and synthesis of electrocatalysts due to their high ORR activity, high surface area, and tunable porosity. In this study, materials in which MnO nanoparticles are entrapped in N-doped mesoporous carbon (MnO/NC) were developed as electrocatalysts for the ORR, and their performances were evaluated in zinc–air batteries. The obtained carbon materials had large surface area and high electrocatalytic activity toward the ORR. The carbon compounds were fabricated by using NaCl as template in a one-pot process, which significantly simplifies the procedure for preparing mesoporous carbon materials and in turn reduces the total cost. A primary zinc–air battery based on this material exhibits an open-circuit voltage of 1.49 V, which is higher than that of conventional zinc–air batteries with Pt/C (Pt/C cell) as ORR catalyst (1.41 V). The assembled zinc–air battery delivered a peak power density of 168 mW cm⁻² at a current density of about 200 mA cm⁻², which is higher than that of an equivalent Pt/C cell (151 mW cm⁻² at a current density of ca. 200 mA cm⁻²). The electrocatalytic data revealed that MnO/NC is a promising nonprecious-metal ORR catalyst for practical applications in metal–air batteries.     

Multifunctional Active-Center-Transferable Platinum/Lithium Cobalt Oxide Heterostructured Electrocatalysts towards Superior Water Splitting

Designing cost-effective and efficient electrocatalysts plays a pivotal role in advancing the development of electrochemical water splitting for hydrogen generation. Herein, multifunctional active-center-transferable heterostructured electrocatalysts, platinum/lithium cobalt oxide (Pt/LiCoO₂) composites with Pt nanoparticles (Pt NPs) anchored on LiCoO₂ nanosheets, are designed towards highly efficient water splitting. In this electrocatalyst system, the active center can be alternatively switched between Pt species and LiCoO₂ for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER), respectively. Specifically, Pt species are the active centers and LiCoO₂ acts as the co-catalyst for HER, whereas the active center transfers to LiCoO₂ and Pt turns into the co-catalyst for OER. The unique architecture of Pt/LiCoO₂ heterostructure provides abundant interfaces with favorable electronic structure and coordination environment towards optimal adsorption behavior of reaction intermediates. The 30 % Pt/LiCoO₂ heterostructured electrocatalyst delivers low overpotentials of 61 and 285 mV to achieve 10 mA cm⁻² for HER and OER in alkaline medium, respectively.     

Au/La2Ti2O7 Nanostructures Sensitized with Black Phosphorus for Plasmon‐Enhanced Photocatalytic Hydrogen Production in Visible and Near‐Infrared Light

Efficient utilization of solar energy is a high‐priority target and the search for suitable materials as photocatalysts that not only can harvest the broad wavelength of solar light, from UV to near‐infrared (NIR) region, but also can achieve high and efficient solar‐to‐hydrogen conversion is one of the most challenging missions. Herein, using Au/La₂Ti₂O₇ (BP‐Au/LTO) sensitized with black phosphorus (BP), a broadband solar response photocatalyst was designed and used as efficient photocatalyst for H₂ production. The optimum H₂ production rates of BP‐Au/LTO were about 0.74 and 0.30 mmol g⁻¹ h⁻¹ at wavelengths longer than 420 nm and 780 nm, respectively. The broad absorption of BP and plasmonic Au contribute to the enhanced photocatalytic activity in the visible and NIR light regions. Time‐resolved diffuse reflectance spectroscopy revealed efficient interfacial electron transfer from excited BP and Au to LTO which is in accordance with the observed high photoactivities.     

Platinum‐Decorated Au Porous Nanotubes as Highly Efficient Catalysts for Formic Acid Electro‐Oxidation

Au porous nanotubes (PNTs) were synthesized by a templating technique that involves the chemical synthesis of Ag nanowire precursors, electroless surface modification with Au, and selective etching. A subsequent galvanic replacement reaction between [PtCl₆]^2? and residual Ag generates Pt‐decorated Au porous nanotubes (Pt/Au PNTs), which represents a new type of self‐sustained high surface area electrocatalysts with ultra‐low Pt loading. Structural characterizations with scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X‐ray powder diffraction (XRD) reveal a novel nanoarchitecture with multimodal open porosity and excellent structural continuity and integrity. Cyclic voltammetry (CV) demonstrates that these Pt/Au PNTs possess very high electrocatalytic activity toward formic acid oxidation with enhanced tolerance to CO poisoning.     

RuP2‐Based Catalysts with Platinum‐like Activity and Higher Durability for the Hydrogen Evolution Reaction at All pH Values

Highly active, stable, and cheap Pt‐free catalysts for the hydrogen evolution reaction (HER) are under increasing demand for future energy conversion systems. However, developing HER electrocatalysts with Pt‐like activity that can function at all pH values still remains as a great challenge. Herein, based on our theoretical predictions, we design and synthesize a novel N,P dual‐doped carbon‐encapsulated ruthenium diphosphide (RuP₂@NPC) nanoparticle electrocatalyst for HER. Electrochemical tests reveal that, compared with the Pt/C catalyst, RuP₂@NPC not only has Pt‐like HER activity with small overpotentials at 10 mA cm⁻² (38 mV in 0.5 m H₂SO₄, 57 mV in 1.0 m PBS and 52 mV in 1.0 m KOH), but demonstrates superior stability at all pH values, as well as 100 % Faradaic yields. Therefore, this work adds to the growing family of transition‐metal phosphides/heteroatom‐doped carbon heterostructures with advanced performance in HER.     

AuPt Bipyramid Nanoframes as Multifunctional Platforms for In Situ Monitoring of the Reduction of Nitrobenzene and Enhanced Electrocatalytic Methanol Oxidation

Multifunctional metal nanostructures with a hollow feature, especially for nanoframes, are highly attractive owing to their high surface-to-volume ratios. However, pre-grown metal nanocrystals are always involved during the preparation procedure, and a synthetic strategy without the use of a pre-grown template is still a challenge. In this article, a template-free strategy is reported for the preparation of novel AuPt alloy nanoframes through simply mixing HAuCl₄ and H₂PtCl₆ under mild conditions. The alloy nanostructures show a bipyramid-frame hollow architecture with the existence of only the ten ridges and absence of their side faces. This is the first report of bipyramid-like nanoframes and a template-free method under mild conditions. This configuration merges the plasmonic features of Au and highly active catalytic sites of Pt in a single nanostructure, making it an ideal multifunctional platform for catalyzing and monitoring the catalytic reaction in real time. The superior catalytic activity is demonstrated by using the reduction of nitrobenzene to the corresponding aminobenzene as a model reaction. More importantly, the AuPt nanoframes can track the reduction process on the basis of the SERS signals of the reactants, intermediates, and products, which helps to reveal the reaction mechanism. In addition, the AuPt nanoframes show much higher electrocatalytic properties toward the methanol oxidation reaction than commercial Pt/C electrocatalysts.     

Facile Synthesis of Quasi‐One‐Dimensional Au/PtAu Heterojunction Nanotubes and Their Application as Catalysts in an Oxygen‐Reduction Reaction

An intermediate‐template‐directed method has been developed for the synthesis of quasi‐one‐dimensional Au/PtAu heterojunction nanotubes by the heterogeneous nucleation and growth of Au on Te/Pt core–shell nanostructures in aqueous solution. The synthesized porous Au/PtAu bimetallic nanotubes (PABNTs) consist of porous tubular framework and attached Au nanoparticles (AuNPs). The reaction intermediates played an important role in the preparation, which fabricated the framework and provided a localized reducing agent for the reduction of the Au and Pt precursors. The Pt₇Au PABNTs showed higher electrocatalytic activity and durability in the oxygen‐reduction reaction (ORR) in 0.1 M HClO₄ than porous Pt nanotubes (PtNTs) and commercially available Pt/C. The mass activity of PABNTs was 218 % that of commercial Pt/C after an accelerated durability test. This study demonstrates the potential of PABNTs as highly efficient electrocatalysts. In addition, this method provides a facile strategy for the synthesis of desirable hetero‐nanostructures with controlled size and shape by utilizing an intermediate template.     

Au Nanoparticles Modified with Pt,Ru and SnO2 as Electrocatalysts for Ethanol Oxidation Reaction in Acids

The anodic reaction in direct ethanol fuel cells (DEFCs), ethanol oxidation reaction (EOR) faces challenges, such as incomplete electrooxidation of ethanol and high cost of the most efficient electrocatalyst, Pt in acidic media at low temperature. In this study, core‐shell electrocatalysts with an Au core and Pt‐based shell (Au@Pt) are developed. The Au core size and Pt shell thickness play an important role in the EOR activity. The Au size of 2.8 nm and one layer of Pt provide the most optimized performance, having 6 times higher peak current density in contrast to commercial Pt/C. SnO₂ as a support also enhances the EOR activity of Au@Pt by 1.73 times. Further modifying the Pt shell with Ru atoms achieve the highest EOR current density that is 15 and 2.5 times of Pt/C and Au@Pt. Our results suggest the importance of surface modification in rational design of advanced electrocatalysts.     

General synthesis of Pt and Ni co-doped porous carbon nanofibers to boost HER performance in both acidic and alkaline solutions

It is essential to develop efficient electrocatalysts to generate hydrogen from water electrolysis for hydrogen economy. In this work, platinum(Pt) and nickel(Ni) co-doped porous carbon nanofibers(Pt/NiPCNFs) with low Pt content were prepared via an electrospinning, carbonization and galvanic replacement reaction. Because of the high electrical conductivity, abundant electrochemical active sites and synergistic effect between Pt and Ni nanoparticles, the optimized Pt/Ni-PCNFs catalyst shows an e...     

Hierarchical Architectures Based on Ru Nanoparticles/Oxygen-Rich-Carbon Nanotubes for Efficient Hydrogen Evolution

Highly active and durable electrocatalysts are essential for producing hydrogen fuel through the hydrogen evolution reaction (HER). Here, a uniform deposition of Ru nanoparticles strongly interacting with oxygen-rich carbon nanotube architectures (Ru-OCNT) through ozonation and hydrothermal approaches has been designed. The hierarchical structure of Ru-OCNT is made by self-assembly of oxygen functionalities of OCNT. Ru nanoparticles interact strongly with OCNT at the Ru/OCNT interface to give excellent catalytic activity and stability of the Ru-OCNT, as further confirmed by density functional theory. Owing to the hierarchical structure and adjusted surface chemistry, Ru-OCNT has an overpotential of 34 mV at 10 mA cm⁻² with a Tafel slope of 27.8 mV dec⁻¹ in 1 M KOH, and an overpotential of 55 mV with Tafel slope of 33 mV dec⁻¹ in 0.5 M H₂SO₄. The smaller Tafel slope of Ru-OCNT than Ru-CNT and commercial Pt/C in both alkaline and acidic electrolytes indicates high catalytic activity and fast charge transfer kinetics. The as-proposed chemistry provides the rational design of hierarchically structured CNT/nanoparticle electrocatalysts for HER to produce hydrogen fuel.     

Boosting the photocatalytic nitrogen reduction to ammonia through adsorption-plasmonic synergistic effects

Ammonia is one of the most essential chemicals in the modern society but its production still heavily relies on energy-consuming Haber-Bosch processes. The photocatalytic reduction of nitrogen with water for ammonia production has attracted much attention recently due to its synthesis under mild conditions at room temperature and atmospheric pressure using sunlight. Herein, we report a high-performance Au/MIL-100(Cr) photocatalyst, comprising MIL-100(Cr) and Au nanoparticles in photocatalytic nitrogen reduction to ammonia at ambient conditions under visible light irradiation. The optimized photocatalyst (i.e., 0.10Au/MIL-100(Cr)) achieved the excellent ammonia production rate with 39.9 µg g_cat^?1 h^?1 compared with pure MIL-100(Cr) (2.73 µg g_cat^?1 h^?1), which was nearly 15 times that on pure MIL-100(Cr). The remarkable activity could be attributed to the adsorption-plasmonic synergistic effects in which the MIL-100(Cr) and Au are responsible to the strong trapping and adsorption of N₂ molecules and photo-induced plasmonic hot electrons activating and decomposing the N₂ molecules, respectively. This study might provide a new strategy for designing an efficient plasmonic photocatalyst to improve the photocatalytic performance of N₂ fixation under visible light irradiation.     

2D Metal–Organic Framework Derived CuCo Alloy Nanoparticles Encapsulated by Nitrogen-Doped Carbonaceous Nanoleaves for Efficient Bifunctional Oxygen Electrocatalyst and Zinc–Air Batteries

The development of efficient bifunctional electrocatalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) still remains a challenge in a wide range of renewable energy technologies. Herein, CuCo alloy nanoparticles encapsulated by nitrogen-doped carbonaceous nanoleaves (CuCo-NC) have been synthesized from a Cu(OH)₂/2D leaf-like zeolitic imidazolate framework (ZIF-L)-pyrolysis approach. Leaf-like Cu(OH)₂ is first prepared by the ultrasound-induced self-assembly of Cu(OH)₂ nanowires. The efficient encapsulation of Cu(OH)₂ in ZIF-L is obtained owing to the morphology fitting between the leaf-like Cu(OH)₂ and ZIF-L. CuCo-NC catalysts present superior electrocatalytic activity and stability toward ORR and OER over the commercial Pt/C and IrO₂, respectively, which are further used as bifunctional oxygen electrocatalysts in Zn–air batteries and exhibit impressive performance, with a high peak power density of 303.7 mW cm⁻², large specific capacity of up to 751.4 mAh g⁻¹ at 20 mA cm⁻², and a superior recharge stability.     

Direct Observation of Dynamic Bond Evolution in Single-Atom Pt/C3N4 Catalysts

Single-atom catalysts are promising platforms for heterogeneous catalysis, especially for clean energy conversion, storage, and utilization. Although great efforts have been made to examine the bonding and oxidation state of single-atom catalysts before and/or after catalytic reactions, when information about dynamic evolution is not sufficient, the underlying mechanisms are often overlooked. Herein, we report the direct observation of the charge transfer and bond evolution of a single-atom Pt/C₃N₄ catalyst in photocatalytic water splitting by synchronous illumination X-ray photoelectron spectroscopy. Specifically, under light excitation, we observed Pt−N bond cleavage to form a Pt⁰ species and the corresponding C=N bond reconstruction; these features could not be detected on the metallic platinum-decorated C₃N₄ catalyst. As expected, H₂ production activity (14.7 mmol h⁻¹ g⁻¹) was enhanced significantly with the single-atom Pt/C₃N₄ catalyst as compared to metallic Pt-C₃N₄ (0.74 mmol h⁻¹ g⁻¹).