岩矿中微量砷的测定——砷锑钼蓝比色法

近年来应用砷锑钼蓝三元络合物光度测定试样中的砷被认为是较理想的方法,但用于化探样品分析还存在着空白值高和灵敏度低的问题。本文在前人工作的基础上,针对化探样品组分各异,含量变化大,干扰元素多,灵敏度和准确度要求高的特点,对用砷化氢发生分离富集,砷锑钼蓝法测砷进行了一系列的     

发射光谱光电直读法测定高纯铝中的微量杂质

发射光谱光电直读(简称“光电法”)直接分析固体样品,具有快速、准确、多元素同时测定等优点,但以往的方法,灵敏度都比较低。鹿岛次郎等报导,光电法直接测定高纯铝固体样品中的Fe、Si和Cu时,它们的分析含量范围分别为0.001—1.5％,0.001—2.0％和0.001—1.0％,当它们的含量低于0.01时,分析精度(相对均方偏差)为10％.美国利用1.5米或20米光栅光电直读光谱仪分析上述含量元素时,所得的工作曲线形状是非线性的。     

X射线荧光光谱法测定铁基合金中合金组分的通用工作曲线的制作——基本参数(FP)法虚拟合成标准样品的应用

应用基本参数(FP)法虚拟合成标准样品制作了X射线荧光光谱法测定不同类型的铁基合金中的26种元素的通用工作曲线。选择最佳的仪器工作条件和合理的待测元素的分析线系,测定了9种元素、受共存元素重叠干扰的校正系数,用瑞利散射线扣除背景及通道材料的影响。在设定虚拟合成标准样品中各元素的含量,并算得在此设定值下的理论荧光强度后,用FP法计算各元素在其定值下的最终强度,从而完成了FP法工作曲线。应用此虚拟合成单标工作曲线对多种标准样品进行测定,证明该工作曲线可用于各种类型的铁基合金的分析。     

电感耦合等离子体发射光谱(ICP-OES)法测定不锈钢中的硅、锰、磷、铬、镍、钼、铜

用HCl-HNO3混和酸溶解不锈钢样品,用钇为内标物质,使用标准样品绘制工作曲线,用电感耦合等离子体发射光谱(ICP-OES)法测定了不锈钢中的硅、锰、磷、铬、镍、钼、铜。在选定的操作条件下,对不锈钢标准样品按实验方法进行测定,标准样品的测定值与标准值基本吻合。元素质量分数在0.01%～0.10%时,相对标准偏差(n=11)RSD5%;质量分数大于0.10%,RSD 1%。同时测定不锈钢中的硅、锰、磷、铬、镍、钼、铜元素的含量,操作简单、快速、灵敏度高,结果令人满意。     

微波消解样品-电感耦合等离子体原子发射光谱法测定植物中9种必需元素

植物样品置于聚四氟乙烯罐中,加入硝酸及过氧化氢后在MARS 5微波消解仪中按设定程序加热消解.样品溶液经定容为一定体积并保持一致的稀硝酸酸度,直接进样进行电感耦合等离子体原子发射光谱法(ICP-AES)分析,在选定的优化分析条件下同时测定其9种元素(钾、钙、镁、磷、硼、锌、铜、铁及锰)的含量.包括样品消解在内,分析全过程只需3～4 h.用标准曲线法进行定量,所得各元素的标准曲线均有良好的线性关系.应用此方法分析了一种茶叶标准物质(GBW 07605),所得9种元素的测定结果与证书值相符,各元素测定值的相对标准偏差(n=5)在0.3%～4.7%之间.     

氢氟酸直接进样-电感耦合等离子体原子发射光谱法(ICP-AES)测定氧化锆中多种杂质元素

采用氢氟酸微波消解法前处理氧化锆材料,使用氢氟酸进样系统,不需要赶酸直接测定GBW06602氧化锆标准样品中的多元素含量,根据样品情况确定了最佳分析条件和最佳分析谱线。实验结果表明,测定元素线性关系及重复性良好,定量准确,可同时测定氧化锆中的多种金属元素,该方法检出限低,精密度高,分析结果与标准值相吻合,完全满足氧化锆中多元素杂质含量的工业分析要求。     

X射线荧光光谱法测定镍基高温合金中合金组分的通用工作曲线的制作——基本参数(FP)法虚拟合成标准样品的应用

应用基本参数(FP)法虚拟合成标样制作了X射线荧光光谱法(XRFS)测定不同类型的镍基高温合金中18种合金元素和4种杂质元素的通用工作曲线。选择了最佳的仪器工作条件和合理的待测元素的分析线系,测定了9种元素受共存元素分析线重叠干扰的校正系数,用瑞利散射线扣除背景及通道材料的影响。在设定虚拟合成标样中各元素的含量,并算得在此设定值下的荧光强度后,用FP法计算各元素在其定值下的最终强度,从而完成了FP法工作曲线。应用此虚拟合成单标工作曲线对多种标准样品进行测定,证明该工作曲线可通用于各种类型的镍基高温合金的分析。     

火焰原子吸收光谱法测定木瓜中7种微量元素的含量

采用火焰原子吸收法测定光皮木瓜中钙,铜,铁,硒,锌,锰,镁等微量元素的含量。优化了仪器工作条件,利用标准曲线法对待测样品进行定量分析。在设定的浓度范围内,7种元素的质量浓度与吸光度呈良好的线性关系,相关系数为0.992 9～0.999 4,7种元素的检出限为0.211～9.268 mg/L。对样品进行7次重复测定,测定结果的相对标准偏差均小于3.0%,加标浓度为1.000 0～10.010 0 mg/L时,加标回收率为96.51%～104.55%。该方法具有操作简单、干扰少等优点,为木瓜的开发提供了科学依据。     

电感耦合等离子体质谱法测定核级海绵锆及锆合金中16种痕量杂质元素北大核心CSCD

取样品0.600 0 g,加入10 mL水润湿后,用5 mL氢氟酸和5 mL硝酸溶解,用水定重至60.0 g。选择灵敏度高且干扰小的同位素,以标准加入法补偿基体效应制作工作曲线,在射频功率1 100 W,雾化气流量0.87 L·min^(-1)等条件下,采用电感耦合等离子体质谱法同时测定核级海绵锆及锆合金中16种杂质元素的含量。结果表明,16种元素的检出限(3s)为0.007~0.26μg·g^(-1)。测定核级海绵锆样品11次,各元素测定值的相对标准偏差(RSD)为2.2%~8.0%。按照标准加入法进行回收试验,回收率为90.0%~111%。     

电感耦合等离子体质谱法测定金银花中6种有毒元素

建立电感耦合等离子体质谱法同时测定金银花中铅、镉、铬、镍、铜、砷6种有毒元素含量。采用微波消解法进行前处理,以钪、铟、铋3种元素作为内标物,用电感耦合等离子体质谱法对50批金银花样品中铅、镉、铬、镍、铜、砷6种有毒元素含量进行测定,以内标法定量,并应用SPSS软件对测定值进行统计学分析。6种有毒元素的质量浓度在0~300μg/L范围内线性良好,相关系数均不小于0.9997。6种有毒元素的检出限为0.003~0.020 mg/kg,样品加标回收率为80.0%~111.0%,相对标准偏差为0.71%~3.82%(n=6)。50批金银花样品中共计有14批样品有毒元素含量超出2015年版《中华人民共和国药典》规定,超标率为28%。聚类分析将50批样品分为3大类。该方法操作简单,灵敏度高,专属性好,可准确快速地同时测定金银花中多种有毒元素含量,可作为中药材品质及安全性监管的技术手段。     

Expanding the linear dynamic range in quantitative high performance liquid chromatography/tandem mass spectrometry by the use of multiple product ions

A strategy for expanding the linear working range in bioanalysis using quantitative high performance liquid chromatography/tandem mass spectrometry (HPLC/MS/MS) is presented. The strategy involves monitoring multiple product ions. Herein we demonstrate the strategy on a rat plasma assay for a proprietary experimental drug where the linear range is expanded from 2 to 4 orders of magnitude. A primary sensitive ion was monitored to obtain a high sensitivity range calibration curve (0.400 to 100 ng/mL) while a less sensitive secondary ion was monitored to obtain a low sensitivity range calibration curve (90.0 to 4000 ng/mL). Each calibration curve gave acceptable linearity (r >0.990). Quality control samples at low, mid and high levels within each calibration curve demonstrated acceptable precision and accuracy (within 20% for all levels). The technique was successfully applied to rat pre-clinical sample analysis.     

Determination of analytical limits in solid sampling ETAAS: a new approach towards the characterization of analytical quality in rapid methods

In the present study the lower analytical limits of solid sampling electrothermal atomization atomic absorption spectrometry (SS-ETAAS) were characterized by means of blank measurements and – for the first time – by means of the calibration curve method, where a calibration near the range of these limits (limit of decision, detection and quantification) was performed. The limit of decision as derived from blank measurements was calculated according to the 3σ-criterion to be 0.003 and 0.019 ng for Cd and Pb, respectively. For Pb and Cd a roughly threefold increase of these limits was observed when the calibration method according to DIN 32 645 was applied. When solid reference material was used, only a slight increase could be observed. The analytical limits were 2 to 20 times lower than reported for sample decomposition methods. The blank measurement and conventional calibration curve method, however, do not account for factors relating to solid sampling such as sample mass and matrix. Therefore, the calibration curve model was applied to data derived from comparisons between direct solid sampling ETAAS and a compound reference method (ETAAS following sample homogenization and digestion). The observed analytical limits were not found to be substantially increased if enough samples with low element contents were available for calibration. Coupling of the calibration curve model with the comparison of methods included real test samples and thus the relevant maximum sample mass and analyte content in the range of the lower analytical limits. As validation procedures frequently include comparisons of methods, the present approach might prove to be of some general interest for the characterization of analytical quality in rapid methods.     

Determination of analytical limits in solid sampling ETAAS: a new approach towards the characterization of analytical quality in rapid methods

In the present study the lower analytical limits of solid sampling electrothermal atomization atomic absorption spectrometry (SS-ETAAS) were characterized by means of blank measurements and--for the first time--by means of the calibration curve method, where a calibration near the range of these limits (limit of decision, detection and quantification) was performed. The limit of decision as derived from blank measurements was calculated according to the 3sigma-criterion to be 0.003 and 0.019 ng for Cd and Pb, respectively. For Pb and Cd a roughly three-fold increase of these limits was observed when the calibration method according to DIN 32 645 was applied. When solid reference material was used, only a slight increase could be observed. The analytical limits were 2 to 20 times lower than reported for sample decomposition methods. The blank measurement and conventional calibration curve method, however, do not account for factors relating to solid sampling such as sample mass and matrix. Therefore, the calibration curve model was applied to data derived from comparisons between direct solid sampling ETAAS and a compound reference method (ETAAS following sample homogenization and digestion). The observed analytical limits were not found to be substantially increased if enough samples with low element contents were available for calibration. Coupling of the calibration curve model with the comparison of methods included real test samples and thus the relevant maximum sample mass and analyte content in the range of the lower analytical limits. As validation procedures frequently include comparisons of methods, the present approach might prove to be of some general interest for the characterization of analytical quality in rapid methods.     

Adaptation of microthermal probes for the determination of biochemical species

A glucose sensitive enzymatic thermal sensor based on a pair of commercial microthermal probes was fabricated by cross-linking of the corresponding enzymes (glucose oxidase and catalase) with bovine serum albumin onto the chip surfaces. The characteristics of this sensor were optimised by testing it in different conditions. To find the maximal sensitivity, the calibration curves of this sensor were measured in different buffer solutions with and without the addition of H(2)O(2) to the analysed samples at various rates of sample flow stream. Different buffer solutions and hydrogen peroxide concentraions were used to realise the principles of a chemical and biochemical amplification of the biosensor response. It was shown that the level of the biosensor response and its dynamic range increase if hydrogen peroxide is added to the analysed samples and depend on the type of buffer solutions tested and the rate of the sample flow stream.     

Optimal speed as a function of system performance for continuous flow analyzers

The limitation to high rates of sample throughput with continuous flow automated analyzers is unacceptably high sample-to-sample carry-over. Previous programs for carry-over correction have involved relatively large computer capacities. Here, the simple expression derived for carry-over can be easily programmed in BASIC for a Commodore PET operating in real time. The program includes peak picking and calculation of the calibration graph and sample concentrations. At 240 samples per hour, the results obtained for total protein (linear calibration graph) and haptoglobin (non-linear calibration plot) showed acceptable precision and recovery and correlated well with the same determination conducted at normal operating speeds. Standard Auto Analyzer equipment was used througout. A parameter which monitors the instrument function is also calculated; this replaces the conventional visual examination of the curve for function monitoring. At high sample rates with degraded curves, visual curve examination is not effective.     

交互模式-电感耦合等离子体质谱(ICP-MS)法测定生态地球化学植物样品中7种金属元素

植物样品中各元素的含量,是评价土壤质量及健康的重要指标。为满足测定大批量生态地球化学植物样品中多金属元素分析要求,建立了交互模式-ICP-MS法测定植物样品中7种痕量金属元素的定量分析方法。讨论了ICP-MS的STD、KED（He）、交互模式3种方法测定植物样品中7种金属元素结果。实验结果表明：利用工作曲线法配制Hg标准溶液,更改82Se在线校正方程系数为1.83,在ICP-MS的交互模式下测定植物样品中82Se,63Cu,60Ni,66Zn,111Cd,75As、202Hg可以得到准确可靠的结果,克服了植物样品中Se和Hg元素测定的难题。基于所建方法各元素校准曲线系数＞0.999;方法检出限为0.0004~0.08mg/kg;加标回收率在96.2%-107%之间;测定GBW10010a（大米）、GBW10012（玉米）、GBW10021（豆角）3种标准物质,结果均在参考值范围内,相对标准偏差RSD＜10%。该方法前处理简单、灵敏度高、准确度高、分析速度快,适用于生态地球化学评价植物样品多金属元素同时测定。为地球化学调查工作中分析测试植物样品中金属多元素的快速测定提供了新思路。     

自动快速燃烧－离子色谱测定铜精矿中的氟

建立了自动快速燃烧（AQF）－离子色谱联用测定铜精矿中氟的方法。将 AQF 的自动化特性和离子色谱的灵敏度高、准确性好的特点结合起来,能够实现操作过程的连续自动化。结果表明,线性范围内（1.0?50.0 μg )校准曲线相关系数 r >0. 999,氟的检出限为0.0004%。按照实验方法测定铜精矿样品中氟,结果的相对标准偏差（ RSD ,n =6)为2.14 % ?4.24 %。将实验方法用于铜精矿标准样品氟含量测定,测定值与认定值吻合较好;方法对照试验表明,实验方法对氟含量的测定值与国家标准 GB/T 3884. 12—2010的测定值基本一致。     

Determination of MK-0431 in human plasma using high turbulence liquid chromatography online extraction and tandem mass spectrometry

A robust and sensitive method using high turbulence liquid chromatography (HTLC) online extraction with tandem mass spectrometry (MS/MS) for the determination of MK-0431 in human plasma was developed and validated to support the clinical studies. This HTLC online extraction method eliminated the time-consuming offline sample extraction procedures and significantly increased productivity. A narrow bore large particle size reversed-phase column (Cyclone, 50 x 1.0 mm, 60 microm) and a BDS Hypersil C18 column (30 x 2.1 mm, 3 microm) were used as extraction and analytical columns, respectively. The linear dynamic range of the calibration curve was 0.5 to 1000 ng/mL. Intraday validation was conducted using five calibration curves prepared in five lots of human control plasma, and the intraday precision (RSD%) was from 2.4 to 9.0% and the accuracy was from 98.0 to 103% of the nominal value. The intraday precision (RSD%, n = 5) for plasma quality control (QC) samples varied from 2.0 to 5.3% and accuracy from 103 to 105% of the nominal value. The interday precision (RSD%) for 100 sets of plasma QC samples in 29 analytical runs varied from 6.3 to 9.0% and the accuracy from 98.8 to 104% of the nominal value. No significant difference was observed between the interday and intraday precision and accuracy of the QC samples.     

Total protein determinations by particle beam/hollow cathode optical emission spectroscopy (PB/HC-OES) system III: Investigation of carrier salts for enhanced particle transport

Particle beam hollow cathode optical emission spectroscopy (PB/HC-OES) is evaluated as a generic tool for total protein determinations by monitoring the carbon atomic emission (C (I) 193.0 nm) resultant from dissociated analyte species. Previous studies demonstrated the capability of the PB/HC-OES system for total protein determinations with limits of detection for bovine serum albumin (BSA) samples being at the single-nanogram level for 200 l injections. Non-linear behavior across the concentration range in the calibration curve was observed due to the poor transport of small particles (owing to low analyte concentrations) through the PB interface. The potential use of non-volatile salts as carrier agents is investigated in the determination of protein samples by PB/HC-OES. A range of chloride salts (different cations), potassium salts (different anions), and an organic modifier (ammonium acetate) is investigated here for possible use as carriers upon addition as sample injection matrices for protein samples. The analyte response curves of BSA samples with KCl added as the sample injection matrix show higher sensitivity, better linearity (R²) and subsequently lower detection limits in comparison to those obtained with water, HCl, KNO₃ or ammonium acetate as carrier matrices.     

Sub part-per-million mass accuracy by using stepwise-external calibration in fourier transform ion cyclotron resonance mass spectrometry

A new external calibration procedure for FT-ICR mass spectrometry is presented, stepwise-external calibration. This method is demonstrated for MALDI analysis of peptide mixtures, but is applicable to any ionization method. For this procedure, the masses of analyte peaks are first accurately measured at a low trapping potential (0.63 V) using external calibration. These accurately determined (< 1 ppm accuracy) analyte peaks are used as internal calibrant points for a second mass spectrum that is acquired for the same sample at a higher trapping potential (1.0 V). The second mass spectrum has a approximately 10-fold improvement in detection dynamic range compared with the first spectrum acquired at a low trapping potential. A calibration equation that accounts for local and global space charge is shown to provide mass accuracy with external calibration that is nearly identical to that of internal calibration, without the drawbacks of experimental complexity or reduction of abundance dynamic range. For the 609 mass peaks measured using stepwise-external calibration method, the root-mean-square error is 0.9 ppm. The errors appear to have a Gaussian distribution; 99.3% of the mass errors are shown to lie within three times the sample standard deviation (2.6 ppm) of their true value.