Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Synthesis,characterization of B-doped TiO<Subscript>2</Subscript> nanotubes with high photocatalytic activity

B-doped TiO₂ nanotubes (B/TiO₂ NTs) were prepared by the combination of sol–gel process with hydrothermal treatment. The prepared catalysts were characterized by XRD, TEM and XPS. The photocatalytic activity of B/TiO₂ NTs was evaluated through the photodegradation of aqueous methyl orange. The results demonstrated that the 1.5% B/TiO₂ NTs calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with B significantly enhanced the photocatalytic efficiency.     

The preparation and characterization of La doped TiO2 nanoparticles and their photocatalytic activity

In this paper, pure and La doped TiO₂ nanoparticles with different La content were prepared by a sol-gel process using Ti (OC₄H₉)₄ as raw material, and also were characterized by XRD, TG-DTA, TEM, XPS, DRS and Photoluminescence (PL) spectra. We mainly investigated the effects of calcining temperature and La content on the properties and the photocatalytic activity for degrading phenol of as-prepared TiO₂ samples, and also discussed the relationships between PL spectra and photocatalytic activity as well as the mechanisms of La doping on TiO₂ phase transformation. The results showed that La³⁺ did not enter into the crystal lattices of TiO₂ and was uniformly dispersed onto TiO₂ as the form of La₂O₃ particles with small size, which possibly made La dopant have a great inhibition on TiO₂ phase transformation; La dopant did not give rise to a new PL signal, but it could improve the intensity of PL spectra with a appropriate La content, which was possibly attributed to the increase in the content of surface oxygen vacancies and defects after doping La; La doped TiO₂ nanoparticles calcined at 600°C exhibited higher photocatalytic activity, indicating that 600°C was an appropriate calcination temperature. The order of photocatalytic activity of La doped TiO₂ samples with different La content was as following: 1>1.5>3>0.5>5>0 mol%, which was the same as the order of their PL intensity, namely, the stronger the PL intensity, the higher the photocatalytic activity, demonstrating that there were certain relationships between PL spectra and photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions.     

Synthesis of TiO2 (B) and High‐temperature Stable Anatase TiO2 Nanowires by Hydrothermal Method and Investigation of Photocatalytic Activity

In this study, TiO₂ nanowires (TNWs) were synthesized through hydrothermal method and were characterized using X‐Ray diffraction (XRD), transmission electron microscopy (TEM) and BET techniques. Monoclinic TiO₂ (B) is the dominant phase of TNWs up to 600°C which is completely transformed into a highly crystalline anatase phase at 800°C. The photocatalytic activity of TNWs, prepared at various calcination temperatures, was investigated in the removal of Rhodamine B as an organic model pollutant. The results indicated that the photocatalytic activity of TNWs, prepared at 800°C calcination temperature, was better than that of other samples and even TiO₂–P25 nanoparticles.     

Preparation of TiO<Subscript>2</Subscript> nanofibers immobilized on quartz substrate by electrospinning for photocatalytic degradation of ranitidine

The photocatalytic activity of TiO₂ nanofibers immobilized on quartz substrates was investigated by evaluating the decomposition of organic pollutants. TiO₂ nanofibers were synthesized by electrospinning the Ti-precursor/polymer mixture solution, followed by hot-pressing for enhancing the adhesion of TiO₂-nanofiber films to the substrates. TiO₂ started to crystalize in the anatase form at 500 °C and reached the optimal photocatalytic anatase/rutile phase ratio of 70:30 at a calcination temperature of 600 °C. The TiO₂-nanofiber film was demonstrated to be an efficient photocatalyst by ranitidine decomposition under UV illumination and was proven to have a comparable photocatalytic activity with the well-known Degussa P25 nanoparticulate photocatalyst and excellent recyclability during 10 cycles of photocatalytic operation, indicating no loss of TiO₂ nanofibers during photocatalytic operations.     

Effect of calcination temperature on the photocatalytic activity of carbon‐doped titanium dioxide revealed by photoluminescence study

Carbon‐doped titania (C‐TiO₂) nanoparticles were synthesized by the sol–gel method at different calcination temperatures (300–600°C) employing titanium tetraisopropoxide (TTIP) as the titanium source and polyoxyethylene sorbitan monooleate (Tween 80) as the carbon source. The physical properties of C‐TiO₂ samples were characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). The photocatalytic activities were checked through the photodegradation of phenolphthalein (PHP) under ultraviolet irradiation. The UV spectrum showed that the carbon doping extends the absorption range of TiO₂ to the visible region. However, the photocatalytic activity is affected by the electron–hole recombination phenomenon, as revealed by the photoluminescence (PL) study. According to the PL spectra, carbon doping reduces the edge‐to‐edge electron–hole recombination. Nevertheless, the number of defect sites is greatly influenced by the calcination temperature of C‐TiO₂. C‐TiO₂ that was calcined at 400°C showed the highest photodegradation percentage of PHP, which was mainly attributed to the synergic effect of the low direct edge‐to‐edge electron–hole recombination, high content of defect sites, and retention of active electrons on the surface hydroxyl group.     

Microemulsion synthesis, characterization of highly visible light responsive rare Earth-doped bi(2) o(3)

In this paper, Bi₂O₃ and rare earth (La, Ce)‐doped Bi₂O₃ visible‐light‐driven photocatalysts were prepared in a Triton X‐100/n‐hexanol/cyclohexane/water reverse microemulsion. The resulting materials were characterized by X‐ray powder diffraction (XRD), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET) surface area, photoluminescence spectra (PLS) and UV–Vis diffuse reflectance spectroscopy. The XRD patterns of the as‐prepared catalysts calcined at 500°C exhibited only the characteristic peaks of monoclinic α‐Bi₂O₃. PLS analysis implied that the separation efficiency for electron‐hole has been enhanced when Bi₂O₃ was doped with rare earth. UV–Vis diffuse reflectance spectroscopy measurements presented an extension of light absorption into the visible region. The photocatalytic activity of the samples was evaluated by degradation of methyl orange (MO) and 2,4‐dichlorophenol (2,4‐DCP). The results displayed that the photocatalytic activity of rare earth‐doped Bi₂O₃ was higher than that of dopant‐free Bi₂O₃. The optimal dopant amount of La or Ce was 1.0 mol%. And the mechanisms of influence on the photocatalytic activity of the catalysts were discussed.     

Template‐free Fabrication of Hierarchical Macro‐/mesoporous N‐doped TiO2/graphene Oxide Composites with Enhanced Visible‐light Photocatalytic Activity

Hierarchical macro‐/mesoporous N‐doped TiO₂/graphene oxide (N‐TiO₂/GO) composites were prepared without using templates by the simple dropwise addition mixed solution of tetrabutyl titanate and ethanol containg graphene oxide (GO) to the ammonia solution, and then calcined at 350 °C. The as‐prepared samples were characterized by scanning electron microscopy (SEM), Brunauer‐Emmett‐Teller (BET) surface area, X‐ray diffraction (XRD), Raman spectroscopy, X‐ray photoelectron spectroscopy (XPS), and UV‐Vis absorption spectroscopy. The photocatalytic activity was evaluated by the photocatalytic degradation of methyl orange in an aqueous solution under visible‐light irradiation. The results show that N‐TiO₂/GO composites exhibited enhanced photocatalytic activity. GO content exhibited an obvious influence on photocatalytic performance, and the optimal GO addition content was 1 wt%. The enhanced photocatalytic activity could be attributed to the synergetic effects of three factors including the improved visible light absorption, the hierarchical macro‐mesoporous structure, and the efficient charge separation by GO.     

Graphene Nanosheets as a Platform for the 2D Ordering of Metal Oxide Nanoparticles: Mesoporous 2D Aggregate of Anatase TiO2 Nanoparticles with Improved Electrode Performance

Graphene nanosheets are successfully applied as an effective platform for the 2D ordering of metal oxide nanoparticles. Mesoporous 2D aggregates of anatase TiO₂ nanoparticles are synthesized by the heat treatment of the uniformly hybridized nanocomposite of layered titanate–reduced graphene oxide (RGO) at elevated temperatures. The precursor layered titanate–RGO nanocomposite is prepared by self‐assembly of anionic RGO nanosheets and cationic TiO₂ nanosols. The calcination of the as‐prepared layered titanate–RGO nanocomposite at 500 °C induces a structural and morphological change of layered titanate nanoplates into anatase TiO₂ nanoparticles without significant modification of the RGO nanosheet. Increasing the heating temperature to 600 °C gives rise to elimination of the RGO component, leading to the formation of sheetlike porous aggregates of RGO‐free TiO₂ nanoparticles. The nanocomposites calcined at 500–700 °C display promising functionality as negative electrodes for lithium ion batteries. Among the present calcined derivatives, the 2D sheet‐shaped aggregate of TiO₂ nanoparticles obtained from calcination at 600 °C delivers the greatest specific discharge capacity with good capacity retention for all current density conditions applied. Such superior electrode performance of the nanocomposite calcined at 600 °C is attributable both to the improved stability of the crystal structure and crystal morphology of titania and to the enhancement of Li⁺ ion transport through the enlargement of mesopores. The present findings clearly demonstrate the usefulness of RGO nanosheets as a platform for 2D‐ordered superstructures of metal oxide nanoparticles with improved electrode performance.     

Preparation of TiO2 nanocrystallites by hydrolyzing with gaseous water and their photocatalytic activity

TiO₂ nanocrystallites were prepared from precursors tetra-n-butyl titanate (Ti(OC₄H₉)₄) and titanium tetrachloride (TiCl₄). The precursors were hydrolyzed by gaseous water in autoclave, and then calcined at predetermined testing temperatures. The samples were characterized by X-ray diffraction (XRD), thermogravimetry–differential thermal analysis (TG–DTA), field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectra (FT-IR), and UV–vis diffuse reflectance spectra (DRS). The photocatalytic activities of the samples were evaluated by the photobleaching of methylene blue (MB) in aqueous solution and the photocatalytic oxidation of propylene in gas phase at ambient temperature. The results showed that the anatase phase nanocrystalline TiO₂ could be obtained at relatively low temperatures (for precursor Ti(OC₄H₉)₄ at 110 °C and for TiCl₄ at 140 °C, respectively), and that the as prepared samples exhibited high photocatalytic activities to photobleach MB in aqueous solution. As the calcination temperatures increasing, the decolor ratio of MB increased and reached the maximum value of nearly 100% at 600 °C, and then decreased. The photobleaching of MB by all samples followed the pseudo-first-order kinetics with respect to MB concentration. The photodecomposition amount of propylene by TiO₂ nanocrystallites calcined at 600 °C from precursor of Ti(OC₄H₉)₄ is 21.6%, which is approaching to that by Degussa P25 TiO₂ (24.9%).     

Preparation and characterization of transparent TiO2 thin films coated on fused-silica substrates

The transparent TiO₂ thin films coated on fused-SiO₂ substrates were prepared by the sol–gel method and spin-coating technique. Effects of calcination temperature on crystal structure, grain size, surface texture, and light transmittance of the films were investigated. After calcining at 600–1,200 °C, the thicknesses of the TiO₂ films were all around 80 nm and the molecular structures of the films were anatase, even at 1,200 °C. The calcined TiO₂ films had the ultraviolet light (wavelength 200–400 nm) transmittances of ≤29% and the visible light (wavelength 400–800 nm) transmittance of ≥72%. By photocatalytically decomposing the methylene blue (MB) in water, the photocatalytic activities of the TiO₂ thin films were measured and represented using the characteristic time constant (τ) for the MB degradation. While the films prepared at 1,000 and 1,200 °C photodecomposed about 54 mol% of the MB in water (the corresponding τ ≈ 14.8 h) after exposing to 365-nm UV light for 12 h, the films prepared at 600 and 800 °C had smaller τ (≈9.0 h) and photodecomposed about 74 mol% of the MB in water at the same testing conditions.     

The Preparation and Characterization of La Doped TiO2 Nanotubes and Their Photocatalytic Activity

La-doped TiO₂ nanotubes (La/TiO₂ NTs) were prepared by the combination of sol-gel process with hydrothermal treatment. The prepared samples were characterized by using transmission electron microscopy, x-ray diffraction, x-ray photoelectron spectra, and ultraviolet-visible spectra. The photocatalytic performance of La/TiO₂ NTs was studied by testing the degradation rate of methyl orange under ultraviolet (UV) irradiation. The results indicated La/TiO₂ NTs calcined at 300°C consisted of anatase as the unique phase. The absorption spectra of the La/TiO₂ NTs showed a stronger absorption in the UV range and a slight red shift in the band gap transition than that of pure TiO₂ nanotubes. The photocatalytic performance of TiO₂ NTs could be improved by the doping of lanthanum ions, which is ascribed to several beneficial effects the formation of Ti-O-La bond and charge imbalance, existing of oxygen defects and Ti³⁺ species, stronger absorption in the UV range and a slight red shift in the band gap transition, as well as higher equilibrium dark adsorption of methyl orange. 0.75 wt% La/TiO₂ NTs had the best catalytic activity.     

Sol–gel preparation and characterization of Ag and Mg co-doped nano TiO<Subscript>2</Subscript>: efficient photocatalytic degradation of C.I. Acid Red 27

In this study, we successfully prepared pure, mono-doped, and Ag, Mg co-doped TiO₂ nanoparticles using the sol–gel method, with titanium tetraisopropoxide as the Ti source. The prepared samples were characterized by X-ray powder diffraction (XRD), specific surface area and porosity (BET and BJH) measurement, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, photoluminescence, and energy dispersive X-ray spectroscopy techniques. The XRD data showed that the prepared nanoparticles had the same crystals structures as the pure TiO₂. Also, DRS results indicated that the band gap of co-doped photocatalyst was smaller than that of the monometallic and undoped TiO₂ and that there was a shift in the absorption band towards the visible light region. Furthermore, the photocatalytic activity of the prepared catalysts was evaluated by the degradation of C.I. Acid Red 27 in aqueous solution under visible light irradiation. The results showed that Ag (0.08 mol%), Mg (0.2 mol%) co-doped TiO₂ had the highest photoactivity among all samples under visible light. It was concluded that co-doping of the Ag and Mg can significantly improve the photocatalytic activity of the prepared photocatalysts, due to the efficient inhibition of the recombination of photogenerated electron–hole pairs. The optimum calcination temperature and time were 450 °C and 3 h, respectively.     

Photocatalytic degradation of metoprolol in water suspension of TiO<Subscript>2</Subscript> nanopowders prepared using sol–gel route

Nanocrystalline titanium dioxide (TiO₂) powders have been synthesized by sol–gel method using titanium tetrachloride (TiCl₄) or tetrabutyl titanate (Ti(OC₄H₉)₄ as precursors, different alcohols and calcination temperatures in the range from 400 to 650 °C. The photocatalytic activity of as-prepared powders has been tested for the degradation of metoprolol tartrate salt, a selective β-blocker used to treat a variety of cardiovascular diseases, and compared to photocatalytic activity obtained from Degussa P25. Nanosized TiO₂ powders prepared from TiCl₄ and amyl-alcohol, calcined at 550 °C, displayed an activity comparable to Degussa P25, whereas the sample from the same series, calcined at 650 °C, showed higher photocatalytic activity in the whole range of the catalyst loading. Structural, morphological and surface properties of synthesized TiO₂ nanopowders have been investigated by XRD, SEM, EDS and BET measurements, as well as FTIR and Raman spectroscopy, in order to find out the material properties which enable rapid an efficient decomposition of metoprolol under UV radiation.     

High temperature stability and photocatalytic activity of nanocrystalline anatase powders with Zr and Si co-dopants

TiO₂ nanopowders doped by Si and Zr were prepared by sol–gel method. The effects of Si and Zr doping on the structural, optical, and photo-catalytic properties of titania nanopowders have been studied by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, and UV–Vis absorption spectroscopy. XRD results suggest that adding impurities has a significant effect on anatase phase stability, crystallinity, and particle size of TiO₂. Titania rutile phase formation in ternary system (Ti–Si–Zr) was inhibited by Zr⁴⁺ and Si⁴⁺ co-doped TiO₂ in high temperatures (500–900 °C) and 36 mol% anatase composition is retained even after calcination at 1,000 °C. The photocatalyst activity was evaluated by photocatalytic degradation kinetics of aqueous methylen orange under visible radiation. The results show that the photocatalytic activity of the 20 %Si and 15 %Zr co-doped TiO₂ nanopowders have a larger degradation efficiency than pure TiO₂ under visible light.     

Magnetic resonance study of annealed and rinsed N-doped TiO2 nanoparticles

Nanoparticles of nitrogen-modified TiO₂ (N-doped TiO₂) calcined at 300°C and 350°C, have been prepared with and without water rinsing. Samples were characterized by x-ray diffractrometry (XRD) and optical spectroscopy. The electron paramagnetic resonance (EPR) spectra from centers involving oxygen vacancies were recorded for all samples. These could be attributed to paramagnetic surface centers of the hole type, for example to paramagnetic oxygen radicals O^?, O₂ ^? etc. The concentration of these centers increased after water rising and it further increased for samples annealed at higher temperature. Additionally, for samples calcined at 300°C, and calcined at 350°C and rinsed, the EPR spectra evidenced the presence of magnetic clusters of Ti³⁺ ions. The photocatalytic activity of samples was studied towards phenol decomposition under unltraviolet-visible (UV-Vis) irradiation. It was found that, in comparison to the starting materials, the rinsed materials showed increased photocatalytic activity towards phenol oxidation. The light absorption (UV-Vis/DRS) as well as surface Fourier transform infrared/diffuse reflectance spectroscopy (FTIR/DR) studies confirmed a significantly enhanced light absorption and the presence of nitrogen groups on the photocatalysts surfaces, respectively. A significant increase of concentration of paramagnetic centers connected with oxygen vacancies after water rising has had an essential influence on increasing their photocatalytic activity.      

Investigations on the Phase Transformation,Optical Characteristics,and Photocatalytic Activity of Synthesized Heterostructured Nanoporous Bi2O3–TiO2

Fine‐powdered, heterostructured, nanoporous Bi₂O₃–TiO₂ (BTO) was synthesized by a green approach using ultrasonication, with the mole ratio Bi/Ti of 1:1 and calcined at different temperatures. The physical and optical properties of the mixed oxides were investigated. The phase structure, as identified by X‐ray diffraction (XRD), showed the appearance of new phases as a function of the calcination temperature. Morphological examinations indicated the formation of a nanoporous structure with a drastic change in morphology at the calcination temperature of 850°C from a globule to a rod‐shaped structure, which further got transformed to a rocky appearance at 1200°C. Doping with Bi₂O₃ led to the lowering of the bandgap of TiO₂ from 3.25 to 2.5 eV. A BTO nanocatalyst calcined at 450°C exhibited promising photocatalytic activity for the degradation of quinalphos (QP) (92%) after a time interval of 100 min under visible light and at the optimum pH 8. The kinetics of degradation of QP showed that it follows a pseudo‐first‐order path with a rate constant 0.01267 min^?1. The synthesized BTO mixed oxide showed profound improvement in photocatalytic activity in the visible region as compared to TiO₂.     

Fabrication and characterization of NiTiO3 nanofibers by sol–gel assisted electrospinning

Continuous NiTiO₃ nanofibers have been successfully synthesized by a sol–gel assisted electrospinning method followed by calcination at 600 °C in air. These nanofibers were characterized for the morphological, structural and optical properties by scanning electron microscopy (SEM), energy-dispersive X-ray spectrum (EDS), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV–visible (UV–vis) diffuse reflectance spectroscopy (DRS). SEM results reveal that the obtained NiTiO₃ nanofibers are 175 nm in diameter and several micrometers in length after annealing at 600 °C. The XRD analysis shows that the nanofibers possess highly crystalline structure with no impurity phase. In contrast, the NiTiO₃ nanoparticles synthesized at the identical conditions by a sol–gel route have impurities including TiO₂ and NiO. Moreover, the electrospun NiTiO₃ nanofibers are endowed with an obvious optical absorbance in the visible range, demonstrating they have visible light photoresponse.     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Photocatalytic degradation of organic compounds in aqueous systems by Fe and Ho codoped TiO<Subscript>2</Subscript>

Undoped, single-doped, and codoped TiO₂ nanoparticles were prepared by the sol-gel method and characterized with X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET)-specific surface area (S_BET), UV-Vis absorption spectra (UV-Vis), and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activity was evaluated by methyl orange (MO) degradation in an aqueous suspension under UV or simulated solar light illumination. XRD showed that all samples calcined at 600°C preserved the anatase structure, and doping inhibited the increase of crystallite size. The BET result revealed that doping improved the surface area of TiO₂. UV-Vis indicated that Fe³⁺-doping broadened the absorption profile of TiO₂. XPS demonstrated that doping was advantageous to absorb more surface hydroxyl groups or chemisorbed water molecules. Photocatalytic degradation showed that the photocatalytic activity of TiO₂ codoped with Fe³⁺ and Ho³⁺ ions was markedly improved. This was ascribed to the fact that there was a cooperative action in the two doped elements. Fe³⁺-doping broadens the absorption profile, improves photo utilization of TiO₂, and then generates more electronhole pairs. Ho³⁺-doping restrains the increase in grain size and retards the recombination of photo-generated electrons and holes.