Measurements of dispersion curves of leaky Lamb waves using a lensless line-focus transducer.

This paper presents a new method of measuring dispersion curves of leaky Lamb waves propagating in a thin plate. The measurement system is based on a lens-less line-focus transducer and its defocusing measurement technique. A new waveform processing method known as V(f, z) method is introduced for analyzing the measured waveforms and for extracting the dispersion relation. For two thin-plate samples, namely a 150 microm thick alumina plate and a 320 microm thick stainless steel plate, the dispersion curves of several lower order modes of leaky Lamb waves have been experimentally determined in the frequency range of few to 25 MHz. The experimental dispersion curves have then been compared with the theoretical ones. Excellent agreement is observed. It is then verify that this method indeed provides a convenient and accurate way for experimentally measuring dispersion curves of leaky Lamb waves of thin-plate samples.     

铝板中Lamb波检测的实验研究

Lamb波在传播过程中具有频散及多模态特性,若相关参数选择不当,会导致在实际应用中信号相互叠加而无法识别。本文基于Lamb波的频散曲线是其频散方程实数解分布的特点,采用二分法绘制了铝板中Lamb波的频散曲线、波结构曲线和入射角曲线。根据曲线选择S0模态的Lamb波对1mm厚铝板中不同类型的缺陷进行检测。实验结果表明,S0模态的Lamb波对裂纹型缺陷和贯穿型缺陷十分敏感,但对于裂纹型缺陷,其幅值变化并不与缺陷大小成线性关系,并且S0模态Lamb波的声场指向性十分集中,在偏离声束轴线时无法检测到缺陷。     

Propagation of guided elastic waves in 2D phononic crystals

The phononic band structure of two-dimensional phononic guides is numerically studied. A plane wave expansion method is used to calculate the dispersion relations of guided elastic waves in these periodic media, including 2D phononic plates and thin layered periodic arrangements. We show that, for any guided elastic wave, Lamb or generalised Lamb modes, stop bands appear in the dispersion curves, displaying a phononic band structure in both cases.     

Wideband dispersion removal and mode separation of Lamb waves based on two-component laser interferometer measurement

Ultrasonic Lamb waves are considered as a sensitive and effective tool for nondestructive testing and evaluation of plate-like or pipe-like structures. The nature of multimode and dispersion causes the wave packets to spread, and the modes overlap in both time and frequency domains as they propagate through the structures. By using a two-component laser interferometer technique, in combination with a priori knowledge of the dispersion characteristics and wave structure information of Lamb wave modes, a two-component signal processing technique is presented for implementing dispersion removal and mode separation simultaneously for two modes mixture signals of Lamb waves. The proposed algorithm is first processed and verified using synthetic Lamb wave signals. Then, the two-component displacements test experiment is conducted using different aluminum plate samples. Moreover, we confirm the effectiveness and robustness of this method.     

Prolonged acousto-optic interaction with Lamb waves in crystalline plates

The propagation and acousto-optic interaction of Lamb modes in an anisotropic plate of tellurium dioxide (TeO2) are studied numerically and analytically. In the case of a Y-cut X-propagating TeO2 plate, the very high elastic anisotropy of the crystal greatly modifies the dispersion curves, giving rise to their multiple oscillations. The existence ranges of backward Lamb modes increase with the mode order contrary to the case of isotropic plates. The quasi-collinear light scattering by Lamb waves is considered. Owing to the structure of Lamb wave field, a simultaneous light diffraction at two different optical frequencies can take place while Lamb waves are excited only at the single frequency. It is demonstrated with the Z-cut (110)-propagating plate that a small change in the acoustic frequency can result in a significant shift in the frequency of the scattered light.     

板状结构Lamb波频散补偿与聚焦接收成像检测

对板状结构中Lamb波的频散和多模现象进行了理论分析,采用有限元仿真方法获取了Lamb波与缺陷作用后的回波信号,对信号进行聚焦接收处理,即在一定距离范围内利用导波频散特性对各个模式信号进行频散补偿,提取补偿后信号的幅值,结果表明当所得信号幅值最大时,所对应的补偿距离等于缺陷与换能器之间的实际距离.利用这一结论,提出了以...     

矩形截面固体波导中弹性导波模式的板波叠加解

参照板中兰姆波模式的子波叠加解求解了矩形截面固体波导中弹性导波的模式。其中子波设定为横向满足自由边界反射条件、纵向波数分量相同的各板波模式。假设声场的完备性,利用子波模式的正交性,结合矩形截面的几何对称性可以得到4组独立导波特征方程用于频散曲线以及导波模式计算,其计算结果与有限元法计算结果相符。研究以解析模型表明:矩形截面固体波导中的导波是其内部以一定纵向波数分量斜向传播的板波模式在两个自由侧面上经过反复反射与模式转化后,横向耦合谐振而形成的。      

Guided waves in elastic rectangular bars:A solution using partial plate mode decomposition

Similar to Auld's solution for Lamb waves,the wave modes in elastic rectangular bar are solved by partial wave decomposition method.The partial waves are composed of plate modes with the same wavenumber component in waveguide longitudinal direction,thus free boundary conditions on one pair of opposite surfaces are automatically satisfied.Based on completeness assumption and orthogonality of the plate modes,four independent eigenequations are eventually derived for dispersion curve and mode shape investigation.Numerical evaluation shows the calculated results are in consistent with the FEM results.It is then verified that the plate modes which obliquely bounced back and forth between the two opposite surfaces compose the guided modes traveling in the rectangular waveguides with certain wave numbers in transversely resonant cases.     

Guided wave propagation and mode differentiation in hollow cylinders with viscoelastic coatings

Guided wave propagation theories have been widely explored for about one century. Earlier theories on single-layer elastic hollow cylinders have been very beneficial for practical nondestructive testing on piping and tubing systems. Guided wave flexural (nonaxisymmetric) modes in cylinders can be generated by a partial source loading or any nonaxisymmetric discontinuity. They are especially important for guided wave mode control and defect analysis. Previous investigations on guided wave propagation in multilayered hollow cylindrical structures mostly concentrate on the axisymmetric wave mode characteristics. In this paper, the problem of guided wave propagation in free hollow cylinders with viscoelastic coatings is solved by a semianalytical finite element (SAFE) method. Guided wave dispersion curves and attenuation characteristics for both axisymmetric and flexural modes are presented. Due to the fact that dispersion curve modes obtained from SAFE calculations are difficult to differentiate from each other, a mode sorting method is established to distinguish modes by their orthogonality. Theoretical proof of the orthogonality between guided wave modes in a viscoelastic coated hollow cylinder is provided. Wave structures are also calculated and discussed in view of wave mechanics in multilayered cylindrical structures containing viscoelastic materials.     

非线性兰姆波在阶梯板中传播的有限元仿真

在非线性兰姆波检测中,累积二次谐波是重要的检测信号.该文利用有限元法仿真了非线性兰姆波在阶梯板中的产生和传播过程,通过二维离散傅里叶变换分析了兰姆波的传播模态和各个模态通过波导横截面的能流大小,给出了各个模态在阶梯板中的反射、透射系数,总结了其随阶梯板厚度的变化规律.研究发现,随着台阶增高,散射效应使得兰姆波更难入射波...     

Guided Waves in a Multi-Layered Cylindrical Elastic Solid Medium

We investigate the guided waves in a multi-layered cylindrical elastic solid medium. The dispersion function of guided waves is usually complex and the dispersion curves of all modes are not conveniently obtained. Here we present an effective method to obtain the dispersion curves of all modes. First, the dispersion function of the guided waves is transformed into a real function. The dispersion curves are then calculated for all the modes of the guided waves by the bisection method. The modes with the orders n = 0, 1, and 2 are analysed in two- and three-layer media. The existence condition of Stoneley wave is discussed. The modes of the guided waves are also investigated in a two-layer medium, in which the velocity of shear wave in the outer layer is less than that in the inner layer.     

两侧有固体层负载时板中Lamb波的传播

本文研究了薄板二面有固体导负载时板中Ｌａｍｂ波的传播，从弹性波理论出发并结合应的边界条件，导出板中Ｌａｍｂ波的色散方程，数值计算表示，不管作为自由状态时板中Ｌａｍｂ波相速（板厚取定时）是大于或小于外层固体的声表面波波速，板中对称及反对称模式的Ｌａｍｂ波相速都随着外层固体层厚度增加而变化并且渐近于外层固体的声表面波波速，数值计算又表明，对很薄的板，板中对称及反对称模式的相速均随负载板的厚度呈线性变化     

用于储罐底板缺陷检测的超声兰姆波模式研究

从超声兰姆波的声场方程出发,得到板材表面离面位移(法向位移)为零的条件,即当超声兰姆波的相速度等于板材介质的纵波声速时,在板材表面的离面位移为零。在给定适当频厚积的条件下,分别数值模拟了仅有切向位移而无离面位移的A1、S1、A2和S2兰姆波模式在有液体负载的单层钢板中的传播情形。结果表明:离面位移为零的S2模式频散较小且对板中缺陷更为敏感。     

套管井超声导波成像系统开发与工程应用研究*

针对现有套管井检测与评价技术存在的缺陷,开展了进一步的导波成像方法与技术开发研究。对套管壁A0导波模式频散与泄漏衰减特性,以及泄漏衰减特性与管外粘结材料特性阻抗的关系进行了分析。在此基础上进行了不同粘结载荷钢板模型A0模泄漏衰减等特性以及脉冲回波厚度共振波特性的实验测试。结果显示,结合A0模式的衰减与管外粘结材料特性阻抗的测试结果,可有效定征管外粘结材料特性,进一步确定和成像管外环形空间水力联通特性。以此为基础,开发了耐温和耐压宽带超声换能器,以及检测与成像系统。通过模型井和实际井的测试,获得良好效果。     

轨道板中超声兰姆波传播的有限元计算和实验*

该文针对我国高速铁路轨道板缺陷的非接触动态检测问题,研究了空气耦合超声兰姆波在轨道板中的传播规律。首先,给出了轨道板中超声兰姆波的相速度和群速度频散曲线,结果表明:随着频厚积的增加,频散现象越明显,并且A0相速度收敛于Rayleigh波的波速。然后,建立轨道板中波传播的有限元模型,计算得到兰姆波传播的群速度为2220 m/s,且二维傅里叶变换系数的较大值沿Rayleigh波的频散曲线分布。最后,在沪杭高铁嘉兴南站进行了现场测试,以8.8°倾斜角向轨道板激励产生超声兰姆波,激发产生的兰姆波模态群速度为2325 m/s,且二维傅里叶变换分析其系数的较大值沿Rayleigh波的频散曲线分布。有限元计算结果和实验结果均与理论计算结果一致。该研究为后续轨道板缺陷的非接触动态检测提供了理论依据和实验方法。     

Influence of the slow wave on the relation between the angular resonances and the leaky guided modes properties for a poroelastic plate embedded in water

A numerical study of the guided modes in a water-saturated poroelastic plate that obeys the Biot theory is presented. In the first part, we study the leaky guided modes and the angular resonances when the slow wave does not propagate. Two types of guided modes exist. The first ones occur from coupling of the fast longitudinal wave with the shear wave; most of them propagate whatever the frequency is, provided that it is not close to their cut-off frequencies. The leaky guided modes of the second type occur from coupling of the two longitudinal waves and the shear wave. These modes do not propagate (they are highly damped) as long as the slow wave remains diffusive. We show that the characteristics of the angular resonances can be linked to the leaky guided waves of the first type in the same way as for an elastic plate. The guided modes of the second type may not be associated to angular resonances. In the second part, we consider a thinner plate in a higher frequency range so that the slow wave can propagate. Once again its influence is studied both on the leaky guided modes and on the angular resonances.     

兰姆波检测信号的匹配追踪时频分析

为有效去除兰姆波检测信号中的冗余信息和识别多个模态,应用匹配追踪方法对兰姆波信号进行处理。在Chirplet原子基础上添加弯曲算子进行改进,以更好地匹配频散和多模式兰姆波信号的特征。由改进的Chirplet原子组成过完备字典,使用基于遗传算法的匹配追踪(GAMP)信号稀疏分解方法,从过完备字典中选出与待分析信号相匹配的最佳原子,利用最佳匹配原子和对应的分解系数进行信号重构和时频分析。研究结果表明,改进后的Chirplet原子更能反映出兰姆波信号的非线性时频变化特征,得到的时频分布与频散曲线的弯曲特性能很好的吻合。采用改进后的Chirplet原子匹配追踪方法可以获取更加精确的走时信息,为后续兰姆波损伤定位成像奠定基础。      

Localization of notches with Lamb waves

A time-frequency representation (TFR) is used to analyze the interaction of a multimode and dispersive Lamb wave with a notch, and then serves as the basis for a correlation technique to locate the notch. The experimental procedure uses a laser source and a dual-probe laser interferometer to generate and detect Lamb waves in a notched plate. The high fidelity, broad-bandwidth, point-like and noncontact nature of laser ultrasonics are critical to the success of this study, making it possible to experimentally measure transient Lamb waves without any frequency biases. A specific TFR, the reassigned spectrogram, is used to resolve the dispersion curves of the individual modes of the plate, and then the slowness-frequency representation (SFR) of the plate is calculated from this reassigned spectrogram. By considering the notch to be an additional (second) source, the reflected and transmitted contributions of each Lamb mode are automatically identified using the SFRs. These results are then used to develop a quantitative understanding of the interaction of an incident Lamb wave with a notch, helping to identify mode conversion. Finally, two complementary, automated localization techniques are developed based on this understanding of scattering of Lamb waves.     

The band gaps of Lamb waves in a ribbed plate: A semi-analytical calculation approach

In this paper a semi-analytical method is proposed to investigate the transmission band gaps of Lamb waves through repetitive structures in a waveguide. For a unit cell the scattering matrix is obtained by the Lamb mode matching technique at each artificially sliced interface and then substituted into the Bloch theorem to solve the eigenproblem incurred by cell repetition. The method is implemented on a ribbed plate. The band gaps in the dispersion curves are confirmed by the dips of Lamb wave transmission coefficients, and attributed to the coupled vibrations of Lamb modes in different sliced sections of the unit cell.     

采用单个压电传感器的单模式兰姆波激发频率的选择

考虑了压电传感器(PZT)与板之间的耦合作用,从理论上研究了单个压电传感器激发时产生单模式兰姆波的频率调节方法,实验给出了模式选择在兰姆波结构健康监测中的应用. 在板材、板厚以及PZT尺寸一定的情况下,从理论上能够预测到作为频率函数的各兰姆波模式的幅值变化. 根据某特定兰姆波模式的幅值最大而其他模式幅值相对最小时所对应的频率,即可识别出该兰姆波模式优化的激发频率. 数值仿真验证了理论的有效性以及单模式兰姆波选择的可能性. 在不同的激发频率下,分别激发了优化的A0 模式,优化的S0模式以及共存的A0和S0模 关键词： 兰姆波 压电传感器 激发频率 结构健康监测