Evaluation of Immobilization Techniques for the Fabrication of Nanomaterial-Based Amperometric Glucose Biosensors

Eleven glucose biosensors were prepared by cross-linking, entrapment, and layer-by-layer assembly to investigate the influence of these immobilization methods on performance. The effects of separate nanozeolites combined with magnetic nanoparticles and multiwalled carbon nanotubes in the enzyme composition on the performance of glucose biosensors were compared. Cyclic voltammetric studies were carried out on the biosensors. Acrylonitrile copolymer/nanozeolite/carbon nanotube and acrylonitrile copolymer/nanozeolite/magnetic nanoparticle electrodes prepared by a cross-linking method showed the highest electroactivity. These results indicated that a synergistic effect occurred when multiwalled carbon nanotubes, magnetic nanoparticles, and nanozeolites were combined that greatly improved the electron transfer ability of the sensors. Amperometric measurements by the glucose oxidase electrodes were obtained that showed that the acrylonitrile copolymer/nanozeolite/carbon nanotube electrode was the most sensitive (10.959 microamperes per millimolar). The lowest detection limit for this biosensor was 0.02 millimolar glucose, with a linear dynamic range up to 3 millimolar. The response after thirty days was 81 percent of the initial current.     

纳米沸石修饰微通道反应器内固定化酶催化的水解反应动力学

通过在毛细管内层叠层组装纳米沸石并固定脂肪酶来构建纳米沸石修饰的固定化酶微反应器通道,将纳米沸石良好的生物相容性和高的酶固定能力与微反应器反应效率高、扩散传质快等优点相结合. 以对硝基苯棕榈酸酯的水解作为探针反应对该微反应器内固定化酶催化水解反应动力学进行了研究和计算,并与普通反应器内同样的反应进行比较. 通过对比米氏方程参数,证实在微反应器内酶催化水解反应效率可比普通反应器内提高3倍以上并可提高酶和反应底物的亲和能力.     

层叠层技术组装纳米沸石——沸石涂饰纤维和沸石空 心纤维

以纳米沸石为基元构件,通过层(layer-by-layer)组装技术在碳纤维模板上成功制备了纳米沸石涂饰纤维(zeolitecoatedfibers),焙烧除去碳纤维模板后,制微了完整的沸石空心纤维(hollowzeolitefibers),并系统研究了它们的制备条件和材料结构。发现纳米沸石胶体溶液的pH值是制备沸石涂饰纤维和空心沸石纤维的关键因素,其它条件,诸如吸附液的离子强度,每层吸附后的干燥以及每次干燥前是否用PDDA溶液预浸泡,对纤维的完美性也有影响。通过改变吸附纳米沸石的类型和层数可能调变沸石层的组成和厚度,而交替吸附不同的纳米沸石可能制备复合沸石涂饰纤维及复合空心沸石纤维。     

Controlled nanozeolite-assembled electrode: remarkable enzyme-immobilization ability and high sensitivity as biosensor

An enzyme-immobilized nanozeolite-assembled electrode was prepared by controlled assembly of nanometer-sized Linder type-L zeolite (nano-LTL-zeolite) on an indium tin oxide (ITO) glass electrode surface, and subsequent immobilization of cytochrome c. Cyclic voltammetric (CV) and amperometric experiments showed that, relative to other reported electrodes, the enzyme-immobilized electrodes possess fast electron-transfer rates (2.2 s(-1)), a broad linear range (15-540 micromol L(-1)), a low detection limit (3.2 nmol L(-1)), a remarkably long lifetime (5 months), and high stability in the pH range 5-10. These characteristics could be due to the fact that nanozeolites assembled on ITO have high immobilization ability and facilitate interaction with enzymes. The function controllability of these enzyme electrodes, resulting from the facile manipulability of nanozeolite-assembled layers, may provide a possibility to rationally design biosensors.     

LAYER-BY-LAYER ASSEMBLY OF NANOZEOLITE BASED ON POLYMERIC MICROSPHERE: ZEOLITE COATED SPHERE AND HOLLOW ZEOLITE SPHERE

ABSTRACT

Zeolite β, silicalite-1, ZSM-5, and TS-1 coated spheres have been prepared successfully through layer-by-layer assembly of nanozeolite/polymer multilayers on polystyrene (PS) microspheres, and hollow zeolite spheres have been obtained by removal of the core by calcination. In the adsorption process of nanozeolites onto the polyelectrolyte-modified template spheres, it has been found that zeta potential of the zeolite colloidal solution that determines the electrostatic interaction has important effects on the zeolite adsorption procedure. The charge on the original sphere template is not necessary, because proper polyelectrolyte modification could change the surface property of the template and make it suitable for layer-by-layer adsorption. The influences of zeolite type and/or size (40–120 nm), the number of zeolite/poly(diallyl-dimethyl-ammonium) layer pairs, and the template sphere size (0.53–10.3 µm) on the preparation of the hollow zeolite spheres were also discussed.     

Preparation and Characterization of Microwave-absorption of Sarulla North Sumatra Zeolite and Ferric Oxide-filled Polyurethane Nanocomposites

Microwave-absorptive polymeric composite materials are becoming important to protect interference of any communication systems due to the increase in the use of microwave-inducing devices. In this work, the microwave-absorptive polyurethane composites are prepared using natural zeolites of Sarulla North Sumatra and commercial ferric-oxide as fillers. Weight ratio of the natural zeolite to ferric oxide were varied (18:2; 16:4; 14:6; 12:8 and 10:10) by weight. The fillers are prepared using ball milling technique and characterized using Particle Size Analyzer for particle size distribution. The nanocomposites, prepared using in-situ reaction of polyethylene glycol and toluene diisocyanate, is characterized for physical and mechanical properties using tensile strength, thermal properties with TGA techniques, as well as morphological and chemical properties using scanning electron microscopy. Composition and loading of the nanofillers against polyurethane matrices is 20% by weight. Microwave-absorption properties of the nanocomposites is characterized using 8-12 GHz frequency. Tensile strengths of the natural zeolite-ferric oxides polyurethane nanocomposites shows higher values when matrices filled with lower ferric-oxide, which could be due to the nanozeolites have functioned as reinforcement for the polyurethane matrix through polar-polar interaction between the filler surfaces with the matrices. The microwave absorption properties, which investigated by Vector Network Analyzer, of the nanocomposites filled in polyurethane with the ratio of nanozeolite to ferric oxide filler of 12:8 shows reflection loss of – 13.2 dB. This condition was observed at 11.1 GHz.     

纳米多级孔分子筛：简短的综述

分子筛是一种三维微孔结构的硅铝酸盐晶体,具有灵活多变的骨架和组成、较高的物理和水热稳定性、无毒、高比表面积、离子可交换性以及很低的成本等特点,因而在油品精制、石油化学、农业、水和污水处理等众多领域中用作离子交换剂、催化剂和吸附剂。尽管分子筛的应用是基于其本身的微孔结构,但微孔也导致体积较大的反应物和产物分子的传质阻力高。通过制备纳米尺度和多级孔结构的分子筛等多种手段可克服常规分子筛所具有的传质限制。人们已经开发了多种方法制备了新型的分子筛材料,并考察了它们在各种催化反应和吸附反应中的性能。在反应体系中采用这种多级孔的纳米分子筛,有可能提高催化剂的使用寿命和催化性能,抑制积碳和失活。本综述概述了多级孔分子筛和纳米分子筛的高性能及其合成方法的最新进展,讨论了每个合成方法的优缺点,简述了纳米分子筛和二级孔结构分子筛的催化应用,并与常规分子筛进行了比较。     

(1)H relaxivity of water in aqueous suspensions of Gd(3+)-loaded NaY nanozeolites and AlTUD-1 mesoporous material: the influence of Si/Al ratio and pore size

The results of a (1)H nuclear magnetic relaxation dispersion (NMRD) and EPR study on aqueous suspensions of Gd(3+)-loaded NaY nanozeolites and AlTUD-1 mesoporous material are described. Upon increase of the Si/Al ratio from 1.7 to 4.0 in the Gd(3+)-loaded zeolites, the relaxation rate per mM Gd(3+) (r1) at 40 MHz and 25 degrees C increases from 14 to 27 s(-)1 mM(-1). The NMRD and EPR data were fitted with a previously developed two-step model that considers the system as a concentrated aqueous solution of Gd(3+) in the interior of the zeolite that is in exchange with the bulk water outside the zeolite. The results show that the observed increase in relaxivity can mainly be attributed to the residence lifetime of the water protons in the interior of the material, which decreased from 0.3 to 0.2 micros, upon the increase of the Si/Al ratio. This can be explained by the decreased interaction of water with the zeolite walls as a result of the increased hydrophobicity. The importance of the exchange rate of water between the inside and the outside of the material was further demonstrated by the relatively high relaxivity (33 s(-1) mM(-1) at 40 MHz, 25 degrees C) observed for a suspension of the Gd(3+)-loaded mesoporous material AlTUD-1. Unfortunately, Gd(3+) leaches rather easily from that material, but not from the Gd(3+)-loaded NaY zeolites, which may have potential as contrast agents for magnetic resonance imaging.     

Preparation and properties of polyurethane networks based on α,ω-difunctional poly(hexafluoropropylene oxide)

Poly(hexafluoropropylene oxide), poly(HFPO), networks were prepared from functional polymers by end linking via urethane groups. The prepolymers were characterized by NMR spectroscopy and GPC. The networks were characterized by determination of the number of network chains from the shear modulus, and were snown to contain both trifunctional crosslinks and difunctional links. The properties of the networks were investigated by a range of techniques. Compared with fully-fluorinated networks formed via triazine cross-links, investigated previously, the urethane-linked networks were more readily prepared but were poorer elastomers, were less thermally stable, and were less resistant to swelling by common polar solvents. © 1995 John Wiley & Sons, Inc.     

膜催化研究II. 多孔无要膜的制备与表征及其反应器对甲醇脱氢反应的促进作用

采用溶胶-凝胶法制备了多孔氧化铝膜, 并通过DSC、TGA、SEM、N~2吸附和气体透过率测定等手段, 对膜的性能进行了表征。结果表明, 用这种方法制备的多孔氧化铝膜是一种均匀无裂痕和具有较窄孔径分布(约4nm)的膜材料。将此多孔氧化铝膜制成膜反应器后, 用于甲醇催化脱氢制甲醛的反应, 发现甲醇转化率比常规反应器有较大幅度的提高。同时首次尝试采用溶胶-凝胶法将催化活性组分直接负载到多孔氧化铝膜上, 从而得到了一种具有催化活性的多孔膜, 并考察了它的反应活性。文中对由这两种多孔膜及钯/陶瓷复合膜制成的反应器的特点进行了比较。     

南瓜籽烘烤前后化学成分的分析

对烘烤前后南瓜籽中的化学成分进行分析并对比。采用同时蒸馏萃取装置萃取南瓜籽中的挥发性成分,采取超临界CO2萃取技术萃取南瓜籽油脂,并将其分为酸、碱、中性三个部分,用气相色谱-质谱联用方法分析其中化学成分并进行对比。结果表明,南瓜籽挥发性成分中含有多种醛类和酯类化合物,烘烤后产生了大量的烷基吡嗪,其在碱性部分中的相对含量比烘烤前提高14倍多,不饱和醛类化合物含量也有明显提高。南瓜籽油脂中的主要化学成分是油酸、亚油酸及其酯类。还含有生物活性功能成分如植物甾醇、角鲨烯和维生素E等。烘烤后除角鲨烯含量有所降低,维生素E、植物甾醇、亚麻酸等均有提高。     

IClO2异构化反应机理及电子密度拓扑研究

利用密度泛函理论方法研究了IClO2异构化反应机理. 优化得到了七种异构体, 其中OIClO和IClOO还未见报道, 对各异构体的热力学稳定性进行了比较. 找到了异构化过程的过渡态, 并通过内禀反应坐标(IRC)计算确认了各个异构体之间的相互转化关系. 从量子拓扑学的角度, 对典型异构化反应通道IRC途径上的各点进行了电子密度拓扑分析, 讨论了反应过程中化学键的断裂、生成以及化学键的变化规律, 找到了反应途径上的能量过渡态(ETS)和结构过渡态(STS).     

Reversed-phase high-performance liquid chromatographic, gel electrophoretic and size exclusion chromatographic studies of subunit structure of arachin and its molecular species

Arachin and its molecular species (arachin I and arachin II) were separated and isolated. The number and kind of subunits of arachin, arachin I and arachin II were determined. Studies were carried out under different experimental conditions using slab gel electrophoresis, size-exclusion chromatography and reversed-phase high-performance liquid chromatography. Gel electrophoresis was done under varying concentrations of resolving gel. Tube gel as well as slab gel electrophoresis were used and continuous as well as discontinuous buffer systems were used for both types of electrophoresis. In addition, the subunits were separated by reversed-phase HPLC using a gradient program. Arachin and arachin II were found to have 12 subunits each while arachin I showed six subunits. The subunits of arachin I were allowed to reconstitute by removing SDS. Eight combinations were tried for studying the reconstitution pattern. Molecular weight and weight ratio in each case were also determined.     

云南菊科中草药中铅含量特征分析

论述了云南２７种菊科中草药及其水提取物中铅含量的特征。菊科植物及水提物中铅含量的频数分布为正偏态,两者的相关系数ｒ＝０．０９,未呈现显著的线性相关。提取率较高的山紫苑、佩兰、木香铅实际含量低;铅含量高的叶下花、狭叶兔耳风、臭灵丹提取率又较低,减少了人体对Ｐｂ的过量摄入。     

GC-MS方法分析杨梅果实精油中香气成分

采用气相色谱一质谱联用技术分析鉴定了木叶、东魁及黑炭3种新鲜杨梅果实精油样品的化学成分,并对三者成分进行对比分析.木叶梅果实精油中鉴定出55个化合物,以单萜类成分为主;东魁梅果精油中鉴定出49个化合物,以倍半萜烯和烷烃类成分为主;黑炭梅果精油中鉴定出化合物48种,以倍半萜烯和烷烃类成分为主.木叶杨梅中富含单萜而缺少倍半萜烯,这可能是其香气浓且易腐烂原因.     

Manipulation of protein fingerprints during on-column fluorescent labeling: protein fingerprinting of six Staphylococcus species by capillary electrophoresis

Bacterial proteomes were analyzed by use of electrophoretically mediated microanalysis (EMMA) and field-enhanced stacking. A water-soluble protein fraction was injected onto a capillary. Next, a fluorogenic reagent was injected and allowed to react with the protein mixture, producing fluorescent products that were separated by submicellar capillary electrophoresis and detected by laser-induced fluorescence. By use of a low-ionic strength sample buffer and a brief electrophoretic step, slow moving anionic proteins were stacked at the reagent-sample interface and were preferentially labeled. By reversing the order of sample injection and labeling reagent, fast moving cationic proteins were preferentially labeled. By adjustment of the sample buffer pH, proteins with different isoelectric points were selectively labeled. Electrophoresis fingerprints were generated for the water-soluble protein fraction from six Staphylococcus species. The protein patterns produced were species-specific and were used to construct a phylogenetic tree.     

碳苷研究 V: 用Grignard试剂合成取代苯酚中酚羟基的保护及脱保护

本文报道了一些取代苯酚的合成, 并探讨了用Grignard试剂合成取代苯酚中酚羟基的保护及脱保护的问题. 利用苄基和甲基作为酚羟基的保护基, 对文献报道的切断醚键脱保护方法进行了评价. 找到了两种新体系能在更温和条件下切断醚键的方法, 指出了它们的适用条件. 实验结果符合硬软酸碱理论.     

电感耦合等离子体质谱(ICP-MS)法测定玻纤滤筒中金属元素本底值的预处理方法探讨

探讨了不同预处理方法对国产玻纤滤筒本底值的降低效果,便于废气样品的分析测定。分别对空白滤筒、热硝酸、硝酸+硫酸和硝酸+EDTA、HCl处理后的滤筒进行分析,测得滤筒中金属元素的含量;对处理效果较好的一批滤筒进行空白加标,考察加标回收率,全程用电感耦合等离子体质谱(ICPMS)法对样品进行测定,结果发现空白滤筒中部分金属元素含量较高;热硝酸处理后,滤筒本底中铅含量有所降低,但其它元素去除效果不显著;硝酸+硫酸处理后,滤筒中铅含量剧增;硝酸+EDTA处理滤筒,铅可以得到较好的去除效果,大部分金属元素含量有了明显降低;基于HCl对金属有较好的溶出效果,浸泡可较好地降低滤筒中金属元素的含量,但大量氯离子存在对ICP-MS法测定的干扰较大。对硝酸+EDTA处理后的滤筒进行空白加标,大部分金属元素加标回收率75%。故以硝酸+EDTA处理玻纤滤筒可以使国产玻纤滤筒适用于废气样品的分析。     

Terpenic and phenolic glycosides from leaves of Breynia officinalis HEMSL

From the leaves of Breynia officinalis, collected on Okinawa Island, six terpenic glucosides and six phenolic glycosides were isolated. Two of the terpenic glucosides were found to be known, and they were identified as turpinionoside B and betulalbuside A. The structures of the remaining terpenic glucosides were elucidated to be megastigmane glucosides, named breyniaionosides A-D, using spectroscopic analyses. The absolute structure of breyniaionoside D was determined using the modifed Mosher's method. The absolute structure of the known compound betulalbuside A was determined for the first time in this study. Six phenolic glycosides were found to be arbutin and its derivatives. Two known compounds were found to be robustaside A and eximine. New compounds were named isorobustaside A, and breyniosides A and B, and their structures were elucidated from spectroscopic evidence.     

玩具、铅笔中可溶性砷、锑、硒的形态分析

对玩具、铅笔中可溶性砷、锑、硒的形态分析方法进行了研究,对原子荧光光谱法测定不同价态砷、锑、硒的方法进行了优化,建立了砷、锑、硒的原子荧光光谱形态分析方法。该方法样品加标回收率为82.0%~110.0%,测定结果的相对标准偏差为1.35%~2.22%(n=10)。