聚乙烯醇对锌镉铅溶出增敏作用及应用

在０．０５ｍｏｌ／Ｌ（ｐＨ６．５）乙二妥－盐酸介质中,聚乙烯醇－１２４ＰＶＡ－１２４）对锌,镉,铅的电位溶出有显著的增敏作用。当富集６０ｓ时,其检出限均达６．０μｇ／Ｌ,线性范围：锌０．６－３５μｇ／Ｌ,镉０．６－４５μｇ／Ｌ,铅０．６－５０μｇ／Ｌ。标准加入回收率为９２．４％－１１０％。ＲＳＤ（ｎ－４）〈７．０％。     

催化动力学光度法测定痕量苯酚

研究了在硫酸介质中苯酚对Ｉ＾－１催化Ｃｅ＾４＋－Ａｓ（Ⅲ）反应的抑制作用及其动力学条件。建立了用催化动力这光度法测定痕量苯酚的新方法，结果表明，在０．００１ｍｏｌ／ＬＣｅ（ＳＯ４）２，０．００１２５ｍｏｌ／Ｌ，Ａｓ２Ｏ３，０．０１ｍｇ／Ｌ，ＫＩ，０．０１２５ｍｏｌ／Ｌ，Ｈ２ＳＯ４和０．１３％（ｗ／ｖ）ＮａＣｌ溶液中测定苯酚，其表面摩尔吸光系数为２．１×１０＾５Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，线性范围     

焙烧富集分离—氢化物原子荧光法测定地质物料中痕量硒

本文研究了一种焙烧富集分离，氢化物－原子荧光法测定地质物料中痕量Ｓｅ方法。系统地了Ｓｅ富集分离条件，考查了３０多种元素在焙烧前后对测定Ｓｅ的影响。在选定的最佳实验条件下，方法检出下限为０．０１μｇ／ｇ和０．０８９μｇ／ｇ，线性范围０．００１－０．３μｇ／ｍＬ。样品中Ｓｅ含量水平为０．０３６μｇ／ｇ和０．０８９μｇ／ｇ时的测量精度（ＲＳＤ）分别为１０％和５．８％。加标回收率为９７－９９％。采用本方法     

硒（IV）—四乙基碘化铵—砷（Ⅲ）体系的极谱吸附波及其应用

报道了一个测定硒的高灵敏极谱吸附波新体系。在０．７ｍｏｌ／Ｌ ＨＢｒ溶液中，Ｓｅ（Ⅳ）－（Ｃ２Ｈ５）４ＮＩ－Ａｓ（Ⅲ）体系于－０．６１Ｖ（ｖｓ．ＳＣＥ）处产生一高灵敏的极谱吸附波。峰电流与Ｓｅ（Ⅳ）浓度在０．１￣４０μｇ／Ｌ范围内呈线性关系。检出限为０．０５μｇ／Ｌ。研究了极谱波的性质。用本法测定了土壤中的全硒和有效硒，结果满意。     

烟草中Fe,Co一阶导数分光光度法同时测定的研究

本文研究了在ｐＨ４．０时，ｍｅｓｏ－四（４－磺酸基苯基）卟啉与铁、钴同时络合显色的反应条件以及一阶导数光谱行为。此体系一阶导数的灵敏度比零阶导数灵敏度高。Ｆｅ￣（３＋）～０．１８μｇ／ｍＬ、Ｃｏ￣（２＋）０～０．２４μｇ／ｍｌ，范围内符合比耳定律；检测限为：Ｆｅ￣（３＋）＝０．４８ｎｇ／ｍＬ，Ｃｏ￣（２＋）＝０．２ｎｇ／ｍＬ。回收率为：Ｆｅ９８．５％～１００．８％，Ｃｏ９９．２％～１０１．３％。此方法用于烟草中痕量Ｆｅ、Ｃｏ测定，与ＡＡＳ值相比较，结果令人满意。     

硒（Ⅳ）—碘酸钾体系极谱法测定痕量亚硫酸根

报道了一种单扫描极谱测定痕量亚硫酸根的方法。在高氯酸介质中，亚硫酸根可将Ｓｅ（Ⅳ）还原为Ｓｅ（０），在ＰＨ１０．５的ＮＨ３－ＮＨ４Ｃｌ缓冲溶液中，在碘酸钾存在下，于－０．９０Ｖ（ｖｓ．ＳＣＥ）处产生一个灵敏的还原催化波，导数波高与亚硫酸根浓度在０－０．４ｍｇ／Ｌ范围内有线性关系，检出限为２μｇ／Ｌ。     

火焰原子吸收光谱法间接测定非金属材料中氯

报道了火焰原子吸收光谱法（ＦＡＡＳ）间接测定非金属材料中氯的方法，采用ＡｇＣｌ沉淀，测定剩余Ａｇ~＋间接求出氯含量。方法的特征浓度为０．０１４ｍｇ／Ｌ（１％吸收），检出限为０．０３２ｍｇ／Ｌ（３），测定下限为０．１１ｍｇ／Ｌ，相对标准偏差（ＲＳＤ）为１．５％～１０％，样品加标准回收率在９１．４％－１０５％之间。     

丁基罗丹明B—钼酸盐光度法连续测定铈和钪

在聚乙烯醇（ＰＶＡ）存在下，丁基罗丹明Ｂ（ＢＲＢ）分别与铈钼、钪钼杂多酸络阴离子形成离子缔合物，其最大吸收均位于５７０ｎｍ，表面摩尔吸光度分别为εＣｅ＝３．９６×１０＾６Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，εＳｃ＝４．７１×１０＾５Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，服从比耳定律范围分别为０－２４μｇ／Ｌ Ｃｅ和０－６０μｇ／ＬＳｃ，测定极限为Ｃｅ１．０μｇ／Ｌ（ｎ＝１２）和Ｓｃ１．９μｇ／Ｌ（ｎ＝１０），对     

氢化物发生原子荧光光谱法测定临床样品微量砷和硒

研究了氢化物原子荧光法测定临床床样品全血，血清，胎盘，头发，指甲和尿液中微量Ａｓ和Ｓｅ的方法。线性范围为Ａｓ１．３＊１０＾－９－２．５＊１０＾－７ｇ／ｍＬ，Ｓｅ２．８＊１０＾１０－７．５＊１０＾－８ｇ／ｍＬ；相对标准偏差（ｎ＝１３）Ａｓ２．６－３．６％，Ｓｅ２．８－４．２％；Ａｓ、Ｓｅ的标准加入回收率为９６．７－１０４．２％，用于６种临床样品中Ａｓ、Ｓｅ测定，获得满意的结果。     

在线流动注射螯合树脂预富集石英缝管增敏火焰原子吸收法测定水中痕量铅

应用高效的在线流动注射螯合树脂预富集石英缝管增敏火焰原子吸收系统直接测定水呈痕量铅。实验用内装２００ｍｇＡｍｂｅｒｌｉｔｅＸＡＤ－４键合的５－磺酸－８羟基喹啉螯合树脂的锥形柱,在ＰＨ９条件下样品流速为８．０ｍＬ／ｍｉｎ,９０ｓ采样,用０．５ｍｏｌ／Ｌ Ｈｃｌ洗脱,在分析速度为３０样／ｈ,获得３６倍的富集,经石英缝管增敏,灵敏度提高达１１５倍,线性范围为０－２００μｇ／Ｌ,检出限为１μｇ／Ｌ。铅含量水平５０μｇ／Ｌ的水样连续测定１１次的相对标准偏差２．５％,可直接测定水体中μｇ／Ｌ级的铅。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.