Desulfurization kinetics of ZnO sorbent loaded on semi-coke support for hot coal gas

Zn-based sorbent (Z20SC) prepared through semi-coke support in 20 wt% zinc nitrate solution by high-pressure impregnation presents an excellent desulfurization capacity in hot coal gas,in which H2 S can not be nearly detected in the outlet gas before 20 h breakthrough time.The effects of the main operational conditions and the particle size of Z20SC sorbent on its desulfurization performances sorbent were investigated in a fixed-bed reactor and the desulfurization kinetics of Z20SC sorbent removing H2 S from hot coal gas was calculated based on experimental data.Results showed that the conversion of Z20SC sorbent desulfurization reaction increased with the decrease of the particle size of the sorbent and the increases of gas volumetric flow rate,reaction temperature and H 2 S content in inlet gas.Z20SC sorbent obtained from hydrothermal synthesis by high-pressure impregnation possessed much larger surface area and pore volume than semi-coke support,and they were significantly reduced after the desulfurization reaction.The equivalent grain model was reasonably used to analyze experimental data,in which k s=4.382×10-3 exp(-8.270×103/RgT) and Dep=1.262×10-4exp(1.522×104/RgT).It suggests that the desulfurization reaction of the Z20SC sorbent is mainly controlled by the chemical reaction in the initial stage and later by the diffusion through the reacted sorbent layer.     

Adsorptive desulfurization over hierarchical beta zeolite by alkaline treatment

Hierarchical beta zeolites with SiO2 /Al2O3 molar ratios of 16 to 25 were obtained by alkaline treatment in NaOH solution. The effects of treatment temperature on crystallinity, textural properties and chemical composites were studied by XRD, N2 sorption, FT-IR and XRF techniques. The desulfurization performance of parent and alkaline-treated beta zeolites was investigated by static absorption in four model fuels, containing four sulfur compounds of different molecular sizes like thiophene (TP), 3-methylthiophene (3-MT), benzothiophene (BT) and dibenzothiophene (DBT), respectively. The crystallinity was observed to be successfully maintained when the treatment temperature was below 50 C. Mesoporosity of beta zeolite was evidently developed with alkaline treatment. The formation of mesopore remarkably improved the desulfurization performance for TP, 3-MT, BT and DBT, especially for DBT with larger molecular diameter. Though the addition of toluene in the model fuels resulted in a significant drop of the desulfurization performance of mesoporous beta zeolite, the introduction of cerium ions to some extent mitigated the effect of toluene, which means that both the adsorbents porous structure and the adsorption mode are responsible for the desulfurization performance. The adsorbent of cerium ion-exchanged mesoporous beta showed about 80% recovery of desulfurization after the first regeneration.     

Studies on Mechanisms and Blockade of Carcinogenic Action of Female Sex Hormones

Tumours of mice are induced by administration of Inj. Hydroxyprogesteroni Caproatis Co. (EP) in a practical subthreshold dose of carcinogenesis or 2. 5-5 times the human contraceptive dose (simply referred to as 2. 5- to 5-fold dose) combined with whole-body 0. 5 Gy gamma-ray irradiation. Malignant transformation of Syrian golden hamster embryo (SHE) cells is also induced by 5-fold dose of EP combined with 0. 3 Gy gamma-ray irradiation in vitro, thereby indicating that synergistic carcinogenesis can be obtained by combined use of physical and chemical carcinogens.The mechanisms of synergistic carcinogenesis have been further explained by cytogenetics, damage extent of the target cell DNA and production of free radicals. The Chinese traditional medicine with antioxidat-ing effect (Sulekang Capsule, SC), food additive--butylated hydroxyanisole (BHA) and green tea can effectively inhibit the carcinogenic effect of EP or EP combined with gamma rays in mice. They all have marked ability to scavenge or remove     

3D-printing of integrated spheres as a superior support of phosphotungstic acid for deep oxidative desulfurization of fuel

Construction of catalysts with integral structure for oxidative reaction process is an essential promotion to catalysts in industrial application.In this work,a 3D printing method was employed to prepare 3D printed spheres(3D-PSs),followed by carbonization to form 3D carbon spheres(3D-CSs).Then,a 3D-CSs supported phosphotungstic acid(HPW/3D-CSs)was prepared for deep oxidative desulfurization.Compared with traditional powder catalysts,the as-prepared catalyst is easy to be operated and separated from oil products.The supported catalyst possesses excellent catalytic performance and the removal of DBT,4-MDBT and 4,6-DMDBT in fuel oil,reaching^100%of sulfur removal.The effects of various experimental parameters on desulfurization efficiency were considered to optimize reaction conditions.Moreover,the catalyst shows excellent thermal and chemical stability,with no obvious decrease in desulfurization activity after 5 cycles.GC–MS analysis indicates DBT sulfone was the solely oxidized product of DBT.     

Interface diffusion and chemical reaction of PZT layer/Si (111) sample during the annealing treatment in air

The interface diffusion and chemical reaction between a PZT (PbZrxTi1-xO3) layer and a Si(111) substrate during the annealing treatment in air have been studied by using XPS (X-Ray Photoelectron Spectroscopy) and AES (Auger Electron Spectroscopy). The results indicate that the Ti element in the PZT precursor reacted with residual carbon and silicon, diffused from the Si substrate, to form TiCx, TiSix species in the PZT layer during the thermal treatment. A great interface diffusion and chemical reaction took place on the interface of PZT Si also. The silicon atoms diffused from silicon substrate onto the surface of PZT layer. The oxygen atoms, which came from air, diffused into silicon substrate also and reacted with Si atoms to form a SiO2 interlayer between the PZT layer and the Si (111) substrate. The thickness of SiO2 interlayer was proportional to the square root of treatment time. The formation of the SiO2 interlayer was governed by the diffusion of oxygen in the PZT layer at low annealing tempera     

Effects of ultrasound on the desulfurization performance of hot coal gas over Zn-Mn-Cu supported on semi-coke sorbent prepared by high-pressure impregnation method

Zn-Mn-Cu/SC(U) sorbent was hydrothermally synthesized by ultrasound-assisted high-pressure impregnation method with semi-coke(SC)as support and the mixed solution of zinc nitrate,manganese nitrate and copper nitrate as active component precursors.The desulfurization performances of hot coal gas on the prepared sorbent at a mid-temperature of 500°C were tested in fixed-bed reactor.Morphology and pore structure of the prepared sorbent were also characterized by TEM,N2adsorption/desorption isotherms and XRD.For comparison,the sorbent of Zn-Mn-Cu/SC prepared by conventional high-pressure impregnation was also evaluated and characterized in order to study the effects of ultrasound treatment.Zn-Mn-Cu/SC(U) sorbent prepared by high-pressure impregnation under ultrasound-assisted condition showed a better desulfurization performance than Zn-Mn-Cu/SC.It could remove H2 S from 1000×10-6m3/m3 to 0.1×10-6m3/m3 at 500°C and maintained for 12.5 h with the sulfur capacity of 7.74%,in which both the breakthrough time and sulfur capacity were about 32% and 51% higher than those of Zn-Mn-Cu/SC sorbent.The introduction of ultrasound during high-pressure impregnation process greatly improved the morphology and pore structure of the sorbent.The ultrasonic treatment made particle size of active components smaller and made them more evenly disperse on semi-coke support,which provided more opportunities to contact with H2S in coal-based gases.However,there were no any difference in compositions and existing forms of active components on the Zn-Mn-Cu/SC and Zn-Mn-Cu/SC(U) sorbents.     

The effects of ultrasound frequency and power on the activation energy in Si-KOH reaction system

The activation energy is the minimum amount of energy required to initiate a reaction. It is one of the important indexes for appraising a reaction. The chemical reaction rate is closely related to the value of activation energy, and reducing activation energy is propitious to promoting a chemical reaction. In the present paper, the relationship between the activation energy in Si-KOH reaction system and the ultrasound frequency and power has been discussed for the first time. The range of ultrasound frequency and power is 40-100kHz （interval by 20kHz） and 10-50W （interval by 10W）, respectively. The experimental clata indicate that the activation energy decreases with the increasing ultrasound power. Comparing with the activation energy without ultrasound irradiation, the results in our paper indicate that ultrasound irradiation could reduce the activation energy in Si-KOH reaction system and increase the reaction rate.     

Environmentally Benign Synthesis of 2-Pyrazolines and Cyclohexenones Incorporating Naphthalene Moiety and Their Antimicrobial Evaluation

We reported the environmental benign synthesis of chalcones,2-pyrazolines and cyclohexanones under microwave irradiation.Chalcones were obtained by the condensation of each of 2-hydroxyacetophenone derivatives with a-naphthaldehyde under microwave irradiation.The condensation reactions of each of synthesized chalcones with phenyl hydrazine under microwave irradiation in the presence of dry acetic acid as a cyclizing agent gave 2-pyrazolines.Also,the new cyclohexenone derivatives,valuable intermediates to synthesize fused heterocycles,have been prepared by the cyclocondensation of each of hydroxychalcones with ethyl acetoacetate.The structures of the synthesized compounds were elucidated by infrared（IR） spectrometry,nuclear magnetic resonance（NMR）,mass spectrometry（MS） and elmental analysis.The results indicate that unlike classical heating,microwave irradiation results in higher yields with shorter and cleaner reactions.The synthesized compounds were screened for antimicrobial activity against Staphylococcus aureus,Escherichia coli,Candida Albicans and Aspergillus niger.We clarified the effects of different substituents in the tested compounds on the obtaind antibacterial activities and antifungal activities.     

CATALYTIC PROPERTIES OF POLYMER-STABILIZED COLLOIDAL METAL NANOPARTICLES SYNTHESIZED BY MICROWAVE IRRADIATION

Catalytic properties of polymer-stabilized colloidal metal nanoparticles synthesized by microwave irradiation were studied in the selective hydrogenation of unsaturated aldehydes, o-chloronitrobenzene and the hydrogenation of alkenes. The results show that nanosized metal particles synthesized by microwave irradiation have similar catalytic performance in selective hydrogenation of unsaturated aldehydes, better selectivity to o-chloroaniline in hydrogenation of o-chloronitrobenzene and higher catalytic activities in hydrogenation of alkenes, compared with metal clusters prepared by conventional heating. The same apparent activation energy (Ea = 29 kJ mol^-1) for hydrogenation of 1-heptene catalyzed with platinum nanoparticles prepared by both heating modes implied that the reaction followed the same mechanism.     

Ionic liquid mediated CO2 activation for DMC synthesis

Promoted catalytic reaction between methanol and CO2 for dimethyl carbonate(DMC) synthesis is conducted over K2CO3/CH3 I catalyst in the presence of ionic liquid under microwave irradiation.The effect of ionic liquids incorporated with microwave irradiation on the yield of DMC is investigated.DMC was found to form at lower temperature in a relative short time,which indicated an enhanced catalytic process by ionic liquid.Among the ionic liquids used,1-butyl-3-methylimidazolium chloride is the most effective promoter.Density functional theory calculations indicate that CO2 bond lengths and angles changed due to the molecular interaction of ionic liquid and CO2,resulting in the activation of CO2 molecules and consequently the acceleration of reaction rate.     

Polycyclic aromatic hydrocarbons in the centralized wastewater treatment plant of a chemical industry zone: Removal, mass balance and source analysis

Increased attention has been given to the fate of pollutants such as polycyclic aromatic hydrocarbons (PAHs) introduced to the wastewater treatment plants.Dissolved and adsorbed PAHs were detected in the centralized wastewater treatment plant of a chemical industry zone in Zhejiang Province,China.The most abundant PAHs were the low molecular weight PAHs (e.g.,Acy,Ace,Flu and Phe),accounting for more than 80% of the total 16 PAHs in each treatment stage.Phase partitioning suggested that the removal of PAHs in every treatment stage was influenced greater by the sorption of particles or microorganisms.The removal efficiencies of individual PAHs ranged between 4% and 87% in the primary sedimentation stage,between 1% and 42% in anaerobic hydrolysis stage,between <1% and 70% in aerobic bio-process stage,between 1.5% and 80% in high-density clarifier stage,and between 44% and 97% in the whole treatment process.Mass balance calculations in primary stage showed significant losses for low molecular weight PAHs and relatively good agreements for high molecular weight PAHs as well as in anaerobic hydrolysis,high-density clarifier stage and sludge stream for most PAHs.Great gains of 60%-150% were obtained for high molecular weight PAHs in aerobic bio-process stage due to biosorption and bioaccumulation.Our investigations found that PAHs entering the wastewater treatment plant (WWTP) could be derived from the dyeing chemical processes as the byproducts,and the contribution supported by the largest dyeing chemical group was up to 48%.     

Impact of impregnation pressure on desulfurization performance of Zn-based sorbents supported on semi-coke

High-pressure impregnation, a new preparation method for sorbents to remove H2S from hot coal gas, is introduced in this paper. Semi-coke (SC) and ZnO is selected as the support and active component of sorbent, respectively. The sorbent preparation process includes high-pressure impregnation, filtration, ovendry and calcination. The aim of this research is to primarily study the effects of the impregnation pressure on physical properties and desulfurization ability of the sorbent. The desulfurization experiment was carried out in a fixed-bed reactor at 500°C and a simulated coal gas used in this work was composed of CO (33 vol%), H2 (39 vol%), H2S (300 ppm in volume), and N2 (balance). Experimental results show that the pore structure of the SC support can be improved effectively and ZnO active component can be uniformly dispersed on the support, with the small particle size of 10-500 nm. Sorbents prepared using high-pressure impregnation have better desulfurization capacity and their active components have higher utilization rate. P20-ZnSC sorbent, obtained by high-pressure impregnation at 20 atm, has the best desulfurization ability with a sulfur capacity of 7.54 g S/100g sorbent and a breakthrough time of 44 h. Its desulfurization precision and efficiency of removing H2S from the middle temperature gases can reach <1 ppm and >99.7%, respectively, before sorbent breakthrough.     

A Novel Method for Synthesizing 6-Chloro and 6-Methoxy purinenucleoside

Starting from tetraacetylribofuranose and 6-chloropurine, in the presence of p-toluenesulfonic acid as catalyst, the intermediate 2′,3′,5′-tri-O-acetyl-6-chloropurinenucleoside was synthesized for the first time under microwave irradiation. The title compound 6-chloro-9-β -D-purinenucleoside (IV) and 6-methoxy-9-β-D-purinenucleoside (V) was easily obtained by treatment of the intermediate (III) with Na2CO3 in CH3OH solution refluxing for 8min and 2hr respectively. Cl AcO OAc…     

Study of oxidative desulphurization process of coal with different metamorphism degrees

The oxidative desulphurization process of coal with different metamorphism degrees treated by an air-steam mixture has been studied.It has been shown that the pyrite present in black coal and anthracite is oxidized with the sulphur dioxide formation,and the process chemical mechanism does not depend on the quality of organic matter.The medium-metamorphized coal,capable of turning into a plastic state and cake in the range of investigated temperatures(350～450 ℃),is desulphurized with the greatest difficulty.The chemical mechanism dealing with the transformations of pyritic sulphur present in brown coal differs from similar processes taking place in black coal and anthracite,because FeS2 is converted with hydrogen sulphide formation at desulphurization.     

Degradation of organic pollutants by visible light synergistic electro-Fenton oxidation process

Visible light irradiation combined with homogeneous iron and/or hydrogen peroxide to degrade organic dye rhodamine B (RhB) and small molecular compound 2,4-dichlorophenol (2,4-DCP) in a home-made bottle reactor was assessed. The concen-tration of oxidize species, Fe3+ and Fe2+ were determined during the degradation process. The results demonstrated that visible light irradiation combined with electro-Fenton improved the degradation efficiency. Moreover, both RhB and 2,4-DCP were mineralized during visible light synergistic electro-Fenton oxidation process. 95.0% TOC (total organic carbon) removal rate of RhB occurred after 90 min and 96.7% of COD (chemical oxygen demand) removal rate after 65 min of irradiation. 91.3% TOC removal rate of 2,4-DCP occurred after 16 h of irradiation and 99.9% COD removal rate occurred after 12 h of illumination. The degradation and oxidation process was dominated by the hydroxyl radical ( · OH) generated in the system. Both the impressed electricity and dye sensitization by visible light facilitated the conversion between Fe3+ and Fe 2+ , thus, improving Fenton reaction efficiency.     

SYNTHESIS OF PPCuPc FILM BY MICROWAVE PLASMA CHEMICAL VAPORIZATION DEPOSITION(MPCVD)

Using a low power microwave generator(W_(max)=100W) and a Surfatron discharge device, Plasma-polymerized copper phthalocyanine (PPCuPc) film was synthesised from monomer copper phthalocyanine(CuPc) by microwave plasma chemical vaporization deposition(MPCVD) with Ar as incorporation gas. The film was characterized by FTIR and ESCA. The role of dissociation of chemical bond in the polymerization process and the influence of substrate temperature and material on deposition were investigated in some detail.     

Epoxy-based azo polymers with high chromophore density: Synthesis,characterization and photoinduced birefringence

Three epoxy-based azo polymers(PEP-AZ-Cl,PEP-AZ-CN and PEP-AZ-NT) with high chromophore density were synthesized by using post-polymerization azo-coupling reactions between epoxy-based precursor polymer(PEP-AN) and diazonium salts of 4-chloroaniline,4-aminobenzonitrile and 4-nitroaniline,respectively.The structures and properties of the azo polymers were characterized by using ~1H-NMR,FT-IR,UV-Vis and thermal analyses.The photoinduced birefringence of the azo polymers was studied by irradiating spin-coated films of the polymers with laser beam at three different wavelengths(488,532,and 589 nm).The results indicate that the photoinduced birefringence of the azo polymers is related with the electron-withdrawing group on azo chromophores and the excitation wavelength.The excitation wavelength that can cause the efficient responses is determined by the absorption band positions of the azo chromophores,which are mainly affected by the electron-withdrawing group on the chromophores.Therefore,the azo polymers containing chromophores with different electron-withdrawing groups show different responsive behavior to the irradiation light at different wavelengths.When irradiated with 488 nm light,PEP-AZ-Cl shows the shortest time to reach the saturated birefringence but with the lowest saturation birefringence level compared with the other two azo polymers.When irradiated with 532 nm light,PEP-AZ-CN shows the shortest time to reach the saturated birefringence.When irradiated with 532 and 589 nm light,PEP-AZ-NT shows the highest saturation birefringence level.     

Theoretical insight into the enhanced CH_4 desorption via H_2O adsorption on different rank coal surfaces

The density functional theory was used to investigate the adsorption of CH_4 and H_2O on different rank coal surfaces.The coal rank is the dominant factor in affecting the adsorption capacity of coal.In order to better understand gas and water interaction with coal of different maturity,we developed fourteen coal models to represent the different rank coal.The interactions of CH_4 and H_2O with coal surfaces were studied and characterized by their adsorption energies,Mulliken charges and electrostatic potential surfaces.The results revealed that the interaction between coal and CH_4 was weak physical adsorption,and that the interaction between coal and H_2 O consisted of physical and chemical adsorption.Adsorption energy of coal–H_2O system was larger than that of coal–CH_4 on all rank coals,suggesting that the adsorption priority in the coal models is H_2 O CH_4.Consequently,the injection of H_2 O into the different rank coal could effectively enhance the coal bed methane(CBM) recovery.     

Plasma modification of polypropylene surfaces and grafting copolymerization of styrene onto polypropylene

The surface of polypropylene(iPP) is modified with glow discharge plasma of Ar,so that the modified surfaces of iPP films are obtained.The studies of scanning electron microscopy(SEM) show the surface etching pattern of iPP films. The chemical structures of iPP films are confirmed by X-ray photoelectron spectroscopy(XPS) and Fourier transform infrared(FTIR) spectroscopy.The wetting properties of modified surfaces of iPP films are characterized by contact angle, and the free energy of surfaces is calculated.The free radical of modification surfaces of iPP is measured by chemical method.The surfaces of iPP are achieved with Ar plasma treatment followed by grafting copolymerization with styrene(St) in St.The grafting polymer of St onto iPP is characterized by FTIR.The grafting rate is dependent on plasma exposure time and discharge voltage.The studies show that homopolymerization of St is undergone at the same time during the grafting-copolymerization of St onto iPP.     

Acceleration of Organic Reactions Using Microwave

The use of microwave technology in accelerating organic reactions has received intense attention leading to immense growth recently. Accordingly, we have been interested in improving the efficacy of organic processes by microwave irradiation. Here we report our results on the microwave assisted direct amide formation from carboxylic acid and amine, the hydrolysis of biopolymers, and nucleophilic aromatic substitution reaction. The reactions carried out under microwave irradiation, in general, …