La_(0.5)Na_(0.5)TiO_3纳米晶的制备及光致发光研究

以硬脂酸、硝酸镧、氢氧化钠和钛酸四丁酯为原料制备了La0 .5Na0 .5TiO3 纳米晶 ,粒度最小可达 1 4nm ,烧成温度为 50 0℃ ,低于传统固相反应的合成温度。光致发光研究表明 :用 392nm光作激发光 ,在室温下观察到了一个强的蓝光发射带 ,并且它的强度和半宽度随粒度发生明显变化。     

Eu0.5RE0.5Fe0.5Mn0.5O3的57Fe Msosbauer谱研究

利用固相反应合成了Eu0.5RE0.5Fe0.5Mn0.5O3(RE=La,Pr,Nd,Sm,Eu,Gd,Tb,Dy,Ho,Er,Tm,Yb,Y)等化合物。测量了其XRD谱及57FeMssbauer谱。实验发现,随着RE原子序数的增加,样品的晶胞体积减小,Fe在化合物中处于Fe3+的高自旋状态,57Fe的四极裂矩与样品的畸变参数D成线性关系。     

Bi_(0.5)Na_(0.5)TiO_3的制备及光催化性能研究

以Bi(NO3)3·5H2O、Na OH、Ti(OC4H9)4为原料,采用水热法制备Bi0.5Na0.5Ti O3纳米光催化剂。用XRD、TEM表征了Bi0.5Na0.5Ti O3光催化剂的结构和形貌。以亚甲基蓝为模型污染物,考察了不同浓度的Na OH对Bi0.5Na0.5Ti O3晶体在紫外光和可见光照射下光催化活性的影响。通过荧光技术研究了Bi0.5Na0.5Ti O3光催化剂表面羟基自由基的生成,探究了清除剂对光催化降解污染物活性的影响。结果表明:Na OH的浓度对Bi0.5Na0.5Ti O3光催化剂的紫外光和可见光活性有很大的影响,当Na OH浓度为8mol·L-1时制备的Bi0.5Na0.5Ti O3晶体光催化活性最高,光照1h,亚甲基蓝的紫外及可见光催化降解率分别达到69.8%、53.4%,在光催化降解过程中·O2ˉ和·OH起主要作用,尤其是·O2-起了重要作用。     

氢化燃烧法合成La1.5Ni0.5Mg17的工艺优化

采用正交实验设计方法安排实验，运用L9(3^4)优化氢化燃烧法合成La1.5Ni0.5Mg17的工艺，考察了施压制饼时间、合成保温时间、合成起始氢气压力、保温温度4个因素对储氢材料的储放氢容量和速率的影响，通过直观分析和方差分析得出优化的工艺为：保温温度903K，制饼施压时间40min，合成起始氢气压力为1MPa，合成保温时间1800min。此条件下合成储氢材料La1.5M0.5Mg17在573K的储放氢容量分别为：5．40和5．15％H(质量分数)；储放氢速率分别为：0．734和0.681％H／min。用XRD分析了材料吸氢和脱氢后的物相结构发现：用Ni适量取代La2Mg17中的La没有导致结构变化，存在的LaNi5，LaH3和La改善了材料的吸放氢速率。     

La0.5-xNdxBa0.5CoO3化合物的磁性和输运特性

在La0.5-xNdxBa0.5CoO3化合物中用Nd对La进行了替代研究，结果表明，Nd的掺入未改变Co3d电子的巡游性。随Nd含量增大，材料的分子磁矩单调下降，当Nd含量大于或等于0.45时，材料中出现了磁性相分离，当x≤0.45时，随Ｎd含量增加，材料的居里温度单调下降，这是由于稀土离子的尺寸效应。电阻测量表明，在所研究的温度范围内，在居里点以下，材料属热扩散导电，在居里点以上属极化子的变程跳跃导电。     

染料敏化La~(3+)掺杂的TiO_2纳晶薄膜制备及其光电性能

采用溶胶-凝胶法制备出La3+掺杂的TiO2纳米粉体材料,通过料浆喷涂工艺制得掺杂La3+的TiO2薄膜并将其以N719染料敏化制成染料敏化太阳能电池(DSSC)。以X射线衍射(XRD)、扫描电镜(SEM)和DSSC测试系统对制得的La3+掺杂的TiO2纳米粉体材料、相应的La3+掺杂的TiO2薄膜以及制成的DSSC分别进行测试表征,研究了La3+掺杂对TiO2晶型和染料敏化太阳能电池性能的影响。XRD测试结果表明,La3+的掺杂改善了TiO2的颗粒分布;电池的测试结果说明,La3+掺杂量为0.5%,煅烧温度为450℃时制备的纳米TiO2膜DSSC电池性能最佳,光电转换效率达1.926%。     

钙钛矿型氧化物Ln0.5Sr0.5CoO3的制备与电输运性能

采用固相反应法合成钙钛矿氧化物材料Ln0.5Sr0.5CoO3（h=La，Pr，Nd，Sm，Eu）的超细粉体，研究了不同稀土元素掺杂时的晶体结构和电输运性能，分析了该钙钛矿体系结构的形成过程。实验表明，当烧结温度达到1200℃时，通过固相反应法可以形成稳定的单一的钙钛矿相。样品电导率在700℃附近出现最大值，低温段的导电行为符合小极化子导电机制，La0.5Sr0.5CoO3材料的电导率在中温范围内最大，适合作为中温固体燃料电池的阴极材料。     

高性能Sm0.5Sr0.5CoO3阴极的制备与表征

用固相合成法合成了Sm0.5Sr0.5CoO3 (SSC)中温固体氧化物燃料电池阴极材料.以La0.9Sr0.1Ga0.8Mg0.2O3为电解质,利用多种技术考察了不同温度(1173～1373 K)焙烧的SSC阴极,以及1173 K 焙烧、掺杂La0.8Sr0.2Ga0.8Mg0.15Co0.05O3(LSGMC5)或La0.8Sr0.2Ga0.8Mg0.09Co0.11O3 (LSGMC11)高氧离子电导材料的复合SSC阴极.SEM的结果显示,随着电极焙烧温度的增加,电极的颗粒度增大,孔隙度减小；LSGMC5、LSGMC11的掺杂对电极微观结构影响不大.交流阻抗和极化实验的结果表明,SSC电极的活性随电极焙烧温度的增加而减小,电极的最佳焙烧温度在1173 K左右；掺杂了LSGMC5或LSGMC11的复合SSC电极的活性以及稳定性显著高于SSC电极.     

Li3V2(PO4)3/C和Li2.5Na0.5V2(PO4)3/C的结构和电化学性能的比较研究

采用溶胶-凝胶法合成了锂离子正极材料Li3V2(PO4)3/C(LVP/C)及Li2.5Na0.5V2(PO4)3/C,并用XRD、循环伏安及交流阻抗等方法,研究了大量Na+掺杂对材料结构和电化学性能影响。结果表明,大量钠离子的掺杂会使LVP结构由单斜向菱方转变。掺杂化合物Li2.5Na0.5V2(PO4)3/C在0.5 C充电1 C放电时,首次放电容量为118 mAh.g-1,50次循环后容量保持率为92.4%,并发现与单斜LVP存在多个放电平台不同,Li2.5Na0.5V2(PO4)3/C仅在3.7 V处有一个放电平台。     

可见光完全分解水光催化剂Bi0.5La0.5VO4的制备和表征

通过高温固相法合成了光催化剂Bi0.5La0.5VO4,用N2吸附-脱附、X射线衍射、扫描电镜和紫外-可见漫反射光谱对催化剂进行了表征,并初步讨论了其能带结构.结果表明,Bi0.5La0.5VO4为BiVO4和LaVO4的固溶体,其禁带宽度约为2.70eV,对应的吸收边为470nm,负载Pt,RuO2和Pt-Cr2O3等后,在紫外光和可见光下均有光催化活性.其中负载Pt-Cr2O3时,其光催化活性最高,可以在紫外光和可见光下完全分解水.在紫外光照射下,生成氢气和氧气的速率分别为28.86和14.34μmol/h.结果还表明,通过形成固溶体来调节价带和导带,是获得可见光响应光催化剂的一种可行的方法.     

Magnetoresistance in La0.5Sr0.5MnO2.5

Resistance measurements indicate the presence of magnetoresistance in the La_0.5Sr_0.5MnO_2.5 brownmillerite related compound. An 80 % of magnetoresistance is found at 75 K. In spite of the partial break‐up occurring at the 3D network of octahedra sharing corners, characteristic of the full oxygen content perovskite phase, the oxygen deficient compound exhibits complex magnetic and electric properties. Such behavior can be explained on the basis of ferromagnetic and metallic clusters randomly distributed at the octahedral layers separated from each other by an insulating antiferromagnetic matrix. AC susceptibility measurements suggest spin glass behavior at low temperature as a consequence of the competition between different magnetic interactions.     

Amorphous Mo-doped NiS0.5Se0.5 Nanosheets@Crystalline NiS0.5Se0.5 Nanorods for High Current-density Electrocatalytic Water Splitting in Neutral Media

It is vitally important to develop highly active, robust and low-cost transition metal-based electrocatalysts for overall water splitting in neutral solution especially at large current density. In this work, amorphous Mo-doped NiS_0.5Se_0.5 nanosheets@crystalline NiS_0.5Se_0.5 nanorods (Am−Mo−NiS_0.5Se_0.5) was synthesized using a facil one-step strategy. In phosphate buffer saline solution, the Am−Mo−NiS_0.5Se_0.5 shows tiny overpotentials of 48 and 209 mV for hydrogen evolution reaction (HER), 238 and 514 mV for oxygen evolution reaction (OER) at 10 and 1000 mA cm⁻², respectively. Moreover, Am−Mo−NiS_0.5Se_0.5 delivers excellent stability for at least 300 h without obvious degradation. Theoretical calculations revealed that the Ni sites in the defect-rich amorphous structure of Am−Mo−NiS_0.5Se_0.5 owns higher electron state density and strengthened the binding energy of H₂O, which will optimize H adsorption/desorption energy barriers and reduce the adsorption energy of OER determining step.     

SrAu0.5Pt0.5 and CaAu0.5Pt0.5, analogues to the respective Ba compound,but featuring purely intermetallic behaviour

Both, SrAu_0.5Pt_0.5 and CaAu_0.5Pt_0.5, have been synthesized by reaction of corresponding mixtures of the pure elements at 1223 K in an argon atmosphere, and characterized by single-crystal X-ray analysis as well as by magnetic susceptibility and electric resistivity measurements. The new compounds crystallize in the CrB type of structure and thus are isostructural to BaAu_0.5Pt_0.5 (SrAu_0.5Pt_0.5: Cmcm; a = 4.262(1) Å; b = 11.435(3) Å; c = 4.632(1) Å; Z = 4; CaAu_0.5Pt_0.5: Cmcm; a = 3.9858(4) Å; b = 10.920(1) Å; c = 4.5249(5) Å; Z = 4). SrAu_0.5Pt_0.5 as well as CaAu_0.5Pt_0.5 are poor metallic conductors with ρ_300K = 0.95 mΩ.cm and ρ_300K = 3.93 mΩ.cm, respectively, and featuring diamagnetic behaviour.According to ESCA measurements SrAu_0.5Pt_0.5 and CaAu_0.5Pt_0.5 both can be formulated as having intermetallic character, showing a negligible electron transfer from alkaline earth metals to the noble metals.     

Magnetoelectric perovskite (Bi0.5Pb0.5)(Fe0.5Zr0.5)O3: Preparation,structural and magnetic properties

The perovskite (Bi_0.5Pb_0.5)(Fe_0.5Zr_0.5)O₃ was synthesized by solid-state reaction in an attempt to find magnetoelectric materials, in which ferroelectricity and ferromagnetism coexist. This complex perovskite has been studied by X-ray and neutron powder diffraction in combination with magnetic measurements. The compound crystallizes in the orthorhombic space group Pbam with a ～ √2a_p, b ～ 2√2a_p and c ～ 2a_p (with a_p ～ 4.057 Å). The field and temperature dependence of the magnetization combined with neutron diffraction data showed antiferromagnetic behavior with the Neel temperature, T_N ～ 450 K. Rietveld refinements of neutron powder diffraction data collected at different temperatures, between 10 and 700 K, have been carried out in order to extract information about the thermal evolution of the nuclear and magnetic structures. A distorted orthorhombic perovskite structure was found within the whole temperature interval. The Bi/Pb and Fe/Zr ions were found to be partially ordered over the perovskite A-site and disordered over the B-site. The neutron diffraction patterns of the (Bi_0.5Pb_0.5)(Fe_0.5Zr_0.5)O₃ sample showed evidence of a long-range magnetic ordering below T_N with a propagation vector k = (0,0,0) and an antiferromagnetic arrangement of the magnetic moments of the Fe³⁺ cations in the B-site. This is consistent with an A_y-type magnetic structure. The factors governing the structural and magnetic properties of (1 ? x)BiFeO₃–xPbZrO₃ solid solutions are discussed and compared with those of pure BiFeO₃ and PbZrO₃. A solid solution strategy for developing magnetoelectric properties in BiFeO₃-based compounds is described, with the aim of realizing both a spontaneous polarization and magnetization at room temperature.     

Ultra-incompressible Ternary Diborides Re_（0.5）Ir_（0.5）B_2,Re_（0.5）Tc_（0.5）B_2,Os_（0.5）W_（0.5）B_2 and Os_（0.5）Ru_（0.5）B_2：Density Functional Calculation

In this paper, density functional computations have been applied to the structural, elastic and electronic properties of ternary transition metal diborides Re0.5Ir0.5B2, Re0.5Tc0.5B2, Os0.5W0.5B2 and Os0.5Ru0.5B2 in hexagonal (P63/mmc) and orthorhombic (Pmmn) structures with both local density approximation and generalized gradient approximation. LDA gives smaller lattice parameters and larger elastic moduli than GGA. Both results show that the hexagonal ones are more stable than orthorhombic ones except Os0.5Ru0.5B2. Moreover, the hexagonal structure has superior elastic property than orthorhombic one. Generally speaking, the calculated elastic moduli of Re0.5Ir0.5B2 and Os0.5Ru0.5B2 are smaller than those values of Re0.5Tc0.5B2 and Os0.5W0.5B2 within the same structure because of the filling of antibonding states. The relativistic effects result in weaker bonds of Tc-B (Ru-B) than those of Re-B (Os-B). All the diborides are ultra-incompressible. Re0.5Tc0.5B2 has the largest shear modulus and it is a promising superhard diboride like Os0.5W0.5B2. The elastic properties are in high correlation with the bond strength. The shear moduli are more sensitive than the bulk moduli to the bond strength.     

稀土取代的复合氧化物Eu_（0．5）RE_（0．5）Fe_（0．5）Mn_（0．

利用固相反应合成了稀土取代的复合氧化物Ｅｕ_（０．５）ＲＥ_（０．５）Ｆｅ_（０．５）Ｍｎ_（０．５）Ｏ_３（ＲＥ＝Ｌａ，Ｐｒ，Ｎｄ，Ｓｍ，Ｇｄ，Ｔｂ，Ｄｙ，Ｈｏ，Ｅｒ，Ｔｍ，Ｙｂ）．测量了这些化合物的ＸＲＤ和ＸＰＳ谱。在ＸＰＳ研究中发现，稀土取代而使稀土元素本身的结合能相对于其倍半氧化物中的有所降低；在取代的复合氧化物中，随着ＲＥ离子半径的减小，Ｆｅ、Ｍｎ的结合能随之增加。     

Effect of ZnO on sintering and microwave dielectric properties of 0.5CaTiO3-0.5 (Li0.5La0.5) TiO3 ceramics

The novel calcium titanate-lithium lanthanum titanate doped with zinc oxide (0.10, 0.30, and 0.50 mol. %) ceramic samples were prepared by solid-state reaction route. The phase formation, microstructure, densification, and microwave dielectric properties were investigated. It was found that the doping with zinc oxide led to a decrease in sintering temperature by 25 ^oC as compared with pure calcium titanate lithium lanthanum titanate due to the liquid phase effect. Also, the calcium titanate lithium lanthanum titanate (10ZCTLLT&30ZCTLLT)) doped with lower zinc oxide (0.10 and 0.30 mol. %) led to higher densification parameter. This was followed by increasing the zinc oxide doping up to (0.50 mol. %) which resulted in a decrease in densification and microwave dielectric properties which may be attributed to increase in porosity and grain growth upon the evaporation of zinc and oxygen vacancy. This led to the increase in dielectric loss (≈10 × 10^?4) value with 50ZCTLLT. Hence, the best result of microwave dielectric characteristics was obtained for 0.5CaTiO₃–0.5(Li_0.5La_0.5)TiO₃ with (0.10 and 0.30 mol. % ZnO) 10ZCTLLT and 30ZCTLLT ceramic samples sintered at 1175 ^oC/2h, with low dielectric constant (ε_r) = 4.4–10.5, very low dielectric loss = 1.07-2.23 × 10^?4 and high quality factor (Q x ?) ≈59-55 × 10⁴ at 8 GHz. Consequently, they can be used not only in wireless satellite communications technology but also can be used in the fifth-generation telecommunication 5G technology construction.     

Synthesis and structure of CsLi0.5Al0.5PO4

A new phosphate CsLi_0.5Al_0.5PO₄ with a structure related to the β-tridymite structure has been synthesized by a precipitation method. X-ray powder diffraction, electron probe microanalysis, second harmonic generation of laser radiation, and IR spectroscopy have been used for studying the compound. Differential scanning calorimetry shows that the synthesized phosphate undergoes phase transitions at T _tr = 68 and 130°C. The crystal structure of CsLi_0.5Al_0.5PO₄ was refined on the basis of X-ray powder diffraction data by the Rietveld method in space group P2₁/a (Z = 8) with the unit cell parameters a = 17.8323(3) Å, b = 5.4250(1) Å, c = 9.3666(2) Å, β = 89.984(8)°, V = 906.10(9) ų.