电填充毛细管色谱柱性能的评价

报道了一种毛细管色谱柱的电填充技术,并进行了柱性能的评价研究。实验表明新的填充方法确保了色谱柱的柱效和重现性。     

Capillary electrochromatography using columns packed with a supercritical fluid carrier

Summary Columns for capillary electrochromatography may be prepared by packing reversed phase silica-based material using a supercritical fluid carbon dioxide carrier. Procedures for the in-situ manufacture of frits and UV detection windows, and the wetting of columns are described. The columns were employed in two commercial instruments (and a home-built system), and their properties investigated during the separation of standard mixtures of test compounds. The columns are highly efficient and durable, with reduced plate heights of 1.0–1.4. The repeatability of retention time, peak area and peak height was measured. The influence of applied voltage and column temperature and of electrokinetic injection parameters was explored, along with other practical considerations.     

Continuous‐Bed Columns Containing Sol‐Gel Bonded Packing Materials for Capillary Electrochromatography

Sol‐gel bonded packing materials in continuous‐bed columns have been prepared for capillary electrochromatography (CEC). Three packing materials were investigated: small‐pore Spherisorb ODS1 (3 μm, 80 Å) with octadecyl as stationary phase, small‐pore mixed‐mode Spherisorb ODS/SCX (3 μm, 80 Å) with octadecyl and propyl sulfonic acid as stationary phases, and large‐pore Nucleosil ODS (7 μm, 1 400 Å) with octadecyl as stationary phase. The characteristics of these columns were compared in terms of electroosmotic flow, efficiency, inertness, and retention factors. In contrast to columns containing sol‐gel bonded ODS, columns containing sol‐gel bonded mixed‐mode ODS/SCX generated nearly pH independent electroosmotic flow (EOF) over pH 2–9. Columns containing sol‐gel bonded large‐pore ODS produced nearly three times lower reduced plate height than those containing small‐pore ODS. Efficiencies of 220,000 plates per meter and 175,000 plates per meter were obtained from columns containing sol‐gel bonded 7 μm, 1 400 Å ODS and columns containing sol‐gel bonded 3 μm, 80 Å ODS, respectively, which are among the highest reported efficiencies for continuous‐bed columns. In CEC, over one million plates per meter and pH independent EOF are expected from continuous‐bed columns containing sol‐gel bonded 1.5 μm particles with large pores and mixed‐mode stationary phases.     

Performance evaluation of ion‐exchange chromatography in capillary format

The performance of a recently introduced capillary ion‐exchange chromatography system was explored. Experiments were conducted in isocratic mode with a commercial capillary anion‐exchange column (id = 0.4 mm, L = 15 cm) using a five‐anion standard mixture. The achieved results were compared to the performance of a standard bore ion‐exchange system (id = 4 mm, L = 15 cm), which was considered as a reference. The first‐generation capillary columns exhibited a minimal reduced plate‐height value below two witnessing a good packing quality and system performance. However, compared to the standard bore system the capillary system displayed an increased apparent C‐term which could be due to a difference in packing morphology and/or possible external band‐broadening contributions. For fast separations, the standard bore system outperformed the capillary system, while for complex separations both systems performed nearly equally well. In addition, the retention characteristics of the capillary system were investigated. To illustrate the suitability of the capillary system, the analysis of real‐world water samples originating from two local Belgian rivers was demonstrated.     

Open-tubular nanoelectrochromatography (OT-NEC): gel-free separation of single stranded DNAs (ssDNAs) in thermoplastic nanochannels

Electrophoresis or electrochromatography carried out in nanometer columns (width and depth) offers some attractive benefits compared to microscale columns. These advantages include unique separation mechanisms that are scale dependent, fast separation times, and simpler workflow due to the lack of a need for column packing and/or wall coatings to create a stationary phase. We report the use of thermoplastics, in this case PMMA, as the substrate for separating single-stranded DNAs (ssDNAs). Electrophoresis nanochannels were created in PMMA using nanoimprint lithography (NIL), which can produce devices at lower cost and in a higher production mode compared to the fabrication techniques required for glass devices. The nanochannel column in PMMA was successful in separating ssDNAs in free solution that was not possible using microchip electrophoresis in PMMA. The separation could be performed in <1 s with resolution >1.5 when carried out using at an electric field strength of 280 V/cm and an effective column length of 60 μm (100 nm × 100 nm, depth and width). The ssDNAs transport through the PMMA column was driven electrokinetically under the influence of an EOF. The results indicated that the separation was dominated by chromatographic effects using an open tubular nano-electrochromatography (OT-NEC) mode of separation. Interesting to these separations was that no column packing was required nor a wall coating to create the stationary phase; the separation was affected using the native polymer that was UV/O₃ activated and an aqueous buffer mobile phase.     

Analysis of trace levels of impurities and hydrogen isotopes in helium purge gas using gas chromatography for tritium extraction system of an Indian lead lithium ceramic breeder test blanket module

In the fusion fuel cycle, the accurate analysis and understanding of the chemical composition of any gas mixture is of great importance for the efficient design of a tritium extraction and purification system or any tritium handling system. Methods like laser Raman spectroscopy and gas chromatography with thermal conductivity detector have been considered for hydrogen isotopes analyses in fuel cycles. Gas chromatography with a cryogenic separation column has been used for the analysis of hydrogen isotopes gas mixtures in general due to its high reliability and ease of operation. Hydrogen isotopes gas mixture analysis with cryogenic columns has been reported earlier using different column materials for percentage level composition. In the present work, trace levels of hydrogen isotopes (∼100 ppm of H₂ and D₂) have been analyzed with a Zeolite 5A and a modified γ‐Al₂O₃ column. Impurities in He gas (∼10 ppm of H₂, O₂, and N₂) have been analyzed using a Zeolite 13‐X column. Gas chromatography with discharge ionization detection has been utilized for this purpose. The results of these experiments suggest that the columns developed were able to separate ppm levels of the desired components with a small response time (<6 min) and good resolution in both cases.     

Modeling the effects of column packing quality and residence time changes on protein monomer/aggregate separation

The packing quality of chromatography columns used for the purification of protein therapeutics is routinely monitored to ensure consistent and reproducible performance. In this work, we used established chromatography models to determine the effect of column packing quality and fluid residence time on the separation of protein therapeutic monomer and aggregate species using a hydrophobic interaction chromatography adsorbent (Phenyl Sepharose Fast Flow). The relationship between the number of theoretical plates, fluid residence time, and column separation performance was quantified using modeling simulations. The simulations showed the separation depended on both the fluid residence time and the number of theoretical plates. However, when the number of theoretical plates was increased to ≥150, the simulations predicted that the separation performance of the column was not significantly improved. The approach described here could be used as a method to quantify acceptable height equivalent of a theoretical plate values for columns, and serve as a tool to understand how column packing quality impacts a given chromatographic separation prior to column scale-up, as well as during the monitoring of column lifetime in the manufacturing of large scale protein therapeutics.     

Styrene‐N‐phenylacrylamide co‐polymer modified silica monolith particles with an optimized mixing ratio of monomers as a new stationary phase for the separation of peptides in high performance liquid chromatography

A stationary phase was prepared by chemical derivatization of the support particles with a layer of copolymer composed of styrene and N‐phenyl acrylamide. Silica monolith particles of ca. 2.6 µm (volume‐based average) have been prepared as the support particles by sol‐gel reaction followed by differential sedimentation. The particles were reacted with 3‐chloropropyl trimethoxysilane followed by sodium diethyldithiocarbamate to introduce an initiator moiety. Then, the copolymer layer was immobilized via reversible addition‐fragmentation transfer polymerization. The resultant phase was packed in glass‐lined stainless‐steel micro‐columns (1 x 150 mm) and evaluated for the separation of a mixture composed of five peptides (Trp‐Gly, Thr‐Tyr‐Ser, angiotensin I, isotocin and bradykinin). The effect of monomer mixing ratio (styrene versus N‐phenyl acrylamide) on the chromatographic separation efficiency of the stationary phase was examined. A number of theoretical plates (N) as high as 33 600 plates/column (224 000 plates/m, 4.46 µm plate height) was achieved using the column packed with the optimized stationary phase. The column‐to‐column reproducibility based on three columns packed with three different batches of stationary phase was found satisfactory in separation efficiency, retention factor, and asymmetry factor.     

Study of the influence of the aspect ratio on efficiency, flow resistance and retention factors of packed capillary columns in pressure- and electrically-driven liquid chromatography

The influence of the aspect ratio, rho (rho = column diameter/particle diameter), on column parameters such as efficiency, retention factors and flow resistance was studied in both high-performance liquid chromatography and capillary electrochromatography with packed capillary columns. In order to compare the true efficiencies of different columns, a procedure to account for external band broadening was applied. High efficiencies (reduced plate height h approximately 2) were obtained with capillary columns with internal diameters of 150-, 100-, and 75-microm, packed with 10-microm particles. In contrast to previous reports in the literature, no significant improvements in efficiency or flow resistance were observed when the aspect ratio of such columns was decreased. Our observations suggest that the wall effect in these types of columns is not significant. When the aspect ratio was decreased by increasing the particle size, a decrease in reduced plate height was observed. However, the results of flow resistance measurements showed that the latter effect should be attributed to differences in packing and particle batch quality rather than to differences in the aspect ratio.     

Capillary electrochromatography with 1.5 μm ODS-modified non-porous silica spheres

Summary The particle realization of electrochromatography on capillaries packed with 1.5 μm ODS-modified non-porous silica spheres is demonstrated. In order to realize stable separation conditions it is crucial to add sodium dodecylsulphate (SDS) to the mobile phase and to pressurize both buffer vials at 10 bar. The presence of SDS stabilizes the current and makes the electro-osmotic flow in the packing more uniform so that no air bubbles are generated at high field strengths. The capillary columns are extremely efficient and on a 24 cm long column about 120,000 plates can be generated (a reduced plate height of about 1.3). The columns are very stable and no loss in efficiency was found after using a column continuously for two months.     

Effect of water and protic solvents on polysaccharide-based column efficiency

In the present study, polysaccharide-based columns were used to evaluate the efficiency of columns in response to the introduction of water and protic solvents (methanol and ethanol) into the mobile phase, replacing acetonitrile. While increasing water content frequently enhances enantiomer resolution, the inclusion of water, particularly when combined with methanol and ethanol in the mobile phase, has an adverse impact on mass transfer, thus influencing the column plate height. These effects are more pronounced with ethanol, and in many cases, van Deemter plots exhibit the absence of a minimum point optimal in the explored range. Consequently, acetonitrile and its water mixtures are the preferred choices to mitigate these effects for situations in which the chiral column is operated at a relatively high flow rate (> 1 mL/min in a 4.6 mm column).     

Preparation and use of packed capillary columns in chromatographic and related techniques

In this paper general considerations related to the various approaches and parameters influencing the preparation of highly efficient and stable capillary columns for use in liquid chromatography and related techniques are presented and the column production process is discussed in some detail. The different packing methods available for delivering a packing material into a capillary column are discussed from a practical viewpoint. Packing with a gas (dry packing), packing with a liquid solvent or a mixture of solvents (slurry packing), packing with supercritical carbon dioxide, electrokinetic packing, and sol-gel packing technologies are introduced and discussed throughout the paper. Practical recommendations for obtaining highly efficient (high plate numbers) and stable capillary packed columns are also addressed and discussed.     

Physical properties and structure of fine core–shell particles used as packing materials for chromatography: Relationships between particle characteristics and column performance

The recent development of new brands of packing materials made of fine porous-shell particles, e.g., Halo and Kinetex, has brought great improvements in potential column efficiency, demanding considerable progress in the design of chromatographic instruments. Columns packed with Halo and Kinetex particles provide minimum values of their reduced plate heights of nearly 1.5 and 1.2, respectively. These packing materials have physical properties that set them apart from conventional porous particles. The kinetic performance of 4.6 mm I.D. columns packed with these two new materials is analyzed based on the results of a series of nine independent and complementary experiments: low-temperature nitrogen adsorption (LTNA), scanning electron microscopy (SEM), inverse size-exclusion chromatography (ISEC), Coulter counter particle size distributions, pycnometry, height equivalent to a theoretical plate (HETP), peak parking method (PP), total pore blocking method (TPB), and local electrochemical detection across the column exit section (LED). The results of this work establish links between the physical properties of these superficially porous particles and the excellent kinetic performance of columns packed with them. It clarifies the fundamental origin of the difference in the chromatographic performances of the Halo and the Kinetex columns.     

Dynamics of capillary electrochromatography. II. Comparison of column efficiency parameters in microscale high-performance liquid chromatography and capillary electrochromatography.

In capillary electrochromatography (CEC) the flow of the mobile phase is generated by electrosmotic means in high electric field. This work compares band spreading measured experimentally in several packed capillaries with electrosmotic flow (EOF) and viscous flow under otherwise identical conditions. The data were fitted to the simplified van Deemter equation for the theoretical plate height, H = A + B/u + Cu, in order to evaluate parameters A and C in each mode of flow in the different columns. The ratio of these two parameters obtained with the same column in microscale HPLC (mu-HPLC) and CEC was used to quantify the attenuation of their contribution to band spreading upon changing from viscous flow (in mu-HPLC) to electrosmotic flow (in CEC). The capillary columns used in this study were packed with stationary phases of different pore sizes as well as retentive properties and measurements were carried out under different mobile phase conditions to examine the effects of the retention factor and buffer concentration. In the CEC mode, the value of both column parameters A and C was invariably by a factor of two to four lower than in the mu-HPLC mode. This effect may be attributed to the peculiarities of the EOF flow profile in the interstitial space and to the generation of intraparticle EOF inside the porous particles of the column packing. Thus, band spreading due to flow maldistribution and mass transfer resistances is significantly lower when the mobile phase flow is driven by voltage as in CEC, rather than by pressure as in mu-HPLC.     

Ultrahigh-pressure liquid chromatography using a 1-mm id column packed with 1.5-microm porous particles

The evolution of chromatography has led to the reduction in the size of the packing materials used to fabricate HPLC columns. The increase in the backpressure required has led to this technique being referred to as ultrahigh-pressure liquid chromatography (UHPLC) when the column backpressure exceeds 10000 psi (approximately 700 bar). Until recently, columns packed with sub-2-microm materials have generally fitted into two classes; either short (less than 5 cm) columns designed for use on traditional HPLC systems at pressures less than 5000 psi (350 bar), or capillary columns (inner diameters less than 100 microm). By using packing materials with diameters <2 microm to fabricate UHPLC columns, there is an increase in efficiency and a decrease in the analysis time that are directly proportional to the size of the packing material. In order to realize and exploit the increase in efficiency, however, the columns must maintain lengths typically associated with analytical columns (15-25 cm). We have packed 1 mm diameter, 150 mm in length columns with 1.5 microm packing material, and evaluated their performance in UHPLC. The pressure required to achieve optimum linear velocities in plots of plate height versus linear velocity was in the vicinity of 1104 bar (16000 psi). The 1.5 microm particle-packed column was compared with the more traditional 150 mm long analytical columns packed with 3 microm materials. This column showed an efficiency that was approximately twice that observed with the 3 microm packed column and a concomitant reduction in the analysis time, theoretically predicted.     

Influence of the packing heterogeneity on the performance of liquid chromatography supports

We report on a series of plate height and flow resistance data obtained via computational fluid dynamics simulations in a simplified two-dimensional (2D) mimic of real packed bed and monolithic columns. By varying the external porosity (0.4 < epsilon < 0.8) and the degree of packing randomness, a good qualitative insight in the relationship between the packing porosity and heterogeneity and the general chromatographic performance parameters is obtained, unbiased by any differences in phase retention factor k', mobile phase diffusivity or viscosity or intra-skeleton porosity. The results provide a quantitative support for the use of domain size reduced plate heights as a means to compare the performance of chromatographic beds with a different porosity, as it was found that packings with a similar degree of packing heterogeneity yield very similar domain size reduced h(min)-values, nearly completely independent of the porosity. The study also clearly shows that the presence of preferential flow paths (inevitably accompanied by the presence of more clustered regions) leads to a decrease of the flow resistance, but also leads to a strong increase of the band broadening if supports with the same porosity epsilon and the same radial width are compared. For the presently considered 2D system, the flow resistance reduction is too small to overcome the corresponding strong increase in band broadening, such that the presence of preferential flow paths always leads to an overall increase of the separation impedance.     

不锈钢宽口径填充毛细管液相色谱柱

 设计了一种零死体积的二通式柱尾结构和一种使匀浆填料均匀进入色谱柱管内的储料池 ,研究了制备内径在 0 5mm～ 1 0mm的不锈钢宽口径填充毛细管液相色谱柱的方法。详述了以不同牌号、规格的反相ODS类固定相制备的不同柱长的色谱柱的性能。通过折合板高 /折合流速关系和不对称因子对柱性能进行了评价 ,结果表明 ,该方法制备的色谱柱柱效达到理论值的 75 %以上、RSD为 6% ,稳定性也很好。将其应用于抗癫痫药物和氯苯类化合物的分析 ,结果令人满意。     

Spherical Versus Irregular-Shaped Silica Gel Particles in HPLC

Abstract

With optimised packing procedures, spherical shaped silica gel particles produce 1.5 to 2 times more plates in HPLC than irregular shaped silica gel particles. The lowest reduced plate height obtained by us so far is for 5 μm ROSiL-C₁₈-HL-D and is h: 1.62 for k': 4.5. It is suggested to transform h into 100/h% and to name this the “Chromatographic efficiency”, or a % of the ideal 100% limit. This limit would be an h value equal to the mean particle diameter. Spherical and irregular silica gel particles of 5 and 10 μm particle diameter and with similar physical characteristics have the same permeability in HPLC columns.

Whether a correct column packing procedure is used can be shown by the constancy of plate number and column permeability in function of different packing pressures.     

Using principal component analysis for the study of the retention behaviour of phenol derivatives under reversed-phase conditions

Summary The retention time of 11 ring-substituted phenol derivatives was measured on six different reversed-phase HPLC columns and the log k, theoretical plate number (N) and asymmetry factor (F) values were calculated for each solutes on each column. The similarities and dissimilarities among the columns and solutes were elucidated by principal component analysis followed with nonlinear mapping technique and cluster analysis. Calculations indicated that the retention characteristics of porous graphitized carbon stationary phase considerably deviate from those of octadecyl- and hexyl-coated silica, octadecyl-coated polystyrene-divinylbenzene polymer and polybutadiene-coated alumina. The differences among these columns were markedly smaller. The retention behaviour of aminophenols differed from those of other phenol derivatives proving the importance of molecular polarity in the retention. It was established that the mode of calculation slightly modifies the similarity and dissimilarity among the columns and solutes, therefore, the use of more than one calculation method is proposed.     

Visualization and quantification of the onset and the extent of viscous fingering in micro-pillar array columns

New experimental data of the viscous fingering (VF) process have been generated by studying the VF process in perfectly ordered pillar array columns instead of in the traditionally employed packed bed columns. A detailed quantitative analysis of the contribution of VF to the observed band broadening could be made by following the injected species bands using a fluorescence microscope equipped with a CCD-camera. For a viscosity contrast of 0.16 cP, a plate height increase of about 1 μm can be observed, while for a contrast of respectively 0.5 cP and 1 cP, additional plate height contributions of the order of 5–20 μm were observed. Citing these values is however futile without noting that they also depend extremely strongly on the injection volume of injected sample. It was found that, for a given viscosity contrast of 0.314 cP, the maximal plate height increase varied between 0.5 μm and 18 μm if the injection volume was varied between 3.0 nl and 32.7 nl. These values furthermore also strongly vary with the distance along the column axis.