One-step synthesis of silica hollow particles in a W/O inverse emulsion

Porous silica hollow particles have been fabricated by a one-step approach in water in oil (W/O) inverse emulsion. Ammonia water droplets stabilized by alkyl-phenol polyoxyethylene ether (TX-4) in tetraethoxysilane (TEOS)/cyclohexane solution act as soft templates for constructing the silica hollow particles. The formation mechanism is discussed in detail from the equilibrium between the diffusion and reactions of TEOS and its products (hydrolysates and polycondensates) on the W/O interface. The structure and morphology of the resultant silica hollow particles are well controlled by changing the parameters involving the concentration of TX-4, TEOS, and ammonia. The synthesized products have been characterized using transmission electron microscopy, scanning electron microscopy, solid state NMR, and nitrogen adsorption–desorption measurements.     

反相微乳液法制备纳米SiO2的研究

在壬基酚聚氧乙烯5醚(NP-5)/环己烷/氨水的反相微乳液体系中，进行正硅酸乙酯(TEOS)的水解、缩合反应，得到粒径在30～50 nm的单分散纳米SiO₂胶体。红外光谱法(FTIR)及透射电子显微镜(TEM)观察证明了纳米SiO₂粒子的生成。反相微乳液体系相图的研究表明，水相为氨水比纯水有较窄的W/O型微乳区。氨水微乳液是碱催化TEOS水解、缩合制备纳米SiO₂粒子的适宜体系。当体系中TEOS的浓度增大时，粒子的粒径随之增大。降低NP-5     

Synthesis of Nanosize Silica in a Nonionic Water-in-Oil Microemulsion: Effects of the Water/Surfactant Molar Ratio and Ammonia Concentration

The effect of ammonia concentration on the region of existence of single-phase water-in-oil microemulsions has been investigated for the system polyoxyethylene (5) nonylphenyl ether (NP-5)/cyclohexane/ammonium hydroxide. The presence of ammonia decreases the size of the microemulsion region. A minimum concentration of surfactant (estimated at about 1.1 wt%) is required for solubilization of the aqueous phase; this value is not significantly affected by ammonia concentration. As indicated by fluorescence spectral data, the transition between bound and free water occurs when the water-to-surfactant molar ratio is about 1 and the presence of ammonium hydroxide does not appear to have a significant effect on this. Ultrafine (30-70 nm diameter), monodisperse silica particles produced by hydrolysis of tetraethoxysilane (TEOS) in the microemulsion show a complex dependence of the particle size on the water-to-surfactant molar ratio (R) and on the concentration of ammonium hydroxide. At relatively low ammonia concentration in the aqueous pseudophase (1.6 wt% NH3) the particle size decreases monotonically with increase in R. However, for higher ammonia concentrations (6.3-29.6 wt% NH3) a minimum in particle size occurs as R is increased. These trends are rationalized in terms of (a) the effects of the concentration, structure, and dynamics of the NP-5 reverse micelles on the hydrolysis and condensation reactions of TEOS, and (b) the effects of ammonia concentration on the stability of the microemulsion phase, the hydrolysis/condensation reactions of TEOS, and the depolymerization of siloxane bonds. Copyright 1999 Academic Press.     

Preparation and characterization of silica aquasols

Aquasols containing silica nanoparticles with diameters of 75 to 95 nm were obtained directly by hydrolysis of 2 wt.% tetraethoxysilane (TEOS) in water in the presence of a non-ionic surfactant. The reaction was catalyzed by hydrochloric acid, ammonia, or sodium hydroxide. The particle size, which mainly depends on the concentration of TEOS in water, was determined by dynamic light scattering (DLS). Whereas the catalysts have almost no influence on the particle size, they very strongly affect the morphology of the silica particles formed. The dried SiO(2) particles obtained via the HCl-catalyzed reaction have film-forming properties and show no measurable BET surface area. SiO(2) particles prepared with ammonia as catalyst form nanoporous films on glass, and the BET surface area of the freeze-dried particles is 540 m(2)/g. Using sodium hydroxide as catalyst results in some agglomeration of uniform spherical particles with a BET surface area of 237 m(2)/g. (29)Si MAS NMR investigations of the freeze-dried particles provide information about the degree of condensation and the ratio of "free" hydroxyl groups. The silica aquasols described have a surprisingly high hydrophilizing effect on hydrophobic fibers (PP, PET). Silica nanoparticles of comparable diameters, prepared by the "St?ber method", dispersed in alcohol do not show any hydrophilizing properties worth to mention.     

Synthesis of spherical submicron-sized magnetite/silica nanocomposite particles

This paper describes a method for fabricating spherical submicron-sized silica particles that contained magnetite nanoparticles (magnetite/silica composite particles). The magnetite nanoparticles with a size of ca. 10 nm were prepared according to the Massart method, and were surface-modified with carboxyethylsilanetriol. The fabrication of magnetite/silica composite particles was performed in water/ethanol solution of tetraethoxyorthosilicate with ammonia catalyst in the presence of the surface-modified magnetite nanoparticles. The magnetite/silica composite particles with a size of ca. 100 nm were successfully prepared at 0.05 M TEOS, 15 M water, and 0.8 M ammonia with injection of the magnetite nanoparticle colloid at 2 min after the initiation of hydrolysis reaction of TEOS. Magnetite concentration in the composite particles could be raised to 17.3 wt.% by adjustment of the injected amount of the magnetite colloid, which brought about the saturation magnetization of 7.5 emu/g for the magnetite/silica composite particles.     

Formation of fractal porous silica by hydrolysis of TEOS in a bicontinuous microemulsion

Mesoporous silica particles have been prepared by hydrolysis of TEOS (Si(OC₂H₅)₄) in bicontinuous microemulsions containing polyoxyethylene (POE) dodecylether, isooctane and water. TEOS was dissolved in a continuous water phase and hydrolyzed by the dispersed water at around the phase inversion temperature (60°C). Undulating solid materials with layered mesostructures were produced from middle-phase microemulsions in the three phase region (o/w=0.2–0.7). On the other hand, the solids obtained from the lower aqueous phase in the three phase region were found to have a heterogeneous disordered structure. Measurements of the fractal dimensions were performed in the macropore region using a box-counting method for the outline of the SEM texture. We found that the macropore size distribution in the particles prepared from the middle-phase microemulsion follows the fractal rule with a dimension of 1.7. From the results of nitrogen adsorption/desorption curves on the silica, a steep increase in the adsorption amounts was observed at a relative pressure below 0.2, and adsorption/desorption hysteresis was also observed at a relative pressure between 0.3 and 0.5. These studies suggest that the silica synthesized in the bicontinuous microemulsion mesostructure has a very broad size range from micro to macropores with a fractal distribution.     

Preparation of large monodispersed spherical silica particles using seed particle growth

To obtain large-sized, monodispersed spherical particles of silica by sol precipitation, a seed particle growth method was attempted. The formation of secondary particles during seed particle growth causing a multimodal distribution of particle size was suppressed via fine adjustment of the reaction conditions, such as TEOS, ammonia, and water concentrations, as well as operational conditions such as feeding time and agitation speed. Among the reaction conditions, an increase of TEOS concentration promoted secondary particle formation, resulting in bimodal particle distribution. However, secondary particle formation was depressed with increasing ammonia and water concentrations. In addition, long feeding time (low feed flow rate) and rigorous agitation significantly reduced secondary particle formation because they contributed to the slow generation of supersaturation and rapid seed particle growth, respectively.     

Preparation and properties of uniform coated colloidal particles. VII. Silica on hematite

Spindle-type hematite particles of narrow size distribution were coated with uniform layers of silica by hydrolysis of tetraethylorthosilicate (TEOS) in 2-propanol. The effects of the reaction time and initial concentrations of ammonia and water on the thickness of the silica shell were investigated and the rate of the coating process, in terms of the TEOS concentration, was evaluated.     

Acrylic polymer/silica hybrids prepared by emulsifier‐free emulsion polymerization and the sol–gel process

Acrylic polymer/silica hybrids were prepared by emulsifier‐free emulsion polymerization and the sol–gel process. Acrylic polymer emulsions containing triethoxysilyl groups were synthesized by emulsifier‐free batch emulsion polymerization. The acrylic polymer/silica hybrid films prepared from the acrylic polymer emulsions and tetraethoxysilane (TEOS) were transparent and solvent‐resistant. Atomic force microscopy studies of the hybrid film surface suggested that the hybrid films did not contain large (e.g., micrometer‐size) silica particles, which could be formed because of the organic–inorganic phase separation. The Si? O? Si bond formed by the cocondensation of TEOS and the triethoxysilyl groups on the acrylic polymer increased the miscibility between the acrylic polymer component and the silica component in the hybrid films, in which the nanometer‐size silica domains (particles) were dispersed homogeneously in the acrylic polymer component. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 273–280, 2006     

The use of a thermally reversible bond for molecular imprinting of silica spheres

A silica monomer-estrone complex (EstSi) having a thermally cleavable urethane bond and a cross-linkable triethoxysilane group was synthesized. From EstSi and TEOS, spherical silica particles with sizes of 1.5-3 mum were prepared. The template molecules were removed from the silica matrix by heating at 180 degrees C in DMSO in the presence of water, generating a cavity with an amino group. The control silica particles that had the same sizes and shapes were obtained with aminopropyl triethoxysilane and TEOS. When ethylene glycol was added in place of H2O, an ethyl alcoholic group was formed in the cavity. Their recognition ability and specific binding for estrone were characterized by uptake experiments. The estrone-imprinted silica particles showed a much higher recognition ability than the control silica particles and higher selectivity for estrone than testosterone propionate.     

Study on the morphological regulation mechanism of hollow silica microsphere prepared via emulsion droplet template

The morphology regulation of hollow silica microspheres is significant for their properties and applications. In this paper, hollow silica microspheres were formed through the hydrolysis and condensation reaction of tetraethyl orthosilicate (TEOS) at the interface of the emulsion droplet templates composed of liquid paraffin and TEOS, followed by dissolving paraffin with ethanol. The effects of various factors including the emulsifier structure and content, TEOS content, catalyst type, and the ethanol content in the continuous water phase on the particle size, shell thickness and morphology of the prepared hollow silica microspheres were studied in detail. The results show that the diffusion and contact of TEOS and water molecules as well as the hydrolysis condensation reaction of TEOS at the oil-water interface are two critical processes for the synthesis and morphological regulation of hollow silica microspheres. Cationic emulsifier with a hydrophobic chain of appropriate length is the prerequisite for the successful synthesis of hollow silica microspheres. The ethanol content in water phase is the dominant factor to determine the average diameter of hollow microspheres, which can vary from 96 nm to 660 nm with the increase of the volume ratio of alcohol-water from 0 to 0.7. The silica wall thickness varies with the content and the hydrophobic chain length of the emulsifier, TEOS content, and the activity of the catalyst. The component of the soft template will affect the morphology of the silica wall. When the liquid paraffin is replaced by cyclohexane, hollow microspheres with fibrous mesoporous silica wall are fabricated. This work not only enriches the basic theory of interfacial polymerization in the emulsion system, but also provides ideas and methods for expanding the morphology and application of hollow silica microspheres.     

A new emulsion method to synthesize well-defined mesoporous particles

A new emulsion method for preparing ordered mesoporous materials with polymer PEG as the swelling agent has been explored in the present work. The synthesis conditions including the chain length and the PEG concentration, the duration of aging, the kind of emulsion, and the time when the swelling agents were added to the reaction system are discussed. The results show that with the advantage of the emulsion method, the nucleation and growth were controlled very well. The nicely spherical particles produced by the emulsion method were more uniform and less prone to agglomerate than those produced through the hydrothermal method. When different MW PEG were added as swelling agents, the pore size changed little: it was centered around 4 nm and had a narrow distribution. When different concentrations of PEG were applied, BET surface area, pore size, and pore volume changed. To summarize, in the formation of mesoporous materials, polymers such as PEG can not only control the pore size from 3 to 70 nm through variation of concentration, but also regulate the structures and improve the morphology of particles by the chain length of polymers. By adjusting the time of addition of the swelling agents, a poroshell mesoporous material was prepared. This method is particularly important for those applications that strictly require particle uniformity, such as chromatography separation.     

Preparation and characterization of film-forming raspberry-like polymer/silica nanocomposites via soap-free emulsion polymerization and the sol–gel process

Herein, we report on the synthesis of film-forming poly(styrene-co-butyl acrylate-co-acrylic acid)/SiO₂ [P(St-BA-AA)/SiO₂] nanocomposites by in situ formation of SiO₂ nanoparticles from TEOS via sol–gel process in the presence of poly(acrylic acid) (PAA)-functionalized poly(styrene-co-butyl acrylate) [P(St-BA)] particles fabricated by soap-free emulsion polymerization. The formed silica particles could be absorbed by polyacrylate chains on the surface of PAA-functionalized P(St-BA) particles; thus, raspberry-like polymer/silica nanocomposites would be obtained. Transmission electron microscopy, Fourier transform infrared spectroscopy, attenuated total reflectance infrared spectrum, ultraviolet–visible transmittance spectra, and thermogravimetric analysis were used to characterize the resulting composites. The results showed that the hybrid polymer/silica had a raspberry-like structure with silica nanoparticles anchored on the surface of polymer microspheres. The thermal, fire retardant, and mechanical properties and water resistance of the film were improved by incorporating silica nanoparticles, while the optical transmittance was seldom affected due to nanosized silica particles uniformly dispersed in the film.

单分散聚丙烯酸丁酯-二氧化硅核壳粒子的制备

近年来,有机-无机核壳材料因其具有可调的光、电、磁等特性而备受关注．无机物外壳可以增强粒子的热力学稳定性、机械强度和抗拉性能．高分子乳胶粒内核具有弹性,且易成膜,外部包覆无机物的乳胶粒可结合两者特性并产生协同效应．     

Synthesis and Characterization of Novel Amorphous Hybrid Silica Materials

Novel amorphous organic-inorganic hybrid silica materials have been prepared by the conventional sol-gel reaction of bis(gamma-trimethoxysilyl)propylamine (TMSPA) and tetraethyl orthosilicate (TEOS) in the presence of cetyltrimethylammonium bromide (CTABr) as a structure directing agent. The gelation of the hybrid silica gels took place faster as the TMSPA composition was higher. Infrared Spectroscopy (IR), Thermogravimetric Analysis (TGA), X-Ray Diffraction (XRD), and Scanning electron microscope (SEM) were used to characterize various hybrid materials. Nitrogen adsorption desorption isotherms at 77 K were used to determine the surface area, and average pore size. The hybrids were composed of macropores and a small amount of micropores. According to SEM photographs, the hybrids were composed of quite uniform aggregate of spherical particles with ca. 60 nm in diameter.     

Ultrafast enzyme immobilization over large-pore nanoscale mesoporous silica particles

By finely tuning the TEOS/P123 molar ratio of the octane/water/P123/TEOS quadruple emulsion system and by controlling the synthesis conditions, an ultrafine emulsion system was isolated, under the confinement of which, nanoscale silica particles with ordered large mesopores (approximately 13 nm) have been successfully constructed; the obtained mesoporous silica particles have an unusual ultrafast enzyme adsorption speed and the amount of enzyme that can be immobilized is larger than that of conventional mesoporous silica, which has potential applications in the fast separation of biomolecules.     

Influence of surfactant surface coverage and aging time on physical properties of silica nanoparticles

The experimental results on the influence of surfactant surface coverage and aging time on physical properties of silica nanoparticles were reported. The spherical silica nanoparticles have been synthesized using polyethylene glycol (PEG) as the surfactant and oil shale ash (OSA) as a new silica source. In order to identify the optimal condition for producing the best quality silica nanoparticles with the good dispersion and uniformity, the effects of surfactant surface coverage and aging time were investigated. It was found that the particle size and distribution of silica nanoparticles depend on the concentration of PEG in dispersion. At relatively low concentration, 0–2 wt.%, the existing PEG is not sufficient to prevent further growth of the initially formed silica nanoparticles, leading to large aggregates of silica particles. When the PEG concentration increases to 3 wt.%, self-assembled PEG layer on the surface stabilizes the initially formed silica nanoparticles and the silica particles with average diameter of 10 nm are uniformly distributed. With further increasing the concentration of PEG, the number of PEG aggregates increases and silica nanoparticles are mainly formed inside the entangled PEG chains, resulting in an observation of clusters of silica nanoparticles. Moreover, it was found that as the aging time increased, the shape of silica nanoparticles becomes regular and the particle size distribution becomes narrow.     

Aqueous Suspensions of Poly(ethylene Glycol)/Pyrocarbon/Fumed Silica

Aqueous suspensions of fumed silica and pyrocarbon/silica (CS) in the presence of dissolved poly(ethylene glycol) (PEG) were studied using (1)H NMR spectroscopy with freezing-out of bulk water and quantum chemical computations of the chemical shifts. The freezing effect for PEG/water is akin to that for low-molecular organics, as formation of solid phases of water (ice) and PEG occurs, and their mixture forms at the eutectic temperature. In the aqueous suspensions of fumed silica or CS, PEG molecules are localized at the solid-liquid interfaces and do not form the bulk solution even at large concentrations; however, the amount of bulk undisturbed water rises due to formation of the immobilized PEG layer. For such suspensions of silica or CS at a low amount of pyrocarbon (C(C)=4 wt%), there is a portion of the graph of the surface free energy (gamma(S)) increasing nearly linearly with the PEG concentration (C(PEG)); however, in the case of large C(C)=40 wt% in CS, a similar effect is not observed, as gamma(S) is maximal at low C(PEG)=0.1 wt%. Copyright 2001 Academic Press.     

Preparation of Spherical Hydrous Silica Oxide Particles under Acidic Condition via Sol-Gel Processing

Preparation of spherical hydrous silica oxide particles via sol-gel processing was rarely reported. In this study, spherical silica particles were obtained in TEOS/AcOEt/AcOH 50% aq. system. The combination of AcOEt and AcOH 50% aq. widened the spherical particle-forming region. Their size ranged from some ten micrometers to some hundreds micrometers. Hydrophilic molecules or powders like Rhodamine 6G and phosphorescent powders were encapsulated in the spherical particles.     

Control of shell thickness in silica-coating of Au nanoparticles and their X-ray imaging properties

This paper describes a performance of precise control of shell thickness in silica-coating of Au nanoparticles based on a sol-gel process, and an investigation into X-ray imaging properties for the silica-coated Au (Au/SiO(2)) particles. The Au nanoparticles with a size of 16.9±1.2 nm prepared through a conventional citrate reduction method were used as core particles. The Au nanoparticles were silica-coated with a sol-gel reaction using tetraethylorthosilicate (TEOS) as a silica source, sodium hydroxide (NaOH) as a catalyst, and (3-aminopropyl) trimethoxysilane (APMS) as a silane coupling agent. An increase in TEOS concentration resulted in an increase in shell thickness. Under certain concentrations of Au, H(2)O, NaOH, and APMS, the Au/SiO(2) particles with silica shell thickness of 6.0-61.0 nm were produced with varying TEOS concentration. Absorption peak wavelength of surface plasmon resonance of the Au/SiO(2) colloid solution depended on silica shell thickness, which agreed approximately with the predictions by Mie theory. The as-prepared colloid solution could be concentrated up to an Au concentration of 0.19 M with salting-out and centrifugation. The concentrated colloid solution showed an X-ray image with high contrast, and a computed tomography value for the colloid solution with an Au concentration of 0.129 M was achieved 1329.7±52.7 HU.