Thickening mechanism of associative polymers

Steady state viscosity and viscoelasticity of HMHEC solutions were studied. Viscosity increases with concentration due to a reinforcement of the micellar network. High shear rate viscosities are independent of temperature. Two relaxation processes were observed, the long one related to the lifetime of the hydrophobic junction and the short related to rapid Rouse-like relaxations of the free chains. When SDS is added, mixed micelles form that reinforce the network up to an optimum [SDS]/[HMHEC] ratio. Above this ratio, the micelles in excess isolate the polymer chains, the long relaxation process disappears and Rouse-like relaxations occur, corresponding to rapid movements of free chains.     

THE EFFECTS OF MIXED MICELLES OF SURFACTANTS ON POLYMERIZATION OF ACRYLAMIDE

The polymerization of acrylamide in mixed micellar solutions of surfactants, initiated by NaHSO₃ has been studied at 20 and 3Q° C with time variable method of thermokinetics for 1. 5-order reaction. The results indicate that the mixed micellar systems of cationic or anionic with zwitterionic surfactants (SLS/ CTAB, SLS/ TTAB, SLS/ SDS) and cationic with nonionic surfactants (Brij 357sol; CTAB, Bri-J35/TTAB, Brij35/ DTAB) have catalytic effect on the polymerization in the order, at 20° C. SLS/ SDS SLS/ TTAB SLS/ CTAB Brij35/ CTAB at 30° C SLS/ SDS SLS/ TTAB≈ / CTAB Bri-j35/ DTAB= sBrij35/ TTAB as Brij35/ CTAB, while Brij35/ SDS mixed micellar system has inhibition. These effects are attributed to the effect of the Stern layer of mixed micelles on the step of initiator (HSOT) to form free radical.     

Hydrophobized polysaccharide macrogel formed by addition of surfactants

Solution properties of an aqueous mixture of cholesterol-bearing pullulan (CHP) and an ionic surfactant, sodium dodecyl sulfate (SDS) or dodecyltrimethylammonium chloride (DoTAC), were studied. The mixture forms gel or sol depending on the polymer-surfactant composition. Because the unmodified pullulan/surfactant/water mixture does not show any gel formation at all over the composition range studied, the hydrophobic cholesterol moieties play an essential and important role in the gel formation. The phase behavior could be interpreted by formation of mixed micelles between cholesterol moieties of CHP and the surfactants. This was supported also by SAXS studies in the sol region. Rheological measurements of the gel showed that viscoelastic response of the CHP/SDS gel was controlled by at least two different processes with shorter and longer relaxation times. This was different from previously reported results for a system such as hydrophobically modified (hydroxyethyl)cellulose (HMHEC) and SDS.     

非离子表面活性剂Brij 30诱导离子液体型表面活性剂C16imC8Br蠕虫状胶束向凝胶的转变

Wormlike micelles and low-molecular-weight hydrogels are composed of three-dimensional networks that endow them with viscoelasticity, but their viscoelastic properties are markedly different. The viscosity of wormlike micelles is attributed to a transient network, while that of gels is due to a stable network. Under certain conditions, wormlike micelles can undergo transition to gels with an increase in the density of the network. In our previous study, we found that the wormlike micelle formed by the ionic liquid-type surfactant 1-hexadecyl-3-octyl imidazolium bromide ([C₁₆imC₈]Br) without any additive has high viscoelasticity. The inclusion of a nonionic surfactant polyoxyethylene lauryl ether (Brij 30) is expected to enhance the viscoelasticity of [C₁₆imC₈]Br wormlike micelles via electrostatic shielding and strong hydrophobic interactions, which may be the driving factor for the wormlike micelle-to-gel structural transition. The morphology and viscoelasticity of [C₁₆imC₈]Br wormlike micelles with Brij 30 were studied as a function of concentration by rheological measurements and freeze-fracture transmission electron microscopy. The thermal stability and gel-sol transition temperature of the Brij 30/[C₁₆imC₈]Br gels were studied using rheology. The interaction between Brij 30 and [C₁₆imC₈]Br was studied by zeta potential measurements and nuclear magnetic resonance (NMR) spectroscopy. Upon the inclusion of Brij 30 into the [C₁₆imC₈]Br wormlike micelles, the viscoelasticity of the Brij 30/[C₁₆imC₈]Br samples first increased and then decreased with an increase in the Brij 30 concentration, at different initial concentrations of [C₁₆imC₈]Br. At a certain Brij 30 concentration, the Brij 30/[C₁₆imC₈]Br samples rheologically behaved as a gel. The maximum viscoelasticity of the [C₁₆imC₈]Br (4.06% (w))/Brij 30 gel was observed at a Brij 30/[C₁₆imC₈]Br molar ratio of 4.55. The viscoelasticity of the Brij 30/[C₁₆imC₈]Br gels was positively correlated with the activation energy of the gels. The gel-sol transition temperature of the Brij 30/[C₁₆imC₈]Br gels also increased first and then decreased with an increase in the Brij 30 concentration. The highest gel-sol transition temperature of the Brij 30/[C₁₆imC₈]Br (4.06% (w)) gel was observed at a Brij 30/[C₁₆imC₈]Br molar ratio of 2.93. The Brij 30 concentration had a notable impact on the viscoelasticity, thermal stability, and gel-sol transition temperature of the Brij 30/[C₁₆imC₈]Br gels. The zeta potential and ¹H NMR measurements revealed that the neutral Brij 30 molecules are inserted into the palisade layer of the [C₁₆imC₈]Br wormlike micelles via hydrophobic interactions. This decreased the electrostatic repulsion between the [C₁₆imC₈]Br headgroups, which in turn induced the rapid growth of wormlike micelles and the formation of a stiffer network structure. Finally, the wormlike micelles underwent a structural transition to gels. The obtained results would aid in better understanding the relationship between wormlike micelles and gels, and may be of potential value for industrial and technological applications.     

THE EFFECT OF MIXED MICELLES OF SURFACTANTS ON THE ALKALINE HYDROLYSIS OF ESTERS

The alkaline hydrolysis of aromatic and normal aliphatic acid esters have been studied at 25°C In mixed micellar solution of surfactants (Brij35—SDS, Brij35 — DTAB, Brij35—TTAB.Brij35-CTAB. Triton X—100 —CTAB, Triton X— 100 —SDS) with UV spectrophotometry and the method of thermokinetics The critical mice liar concentrations of the corresponding systems have also been measured with UV spectrophotometry in this paper. K_jnln micellar pseudo-phase has been calculated- The ratios of ki.to ki.for all mixed micellar systems Investigated are less than 1. The results indicate that these reactions are inhibited by the mixed micelles and the mixed micelles exhibit a greater effect of Inhibition on the reactions than those do In corresponding single ones. The reason for this is that the micropolarity of the compact Stern layer of mixed micelle is lower, and the micro viscidity Is higher. The Inhibition effect! also depend on the hydrophobic chain length of the surfactants and the hydrophobicity of the substrate.     

Nonionic surfactant and temperature effects on the viscosity of hydrophobically modified hydroxyethyl cellulose solutions

Nonionic surfactant and temperature effects on the viscosity of hydrophobically modified hydroxyethyl cellulose (HMHEC) solutions are investigated experimentally. Weak shear thickening at intermediate shear rates takes place for HMHEC at moderate concentrations and becomes more significant at lower temperatures. While this amphiphilic polymer in surfactant-free solution does not turn turbid by heating to 95 degrees C, its mixture with nonionic surfactant shows a lower cloud point temperature than does a pure surfactant solution. For some mixture cases, phase separation takes place at temperatures as low as 2 degrees C. The drop of cloud point temperature is attributed to an additional attractive interaction between mixed micelles via chain bridging. With increasing temperature, the viscosity of an HMHEC-surfactant mixture in aqueous solution first decreases but then rises considerably until around the cloud point. The observed viscosity increase can be explained by the interchain association because of micellar aggregation.     

Effects of surfactant micelles on solubilization and DPPH radical scavenging activity of Rutin

The interaction of the antioxidant Rutin with the radical DPPH (2,2-diphenyl-1-picrylhydrazyl) in presence of cationic (CTAB, TTAB, DTAB), non-ionic (Brij78, Brij58, Brij35), anionic (SDS) and mixed surfactant systems (CTAB-Brij58, DTAB-Brij35, SDS-Brij35) has been followed by spectrophotometric and tensiometric methods to evaluate the DPPH radical scavenging activity (RSA) of Rutin in these model self-assembled structures. The results show that the solubilization capacity of various single surfactant systems for both DPPH as well as Rutin followed the order cationics > non-ionics > anionic. The radical scavenging activity of Rutin in the solubilized form was higher within ionic micelles than in non-ionic micelles. However, the antioxidant exhibited enhanced activity for the radical in mixed cationic-non-ionic micelles compared with any of the single component micelles. In contrast, anionic-non-ionic mixed micelles modulated the activity of Rutin in-between that seen for pure anionic and non-ionic micelles only.     

Separation and mechanism elucidation for six structure-like matrine-type alkaloids by micellar liquid chromatography

A mixed micellar liquid chromatography (MLC) method, the mobile phase consisting of anionic surfactant SDS and nonionic surfactant Brij35, was firstly developed for the separation and determination of six structure-like matrine-type alkaloids, including matrine, oxymatrine, sophocarpine, oxysophocarpine, sophoridine, and oxysophoridine. The factors influencing the resolution of the six alkaloids were systematically investigated and optimized, including the micellar composition and concentration, column temperature, the type and amount of organic solvent, and the pH values in the mobile phases. Under the optimized separation conditions, the six matrine-type alkaloids could be easily isocratically eluted with a baseline separation within 22 min. Under the designated conditions (SDS concentration from 10 to 50 mM, Brij35 from 5 to 30 mM, pH 3 and 5% 1-propanol), the hydrophobic selectivity was negatively correlated with the concentration of Brij35 but not with SDS. The functional group selectivity of the carbonyl group, double bond, and diastereomers, all decreased with the increase in percentage of SDS in the mixed micellar phase, because the strong electrostatic force masks other molecular forces which can discriminate the retention of the analytes. Therefore, such a combination in surfactants of MLC is a powerful strategy to increase the selectivity by adjusting the balance among the various molecular interaction forces influencing analytes' retention. Finally, the developed method was successfully used to separate and determine the contents of main alkaloids in Sophora medicinal plants, S. flavescens Ait. In summary, the mixed MLC is a valuable approach to separate and determine the structure-like multi-component natural samples.     

Optimization of separation and migration behavior of chloropyridines in micellar electrokinetic chromatography

The separation and migration behavior of pyridine and eight chloropyridines, including three monochloropyridines, four dichloropyridines, and 2,3,5-trichloropyridine were investigated by micellar electrokinetic chromatography using either sodium dodecyl sulfate (SDS) as an anionic surfactant or SDS-Brij 35 mixed micelles. Various parameters such as buffer pH, SDS concentration, Brij 35 concentration and methanol content that affect the separation were optimized. Complete separation of these chloropyridines was optimally achieved with a phosphate buffer containing SDS (30 mM) and methanol (10%, v/v) at pH 7.0. The resolution and selectivity of analytes could be considerably affected by the addition of methanol and/or Brij 35 to the background electrolyte. The migration order of these chloropyridines depends primarily on their hydrophobicity. However, electrostatic interactions may also play a significant role in the determination of the migration order of the positional isomers of chloropyridines.     

Investigation of solvent effects in capillary electrophoresis for the separation of biological porphyrin methyl esters

The effects of organic solvents on the capillary electrophoresis (CE) separation of a number of important biological porphyrin methyl esters - six weakly basic, hydrophobic cyclic tetrapyrroles possessing two and four to eight methyl ester groups around the periphery of the porphyrin ring - were investigated in the mode of micellar electrokinetic chromatography (MEKC), microemulsion electrokinetic chromatography (MEEKC), and nonaqueous CE. In aqueous MEKC, partial separation of the six neutral porphyrin methyl esters was obtained with an organic modifier (acetonitrile) in the concentration range between 20 and 40%, in which sodium dodecyl sulfate (SDS) molecules might be present in the form of SDS micelles and/or SDS micelle-like aggregates. Relatively stable SDS micelles can be formed in nonaqueous MEKC using formamide as the separation medium, but the separation of the target analytes remained unsatisfactory. Improved resolution of all six porphyrin methyl esters was obtained using MEEKC with the running buffer consisting of 0.8% w/w n-heptane (oil phase), 2.25% w/w SDS and 1.0% w/w Brij 35 (mixed surfactant), 6.6% w/w 1-butanol (cosurfactant), and 30% v/v 2-propanol (second cosurfactant), but reproducibility in terms of peak areas for certain porphyrins (especially uroporphyrin I octamethyl ester) was found to be very poor. Best separation performances were achieved with nonaqueous CE separations in which the weakly basic porphyrin methyl esters were protonated under strongly acidic conditions (e.g., using 10 mM perchloric acid) in mixed organic solvents. For example, using a 50:50 mixture of methanol and acetonitrile as the separation medium, baseline separation of all six (positively charged) porphyrin methyl esters can be obtained within 3 min and the average precision (RSD, N = 13) in terms of migration time and peak area were 0.55 and 2.16%, respectively.     

Separation and selectivity in micellar electrokinetic chromatography using sodium dodecyl sulfate micelles or Tween 20-modified mixed micelles

The separation and selectivity of eight aromatic compounds ranging from hydrophilic to hydrophobic properties in micellar electrokinetic chromatography (MEKC) using sodium dodecyl sulfate (SDS) micelles or Tween 20-modified mixed micelles were investigated. The effect of different operation conditions such as SDS and Tween 20 modifier surfactant concentration, buffer pH, and applied voltage was studied. The resolution and selectivity of analytes could be markedly affected by changing the SDS micelle concentration or Tween 20 content in the mixed micelles. Applied voltage and pH of running buffers were used mainly to shorten the separation time. Complete separation of eight analytes could be achieved with an appropriate choice of the concentration of SDS micelles or Tween 20-modified mixed micelles. Quicker elution and better precision could be obtained with SDS-Tween 20 mixed micelles than with SDS micelles. The mechanisms that migration order of those analytes was mainly based on their structures and solute-micelle interactions, including hydrophobic, electrostatic, and hydrogen bonding interactions, were discussed.     

Influence of alkoxyethanols on the mixed micelle formation by hexadecyltrimethylammonium bromide and tetradecyltrimethylammonium bromide surfactant mixtures

 The conductances of hexadecyltrimethylammonium bromide (HTAB) and tetradecyltrimethylammonium bromide (TTAB) mixtures over the entire mole fraction range of HTAB were measured in aqueous binary mixtures of ethylene glycol monomethyl ether, monoethyl ether, and monobutyl ether, and of diethylene glycol monomethyl ether and monoethyl ether containing 10–30 wt% additive in their respective binary mixtures at 30 °C. Each conductivity curve showed a single break over the whole mole fraction range of HTAB–TTAB mixtures. From the break in the conductivity curve, various micellar parameters were calculated and the results were discussed with respect to the alkoxyethanol's additive effect on the mixed micelle formation. The micellar parameters of HTAB, TTAB, and of their mixtures showed a strong dependence both on the amount as well as on the number of repeating units in the presence of ethylene glycol derivatives, whereas a significant dependence only on the amount of additive was observed in aqueous diethylene glycol derivatives. The results in the former case were attributed to the hydrophobic hydration of the mixed micelles by the ethylene glycol derivatives, which showed a large dependence on the increase in the alkyl chain length of the additive. The hydrophobic hydration was considerably reduced in the case of diethylene glycol derivatives owing to the presence of an extra ether oxygen. An evaluation of the nonideality in the HTAB–TTAB mixtures revealed that in spite of the strong hydrophobic hydration of the HTAB–TTAB mixtures by the alkoxyethanols, the mixed micelles remain almost free from the additive molecules. Received: 11 January 2000/Accepted: 14 April 2000     

Solubilization of Aliphatic Carboxylic Acids (C3-C6) by Sodium Dodecyl Sulfate and Brij 35 Micellar Pseudophases

The apparent dissociation constants of 1-propanoic, 1-butanoic, 1-pentanoic and 1-hexanoic acids were obtained for the first time in Brij 35 micellar solutions with concentration from 0.03 to 0.20 mol⋅L⁻¹ and sodium dodecyl sulfate (SDS) micellar solutions with concentrations from 0.01 to 0.30 mol⋅L⁻¹. A pronounced effect of Brij 35 micelles on the acid-base properties of aliphatic acids was observed. The binding constants, K _b, of carboxylic acids to micellar pseudophases of SDS and Brij 35 were estimated within the framework of the pseudophase model. The dependences of Gibbs energies of transfer from water to the micellar pseudophases were constructed, and Gibbs energies were evaluated for methylene and carboxylic group transfers into Brij 35 and SDS micelles. Comparison of the Gibbs energies of methylene group transfer from water to Brij 35 and SDS suggests that the mechanisms of hydrocarbon group transfer into the core of nonionic and anionic micelles involving the same monomer hydrophobic tail length are similar.     

Synergistic effects in flows of mixtures of wormlike micelles and hydroxyethyl celluloses with or without hydrophobic modifications

This work presents experimental results on simple shear and porous media flow of aqueous solutions of two hydroxyethyl celluloses (HEC) and two hydrophobically modified hydroxyethyl celluloses (HMHEC) with different molecular weights. Mixtures of these polymers with a cationic surfactant, cetyltrimethylammonium p-toluenesulfonate (CTAT) were also studied. Emphasis was given to the range of surfactant concentrations in which wormlike micelles are formed. The presence of hydrophobic groups, the effect of the molecular weight of the polymers, the surfactant and polymer concentrations, and the effect of the flow field type (simple shear versus porous media flow) were the most important variables studied. The results show that the shear viscosity of HEC/CTAT solutions is higher than the viscosities of surfactant and polymer solutions at the same concentrations, but surface tension measurements indicate that no complex formation occurs between CTAT and HEC. On the other hand, a complex driven by hydrophobic interactions was detected by surface tension measurements between CTAT and HMHEC. In this case, the viscosity of the mixture increases significantly more (up to four orders of magnitude at high CTAT concentrations) in comparison with HEC/CTAT aqueous solutions. Increments in the molecular weight of the polymers increase the interaction with CTAT and the shear viscosity of the solution, but make phase separation more feasible. In porous media flow, the polymer/CTAT mixtures exhibited higher apparent viscosities than in simple shear flows. This result suggests that the extensional component of the flow field in porous media flows leads to a stronger interaction between the polymer and the wormlike micelles, probably as a consequence of change of conformation and growth of the micelles.     

Self aggregation of binary mixtures of sodium dodecyl sulfate and polyoxyethylene alkyl ethers in aqueous solution

The mixed micelles of sodium dodecyl sulphate (SDS) with Brij35 and Brij 97 were studied separately by fluorescence measurement using pyrene as fluorescent probe. In the range of 0–1.0 mole fraction (X) of added SDS to Brij solutions, the cmc value of the mixed micelles varies from 0.085 to 8 mmol with Brij 35 and 0.04 to 8 mmol with Brij 97. The aggregation number also changes. A measure of the stability of mixed micelles is also presented. The interaction parameter ₁₂ and the chain–chain contribution parameter (B₁) are extracted from the analysis of the results. This parameter B₁ is related to the standard free energy change associated with the introduction of one ionic species into a nonionic micelle coupled with the release of one nonionic species from the micelle. The clouding behaviour of Brij 97 in the presence of SDS was investigated and the associated thermodynamic parameters of clouding were generated and discussed.     

Molecular interaction of Congo Red with conventional and cationic gemini surfactants

Interaction of tetradecyltrimethylammonium bromide (TTAB), octylophenylpolyoxyethylene ether (TX-100), sodium dodecylsulfate (SDS), N,N′-ditetradecyl-N,N,N′,N′-tetramethyl-N,N′-butanediyl-diammonium dibromide (14,4,14) and N,N′-didodecyl-N,N,N′,N′-tetramethyl-N,N′-butanediyl-diammonium dibromide (12,4,12) with an anionic diazo dye, Congo Red, was investigated using conductometry, spectroscopy, tensiometry, and pulsed field gradient NMR (PFG-NMR). The formation of dye-surfactant ion pairs, their small mixed aggregates (below the critical micelle concentration (CMC) of these surfactants) and surfactant micelles were detected successfully. Above the CMC, the dye reverted to its monomeric state and solubilized in the micelles. Job's method was used to determine the stoichiometric ratio of dye and surfactant in ion pairs and revealed the formation of more hydrophile ion pairs for geminis compared to their conventional analogs. Quantitative results obtained from tensiometry indicated the existence of considerable synergism for cationic surfactants and antagonism for anionic SDS. In addition, the synergism observed for TX-100 revealed the effect of π-π stacking and hydrophobic forces on ion pair and mixed micelle formation. The increase of dye-surfactant interactions by increasing the electrical charge and chain length of cationic surfactants confirmed the importance of both electrostatic and hydrophobic forces in binary dye/surfactant systems. The hydrodynamic radii of the micelles were determined by self-diffusion coefficient measurements. The average size of the cationic and nonionic micelles increased in the presence of CR molecules.     

Clouding and phase behavior of nonionic surfactants in hydrophobically modified hydroxyethyl cellulose solutions

Clouding phenomena and phase behaviors of two nonionic surfactants, Triton X-114 and Triton X-100, in the presence of either hydroxyethyl cellulose (HEC) or its hydrophobically modified counterpart (HMHEC) were experimentally studied. Compared with HEC, HMHEC was found to have a stronger effect on lowering the cloud point temperature of a nonionic surfactant at low concentrations. The difference in clouding behavior can be attributed to different kinds of molecular interactions. Depletion flocculation is the underlying mechanism in the case of HEC, while the chain-bridging effect is responsible for the large decrease of cloud point for HMHEC. Composition analyses for the formed macroscopic phases were carried out to provide support for associative phase separation for the case of HMHEC, in contrast to segregative phase separation for HEC. An interesting three-phase-separation phenomenon was reported in some HMHEC/Triton X-100 mixtures at high surfactant concentrations.     

Analysis of clindamycin by micellar electrokinetic chromatography with a mixed micellar system.

This study details the development and validation of an optimized method with micellar electrokinetic chromatography for the analysis of clindamycin. The method uses a mixed micellar phase containing anionic sodium dodecylsulfate (SDS) and non ionic Brij 35 on an untreated fused-silica capillary. The influences of buffer concentration, pH, SDS, Brij 35 and organic modifier were investigated. Special attention was given to the role of the non ionic Brij 35 in the mixed micellar system. Optimization with a central composite design resulted in optimal separation conditions: background electrolyte containing 25 mM sodium tetraborate pH 7.75, 90 mM SDS, 14 mM Brij 35 and 21% acetonitrile. The applied voltage was 15 kV and the capillary temperature 15 degrees C. The method was robust and gave good linearity and repeatability. The limits of detection and quantitation were 0.05 and 0.15%, respectively, relative to a 2.5 mg/ml clindamycin solution. Two commercial bulk products were analysed with this system.     

混合表面活性剂在非极性溶剂中的聚集行为

表面活性剂在非极性溶剂中的聚集行为比在水溶液中复杂得多. 水溶液中表面活性剂有一明确的临界胶束浓度(CMC),而在非极性溶剂中至今对CM C概念仍有怀疑^[1], 但已有多种手段如染料增溶法、水增溶法、光散射法、荧光偏振、紫外和核磁共振谱等证实并测定了非极性溶剂中 CMC 的存在^[1～5]. 表面活性剂在非极性溶剂中以非离子化状态存在, 其缔合主要靠两亲分子之间的偶极-偶极以及离子对相互作用, 那么在一种表面活性剂溶液中加入另一种表面活性剂, 即表面活性剂的复配, 必然对其聚集行为产生重大影响, 但迄今为止, 尚未见关于混合表面活性剂在非极性溶剂中聚集行为的报道. 本文采用碘光谱法和水增溶法测定了阴离子表面活性剂AOT 和非离子表面活性剂 Brij30 混合后在正庚烷中形成反胶束的 CMC, 以期考察表面活性剂的复配对其聚集行为的影响。     

Oil-in-water emulsions stabilized by hydrophobically modified hydroxyethyl cellulose: adsorption and thickening effect

The preparation and stability of oil-in-water emulsions stabilized by hydrophobically modified hydroxyethyl cellulose (HMHEC) were investigated. The rheological measurements of aqueous HMHEC were studied. It was found that HMHEC showed much better thickening ability than the parent (HEC) from which it was derived, which is caused by the association of the hydrophobic alkyl chains, which are absent in HEC. The oscillatory experimental results of the emulsions showed that at higher concentrations, HMHEC could form an elastic gel, which has good thixotropic properties. The stability and droplet size distribution were investigated by visual observation, photomicrograph and a laser-scattering particle size distribution analyzer. The adsorption of HMHEC at the oil-water interface and the surface of emulsion droplets due to the penetration of the alkyl chains in HMHEC into the oil phase were confirmed by visual observation, the interfacial tension method and an in situ environmental scanning electron microscope (ESEM). The stability of emulsions prepared using HMHEC is based on both an associative thickening mechanism caused by alkyl chains in HMHEC and the adsorption of HMHEC at the oil-water interface, which can form a solid film preventing coalescence of the droplets.