Fabrication of two biomimetic superhydrophobic polymeric surfaces

Two biomimetic superhydrophobic polymeric surfaces were obtained by a simple approach under ambient atmosphere. Water and ethanol were used as the nonsolvents in the method of phase separation in different systems. The influences of various factors in the process were investigated. Both of the as-prepared films showed excellent superhydrophobicity, depending on the high contact angle and the low contact angle hysteresis. Moreover, the classic and a new modified Cassie-Baxter relation were used on the polystyrene and poly-α-methyl styrene films to confirm the superhydrophobic performance.     

Fabrication and characterization of a cotton candy like surface with superhydrophobicity

Superhydrophobic thin films were prepared on glass by air-brushing the in situ polymerization compositions of D₅/SiO₂. The wettability and morphology were investigated by contact angle measurement and scanning electron microscopy. The most superhydrophobic samples prepared had a static water contact angle of 157° for a 5 μl droplet and a sliding angle of ∼1° for 10 μl droplet. Thermal stability analysis showed that the surface maintained superhydrophobic at temperature up to 450 °C. Air trapping and capillary force on superhydrophobic behavior were evaluated.     

Transparent Superhydrophobic silica coatings on glass by sol-gel method

Wetting behavior of solid surfaces is a key concern in our daily life as well as in engineering and science. In the present study, we demonstrate a simple dip coating method for the preparation of Thermally stable, transparent superhydrophobic silica films on glass substrates at room temperature by sol-gel process. The coating alcosol was prepared by keeping the molar ratio of methyltriethoxysilane (MTES), trimethylmethoxysilane (TMMS), methanol (MeOH), water (H₂O) constant at 1:0.09:12.71:3.58, respectively with 13 M NH₄OH throughout the experiments and the films were prepared with different deposition time varied from 5 to 25 h. In order to improve the hydrophobicity of as deposited silica films, the films were derivatized with 10% trimethylchlorosilane (TMCS) as a silylating agent in hexane solvent for 24 h. Enhancement in wetting behavior was observed for surface derivatized silica films which showed a maximum static water contact angle (172°) and minimum sliding angle (2°) for 25 h of deposition time. The superhydrophobic silica films retained their superhydrophobicity up to a temperature of 550 °C. The silica films were characterized by field emission scanning electron microscopy (FE-SEM), surface profilometer, Fourier transform infrared (FT-IR) spectroscopy, thermo-gravimetric and differential thermal analysis (TG-DTA), percentage of optical transmission, water contact angle measurements. The imperviousness behavior of the films was tested with various acids.     

Fabrication of superhydrophobic silica-based surfaces with high transmittance by using tetraethoxysilane precursor and different polymeric species

The preparation of superhydrophobic silica-based surfaces via the sol-gel process through the addition of different polymeric species into the precursor solution was done in this study. The surface roughness of the films was obtained by removing the organic polymer at a high temperature, and then the hydrophobic groups were bonded onto the films with a monolayer by chemical reaction with hexamethyldisilazane (HMDS). The characteristic properties of the as-prepared films were analyzed by contact angle measurements, scanning electron microscopy (SEM), atomic force microscopy (AFM), nitrogen adsorption/desorption, and UV-vis scanning spectrophotometer. The experimental results revealed that the superhydrophobic thin films with high transmittance could easily be prepared using polypropylene (PPG), polyethylene (PEG), and poly(vinylpyrrolidone) (PVP). Surface roughness and pore size were enhanced using PPG polymeric species. The distribution of pore size was from the microporous to the mesoporous and marcoporous regions. In addition, the contact angles of the rough surfaces prepared at 500 °C without modification of HMDS were smaller than 5° but larger than 156° after modified by HMDS.     

Preparation of transparent BN films with superhydrophobic surface

A novel approach was investigated to obtain the superhydrophobicity on surfaces of boron nitride films. In this method boron nitride films were deposited firstly on Si(1 0 0) and quartz substrate using a radio frequency (RF) magnetron sputtering system, and then using CF₄ plasma treatment, the topmost surface area can be modified systematically. The results have shown that the water contact angle on such surfaces can be tuned from 67° to 159°. The films were observed to be uniform. The surfaces of films consist of micro-features, which were confirmed by Atomic Force Micrograph. The chemical bond states of the films were determined by Fourier Transform Infrared (FTIR) Spectroscopy, which indicate the dominance of B-N binding. According to the X-ray Photoelectron Spectroscopy analysis, the surface of film is mainly in BN phase. The micro-feature induced surface roughness is responsible for the observed superhydrophobic nature. The water contact angles measured on these surfaces can be modeled by the Cassie's formulation.     

Superhydrophobicity of polytetrafluoroethylene thin film fabricated by pulsed laser deposition

Superhydrophobic polytetrafluoroethylene (PTFE) thin films were obtained by pulsed laser deposition (PLD) technique carried out with KrF excimer laser (λ = 248 nm) of about 1 J/cm² at a pressure of 1.33 Pa. The samples exhibit high water contact angle of about 170° and the sliding angle smaller than 2°. From studying the surface morphology of the prepared films, it is believed that the nano-scale surface roughness has enhanced the hydrophobic property of the PTFE. The increase of trapping air and reducing liquid-solid contact area due to the rough surface, as suggested by the Cassie-Baxter's model, should be responsible for superhydrophobicity of the PLD prepared films. This study thus provides a convenient one-step method without using wet-process to produce a superhydrophobic surface with good self-cleaning properties.     

Preliminary study on different technological tools and polymeric materials towards superhydrophobic surfaces for automotive applications

Nature-inspired fabrication of micro-structured superhydrophobic plastic film was aimed in this work in order to achieve smart materials with self-cleaning properties. Replicas of silicon masters were fabricated from different mixtures of base elements and by different processes. Corresponding microstructures were investigated by contact angle measurements, scanning electron microscopy and spectrophotometric analysis. Independently of the technology employed, the obtained films exhibited high contact angle value (larger than 150°), but while the acrylic polymers presented strong demoulding drawbacks, the polydimethylsiloxane (PDMS) films had good properties in terms of both contact angle and optical transparency. The results showed that most of the patterns realized by replica moulding and hot-embossing (on PDMS and polypropylene (PP), respectively) produced superhydrophobic self-cleaning surfaces.     

Superhydrophobic hierarchical surfaces fabricated by anodizing of oblique angle deposited Al-Nb alloy columnar films

A combined process of oblique angle magnetron sputtering and anodizing has been developed to tailor superhydrophobic surfaces with hierarchical morphology. Isolated submicron columns of single-phase Al-Nb alloys are deposited by magnetron sputtering at several oblique deposition angles on a scalloped substrate surface, with the gaps between columns increasing with an increase in the deposition angle from 70° to 110°. Then, the columnar films have been anodized in hot phosphate-glycerol electrolyte to form a nanoporous anodic oxide layer on each column. Such surfaces with submicron-/nano-porous structure have been coated with a fluoroalkyl phosphate layer to reduce the surface energy. The porous surface before coating is superhydrophilic with a contact angle for water is less than 10°, while after coating the contact angles are larger than 150°, being superhydrophobic. The beneficial effect of dual-scale porosity to enhance the water repellency is found from the comparison of the contact angles of the submicron columnar films with and without nanoporous oxide layers. The larger submicron gaps between columns are also preferable to increase the water repellency.     

One-step electrodeposition process to fabricate cathodic superhydrophobic surface

In this work, a rapid one-step process is developed to fabricate superhydrophobic cathodic surface by electrodepositing copper plate in an electrolyte solution containing manganese chloride (MnCl₂·4H₂O), myristic acid (CH₃(CH₂)₁₂COOH) and ethanol. The superhydrophobic surfaces were characterized by means of scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The shortest electrolysis time for fabricating a superhydrophobic surface is about 1 min, the measured maximum contact angle is 163° and rolling angle is less than 3°. Furthermore, this method can be easily extended to other conductive materials. The approach is time-saving and cheap, and it is supposed to have a promising future in industrial fields.     

Superhydrophobic surfaces based on dandelion-like ZnO microspheres

This study presents a simple method to fabricate superhydrophobic surface based on ZnO nanoneedles. ZnO nanoneedles had been constructed on zinc layers by immersing in an aqueous NH₄OH solution at 80 °C. The ZnO films were characterized by X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy. The ZnO films exhibited excellent superhydrophilicity (contact angle for water was 0°), while they changed wettability to superhydrophobicity with a water contact angle greater than 150° after further chemical modification with n-dodecanoic acid. The procedure reported here only needs readily available reagents and laboratory equipments, which can be applied to various substrates of any size and shape.     

Preparation and properties of ZnS superhydrophobic surface with hierarchical structure

A novel ZnS hierarchical structure composed of nanorod arrays with branched nanosheets and nanowires grown on their upside walls, was synthesized over Au-coated silicon substrate via chemical vapor deposition technique. Contact angle and sliding angle of this hierarchical film with no surface modification were measured to be about 153.8° and 9.1° for 5 μl water droplets. Self-cleaning behavior and dynamic water-repelling performance were clearly demonstrated. In addition, electrowetting transition phenomenon from superhydrophobic to hydrophilic state happened when a critical bias ∼7.0 V was applied. Below this threshold voltage, the contact angle change is little. This work for the first time reports the creation of ZnS superhydrophobic surface and could enrich its research field as surface functional materials.     

Semiconductor supported biomimetic superhydrophobic gold surfaces by the galvanic exchange reaction

Highly stable gold micro-nanostructures with various morphologies were fabricated using a galvanic exchange reaction under different conditions, such as, concentration of gold salt, illumination, solution temperature, ultrasonication, or addition of surfactants. After modification of the gold films with n-dodecanethiol, superhydrophobic surface (contact angle 165°) similar to the lotus leaf was obtained. In addition, the mechanism for superhydrophobic property was discussed.     

Preparation of superhydrophobic films on titanium as effective corrosion barriers

Stable superhydrophobic films were prepared on the electrochemical oxidized titania/titanium substrate by a simple immersion technique into a methanol solution of hydrolyzed 1H,1H,2H,2H-perfluorooctyltriethoxysilane [CF₃(CF₂)₅(CH₂)₂Si(OCH₂CH₃)₃, PTES] for 1 h at room temperature followed by a short annealing at 140 °C in air for 1 h. The surface morphologies and chemical composition of the film were characterized by means of water contact angle (CA), field emission scanning electron microscopy (FESEM), atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS). The water contact angle on the surface of this film was measured to be as high as 160°. SEM images showed that the resulting surfaces exhibited special hierarchical structure. The special hierarchical structure along with the low surface energy leads to the high surface superhydrophobicity. The corrosion resistance ability and durance property of the superhydrophobic film in 3.5 wt.% NaCl solution was evaluated by the electrochemical impedance spectroscopy (EIS). The anticorrosion properties of the superhydrophobic film are compared to those of unmodified pure titanium and titania/titanium substrates. The results showed that the superhydrophobic film provides an effective corrosion resistant coating for the titanium metal even with immersion periods up to 90 d in the 3.5 wt.% NaCl solution, pointing to promising future applications.     

Wetting and superhydrophobic properties of PECVD grown hydrocarbon and fluorinated-hydrocarbon coatings

Wetting characteristics of micro-nanorough substrates of aluminum and smooth silicon substrates have been studied and compared by depositing hydrocarbon and fluorinated-hydrocarbon coatings via plasma enhanced chemical vapor deposition (PECVD) technique using a mixture of Ar, CH₄ and C₂F₆ gases. The water contact angles on the hydrocarbon and fluorinated-hydrocarbon coatings deposited on silicon substrates were found to be 72° and 105°, respectively. However, the micro-nanorough aluminum substrates demonstrated superhydrophobic properties upon coatings with fluorinated-hydrocarbon providing a water contact angle of ∼165° and contact angle hysteresis below 2° with water drops rolling off from those surfaces while the same substrates showed contact angle of 135° with water drops sticking on those surfaces. The superhydrophobic properties is due to the high fluorine content in the fluorinated-hydrocarbon coatings of ∼36 at.%, as investigated by X-ray photoelectron spectroscopy (XPS), by lowering the surface energy of the micro-nanorough aluminum substrates.     

Superhydrophobic cotton fabric fabricated by electrostatic assembly of silica nanoparticles and its remarkable buoyancy

Highly hydrophilic cotton fabrics were rendered superhydrophobic via electrostatic layer-by-layer assembly of polyelectrolyte/silica nanoparticle multilayers on cotton fibers, followed with a fluoroalkylsilane treatment. The surface morphology of the silica nanoparticle-coated fibers, which results in the variety of the hydrophobicity, can be tailored by controlling the multilayer number. Although with the static contact angle larger than 150°, in the case of 1 or 3 multilayers, the fabrics showed sticky property with a high contact angle hysteresis (>45°). For the cotton fabrics assembled with 5 multilayers or more, slippery superhydrophobicity with a contact angle hysteresis lower than 10° was achieved. The buoyancy of the superhydrophobic fabric was examined by using a miniature boat made with the fabric. The superhydrophobic fabric boat exhibited a remarkable loading capacity; for a boat with a volume of 8.0 cm³, the maximum loading was 11.6 or 12.2 g when the boat weight is included. Moreover, the superhydrophobic cotton fabric showed a reasonable durability to withstand at least 30 machine washing cycles.     

Fabrication of a superhydrophobic surface on a wood substrate

A layer of lamellar superhydrophobic coating was fabricated on a wood surface through a wet chemical process. The superhydrophobic property of the wood surface was measured by contact angle (CA) measurements. The microstructure and chemical composition of the superhydrophobic coating were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). An analytical characterization revealed that the microscale roughness of the lamellar particles was uniformly distributed on the wood surface and that a zinc stearate monolayer (with the hydrophobic groups oriented outward) formed on the ZnO surface as the result of the reaction between stearic acid and ZnO. This process transformed the wood surface from hydrophilic to superhydrophobic: the water contact angle of the surface was 151°, and the sliding angle was less than 5°.     

Thermal stable superhydrophobic polyphenylsilsesquioxane/nanosilica composite coatings

The superhydrophobic polyphenylsilsesquioxane (PPSQ)/nanosilica composite coatings were prepared by spray coating method with nano fumed silica (NFS) particles embedded in PPSQ matrix. The water contact angle (WCA) increased from 92.9° to 152.5° and the sliding angle (SA) decreased from more than 60° to 3.9° as the NFS content increased. The superhydrophobicity retained up to 500 °C, sustained by the hierarchical micro-nano structures and excellent thermal stability of PPSQ. A superhydrophobic PPSQ coating with WCA of 152.6° and SA of 7.8° was obtained by solvent-nonsolvent method for comparison as well. However, it gradually lost superhydrophobicity at 200 °C because of the elimination of nanostructures by the thermal softening of PPSQ.     

A novel method to fabricate superhydrophobic surfaces based on well-defined mulberry-like particles and self-assembly of polydimethylsiloxane

A superhydrophobic surface was obtained by combining application of CaCO₃/SiO₂ mulberry-like composite particles, which originated from violent stirring and surface modification, and self-assembly of polydimethylsiloxane. Water contact angle and sliding angle of the superhydrophobic surface were measured to be about 164 ± 2.5° and 5°, respectively. The excellent hydrophobicity is attributed to the synergistic effect of micro-submicro-nano-meter scale roughness (fabricated by composite particles) and the low surface energy (provided by polydimethylsiloxane). This procedure makes it possible for widespread applications of superhydrophobic film due to its simplicity and practicability.     

Conciliating surface superhydrophobicities and mechanical strength of porous silicon films

Hydrophobic surfaces on Mechanical stable macroporous silicon films were prepared by electrochemical etching with subsequent octadecyltrichlorosilane (OTS) modification. The surface morphologies were controlled by current densities and the mechanical properties were adjusted by their corresponding porosities. Contrast with the smooth macroporous silicon films with lower porosities (34.1%) and microporous silicon with higher porosities (97%), the macroporous film with a rough three-dimension (3D) surface and a moderate pore to cross-section area ratio (37.8%, PSi2′) exhibited both good mechanical strength (Yong’ modulus, shear modulus and collapse strength are 64.2, 24.1 and 0.32 GPa, respectively) and surface superhydrophobicity (water contact angle is 158.4 ± 2° and sliding angle is 2.7 ± 1°). This result revealed that the surface hydrophobicities (or the surface roughness) and mechanical strength of porous films could be conciliated by pore to cross-section area ratios control and 3D structures construction. Thus, the superhydrophobic surfaces on mechanical stable porous films could be obtained by 3D structures fabrication on porous film with proper pore to cross-section area ratios.     

A novel simple approach to preparation of superhydrophobic surfaces of aluminum alloys

A novel two-step methodology is successfully developed to fabricate superhydrophobic surfaces of aluminum alloys. The essential procedure is that samples are first immersed and etched in a boiling aqueous solution of NaOH for 5 min without preprocessing, and then they are modified for 30 min in an ethanol solution of lauric acid, cheaper and more efficient than the fluorinated silane frequently adopted by other researchers. If the concentration of NaOH solution is larger than 5 g/L, the contact angle of the prepared surfaces will be larger than 150° with a negligible hysteresis. Such a fast, low-cost, and reliable method for superhydrophobic surfaces implies significant promising industrial applications.