Correlation between the surface chemistry and the atmospheric corrosion of AZ31, AZ80 and AZ91D magnesium alloys

X-ray photoelectron spectroscopy (XPS) was used in order to investigate the correlation between the surface chemistry and the atmospheric corrosion of AZ31, AZ80 and AZ91D magnesium alloys exposed to 98% relative humidity at 50 °C. Commercially pure magnesium, used as the reference material, revealed MgO, Mg(OH)₂ and tracers of magnesium carbonate in the air-formed film. For the AZ80 and AZ91D alloys, the amount of magnesium carbonate formed on the surface reached similar values to those of MgO and Mg(OH)₂. A linear relation between the amount of magnesium carbonate formed on the surface and the subsequent corrosion behaviour in the humid environment was found. The AZ80 alloy revealed the highest amount of magnesium carbonate in the air-formed film and the highest atmospheric corrosion resistance, even higher than the AZ91D alloy, indicating that aluminium distribution in the alloy microstructure influenced the amount of magnesium carbonate formed.     

Study on the solidification microstructure in AZ91D Mg alloy after laser surface melting

Laser surface melting (LSM) is known to enhance the wear and corrosion resistance of Mg alloys, but its effect on microstructural evolution of Mg alloys is not well understood. An effort has been made to study the effect of rapid solidification following LSM on the microstructural evolution of AZ91D Mg alloy. The results of X-ray diffractometry, scanning electron microscopy, transmission electron microscopy and energy-dispersive X-ray spectroscopy indicated that the solidification microstructure in the laser-melted zone was mainly cellular/dendrite structure of primarily α-Mg phase and continuous network of β-Mg₁₇Al₁₂ phase. Numerical prediction of the laser-melted zone suggested that cooling rates increased strongly from the bottom to the top surface in the irradiated regions. An attempt has been made to correlate dendrite cell sizes of the solidification microstructure with the cooling rates in the laser-treated AZ91D Mg alloy.     

Broad-beam laser cladding of Al-Cu alloy coating on AZ91HP magnesium alloy

The resistance to wear and corrosion of AZ91HP Mg alloy was improved by laser cladding Al-Cu alloy. It was found that the clad layer was characterized by AlCu₄ and Mg₁₇Al₁₂ grains embedded in a AlMg matrix. The bonding zone exhibited a white-light planar crystal band with thickness of 10-13 μm. The heat-affected zone formed a eutectic structure due to the Mg diffusion. The microhardness and wear resistance of the coating were improved due to the formation of the hard phases AlCu₄ and Mg₁₇Al₁₂. Owing to the formation of dense Al₂O₃ oxide film, the coating exhibited better corrosion resistance in 3.5 wt.% NaCl solution.     

Studies on influence of zinc immersion and fluoride on nickel electroplating on magnesium alloy AZ91D

The effect of zinc immersion and the role of fluoride in nickel plating bath were mainly investigated in nickel electroplating on magnesium alloy AZ91D. The state of zinc immersion, the composition of zinc film and the role of fluoride in nickel plating bath were explored from the curves of open circuit potential (OCP) and potentiodynamic polarization, the images of scanning electron microscopy (SEM) and the patterns of energy dispersive X-ray (EDX). Results show that the optimum zinc film mixing small amount of Mg(OH)₂ and MgF₂ is obtained by zinc immersion for 30-90 s. The corrosion potential of magnesium alloy substrate attached zinc film will be increased in nickel plating bath and the quantity of MgF₂ sandwiched between magnesium alloy substrate and nickel coating will be reduced, which contributed to produce nickel coating with good performance. Fluoride in nickel plating bath serves as an activator of nickel anodic dissolution and corrosion inhibitor of magnesium alloy substrate. 1.0-1.5 mol dm⁻³ of F⁻ is the optimum concentration range for dissolving nickel anode and protecting magnesium alloy substrate from over-corrosion in nickel plating bath. The nickel coating with good adhesion and high corrosion resistance on magnesium alloy AZ91D is obtained by the developed process of nickel electroplating. This nickel layer can be used as the rendering coating for further plating on magnesium alloys.     

Characterization of ceramic PVD thin films on AZ31 magnesium alloys

Ceramic thin films have been widely used to protect the metal substrate as coatings in the past years. In order to improve the poor corrosion resistance of AZ31 magnesium alloy, the study in this paper used the electron beam evaporation method to prepare ceramic PVD films on its surface with TiO₂ and Al₂O₃ as donors, respectively. Atomic force microscopy (AFM), scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), Auger electron spectroscopy (AES) and X-ray diffraction (XRD) were used to investigate the surface morphology, composition and microstructure of the thin films. Both films deposited on AZ31 took on compact top surface morphologies and grew as amorphous structures on substrate. AES test not only showed that films compositions deviated the standard stoichiometric ratios, but also found that element Mg diffused into films and existed as magnesium oxide in the TiO_x film as well as the AlO_x film. In the electrochemical corrosion test, the AlO_x coating on AZ31 exhibited the largest electrochemical impedance in a 3.5% NaCl solution. But it did not show better corrosion resistance than others for the poorer adhesion. Even if its thickness was small, the TiO_x coating on AZ31 exhibited the best corrosion resistance in this study. According to the observation and analysis, the damage of these films on AZ31 in aggressive solutions was mainly due to the existence of pores, microcracks, vacancies and poor adhesion between coating and substrate.     

Electrodeposition of high corrosion resistance Cu/Ni-P coating on AZ91D magnesium alloy

High corrosion resistance Cu/Ni-P coatings were electrodeposited on AZ91D magnesium alloy via suitable pretreatments, such as one-step acid pickling-activation, once zinc immersion and environment-friendly electroplated copper as the protective under-layer, which made Ni-P deposit on AZ91D Mg alloy in acid plating baths successfully. The pH value and current density for Ni-P electrodeposition were optimized to obtain high corrosion resistance. With increasing the phosphorous content of the Ni-P coatings, the deposits were found to gradually transform to amorphous structure and the corrosion resistance increased synchronously. The anticorrosion ability of AZ91D Mg alloy was greatly improved by the amorphous Ni-P deposits, which was investigated by potentiodynamic polarization curve and electrochemical impedance spectroscopy (EIS). The corrosion current density (I_corr) of the coated Mg alloy substrate is about two orders of magnitude less than that of the uncoated.     

Preparation and properties of composite ceramic coating containing Al2O3–ZrO2–Y2O3 on AZ91D magnesium alloy by plasma electrolytic oxidation

A composite ceramic coating containing Al₂O₃–ZrO₂–Y₂O₃ was successfully prepared on AZ91D magnesium alloy by plasma electrolytic oxidation (PEO) technique in an alkaline aluminate electrolyte. The morphology, elemental and phase composition, corrosion behavior and thermal stability of the uncoated and coated samples were studied by environmental scanning electron microscopy (ESEM), energy dispersive X-ray spectrometer (EDS), X-ray diffractometer (XRD), electrochemical corrosion test, high temperature oxidation test and thermal shock test. The results showed that the composite ceramic coating was composed of Al₂O₃, c-ZrO₂, t-ZrO₂, Y₂O₃ and some magnesium compounds, such as MgO, MgF₂ and MgAl₂O₄. After PEO treatment, the corrosion potential of AZ91D alloy was increased and the corrosion current density was significantly reduced. Besides, the coated magnesium alloys also showed excellent high temperature oxidation resistance and thermal shock resistance at 500 °C environment.     

Solidification microstructure of AZ91D Mg alloy after laser surface melting

The solidification microstructure plays a critical role in determining the surface properties of laser-treated magnesium alloys. The purpose of this paper is to study the solidification microstructures of AZ91D Mg alloy following millisecond- and nanosecond-pulse Nd:YAG laser irradiation. The solidification microstructural evolution of laser-melt AZ91D Mg alloy was investigated using X-ray diffractometry, scanning electron microscopy, energy-dispersive X-ray spectrometer and transmission electron microscopy. Much refined α-Mg phase and β-Mg₁₇Al₁₂ intermetallics were observed in the microstructure after laser surface melting. Periodic and successive structure was observed in the millisecond irradiated surface and the melt depth was more than 100 μm. The solidification microstructure was mainly cellular/dendrite structures together with a large number of β-Mg₁₇Al₁₂ nano-particles. Micron holes were found in the nanosecond irradiated surface and the melt depth was shallow at 50 μm. Millisecond-pulse Nd:YAG laser was found to be more suitable for Mg alloy surface treatment due to sufficient melt depth.     

Effect of the chemistry and structure of the native oxide surface film on the corrosion properties of commercial AZ31 and AZ61 alloys

The purpose of this study has been to advance in knowledge of the chemical composition, structure and thickness of the thin native oxide film formed spontaneously in contact with the laboratory atmosphere on the surface of freshly polished commercial AZ31 and AZ61 alloys with a view to furthering the understanding of protection mechanisms. For comparative purposes, and to more fully describe the behaviour of the native oxide film, the external oxide films formed as a result of the manufacturing process (as-received condition) have been characterised. The technique applied in this research to study the thin oxide films (thickness of just a few nanometres) present on the surface of the alloys has basically been XPS (X-ray photoelectron spectroscopy) in combination with ion sputtering. Corrosion properties of the alloys were studied in 0.6 M NaCl by measuring charge transfer resistance values, which are deduced from EIS (electrochemical impedance spectroscopy) measurements after 1 h of exposure. Alloy AZ61 generally showed better corrosion resistance than AZ31, and the freshly polished alloys showed better corrosion resistance than the alloys in as-received condition. This is attributed to a combination of (1) higher thickness of the native oxide film on the AZ61 alloy and (2) greater uniformity of the oxide film in the polished condition. The formation of an additional oxide layer composed by a mixture of spinel (MgAl₂O₄) and MgO seems to diminish the protective properties of the passive layer on the surface of the alloys in as-received condition.     

Plasma electrolytic oxidation coating on AZ91 magnesium alloy modified by neodymium and its corrosion resistance

Ceramic coatings on the surfaces of Mg-9Al-1Zn (AZ91) magnesium alloy and Mg-9Al-1Zn-1Nd magnesium alloy (AZ91 magnesium alloy modified by neodymium, named as AZ91Nd in this paper) are synthesized in aluminate electrolyte by plasma electrolytic oxidation (PEO) process, respectively. X-ray diffraction and X-ray photoelectron spectroscopy analyses show the PEO coating on the Mg-9Al-1Zn-1Nd alloy comprises not only MgO and Al₂O₃, which are found in the coating on the AZ91 alloy, but also a trace amount of Nd₂O₃. Microstructure observations indicate the addition of Nd can decrease the sizes of β phases and form Al₂Nd intermetallics in the AZ91 alloy. The fine β phases can effectively restrain the formation of unclosed-holes and greatly decrease the sizes of pores in the coating during the PEO process. In addition, the Al₂Nd intermetallics can be completely covered due to the lateral growth of the PEO coatings formed on the α and β phases. As a result, the coating on the AZ91Nd alloy possesses a dense microstructure compared with that on the AZ91 alloy. The following corrosion tests indicate the corrosion resistance of the PEO coating on the AZ91Nd alloy is evidently higher than that of the PEO coating on the AZ91 alloy.     

Bi，Sb合金化对AZ91镁合金组织、性能影响机理研究

利用大角重位点阵模型建立了AZ91镁合金α相［0001］对称倾斜晶界原子结构模型，应用实空间的连分数方法计算了Mg合金的总结构能，合金元素引起的环境敏感镶嵌能及原子间相互作用能，讨论了主要合金元素Al及Bi，Sb在AZ91中的合金化行为.计算结果表明，Al，Bi，Sb固溶于α相内或晶界区使总结构能都降低，起到固溶强化作用；合金元素在AZ91α相内趋于均匀分布，在晶界区易占位于三角椎上部.AZ91镁合金中加入Bi或Sb时，Bi或Sb比Al容易偏聚于晶界，从而抑制了Al在晶界的偏聚，促进基体中连续的Mg₁₇Al₁₂相的析出，提高AZ91合金室温性能； AZ91合金中(α相内和晶界区)主要合金元素Al和微加元素Bi，Sb都能够形成有序相Mg₁₇Al₁₂，Mg₃Bi₂或Mg₃Sb₂，且在晶界区形成的量大.Bi，Sb加入AZ91合金中，由于Bi，Sb抑制Al在晶界的偏聚，晶界区主要析出相为Mg₃Bi₂或Mg₃Sb₂，提高镁合金高温性能. 关键词： 电子理论 合金化 晶界偏聚 镁合组织与性能     

Growth and characterization of Mg(OH)2 film on magnesium alloy AZ31

Magnesium-based biomaterials have been proposed as potential candidates for biodegradable implant materials, such as bone screws, bone plates, intraluminal stents and so on. However, the poor corrosion resistance inhibits their applications in surgery. They collapse before the injured tissues are healed. In this paper, Mg(OH)₂ nonstructural film was synthesized on the substrate of AZ31 magnesium alloy by hydrothermal method with NaOH solution as mineralizer to reduce the corrosion rate of magnesium-based materials. The obtained films were characterized by XRD, SEM, and XPS. The results showed that a Mg(OH)₂ film with nanostructure surface can be synthesized by hydrothermal method. It was observed that the thickness of film increased with the holding time. Corrosion rates of the films were studied by immersing the samples in Hank's solution (37 °C). Surface deposits of samples with films soaked in Hank's solution for 31 days were investigated by XRD, SEM, EDS, XPS, and FTIR. It verified that the corrosion rate of the magnesium alloy with grown film was slowed down in the Hank's solution and the behavior of corrosion was inhibited effectively. Amorphous calcium apatite precursor was observed to deposit on the surface of the film during corrosion experiments in Hank's solution. And the tape test revealed a strong adhesion between the film and the substrate.     

The resistance to wear and corrosion of laser-cladding Al2O3 ceramic coating on Mg alloy

The paper presents a study on the preparation of Al₂O₃ ceramic coating on AZ91HP Mg alloy by laser remelting plasma-sprayed coating. It was found that after laser remelting, the coating exhibited obvious layer-like characteristics due to influence of temperature distribution, thermophysical parameters and layer thickness. According to the microstructural difference, the coating can be divided into the melted zone with the α-Al₂O₃ column-like crystal, the sintered zone with flock-like structure, the residual plasma-sprayed zone with loosened structure. Because of the dense column-like crystal, the hardness, wear and corrosion resistance of the laser remelted coating are much higher than those of the plasma-sprayed coating and as-received Mg alloy.     

Electrodeposition of Al-Mn alloy on AZ31B magnesium alloy in molten salts

The Al-Mn alloy coatings were electrodeposited on AZ31B Mg alloy in AlCl₃-NaCl-KCl-MnCl₂ molten salts at 170 °C aiming to improve the corrosion resistance. However, in order to prevent AZ31B Mg alloy from corrosion during electrodeposition in molten salts and to ensure excellent adhesion of coatings to the substrate, AZ31B Mg alloy should be pre-plated with a thin zinc layer as intermediate layer. Then the microstructure, composition and phase constituents of the coatings were investigated by scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDX), and X-ray diffraction (XRD). It was indicated that, by adjusting the MnCl₂ content in the molten salts from 0.5 wt% to 2 wt%, the Mn content in the alloy coating was increased and the phase constituents were changed from f.c.c Al-Mn solid solution to amorphous phase. The corrosion resistance of the coatings was evaluated by potentiodynamic polarization measurements in 3.5% NaCl solution. It was confirmed that the Al-Mn alloy coatings exhibited good corrosion resistance with a chear passive region and significantly reduced corrosion current density at anodic potentiodynamic polarization. The corrosion resistance of the alloy coatings was also related with the microstructure and Mn content of the coatings.     

Chemical nature of phytic acid conversion coating on AZ61 magnesium alloy

Phytic acid (PA) conversion coating on AZ61 magnesium alloy was prepared by the method of deposition. The influences of pH, time and PA concentration on the formation process, microstructure and properties of the conversion coating were investigated. Scanning electron microscopy (SEM) was used to observe the microstructure. The chemical nature of conversion coating was investigated by energy dispersive X-ray spectroscopy (EDS) and Fourier transform infrared spectroscopy (FTIR) techniques. The corrosion resistance was examined by means of potentiodynamic polarization method. The adhesive ability was tested by score experiments. The results showed that the growth and microstructure of the conversion coatings were all obviously affected by pH, time and PA concentration. In 0.5 mg/ml PA solution with a pH of 5, an optimization conversion coating formed after 20 min immersion time by deposition of PA on AZ61 magnesium alloy surface through chelating with Al³⁺. It made the corrosion potential E_corr of sample shifted positively about 171 mV than that of the untreated sample, and the adhesive ability reached to Grade 1 (in accordance with GB/T 9286).     

Corrosion behaviors in physiological solution of cerium conversion coatings on AZ31 magnesium alloy

In this paper, a non-toxic Ce-based conversion coating was obtained on the surface of bio-medical AZ31 magnesium alloys. The micro-morphology of the coating prepared with optimal technical parameters and immersed in physiological solution (Hank's solution) in different time was observed by scanning electron microscopy (SEM), composition of the cerium conversion coating and corrosion products in Hank's solution were characterized by X-ray photoelectron spectroscopy (XPS) and energy dispersive spectroscopy (EDS), respectively. In addition, the corrosion property in Hank's solution was studied by electrochemical experiment and immersion test. The results show that the dense Ce-based conversion coating is obtained on the surface of AZ31 magnesium alloys in optimal technical parameters and the conversion coating consists of a mass of trivalent and tetravalent cerium oxides. The cerium conversion coating can provide obvious protection of magnesium alloys and can effectively reduce the degradation speed in Hank's solution. Also the degradation products have little influence on human body.     

Mg NMR site analysis in metals and intermetallics

Nuclear magnetic resonance (NMR) of the low abundance and low gyromagnetic ratio isotope ²⁵Mg, I=5/2, 2.606 MHz/T, 10% abundant, is shown here to provide an informative probe for phase identification, site symmetry and site multiplicity of the intermetallic compounds which occur as strengthening precipitate phases in lightweight alloys. The intermetallics discussed here, Mg₁₇Al₁₂, MgZn₂, Mg₂Al₃ and Al₂CuMg, are the final equilibrium precipitate phases in a number of Mg- and Al-based heat-treatable alloys. The ²⁵Mg spectra of Mg in Al–10 at%Mg alloy show the progressive precipitation of Mg₂Al₃ from Mg in solid solution as a function of annealing time at 150 °C. Also reported are ²⁵Mg spectra for CuMg₂, Mg₄₄Al₁₅Zn₄₁ and Mg₂Sn, along with the counter atom ⁶⁷Zn and ⁶³Cu NMR spectra for MgZn₂ and CuMg₂. All spectra are simulated to determine nuclear interaction parameters and confirm site occupancy.     

Enhancement of photoluminescence intensity from Si nanodots using Al2O3 surface passivation layer grown by atomic layer deposition

Temperature-dependent photoluminescence (PL) from Si nanodots with Al₂O₃ surface passivation layers was studied. The Si nanodots were grown by low pressure chemical vapor deposition and the Al₂O₃ thin films were prepared by atomic layer deposition (ALD), respectively. The BOE (Buffer-Oxide-Etch) treatment resulted in the damaged surface of Si nanodots and thus caused dramatic reduction in the PL intensity. Significant enhancement of the PL intensity from Si nanodots after the deposition of Al₂O₃ thin films was observed over a wide temperature range, indicating the remarkable surface passivation effect to suppress the non-radiative recombination at the surface of Si nanodots. The results demonstrated that the Al₂O₃ surface passivation layers grown by ALD are effectually applicable to nanostructured silicon devices.     

Effect of Al on the electrochemical corrosion behaviour of Pb free Sn-8.5 Zn-0.5 Ag-XAl-0.5 Ga solder in 3.5% NaCl solution

The effect of Al on the electrochemical corrosion behaviour of Pb-free Sn-8.5 Zn-0.5 Ag-XAl-0.5 Ga solder in 3.5% NaCl solution was investigated by using potentiodynamic polarization techniques. The X content in the solder varied from 0.1 to 3 wt.%. Polarization studies revealed that an increase in Al content upto 1.5 wt.% decreased the corrosion current density (I_corr), corrosion rate of the solder and shifted the corrosion potential (E_corr) towards more noble values. However, higher content of Al, i.e. 3 (wt.%) in the five-element solder enhanced the corrosion rate and resulted in a significant increase in the E_corr towards more negative values. Passivation behaviour was noticed in all the solders having varying Al content, but the passive film formed at 1.5 wt.% Al was most stable due to its low passivation current density (i_p) and low critical current density (i_cc) value in comparison to the other solders. XPS and Auger depth profile results revealed that the passive film consisted of oxides/hydroxides of Al and Zn formed on the surface of the solder with Sn being formed in the subsequent layer. Considerable aluminium segregation occurred towards the surface principally as Al₂O₃/Al(OH)₃ with increase in Al content to 1.5 wt.% in the five element solder. The formation of Al₂O₃ seemed to prevent the oxidation of zinc on the surface of the solder.     

Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy

Composite coatings using pure Al powder blended with α-Al₂O₃ as feedstock were deposited on AZ91D magnesium alloy substrates by cold spray (CS). The content of α-Al₂O₃ in the feedstock was 25 wt.% and 50 wt.%, respectively. The effects of α-Al₂O₃ on the porosity, microhardness, adhesion and tensile strength of the coatings were studied. Electrochemical tests were carried out in neutral 3.5 wt.% NaCl solution to evaluate the effect of α-Al₂O₃ on the corrosion behavior of the coatings. The results showed that the composite coatings possessed lower porosity, higher adhesion strength and tensile strength than cold sprayed pure Al coating. The corrosion current densities of the composite coatings were similar to that of the pure Al coating and much higher than that of bare AZ91D magnesium alloy.