The influence of casting parameters on the surface morphology of PS‐b‐P4VP honeycomb films

The “breath figures” method provides an efficient and cost‐effective method to produce highly ordered honeycomb patterns in polymeric films at micrometer and sub‐micrometer dimensions. The size and regularity of the pores can be adjusted through a series of physical and chemical parameters. In this study, amphiphilic diblock copolymers, polystyrene‐block‐poly(4‐vinyl pyridine) (PS‐b‐P4VP) with different lengths of P4VP, were synthesized through Reversible Addition‐Fragmentation Chain Transfer polymerization. The honeycomb‐patterned films were prepared from these well‐defined polymers through the dynamic breath figures method. A series of physical parameters including solution concentration, flow rate, humidity of the flow, and the humidity of the casting environment, were delicately adjusted to systematically investigate their effects on the morphology of the films. These studies identified four key factors which were found to influence the formation of the pattern. No obvious effect was found on the pore size by changing the length of P4VP block. The result provides clear direction on the fabrication of PS‐b‐P4VP honeycomb‐patterned films and more broadly contributes a deeper understanding of the processes involved in the formation of honeycomb patterns. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3721–3732     

Control of pore size and pore uniformity in films based on self‐assembling block copolymers

Blends of self‐assembling polystyrene‐block‐poly(4‐vinyl pyridine) (PS‐b‐P4VP) diblock‐copolymers and poly(4‐vinyl pyridine) (P4VP) homopolymers were used to fabricate isoporous and nanoporous films. Block copolymers (BCP) self‐assembled into a structure where the minority component forms very uniform cylinders, while homopolymers, resided in the core of the cylinders. Selective removal of the homopolymers by ethanol immersion led to the formation of well‐ordered pores. In films without added homopolymer, just immersion in ethanol and subsequent swelling of the P4VP blocks was found to be sufficient to create pores. Pore sizes were tuned between 10 and 50 nm by simply varying the homopolymer content and the molecular weight of the block‐copolymer. Uniformity was lost when the average pore size exceeded 30 nm because of macrophase separation. However, preparation of films from low M_W diblock copolymers showed that it is possible to have excellent pore size control and a high porosity, while retaining a low pore size distribution. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1568–1579     

Synthesis and self‐assembly of diblock copolymers bearing 2‐nitrobenzyl photocleavable side groups

The light‐responsive behavior in solution and in thin films of block copolymers bearing 2‐nitrobenzyl photocleavable esters as side groups is discussed in this article. The polymers were synthesized by grafting 2‐nitrobenzyl moieties onto poly(acrylic acid)‐block‐polystyrene (PAA‐b‐PS) precursor polymers, leading to poly(2‐nitrobenzyl acrylate‐random‐acrylic acid)‐block‐polystyrene (P(NBA‐r‐AA)‐b‐PS) block copolymers. The UV irradiation of the block copolymers in a selective solvent for PS led to the formation of micelles that were used to trap hydrophilic molecules inside their core (light‐induced encapsulation). In addition, thin films consisting of light‐responsive P(NBA‐r‐AA) cylinders surrounded by a PS matrix were achieved by the self‐assembly of P(NBA‐r‐AA)‐b‐PS copolymers onto silicon substrates. Exposing these films to UV irradiation generates nanostructured materials containing carboxylic acids inside the cylindrical nanodomains. The availability of these chemical functions was demonstrated by reacting them with a functional fluorescent dye. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of poly(ethylene‐co‐vinyl alcohol)‐g‐polystyrene graft copolymer and their applications for ordered porous film and compatibilizer

A series of new functional poly(ethylene‐co‐vinyl alcohol)‐g‐polystyrene graft copolymers (EVAL‐g‐PS) with controlled molecular weight (M_n = 38,000–94,000 g mol^?1) and molecular weight distribution (M_w/M_n = 2.31–3.49) were synthesized via a grafting from methodology. The molecular structure and component of EVAL‐g‐PS graft copolymers were confirmed by the analysis of their ¹H NMR spectra and GPC curves. The porous films of such copolymers were fabricated via a static breath‐figure (BF) process. The influencing factors on the morphology of such porous films, such as solvent, temperature, polymer concentration, and molecular weight of polymer were investigated. Ordered porous film and better regularity was fabricated through a static BF process using EVAL‐g‐PS solution in CHCl₃. Scanning electron microscopy observation reveals that the EVAL‐g‐PS graft copolymer is an efficient compatibilizer for the blend system of low‐density polyethylene/polystyrene. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 516–524     

Synthesis and properties of ultralow dielectric porous polyimide films containing adamantane

A series of novel ultralow dielectric porous polyimide (PI) films containing adamantane groups was prepared via the thermolysis of polyethylene glycol (PEG) oligomers mixed into PI matrix. Scanning electron microscopy results indicated that the porous PI films showed closed pores with an average diameter of 120 ± 10 nm. Good thermal properties with 5% weight loss temperature of 499 °C in air atmosphere and glass transition temperature in excess of 310 °C were shown for porous PI films. Notably, the ultralow dielectric constant of porous PI films with 1.85 at 1 MHz was obtained and revealed via broadband dielectric spectroscopy. The effects of the chemical structure of the PI matrix and PEG content on the decomposition behavior of PEG and the performance of porous films were investigated. Wide‐angle X‐ray diffraction results indicated that the PI matrix with large d‐spacing generated weaker interactions between the PEG and PI backbone than those of PI matrix with small d‐spacing. As a result, the PEG for the PI matrix with large d‐spacing was completely decomposed. As indicated by the broadband dielectric spectroscopy results, lower dielectric porous PI films were prepared when the PEG contents in the PI matrix increased from 0 to 20 wt %. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 549–559     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

Polymethylene‐b‐polystyrene diblock copolymer: Synthesis,property, and application

The design and synthesis of well‐defined polymethylene‐b‐polystyrene (PM‐b‐PS, M_n = 1.3 × 10⁴–3.0 × 10⁴ g/mol; M_w/M_n (GPC) = 1.08–1.18) diblock copolymers by the combination of living polymerization of ylides and atom transfer radical polymerization (ATRP) was successfully achieved. The ¹H NMR spectrum and GPC traces of PM‐b‐PS indicated the successful extension of PS segment on the PM macroinitiator. The micellization behavior of such diblock copolymers in tetrahydrofuran were characterized by dynamic light scattering (DLS) and atomic force microscopy (AFM) techniques. The average aggregate sizes of PM‐b‐PS diblock copolymers with the same length of PM segment in tetrahydrofuran solution (1.0 mg mL^?1) increases from 104.2 nm to 167.7 nm when the molecular weight of PS segment increases. The spherical precipitated aggregates of PM‐b‐PS diblock copolymers with an average diameter of 600 nm were observed by AFM. Honeycomb porous films with the average diameter of 3.0 μm and 6.0 μm, respectively, were successfully fabricated using the solution of PM‐b‐PS diblock copolymers in carbon disulfide via the breath‐figure (BF) method under a static humid condition. The cross‐sections of low density polyethylene (LDPE)/polystyrene (PS)/PM‐b‐PS and LDPE/polycarbonate (PC)/PM‐b‐PS blends were observed by scanning electron microscope and reveal that the PM‐b‐PS diblock copolymers are effective compatilizers for LDPE/PS and LDPE/PC blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1894–1900, 2010     

Polystyrene‐b‐poly(2,2,2‐trifluoroethyl acrylate)‐b‐polystyrene copolymers: Synthesis and fabrication of their hydrophobic porous films,spheres, and fibers

New block copolymers Polystyrene‐b‐poly (2,2,2‐trifluoroethyl acrylate)‐b‐Polystyrene (PS‐PTFEA‐PS) with controlled molecular weight (M_n=5000‐11000 g?mol^?1) and narrow molecular weight distribution (M_w/M_n=1.13‐1.17) were synthesized via RAFT polymerization. The molecular structure and component of PS‐PTFEA‐PS block copolymers were characterized through ¹H NMR, ¹⁹F NMR, GPC, FT‐IR and elemental analysis. The porous films of such copolymers with average pore size of 0.80‐1.34 μm and good regularity were fabricated via a static breath‐figure (BF) process. The effects of solvent, temperature, and polymer concentration on the surface morphology of such film were investigated. In addition, microstructured spheres and fibers of such block copolymers were fabricated by electrospinning process and observed by scanning electron microscopy (SEM). Furthermore, the hydrophobicity of porous films, spheres, and fibers was investigated. The porous film showed a good hydrophobicity with the water‐droplet contact angles of 129°, and the fibers showed higher hydrophobicity with the water‐droplet contact angles of 142°. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 678–685     

Poly(methyl silsesquioxane)/amphiphilic block copolymer hybrids and their porous derivatives: Poly(styrene‐block‐acrylic acid) and poly(styrene‐block‐3‐trimethoxysilylpropyl methacrylate)

Porous poly(methyl silsesquioxane) (PMSSQ) films were prepared from PMSSQ/amphiphilic block copolymer (ABC) hybrids, and this was followed by spin coating and multistep baking. The ABCs were poly(styrene‐block‐acrylic acid) (PS‐b‐PAA) and poly(styrene‐block‐3‐trimethoxysilylpropyl methacrylate) (PS‐b‐PMSMA), which were synthesized by living polymerization. The chemical bonding between the ABCs and PMSSQ resulted in significant differences in the morphologies and properties of the hybrids and their porous derivatives. Both intramolecular and intermolecular hydrogen bonding existed in the PMSSQ/PS‐b‐PAA hybrid and led to macrophase separation. Through the modification of the chemical structure from the poly(acrylic acid) segment to PMSMA, covalent bonding between PMSSQ and PMSMA occurred and prevented the macrophase separation and initial pyrolysis of the ABC. Modulated differential scanning calorimetry results also suggested a significant difference in the miscibility of the two hybrid systems. The chemical bonding resulted in higher retardation of the symmetry‐to‐nonsymmetry Si? O? Si structural transformation for PMSSQ/PS‐b‐PMSMA than for PMSSQ/PS‐b‐PAA according to Fourier transform infrared studies. The pore size of the nanoporous thin film from the PMSSQ/PS‐b‐PMSMA hybrid was estimated by transmission electron microscopy to be less than 15 nm. The refractive index and dielectric constant of the prepared porous films decreased from 1.354 to 1.226 and from 2.603 to 1.843 as the PS‐b‐PMSMA loading increased from 0 to 50 wt %, respectively. This study suggests that chemical bonding in hybrid materials plays a significant role in the preparation of low‐dielectric‐constant nanoporous films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4466–4477, 2004     

Direct spincasting of polystyrene thin films onto poly(methyl methacrylate)

The low vapor pressure solvent 1‐chloropentane was used to directly spincast polystyrene (PS) films onto poly(methyl methacrylate) (PMMA) with smooth surfaces and sharp interfaces. Interface roughness after removal of the PS layer with cyclohexane was determined with scanning force microscopy to be <1 nm. Dynamic secondary mass spectroscopy revealed an interfacial width below the resolution limit of ～10 nm. Large area bilayers with smooth surfaces could be created. In addition, direct spincasting with 1‐chloropentane allows the production of thin PS films (<15 nm) and films of low molecular weight (<5 kDa) PS, all of which would be impossible to produce for this important model system by the traditional water‐transfer method. 1‐chloropentane was confirmed to be a sufficiently selective solvent for PS by measuring the Flory–Huggins χ parameters of 1‐chloropentane with PS and PMMA, respectively, with inverse gas chromatography. In the search for a suitable selective solvent, the authors have also examined the role of vapor pressure in spin casting smooth films over a wider molecular weight (4.3–190 kDa) and thickness range (～5–500 nm) than previously reported. Only solvents with low vapor pressure produced high quality PS films. Methylcyclohexene can also be used to produce excellent, directly cast PS/PMMA bilayers, but with a smaller molecular weight and thickness window compared with 1‐chloropentane. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3234–3244, 2006     

Influences of organometallic polymer‐derived catalyst dispersion on SWNT growth

Catalyst formation kinetics of a ferrocene‐containing homopolymer, polyferrocenylethylmethylsilane (PFEMS), is investigated as it relates to the catalysis of single walled carbon nanotubes (SWNTs) through a chemical vapor deposition (CVD) process. The formation and efficiency of the PFEMS‐based iron catalyst is compared with that of the corresponding polystyrene (PS)‐b‐PFEMS diblock copolymer. The PFEMS homopolymer contains 23 wt % iron, while PS‐b‐PFEMS, with a 25 vol % PFEMS content, is only 6% iron. Despite its lower iron content, spin‐cast PS‐b‐PFEMS films on SiO₂/Si substrates produce more active iron sites than spin‐cast PFEMS films during CVD growth of SWNTs. This is related to the self‐assembly of the block copolymer, where PFEMS domains are well dispersed in the PS matrix, which degrades at a CVD temperature of 920 °C to leave catalytically active elemental iron behind. On the contrary, the pure PFEMS films contain a high percentage of iron and silicon, which tend to transform into ceramic‐coated iron at this high temperature, thus rendering the iron inactive towards SWNT growth. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 758–765, 2007     

Synthesis of ω‐sulfonated polystyrene via reversible addition fragmentation chain transfer polymerization and postpolymerization modification

The synthesis of chain‐end sulfonated polystyrene [PS (ω‐sulfonated PS)] by reversible addition fragmentation chain transfer (RAFT) polymerization followed by postpolymerization modification was investigated by two methods. In the first method, the polymer was converted to a thiol‐terminated polymer by aminolysis. This polymer was then sulfonated by oxidation of the thiol end‐group with m‐chloroperoxybenzoic acid (m‐CPBA) to produce a sulfonic acid end‐group. In the second method, the RAFT‐polymerized polymer was directly sulfonated by oxidation with m‐CPBA. After purification by column chromatography, ω‐sulfonated PS was obtained by both methods with greater than 95% end‐group functionality as measured by titration. The sulfonic acid end‐group could be neutralized with various ammonium or imidazolium counter ions through acid–base or ionic metathesis reactions. The effect of the ionic end‐groups on the glass transition temperature of the PS was found to be consistent with what is known for PS ionomers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Dispersion RAFT polymerization of 4‐vinylpyridine in toluene mediated with the macro‐RAFT agent of polystyrene dithiobenzoate: Effect of the macro‐RAFT agent chain length and growth of the block copolymer nano‐objects

The dispersion reversible addition‐fragmentation chain transfer (RAFT) polymerization of 4‐vinylpyridine in toluene in the presence of the polystyrene dithiobenzoate (PS‐CTA) macro‐RAFT agent with different chain length is discussed. The RAFT polymerization undergoes an initial slow homogeneous polymerization and a subsequent fast heterogeneous one. The RAFT polymerization rate is dependent on the PS‐CTA chain length, and short PS‐CTA generally leads to fast RAFT polymerization. The dispersion RAFT polymerization induces the self‐assembly of the in situ synthesized polystyrene‐b‐poly(4‐vinylpyridine) block copolymer into highly concentrated block copolymer nano‐objects. The PS‐CTA chain length exerts great influence on the particle nucleation and the size and morphology of the block copolymer nano‐objects. It is found, short PS‐CTA leads to fast particle nucleation and tends to produce large‐sized vesicles or large‐compound micelles, and long PS‐CTA leads to formation of small‐sized nanospheres. Comparison between the polymerization‐induced self‐assembly and self‐assembly of block copolymer in the block‐selective solvent is made, and the great difference between the two methods is demonstrated. The present study is anticipated to be useful to reveal the chain extension and the particle growth of block copolymer during the RAFT polymerization under dispersion condition. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Selective swelling induced pore generation of amphiphilic block copolymers: The role of swelling agents

Swelling of block copolymers by selective solvents has emerged as an extremely simple and efficient process to produce nanoporous materials with well‐controlled porosities. However, the role of the swelling agents in this pore‐making process remains to be elucidated. Here we investigate the evolution of morphology, thickness, and surface chemistry of thin films of polystyrene‐block‐poly (2‐vinyl pyridine) (PS‐b‐P2VP) soaked in a series of alcohols with changing carbon atoms and hydroxyl groups in their molecules. It is found that, in addition to a strong affinity to the dispersed P2VP microdomains, the swelling agents should also have a moderate swelling effect to PS to allow appropriate plastic deformation of the PS matrix. Monohydric alcohols with longer aliphatic chains exhibit stronger ability to induce the pore formation and a remarkable increase in film thickness is associated with the pore formation. High‐carbon alcohols including n‐propanol, n‐butanol, and n‐hexanol produce cylindrical micelles upon prolonged exposure for their strong affinity toward the PS matrix. In contrast, methanol and polyhydric alcohols including glycol and glycerol show very limited effect to swell the copolymer films as their affinity to the PS matrix is low; however, they also evidently induce the surface segregation of P2VP blocks. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 926–933     

Surface modification of polystyrene by blending substituted styrene copolymers

The surface modification of polystyrene (PS) by the blending of 4‐acetoxystyrene polymers and their corresponding hydrolysis products, 4‐hydroxystyrene polymers, was investigated on the basis of X‐ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and contact‐angle measurements. According to XPS and AFM measurements, when polystyrene‐block‐poly(4‐acetoxystyrene) (PS‐b‐PAS) or polystyrene‐block‐poly(4‐hydroxystyrene) (PS‐b‐PHS) was incorporated into PS, the block copolymer was preferentially segregated at the highest surface region of the blend. This segregation increased to a plateau value when more than 5 wt % of either PS‐b‐PHS or PS‐b‐PAS was added. The contact angle of the modified PS by PS‐b‐PAS or PS‐b‐PHS was slightly lower than that of homopolystyrene, but no further decrease was observed with the blend ratio of the diblock copolymer increasing from 5 to 20 wt %. For a PS/PS‐b‐PHS blend, the surface atomic concentration ratio O/C increased linearly with the molecular weight of poly(4‐hydroxystyrene) blocks in diblock copolymer PS‐b‐PHS in the range of our study. The different structures of 4‐acetoxystyrene polymers and their hydrazinolyzed materials may affect the surface compositions of their blends with PS; among these polymers, PS‐b‐PHS and PS‐b‐PAS appeared to be most effective. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1046–1054, 2001     

Synthesis and morphology of polyethylene chains grafted onto the surface of crosslinked polystyrene microspheres

The bifunctional comonomer 4‐(3‐butenyl) styrene was used to synthesize crosslinked polystyrene microspheres (c‐PS) with pendant butenyl groups on their surface via suspension copolymerization. Polyethylene chains were grafted onto the surface of c‐PS microspheres (PS‐g‐PE) via ethylene copolymerizing with the pendant butenyl group on the surface of the c‐PS microspheres under the catalysis of metallocene catalyst. The composition and morphology of the PS‐g‐PE microspheres were characterized by means of Fourier transform infrared spectroscopy, Fourier transform Raman spectroscopy, X‐ray photoelectron spectroscopy, and field‐emission scanning electron microscopy. It is possible to control the content of PE grafted onto the surface of c‐PS microspheres by varying the polymerization time or the initial quantity of pendant butenyl group on the surface of c‐PS microspheres. Investigation on the morphology and crystallization behavior of grafted PE chains showed that different surface patterns could be formed under various crystallization conditions. Moreover, the crystallization temperature of PE chains grafted on the surface of c‐PS microspheres was 6 °C higher than that of pure PE. The c‐PS microspheres decorated by PE chains had a better compatibility with PE matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4477–4486, 2007     

Attapulgite grafted with polystyrene via a simultaneous reverse and normal initiation atom transfer radical polymerization

The surface grafting of attapulgite (ATP) with polystyrene (PS) was established via a simultaneous reverse and normal initiation atom transfer radical polymerization (SR&NIATRP). 4‐(chloromethyl)phenyltrimethoxysilane (CMPTMS) chemical bounded on the surface of ATP (ATP‐Cl, Cl‐I) was prepared via one‐step self‐assembly. SR&NI ATRP of styrene was conducted using CuCl₂ complex tris(2‐(dimethylamino)ethyl)amine (Me₆‐TREN) as the catalytic system, initiated by 2,2‐azobis(isobutyronitrile) (AIBN) and ATP‐Cl. FT‐IR, XRD, XPS, TGA and TEM data were consistent with the grafting of benzyl chloride groups and PS chains on ATP surface. The controllability of polymerization was investigated by the kinetics behavior under different molar ratio of AIBN and CuCl₂. The obtained polymer possessed a uniform distribution of molecular weights with a lower polydispersity index of 1.2～1.4. The relationship between polymerization on the surface of ATP and in solution was discussed in detail based on TGA data of hybrid particles and GPC trace of free polymer in solution. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1508–1516     

π-complexes of polystyrene with silver salts and their use as facilitated olefin transport membranes

π-Complexes of silver salts with polystyrene (PS) were prepared and tested in the separation of propylene/propane mixtures. After the incorporation of silver ions into the PS matrix, both the pure propylene gas permeance of the membrane and its olefin selectivity with respect to the propylene/propane mixtures were remarkably higher than those of the pure PS membrane, demonstrating facilitated propylene transport through the solid-state membrane. The remarkable separation performance of the PS/silver salt membranes was attributable to the unusually high solubility of the silver salts in the PS matrix, which was possibly due to the formation of π-complexes between the silver ion and aromatic CC bond of PS. The coordination properties and dissolution behavior of the silver salts in PS were investigated with Fourier transform infrared, Fourier transform Raman, and X-ray photoelectron spectroscopy. The values for the intersegmental d-spacing, determined by wide-angle X-ray scattering, also showed that significant transient crosslinks arose between the PS chains when the silver salts were added to the PS matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2263–2269, 2004     

Facile method to prepare monodispersed Ag/polystyrene composite microspheres and their properties

This article presents a facile method to prepare silver/polystyrene composite microspheres. In this approach, monodispersed polystyrene (PS) particles were synthesized with carboxyl acid groups on the surfaces of the PS particles via dispersion polymerization at first. With the addition of [Ag(NH₃)₂]⁺ to the PS dispersion, [Ag(NH₃)₂]⁺ was absorbed to the surfaces of the PS particles, and then by heating the system, [Ag(NH₃)₂]⁺ complex ions were reduced to silver to form the Ag/PS composite microspheres. In the synthesis of PS dispersion, PVP was used as dispersant to stabilize the PS particles, it also acted as reducing agent in the reduction of [Ag(NH₃)₂]⁺ complex ions to silver, so no additional reducing agent was needed. The resulting composite microspheres were characterized by TEM, SEM, XPS, and XRD. The catalytic properties and surface‐enhance Raman scattering (SERS) was studied as well. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4547–4554, 2009     

Thin films of PS/PS‐b‐pnipam and ps/pnipam polymer blends with tunable wettability

We developed thin films of blends of polystyrene (PS) with the thermoresponsive polymer poly(N‐isopropylacrylamide) (PNIPAM) (PS/PNIPAM) and its diblock copolymer polystyrene‐b‐poly(N‐isopropylacrylamide) (PS/PS‐b‐PNIPAM) in different blend ratios, and we study their surface morphology and thermoresponsive wetting behavior. The blends of PS/PNIPAM and PS/PS‐b‐PNIPAM are spin‐casted on flat silicon surfaces with various drying conditions. The surface morphology of the films depends on the blend ratio and the drying conditions. The PS/PS‐b‐PNIPAM films do not show an increase in their water contact angles with temperature, as it is expected by the presence of the PNIPAM block. All PS/PNIPAM films show an increase in the water contact angle above the lower critical solution temperature of PNIPAM, which depends on the ratio of PNIPAM in the blend and is insensitive to the drying conditions of the films. The difference between the wetting behavior of PS/PS‐b‐PNIPAM and PS/PNIPAM films is due to the arrangement of the PNIPAM chains in the film. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 670–679