悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

苯乙烯-甲基丙烯酸甲酯悬浮-乳液复合聚合过程中聚合物复合粒子组成的变化

采用苯乙烯(St)悬浮聚合过程中滴加甲基丙烯酸甲酯(MMA)乳液聚合组分,悬浮乳液复合聚合(SECP)方法,制备大粒径聚苯乙烯聚甲基丙烯酸甲酯(PS- PMMA)复合粒子.采用FTIR、1H- NMR、13C- NMR分析方法,研究SECP各个时期复合粒子中MMA- St链节摩尔比,发现悬浮粒子中MMA St链节摩尔比逐渐增大,而PMMA乳胶粒子中逐渐减少,表明悬浮相和乳液相间存在物质传递过程.悬浮粒子中MMA链节质量与MMA总投料质量比主要由乳胶粒子生成速率和乳胶粒子向悬浮粒子凝聚速率决定.最终得到的复合粒子除含PS和PMMA均聚物外,还含少量MMA-St共聚物.     

单体极性对甲基丙烯酸甲酯/丙烯酸丁酯/甲基丙烯酸钠无皂乳液共聚合的影响

研究了少量甲基丙烯酸钠（ＮａＭＡ）存在下单体极性对甲基丙烯酸甲酯（ＭＭＡ）／丙烯酸丁酯（ＢＡ）无皂乳液共聚合的影响．单体极性降低，使粒径减小、聚合速率提高、乳液表面张力和粘度降低、粒子表面电荷密度增大、聚合物分子量提高．ＭＭＡ／ＮａＭＡ无皂乳液聚合物只呈现一个玻璃化温度Ｔｇ，ＢＡ／ＮａＭＡ无皂乳液聚合物呈现两个Ｔｇ，ＭＭＡ／ＢＡ比为２∶１～１∶２的ＭＭＡ／ＢＡ／ＮａＭＡ无皂乳液聚合物呈现四个Ｔｇ，这是由于粒子外面相对富含ＯＳＯ－３和ＣＯＯ－基聚合物的亚层溶解了较多的水，使ＢＡ向粒子中心扩散，ＭＭＡ向外扩散，造成组成差异和相分离而引起的．     

Living Ab Initio Emulsion Polymerization of Methyl Methacrylate in Water Using a Water‐Soluble Organotellurium Chain Transfer Agent under Thermal and Photochemical Conditions

Ab initio emulsion polymerization of methyl methacrylate (MMA) using a water‐soluble organotellurium chain transfer agent in the presence of the surfactant Brij 98 in water is reported. Polymerization proceeded under both thermal and visible light‐irradiation conditions, giving poly(methyl methacrylate) (PMMA) with controlled molecular weight and low dispersity (?<1.5). Despite the formation of an opaque latex, the photoactivation of the organotellurium dormant species took place efficiently, as demonstrated by the quantitative monomer conversion and temporal control. Control of polymer particle size (PDI<0.030) was also achieved using a semi‐batch monomer addition process. The PMMA polymer in the particles retained high end‐group fidelity and was successfully used for the synthesis of block copolymers.     

种子乳液聚合法制备多孔乳胶粒

用批量乳液聚合法制备了苯乙烯（Ｓｔ）———甲基丙烯酸甲酯（ＭＭＡ）二元共聚种子乳液Ｓ１以及Ｓｔ ＭＭＡ 丙烯酸（ＡＡ）三元共聚种子乳液Ｓ２,通过连续法无皂种子乳液聚合合成了一系列不同ＡＡ或ＭＡＡ（甲基丙烯酸）含量的Ｓｔ、ＭＭＡ三元共聚乳液．将所得复合胶乳进行碱／酸分步处理,得到具有多孔结构的乳胶粒．用透射电镜对胶粒形态进行了表征,考察了不饱和酸种类和用量、碱处理初始ｐＨ值及溶胀剂对胶粒成孔的影响．     

Process parameters and their effect on grafting reactions in core/shell latexes

The grafting of methyl methacrylate (MMA) onto polybutadiene (PB) latexes prepared by seeded emulsion polymerization at 50°C was investigated as a function of: (a) initiator concentration used in the secondary polymerization, (b) monomer-to-polymer ratio, (c) the specific surface area of the seed latex, and (d) the degree of conversion. The thin layer chromatography/flame ionization detection (TLC/FID) technique was used to determine the proportion of graft copolymer in the core/shell latex, It was found that grafting PMMA onto PB depended upon the concentration of initiator, decreasing as the concentration was increased. The amount of grafting increased with increasing specific surface area of the seed latex, while the molecular weight of the acetone-soluble graft copolymer decreased. The amount of graft copolymer was found to decrease concurrently with increasing monomer-to-polymer ratio and degree of conversion. These results suggest a hydrogen abstraction mechanism in the formation of graft PB–PMMA through a chain transfer process.     

Influence of hydrophobic monomers on secondary nucleation of hydroxyl‐functionalized latexes

The influence of butyl acrylate (BA) and methyl methacrylate (MMA) on hydroxyl functionalized latexes was investigated. The hydrophobicity of the monomer feed was varied via the BA/MMA ratio. In addition to monitoring the effect of hydrophobic monomer feed on secondary nucleation, the polymerization kinetics and final latex properties were also obtained for comparison. Five different BA to MMA molar ratios were combined with five 2‐hydroxyethyl methacrylate (HEMA) concentrations (0, 10, 20, 30 and 40 mol% in monomer composition). All latexes were synthesized through seeded semibatch emulsion polymerization process. Particle size distributions and average particle sizes of the latexes were determined by dynamic light scattering (DLS) and qualitatively compared with transmission electron microscope (TEM) images. The BA to MMA ratio significantly influences the boundary HEMA concentration at which homogeneous secondary nucleation occurs. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2190–2202     

聚甲基丙烯酸甲酯/聚甲基丙烯酸-2-羟乙酯复合微球的合成及药物吸放性能

采用在甲基丙烯酸甲酯（MMA）悬浮聚合过程中滴加甲基丙烯酸-2-羟乙酯（HEMA）乳液聚合组分的悬浮-乳液耦合聚合方法,制备了大粒径聚甲基丙烯酸甲酯／聚甲基丙烯酸-2-羟乙酯（PMMA／PHEMA）复合微球。PMMA／PHEMA复合微球表面以HEMA乳液聚合物为主,且具有微孔结构。PMMA／PHEMA复合微球在水和苄醇中的平衡溶胀率大于PMMA微球。PMMA／PHEMA复合微球48h异丁苯丙酸负载百分比为35．6％,PMMA为27．6％。在磷酸盐缓冲液中释放时间达到360h,释放量占负载总量的82％;而PMMA微球的释放时间为216h,释放量仅占负载总量的60％。     

Preparation and Characterization of Polymer Core Shell Latex Particles

Stable core‐shell latex was synthesized by semicontinuous seeded emulsion polymerization with core monomers consisting of styrene (St), butyl acrylate (BA), and shell monomers consisting of methyl methacrylate (MMA), eutyl acrylate (EA), and methacrylic acid (MAA). The effects of compound emulsifier amount, mass ratio of anionic/nonionic emulsifier, and initiator amount on latex performance were investigated. By particle size analysis and transmission electron microscopy (TEM) observation, results suggest that final latex particles have clearly core shell structures.     

新型乳液聚合制备疏松PMMA树脂及成粒机理

采用以水相为分散相、甲基丙烯酸甲酯 (MMA) 环己烷混合物为连续相的新型乳液聚合制备PMMA树脂 .发现 ,在未加乳化剂和加入少量Tween2 0乳化剂时 ,均可制备由初级粒子凝聚而成、无明显皮膜结构的疏松PMMA粒子 ,初级粒子粒径小于环己烷存在下MMA悬浮聚合得到的PMMA粒子的初级粒子 .根据聚合体系相构成、PMMA在MMA 环己烷混合液的溶解性及PMMA粒子粒径分布和形态的演变 ,提出了在分散水滴内乳液聚合形成初级粒子 生长 凝聚的新型乳液聚合成粒机理     

Preparation of CO2/N2‐Triggered Reversibly Coagulatable and Redispersible Polyacrylate Latexes by Emulsion Polymerization Using a Polymeric Surfactant

We report here a novel approach for making reversibly coagulatable and redispersible polyacrylate latexes by emulsion (co)polymerization of methyl methacrylate (MMA) using a polymeric surfactant, poly(2‐(dimethylamino)ethyl methacrylate)₁₀‐block‐poly(methyl methacrylate)₁₄. The surfactant was protonated with HCl prior to use. The resulted PMMA latexes were readily coagulated with trace amount of caustic soda. The coagulated latex particles, after washing with deionized water, could be redispersed into fresh water to form stable latexes again by CO₂ bubbling with ultrasonication. The recovered latexes could then be coagulated by N₂ bubbling with gentle heating. These coagulation and redispersion processes were repeatable by the CO₂/N₂ bubbling.     

无乳化剂乳液聚合法合成单分散大粒径高分子微球的研究

无乳化剂乳液聚合法合成单分散大粒径高分子微球的研究朱世雄杜金环金熹高陈柳生（中国科学院化学研究所北京１０００８０）关键词无乳化剂乳液聚合，单分散，均相成核，低聚物胶束微米级大粒径单分散高分子微球在标准计量、情报信息、分析化学等许多领域都有广泛的...     

Butyl acrylate/methyl methacrylate latexes: adhesive properties

In this study, butyl acrylate/methyl methacrylate (BA/MMA) latexes of bimodal molecular weight and particle size distribution were prepared in a multi-step process by seeded conventional emulsion and seeded miniemulsion polymerization. For the conventional emulsion case, a BA/MMA batch copolymerization was conducted as a first step (seed generation) and was followed by a monomer addition step to ensure particle growth. In a third step, a BA/MMA pre-emulsified mixture was added to generate a second particle population. For the miniemulsion case, a BA/MMA copolymerization was carried out as a first step (seed generation) and was followed by a monomer addition step. The addition of a BA/MMA miniemulsion served to generate a bimodal particle size and molecular weight distribution. The final latexes were coated onto a polyethylene terephthalate carrier, dried and their performance as pressure-sensitive adhesives was evaluated using tack, peel and shear adhesion measurements. Structure-property relationships between the adhesive properties and the weight-average molecular weight and average particle size were examined. Even though the polymers obtained by miniemulsion showed better shear resistance, their shear resistance was low. There was no statistically significant difference in peel resistance of the polymers obtained by the two reactions. While a significant difference in tackiness between the two emulsion procedures was found when the adhesives were tested using the less sensitive, rolling ball test, no differences were found when they were tested using a loop tack test.     

Polar Gradient Latex Particles with Hydrophilic Core and Hydrophobic Shell Prepared via Multistep Emulsion Polymerization

Monodisperse polar gradient particles were synthesized via a three‐step emulsion polymerization using poly(butyl acrylate‐methyl methacrylate‐methacrylic acid‐ethylene glycol dimethacrylate) (P(BA‐MMA‐MAA‐EGDMA)) as core, poly(methyl methacrylate‐methacrylic acid‐styrene) (P(St‐MMA‐MAA)) as interlayer and polystyrene (PSt) as shell. The particle growth and encapsulation in each emulsion polymerization step were followed by transmission electron microscopy (TEM), dynamic light scattering (DLS) and conductometric titration. Results indicated that the feeding mode and the interlayer were essential to prepare the polar gradient latex particles with hydrophilic core and hydrophobic shell. The morphologies of the two‐layer core/interlayer and three‐layer core/interlayer/shell particles were observed in TEM micrographs, and the sequential encapsulations of the carboxyl‐containing core and the core/interlayer particles were confirmed by an increase in the particle size as well as an increase in the buried carboxyl percentage.     

Morphology and grafting reactions in core/shell latexes

The particle morphology and percent grafting were investigated as a function of the crosslink density of the seed latex in two systems of core/shell latexes of polybutadiene/polymethyl methacrylate (PB/PMMA) and styrene–butadiene rubber/polymethyl methacrylate (SBR/PMMA) prepared by seeded emulsion polymerization at 50°C. The thin layer chromatography/flame ionization detection (TLC/FID) technique was used to characterize the grafting efficiency of the core/shell latexes. The percent grafting of the shell polymer was found to decrease with increasing the crosslink density of the core material. The particle morphology and precent grafting were also investigated as a function of composition and structure of the core material in four core/shell latex systems: polybutadiene/styrene–acrylonitrile copolymer (PB/SAN), (styrene-butadiene) random copolymer/styrene acrylonitrile copolymer (S:B/SAN), polystyrene : polybutadiene/styrene-acrylonitrile copolymer (PS:PB/SAN) and Kraton/styrene-acrylonitrile copolymer (Kraton/SAN), which were prepared by direct emulsification for the seed followed by emulsion polymerization at 70°C for the shell polymer. Grafting and crosslinking of the core material were found to be competitive reactions depending on the microstructure of the seed latex.     

The influence of the arrangement of styrene in methyl methacrylate/butadiene/styrene on the properties of PMMA/SAN/MBS blends

A series of methyl methacrylate‐butadiene‐styrene (MBS) core–shell impact modifiers were prepared by grafting styrene (St) and methyl methacrylate (MMA) onto polybutadiene (PB) or styrene‐butadiene rubber (SBR) seed latex in emulsion polymerization. All the MBS modifiers were designed to have the same total chemical composition, and Bd/St/MMA equaled 39/31/30, which was a prerequisite for producing transparent blends with poly(MMA)/styrene‐acrylonitrile (PMMA/SAN) matrix copolymers. Under this composition, different ways of arrangement for styrene in MBS led to the different structure of MBS modifier. The concentration of PB or SBR rubber of MBS in PMMA/SAN/MBS blends was kept at a constant value of 15 wt.%. The effects of arrangement of St in MBS on the mechanical and optical properties of PMMA/SAN/MBS blends were investigated. The results indicated that Izod impact strength of PMMMA/SAN/MBS blend with the amount of St grafted on core in MBS was higher than that of blend with the amount of St copolymerized with Bd in core of MBS, while the transparency of blend is opposite. From transmission electron microscopy, it was found that the arrangement of St in MBS influenced the dispersion of blend, which led to different toughness. Copyright © 2013 John Wiley & Sons, Ltd.     

丙烯酸酯纳米乳液的制备与表征

将甲基丙烯酸羟乙酯(HEMA)与甲基丙烯酸(MAA)或丙烯酸(AA)用作甲基丙烯酸甲酯(MMA)／丙烯酸丁酯(BA)乳液聚合体系的反应性助乳化剂，采用一种改进的微乳液聚合方法，合成了高单体／乳化剂比例(大于40：1)的聚丙烯酸酯纳米乳液．讨论了引发剂、乳化剂、助乳化别对乳胶粒大小和胶膜吸水率的影响，并对乳液的流体力学行为，共聚物的拉伸行为及耐水性等进行了研究．     

Emulsion polymerization of styrene and methyl methacrylate using a hydrophobically modified inulin and comparison with other surfactants

The use of a new class of graft polymer surfactants, based on inulin, in emulsion polymerization of poly(methyl methacrylate) (PMMA) and polystyrene (PS) particles is described. PS and PMMA were synthesized by emulsion polymerization, and stable particles with a high monomer content (50 wt %) were obtained with a very small amount of polymeric surfactant ([surfactant]/[monomer] = 0.0033). The latex dispersions were characterized by dynamic light scattering and by transmission electron microscopy to obtain the average particle size and the polydispersity index, and the stability was determined by turbidimetry measurements and expressed in terms of critical coagulation concentration. The last section gives a comparison of PMMA particles prepared by emulsion polymerization using classical surfactants from different types as emulsifiers with that obtained using the copolymer surfactant. It shows the superiority of INUTEC SP1 as it is the only one that allows stable particles at 20 wt % monomer content, with a smaller ratio [surfactant]/[monomer] = 0.002.     

Preparation of Al(OH)3/PMMA nanocomposites by emulsion polymerization

Al(OH)₃/PMMA nanocomposites were prepared by the emulsion polymerization of methyl methacrylate (MMA) in the presence of surface‐functionalized Al(OH)₃ particles. Nanosized Al(OH)₃ particles were previously functionalized with a silane coupling agent, 3‐(trimethoxysilyl) propyl methacrylate (γ‐MPS), which was confirmed by FT‐IR and XRF analysis. The average size of seed particles was around 70 nm, and the density of the coupling agent on the particles was calculated to be 8.9 µmol m^?2. The emulsion polymerization was attempted at relatively high solid content of 40–46 wt%. The ratio of the seed particles to MMA had a strong influence on the stability of latex as well as the morphology of composites. Nanocomposites where several PMMA nodules were attached on the surface of Al(OH)₃ core were produced with stable latex emulsion when the weight percents of Al(OH)₃ to MMA were below 20. In the case of higher ratio of 30%, however, the latexes became unstable with an aggregation, and the product morphology was in the shape of large composite. Thermogravimetric analysis showed an improved thermal stability of PMMA composites with the incorporation of Al(OH)₃ nanoparticles. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis of poly(methyl methacrylate) nanocomposites via emulsion polymerization using a zwitterionic surfactant

The synthesis of nanocomposites via emulsion polymerization was investigated using methyl methacrylate (MMA) monomer, 10 wt % montmorillonite (MMT) clay, and a zwitterionic surfactant octadecyl dimethyl betaine (C18DMB). The particle size of the diluted polymer emulsion was about 550 nm, as determined by light scattering, while the sample without clay had a diameter of about 350 nm. The increase in the droplet size suggests that clay was present in the emulsion droplets. X-ray diffraction indicated no peak in the nanocomposites. Transmission electron microscopy showed that emulsion polymerization of MMA in the presence of C18DMB and MMT formed partially exfoliated nanocomposites. Differential scanning calorimetry showed an increase of 18 degrees C in the glass transition temperature (Tg) of the nanocomposites. A dynamic mechanical thermal analyzer also verified a similar Tg increase, 16 degrees C, for the partially exfoliated nanocomposites over poly(methyl methacrylate) (PMMA). Thermogravimetric analysis indicated a 37 degrees C increase in the decomposition temperature for a 20 wt % loss. A PMMA nanocomposite with 10 wt % C18DMB-MMT was also synthesized via in situ polymerization. This nanocomposite was intercalated and had a Tg 10 degrees lower than the emulsion nanocomposite. The storage modulus of the partially exfoliated emulsion nanocomposite was superior to the intercalated structure at higher temperatures and to the pure polymer. The rubbery plateau modulus was over 30 times higher for the emulsion product versus pure PMMA. The emulsion technique produced nanocomposites of the highest molecular weight with a bimodal distribution. This reinstates that exfoliated structures have enhanced thermal and mechanical properties over intercalated hybrids.