Low-temperature synthesis of supported hydrodesulfurization catalysts based on chevrel phases

A new method has been developed for the synthesis of finely dispersed, highly active, supported hydrodesulfurization catalysts based on Chevrel phases. It is hypothesized that the modification of MoS₂ with cobalt or nickel, which enhances the catalytic activity, and the same modification of Chevrel-type systems are of the same nature. The modifiers act through electron density donation into the conduction band of the active component. The increase in catalytic activity is due to the decrease of the effective charge of the molybdenum ion. The catalysts undergo partial restructuring during the reaction.     

Cu-Co-Fe oxide catalysts supported on carbon nanotubes for the oxidation of CO

The catalytic activity and adsorption characteristics of the surface of catalysts in the form of carbon nanotubes produced on nickel and cobalt oxides with the Cu-Co-Fe oxide system as supported active phase were studied. At carbon nanotubes produced on nickel oxide with (10 + 10) wt.% of the catalytically active phase total conversion of CO to CO₂ is realized at 47 °C. This sample has high specific surface area and a large volume of mesopores. It was shown that the increase in catalytic activity correlates with the increase in the amount of the α₂ form of CO₂. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 42, No. 4, pp. 222–226, July–August, 2006.     

Synthesis of Triple‐Layered Ag@Co@Ni Core–Shell Nanoparticles for the Catalytic Dehydrogenation of Ammonia Borane

Triple‐layered Ag@Co@Ni core–shell nanoparticles (NPs) containing a silver core, a cobalt inner shell, and a nickel outer shell were formed by an in situ chemical reduction method. The thickness of the double shells varied with different cobalt and nickel contents. Ag_0.04@Co_0.48@Ni_0.48 showed the most distinct core–shell structure. Compared with its bimetallic core–shell counterparts, this catalyst showed higher catalytic activity for the hydrolysis of NH₃BH₃ (AB). The synergetic interaction between Co and Ni in Ag_0.04@Co_0.48@Ni_0.48 NPs may play a critical role in the enhanced catalytic activity. Furthermore, cobalt–nickel double shells surrounding the silver core in the special triple‐layered core–shell structure provided increasing amounts of active sites on the surface to facilitate the catalytic reaction. These promising catalysts may lead to applications for AB in the field of fuel cells.     

负载Ni催化剂用于乙二醇蒸汽重整制氢催化性能研究

采用等体积浸渍法和共沉淀法制备了Ni催化剂,在固定床反应器上考察了Ni负载量、焙烧温度、反应温度等因素对乙二醇低温重整制氢反应活性和选择性的影响。应用X射线衍射、氮物理吸附、H₂程序升温还原等技术对负载型Ni催化剂进行了表征。结果表明,共沉淀法制备的Ni/CeO₂催化剂具有较小的NiO颗粒与CeO₂载体颗粒粒径,催化活性较高。添加少量氧化钴到Ni/CeO₂催化剂中可使H₂收率达72.6%,EG转化率达93.1%。在CeO₂中添加Al₂O₃能提高负载Ni催化剂的活性,乙二醇转化率达94.0%,H₂收率达67.0%;但添加SiO₂则使其活性明显变差。     

Potassium Ferrites Formation in Promoted Hematite Catalysts for Dehydrogenation. Thermal and structural analyses

K-promoted hematite catalysts for ethylbenzene dehydrogenation were studied by thermal analysis (TG/DTG) and high-temperature XRD. The formation of potassium ferrite (K₂Fe₂O₄), considered to be a catalytically active phase, was observed during calcination of the Ce-promoted catalysts. A linear correlation of the catalytic activity and the temperature of potassium ferrites formation was found. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effect of gamma-irradiation on surface and catalytic properties of Co3O4 and NiO catalysts

The effects of g-irradiation (0.2-1.6 MGy) on the particle size, specific surface area and catalytic activity of Co₃O₄ and NiO solids were investigated. The investigated solids were prepared by heat treatment of cobalt carbonate at 500 and 700 °C and basic nickel carbonate at 400 °C. The techniques employed were XRD, nitrogen adsorption at -196 °C and decomposition of H₂O₂ at 30-50 °C. The results showed that g-irradiation resulted in a small decrease in the particle size of the investigated solids and effected a progressive increase in their specific surface areas. On the other hand, the exposure of Co₃O₄ and NiO catalysts to a dose of 0.2 MGy resulted in a significant decrease in their catalytic activities, which suffered further progressive decrease upon increasing the doses up to 1.6 MGy. Gamma-irradiation did not modify the activation energy of the catalyzed reaction but decreased the concentration of catalytically active sites without changing their energetic nature. These results were discussed in terms of splitting of the particles of the treated solids and removal of chemisorbed species present in nonstoichiometric cobalt and nickel oxides.     

The hydrodesulfurization activity and characterization of cobalt Chevrel phase sulfides

Hydrodesulfurization activity of cobalt Chevrel phase sulfide catalysts has been investigated in a fixed-bed flow reactor. Single phase cobalt Chevrel phase sulfides exhibited catalytic activity for hydrodesulfurization. Supported cobalt Chevrel phase sulfides catalysts indicated much higher hydrodesulfurization activity and even higher than commercial CoMoS/Al₂O₃ catalysts. The existence of Mo₆S₈ and the reduced oxidation state of Mo in the cobalt Chevrel phase sulfides has been observed by XRD, LRS, and XPS. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis,characterization and catalytic studies of iron(III), cobalt(II), nickel(II) and copper(II) complexes containing triphenylphosphine and β-diketones

A series of new β-diketonato complexes have been synthesized from the reactions of iron(III), cobalt(II), nickel(II) and copper(II) Ph₃P complexes with β-diketones (acetylacetone, benzoylacetone and dibenzoylmethane). All the complexes have been characterized by elemental analyses, spectral studies (i.r., electronic., magnetic., e.p.r., ¹H-n.m.r.) and cyclic voltammetry. The new complexes have been used as catalysts for aromatic coupling and oxidation reactions. Higher catalytic activity has been observed for the nickel(II) complexes compared to the other complexes.     

Effects of the preparation methods on the properties of Ni-La2O3-SiO2 catalysts for m -dinitrobenzene hydrogenation

Ni-La₂O₃-SiO₂ catalysts were prepared by wetness impregnation and sol-gel method followed by conventional drying and supercritical drying, respectively. Their physico-chemical properties and activity for the hydrogenation of m-dinitrobenzene to m-phenylenediamine were investigated by BET, XRD, TPR, H₂-TPD and activity tests. The results showed that the structural and catalytic properties of the Ni-La₂O₃-SiO₂ catalysts obviously depended on the preparation method and the drying mode. The catalyst prepared by the sol-gel method in combination with conventional drying exhibited the highest catalytic activity among the catalysts tested, attributable to its well-dispersed nickel particles and larger active nickel surface area.     

Dehydrogenation of isopropanol on a cerium-nickel catalyst

The effect of a cerium additive on the catalytic activity of a 2 wt % Ni/SiO₂ catalyst is studied. It found that under both flow and static conditions the activity of (2 wt % Ni + 0.2 wt % Ce)/SiO₂ catalyst is higher than that of the original sample; the increase in activity results from a sharp increase in the number of active sites. A change in the composition of the surface layer of the catalysts is analyzed by X-ray photoelectron spectroscopy. It was found that the fraction of nickel decreases and the fraction of carbon increases in cerium-containing catalyst. An explanation of the change in the elemental composition of the catalytic active sites of a nickel catalyst in the presence of cerium is proposed on the basis of XPS data and previous quantum chemical calculations.     

Vergleichende Untersuchungen zur katalytischen Aktivität von Nickel und kristallinen Nickelboriden sowie RANEY-Nickel und borhaltigem RANEY-Nickel: Hydrierungs- und Dehydrierungsreaktionen,elektrochemische Methanoloxydation

The catalytic activation of the decomposition of gaseous formic acid with nickel powder and crystalline nickel borides is compared. Only after treatment with NH₃-solution the activity of the nickel borides has the same order as that of nickel powder. Ni₃B is the best of the catalysts used. The crystalline nickel borides cannot catalyze the anodic oxydation of methanol in alcaline solution at 80°C. — Nickel catalysts containing Boron can be prepared by the RANEY method from nickel boride and aluminum. These catalysts have the same activity as normal RANEY nickel with respect to the hydrogenation of the C?C? bond in crotonic acid; they are more active with respect to the C?O? bond of acetone. Methanol can be oxydised fastly in alcaline solution at 80°C on electrodes containing RANEY nickel. RANEY nickel containing boron is still better.     

Cu_xCo_(1-x)/Al_2O_3/FeCrAl整体式催化剂上甲苯催化燃烧(英文)

以FeCrAl合金薄片为基底,Al2O3浆料为过渡胶体,不同摩尔比的Cu、Co为催化活性组分,制备了一系列CuxCo1-x/Al2O3/FeCrAl(x=0-1)新型整体式催化剂.采用X射线粉末衍射(XRD),扫描电子显微镜(SEM),X光电子能谱(XPS)和程序升温还原(TPR)等手段对催化剂的结构进行了表征.在微型固定床反应器上评价了催化剂的催化甲苯燃烧性能.研究结果表明:在所制备的整体式催化剂上,当Cu含量比较低时,形成了Cu-Co-O固溶体;当Cu含量比较高时,可以测得CuO的衍射峰.催化剂表面颗粒大小和形貌与Cu、Co摩尔比密切相关.在催化剂表面,Co以Co2+和Co3+价态存在,而Cu主要以Cu2+价态存在.催化剂中的Cu可以改善Co的氧化还原性,从而有利于催化剂活性的提高.在所制备的催化剂中,Cu0.5Co0.5/Al2O3/FeCrAl催化剂具有最好的活性,甲苯在374oC可以完全催化燃烧消除.     

Highly stable and selective Ru/NiFe_2O_4 catalysts for transfer hydrogenation of biomass-derived furfural to 2-methylfuran

Spinel ferrites NiFe_2O_4 supported Ru catalysts have been prepared via a simple sol–gel route and applied for converting biomass-derived furfural to 2-methylfuran. The as-prepared catalysts were characterized by thermogravimetric analysis(TG), N_2 adsorption–desorption, X-ray diffraction(XRD), scanning electronic microscopy(SEM), and X-ray photoelectron spectroscopy(XPS). Results showed that the catalysts had well-dispersed Ru active sites and large surface area for calcination temperature ranging from 300 to 500 ℃. The conversion of biomass-derived furfural into 2-methylfuran was conducted over Ru/NiFe_2O_4 through catalytic transfer hydrogenation in liquid-phase with 2-propanol as the hydrogen source. A significantly enhanced activity and increased 2-methylfuran yield have been achieved in this study. Under mild conditions(180 ℃ and 2.1 MPa N_2), the conversion of furfural exceeds 97% and 2-methylfuran yield was up to 83% over the catalyst containing 8 wt% Ru. After five repeated uses, the catalytic activity and the corresponding product yield remained almost unchanged. The excellent catalytic activity and recycling performance provide a broad prospects for various practical applications.     

Thermal Effects Associated with the Incorporation of Transition Metal Catalysts Inside Alumino-silicate Supports

Kaolinic and bentonitic-clays are selected to prepare transition metals, iron, cobalt and nickel catalysts. The metals are incorporated into two supports through new impregnation technique. The original clays and the prepared catalysts were subjected to different techniques. The crystallite size (X-ray diffraction analysis) increases from iron to cobalt then to nickel upon heating and the increase for bentonitic-catalysts is higher than that for kaolinic-ones. Infrared spectra show the appearance of bands signifying the presence of iron, cobalt and nickel bonded to OH group constituting the silica-silica tetrahedral sheets inside the clay structure. The enthalpy (ΔH) andentropy (ΔS) values (differential scanning calorimetric) are lower for bentonitic-catalysts than for kaolinic-catalysts. Thus, the incorporation of the metal hydroxide in the interlamella of the silicate-silicate bentonite clay structure facilitates the interaction between the unpaired electrons on the adjacent atoms and the support which enables the prepared catalysts to be more active for catalytic conversion. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effects of heat treatment on physicochemical properties of cerium based nickel system

Cerium based nickel catalysts synthesized by impregnation method have been characterized by XRD and TEM techniques. These catalysts can be described as a mixture of nickel oxide and ceria modified by the insertion of a part of nickel in the ceria lattice. The surface and catalytic properties of Ni/Ce mixed oxide solids were determined by nitrogen adsorption at 77 K and catalytic conversion of isopropanol at different temperatures.The results revealed that the heat treatment brought about different modifications in the structural, morphological, surface and catalytic properties of the as synthesized catalysts. From the characterization of the as prepared catalysts, it was concluded that the as prepared catalysts contain highly dispersed NiO, well crystalline NiO and CeO₂ and also Ni–Ce–O solid solution. This treatment led to a slightly increase in the crystallite size of ceria particles. On the other hand, the increase in the heat treatment resulted in an increase in the crystallite size, lattice constant and unit cell volume of nickel oxide. The formation of Ni–Ce–O solid solution with subsequent creation of oxygen vacancies increase as the heat treatment increases. However, the specific surface area, total pore volume and catalytic activity of the investigated system decrease as the preparation temperature increases from 500 to 700 °C. The sintering activation energy of NiO and ceria were found to be 2.8 and 12.7 kJ/mol, respectively.     

Macromolecular metal complexes with memory to the catalyzed substrate

A number of complexing polymers containing carboxylic, phosphorylic, amine, imine and pyridine functional groups have been prepared and their complexes with copper, cobalt and nickel have been obtained. The complexes were prearranged for reactions of liquid phase oxidation and hydrogenation of hydrocarbons by means of formation and subsequent fixation in memory of the catalysts the structure of active centres favorable for catalyzed substrate. It has been shown that the prearranged complexes might ≤remember≥ the structure optimum for the substrate and this leads to an essential increase in catalytic activity and selectivity of the catalysts.     

Liquid Phase Hydrogenolysis of Biomass‐derived Lactate to 1,2‐Propanediol over Silica Supported Cobalt Nanocatalyst

Liquid phase hydrogenolysis of ethyl lactate to 1,2‐propanediol was performed over silica supporting cobalt catalysts prepared by two different methods: precipitation‐gel (PG) technique and deposition‐precipitation (DP) procedure. The cobalt species (Co₃O₄/cobalt phyllosilicate) present in the corresponding calcined PG and DP catalysts were different as a consequence of the preparation methods, and Co OH Co olation and Si O Co oxolation molecular mechanisms were employed to elucidate the chemical phenomena during the different preparation procedures. In addition, the texture (BET), reduction behavior (TPR and in‐situ XRD), surface dispersion and state of cobalt species (XPS), and catalytic performance differ greatly between the samples. Because of small particle size, high dispersion of cobalt species and facile reducibility, the Co/SiO₂ catalyst prepared by precipitation‐gel method presented a much higher activity than the catalyst prepared by deposition‐precipitation method. Metallic cobalt is assumed to be the catalytically active site for the hydrogenolysis reaction according to the catalytic results of both cobalt samples reduced at different temperatures and the structure changes after reaction.     

Effect of group VIII elements on the behavior of Li/CaO catalyst in the oxidative dehydrogenation of ethane

The effect of addition of group VIII elements to Li/CaO on the oxidative dehydrogenation of ethane has been investigated in the range of 550–650°c. Iron, cobalt and nickel promote the reaction. The experiments show that iron and cobalt additives in Li/CaO catalysts mainly increase the catalytic activity. Li/Ni/CaO catalyst gives a high ethane conversion and excellent ethylene selectivity. The results on the catalyst are probably due to coordinative interaction between lithium and nickel. The characteristics of the catalysts revealed by XRD also give evidence that the promotion for both catalytic activity and ethylene selectivity is directly related to the formation of favorable crystal phases.     

An influence of thermal treatment conditions of hydrotalcite-like materials on their catalytic activity in the process of N<Subscript>2</Subscript>O decomposition

Hydrotalcite-like materials containing apart from magnesium and aluminum also copper, cobalt, nickel, and iron were prepared by a co-precipitation method. Thermal transformations of hydrotalcite-like materials were studied by thermal analysis methods as well as XRD, UV–vis–DRS, and XPS measurements of the samples calcined at various temperatures (600, 700, and 800 °C). Calcined hydrotalcites, especially those containing cobalt and copper, were found to be active and selective catalysts of N₂O decomposition. It was shown that an increase in the calcination temperature significantly activated the Co-containing catalysts. Promotion of the samples with potassium resulted in activation of the hydrotalcite-based catalysts.     

Unsupported Molybdenum and Cobalt-Molybdenum Nitrides for Thiophene Hydrodesulfurization

The catalytic activity and the structure of unsupported Mo and CoMo nitrided catalysts were investigated. It was found that the structure and catalytic activity of the nitrided catalysts are influenced by the conditions of nitridation. Molybdenum oxynitrides are more active in hydrodesulfurization (HDS) of thiophene than MoS₂. The addition of cobalt to nitrided Mo improves its HDS activity, however, sulfided CoMo catalyst is still more active than the nitrided one. Synergy between Co and Mo for the nitrided unsupported CoMo catalyst exists at lower degree than for the sulfided form of CoMo.