Multiterawatt laser system based on optical parametric chirped pulse amplification

A compact multiterawatt laser system based on optical parametric chirped pulse amplification is demonstrated. Chirped pulses are amplified from 20 pJ to 900 mJ by two lithium triborate optical parametric preamplifiers and a final KDP optical parametric power amplifier with a pump energy of 5 J at 532 nm from Nd:YAG-Nd:glass hybrid amplifiers. After compression, we obtained a final output of 570-mJ-155-fs pulses with a peak power of 3.67 TW, which is the highest output power from an optical parametric chirped pulse amplification laser, to the best of our knowledge.     

1.5 mJ, 6.4 fs parametric chirped-pulse amplification system at 1 kHz

We demonstrate an optical parametric chirped-pulse amplification (OPCPA) system with the pulse energy of 1.5 mJ at a 1 kHz repetition rate. The newly developed 100 ps Ti:sapphire pump laser system, which was optically synchronized with OPCPA seed pulses, delivered 10 mJ, 400 nm pump pulses. After three-stage parametric amplification, recompression of the amplifier output from 45 ps to 6.4 fs was performed. The pulse width of 6.4 fs is, to our knowledge, the shortest ever obtained by OPCPA, and the average power of 1.5 W (1.5 mJ, 1 kHz) is believed to be the highest among few-cycle OPCPA systems.     

Generation of high-contrast and high-intensity laser pulses using an OPCPA preamplifier in a double CPA, Ti:sapphire laser system

We demonstrate a high-contrast, high-intensity double chirped-pulse amplification (CPA) Ti:sapphire laser system using an optical parametric chirped-pulse (OPCPA) pre- amplifier. By injecting cleaned microjoule seed pulses into the OPCPA, a temporal contrast greater than 10¹⁰ within picosecond times before the main femtosecond pulse is demonstrated with an output pulse energy of 1.7 J and a pulse duration of 30 fs, corresponding to a peak power of 60 TW at a 10 Hz repetition rate. This system uses a cryogenically-cooled Ti:sapphire final amplifier and generates focused peak intensities in excess of 10²⁰ W/cm².     

Femtosecond pulse parametric amplification at narrowband high power gas laser pumping

In ultrashort pulse amplification a narrowband gas pump pulse laser has been used for the first time. An all-stage optical parametric chirped pulse amplifier (OPCPA) was driven by a single-shot iodine photodissociation laser. For the first time a broadband amplification was achieved in potassium dihydrogen phosphate crystal at 800 nm seeding. Ti:sapphire laser pulses stretched from 12.5 fs to 250 ps were amplified and compressed to 27 fs at a 0.5 TW output power. The results suggest using narrowband high power gas lasers as OPCPA drivers to generate petawatt beams.     

Broadband, high gain two-stage optical parametric chirped pulse amplifier using BBO crystals for a femtosecond high-power Ti:sapphire laser system

We design a two-stage non-collinear optical parametric chirped pulse amplifier using BBO crystals for a high-power Ti:sapphire laser system, and numerically analyze the output characteristics of the OPCPA system. We find optimal phase-matching conditions and calculate the parametric gains as a function of pump intensity and interaction length. By constructing a two-stage OPCPA system using two BBO crystals, we obtain 12 mJ output energy corresponding to a high gain of 10⁷, a pulse duration of 37 fs, and a contrast ratio of 5×10⁻⁸.     

Yb:YAG Innoslab amplifier: efficient high repetition rate subpicosecond pumping system for optical parametric chirped pulse amplification

We report on a Yb:YAG Innoslab laser amplifier system for generation of subpicsecond high energy pump pulses for optical parametric chirped pulse amplification (OPCPA) at high repetition rates. Pulse energies of up to 20 mJ (at 12.5 kHz) and repetition rates of up to 100 kHz were attained with pulse durations of 830 fs and average power in excess of 200 W. We further investigate the possibility to use subpicosecond pulses to derive a stable continuum in a YAG crystal for OPCPA seeding.     

Trends in ultrashort and ultrahigh power laser pulses based on optical parametric chirped pulse amplification

Since the proof-of-principle demonstration of optical parametric amplification to efficiently amplify chirped laser pulses in 1992,optical parametric chirped pulse amplification(OPCPA)became the most promising method for the amplification of broadband optical pulses.In the meantime,we are witnessing an exciting progress in the development of powerful and ultrashort pulse laser systems that employ chirped pulse parametric amplifiers.The output power and pulse duration of these systems have ranged from a few gigawatts to hundreds of terawatts with a potential of tens of petawatts power level.Meanwhile,the output pulse duration based on optical parametric amplification has entered the range of fewoptical-cycle field.In this paper,we overview the basic principles,trends in development,and current state of the ultrashort and laser systems based on OPCPA,respectively.     

Generation of high-contrast millijoule pulses by optical parametric chirped-pulse amplification in periodically poled KTiOPO4

A new high-contrast, high-gain optical parametric chirped-pulse amplifier (OPCPA) architecture is demonstrated in periodically poled KTiOPO4 (PPKTP). This architecture overcomes parametric fluorescence contrast limitations of the OPCPA in periodically poled materials. The scheme is based on two passes of a single relay-imaged pump pulse and a free-propagating signal pulse through a 1.5 mm x 5 mm x 7.5 mm PPKTP crystal. The output energy of 1.2 mJ is generated at a center wavelength of 1053 nm by 24 mJ of pump energy. A prepulse contrast level of > 3 x 10(7) was measured with > 10(6) saturated gain in the amplifier. Amplified pulses were compressed to 200 fs. This simple and versatile concept requires only a modest pump energy from a commercial pump laser and represents a possible high-contrast front end for high-energy Nd:glass-based petawatt-class lasers.     

光参量啁啾脉冲饱和放大的增益稳定性

 光参量啁啾脉冲放大（OPCPA）在饱和放大区存在一个增益稳定点，据此设计了一个输出稳定的三级OPCPA系统；第一、二、三级分别选用准相位匹配的周期极化钛氧磷酸钾（PPKTP）晶体、LBO晶体和KDP晶体作为增益介质。饱和放大时，增益随泵浦光强度变化时的增益输出稳定性明显改善，在泵浦光强度抖动低于6%的情况下，各级光参量放大器OPA输出的增益抖动小于1%。前级采用准相位匹配的PPKTP晶体作为增益介质，在远低于破坏阈值的30MW/cm²的泵浦功率密度下，可得到2×10⁵的饱和放大增益和20%的能量转换效率。     

Hundred mJ, sub-picoseconds, high temporal contrast OPCPA/Yb:YAG ceramic thin disk hybrid laser system

The authors have demonstrated an optical parametric chirped-pulse amplification (OPCPA)/Yb:YAG ceramic thin disk hybrid laser system having hundred mJ level pulse energy sub-picosecond pulse duration with high temporal contrast. At an input chirped-pulse energy of 3.8?mJ from an OPCPA preamplifier an output energy of 130?mJ has been generated from multipass diode-pumped Yb:YAG ceramic thin disk amplifier. A recompressed pulse duration of 450?fs with a contrast level of less than 7.2×10^?9 at ?150?ps before the main pulse has been obtained. The contrast level is the highest value achieved in Yb:YAG chirped-pulse amplification (CPA) laser system at 100?mJ level.     

外腔式宽调谐被动调QNd:YVO_4/PPMgLN光学参量振荡器

报道了一个低阈值宽调谐、被动调Q、单谐振掺MgO的周期性极化铌酸锂晶体(PPMgLN)光学参量振荡器。利用被动调Q的Nd:YVO4激光器作为泵浦源,采用外腔结构,在室温下,实现了PPMgLN晶体的准相位匹配光学参量振荡。光参量振荡的阈值仅为0.27W(单脉冲能量4.5μJ、脉宽35ns);在泵浦光为1.35W(脉冲能量8.2μJ、脉宽35ns),PPMgLN周期为31μm时,获得了161.9mW,3.202μm脉冲激光输出;同时获得了98.5mW的1.594μm信号光输出,总的光光转化效率达到19.3%。通过改变晶体的周期,实现了闲频光3.13～4.19μm,信号光1.43～1.65μm的宽带可调谐激光输出。     

Development of a high-contrast,high-peak power,Ti:Sapphire/OPCPA laser system

We report on a high-contrast, high-peak power laser system, which combines both conventional laser amplification and optical parametric chirped pulse amplification (OPCPA) techniques. By employing an OPCPA system after a regenerative amplifier, we have enhanced the prepulse contrast by six orders of magnitude. A prepulse contrast of better than 4.4 × 10^?11 has been measured with a high-energy broadband pulse of 24 mJ at a 10 Hz repetition rate from the OPCPA system. With a subsequent four-pass Ti:sapphire amplifier, we have achieved an amplified energy of 279 mJ and an ultrashort recompressed amplified pulse duration of 23.5 fs. We also discuss the basic design aspects and present our preliminary experimental investigations for higher energy operation to a multijoule.     

High-contrast, high-intensity laser pulse generation using a nonlinear preamplifier in a Ti:sapphire laser system

We report a high-contrast, high-intensity Ti:sapphire chirped-pulse amplification system that incorporates a nonlinear preamplifier based on optical parametric chirped-pulse amplification (OPCPA). By cooling the Ti:sapphire crystal in the final amplifier down to 77 K, the chirped-pulses are amplified to 2.9 J at a 10 Hz repetition rate without a thermal lensing effect. Pulse compression down to 19 fs duration obtained after amplification indicates a peak power of 80 TW. With the OPCPA, the temporal contrast is significantly improved to better than 7x10(-9) in a few picoseconds interval prior to the main laser pulse.     

稳定高质量光参量啁啾脉冲放大系统优化设计

要实现光参量啁啾脉冲放大(OPCPA)系统稳定、高质量输出,需要同时对光参量放大和泵浦光倍频这两个非线性过程进行优化设计。在光参量放大系统优化设计中,建立了描述光参量放大过程的多种简化物理模型;通过模拟泵浦光和信号光口径匹配关系,分析了放大信号光空间两维对称性并提出了优化方法;建立了非线性晶体最佳长度确定及调谐方法,以实现信号光输出高稳定性。在泵浦光倍频系统优化设计过程中,提出应用位相失配法实现稳定倍频输出,研究表明这种方法不仅能实现倍频光能量起伏抖动远远小于基频光能量的起伏抖动,而且能减小泵浦光近场调制度和时间波形调制,极大地改善输出倍频光光束质量,进而提高OPCPA系统输出信号光质量。     

基于光束偏转的扫描式宽带光参量啁啾脉冲放大

光参量啁啾脉冲放大(OPCPA)是超短激光脉冲领域的重要技术之一,增大增益带宽对提高OPCPA的转换效率、实现宽带光参量放大具有重要的意义.本文将光束偏转和非共线OPCPA有机结合,提出了基于光束偏转的扫描式宽带OPCPA模型.分析了通过光束偏转来时刻改变非共线角,以保证各频率成分的相位匹配,从而增大增益带宽的基本原理.采用提出的扫描式宽带OPCPA,针对800 nm中心波长、带宽约为100 nm信号光的光参量放大进行了数值计算.结果表明:经过扫描式OPCPA后,信号光的带宽与放大之前几乎相同,光谱没有窄化;扫描式OPCPA比固定非共线角方式的放大极大地增加了增益带宽和转换效率,实现了宽带的光参量放大;要满足信号光各频率成分的相位匹配,达到最大的增益带宽和转换效率,需要尽量减小加载到钽铌酸钾(KTa_(1-x) Nb_xO_3, KTN)电光晶体上的电压抖动和电压延时.     

Broadband femtosecond OPCPA system driven by the single-shot narrow-band iodine photodissociation laser SOFIA

A two-stage optical parametric amplifier driven by a frequency-tripled beam from the high-energy iodine laser system SOFIA was built. This single-shot Optical Parametric Chirped Pulse-Amplification facility (OPCPA) and the system synchronizing the pump and signal pulses are described in detail. The chirped seed pulse of a Ti:sapphire oscillator running at the central wavelength of 800?nm is amplified in the two-stage (LBO and KDP) optical parametric amplifier over 10⁸ times. The amplified spectral bandwidth of 68?nm corresponds to the pulse duration of 14?fs when a transform-limited pulse is assumed. This implies a compressed pulse of TW power. Systematic gain measurements reveal a good match with the theoretical predictions. Signal and idler beam fluence profiles are presented. The suitability of the iodine photo-dissociation laser as a pump source for the OPCPA technique is thus proved for the first time experimentally. A distinctive feature of the iodine laser is its very narrow gain bandwidth (<0.1?cm^?1) and, therefore, the conventional chirped-pulse amplification technique does not lead to pulse durations at the femtosecond level.     

全光纤多种子激光脉冲产生系统

报道一种可精确同步输出宽带啁啾脉冲、纳秒级整形脉冲以及窄带光参量啁啾放大抽运脉冲的全光纤多种子激光脉冲产生系统.采用掺镱光纤锁模激光器和掺镱单纵模光纤振荡器作为系统的光源,将掺镱光纤锁模激光器输出的超短脉冲分束啁啾展宽至0.9ns后,一路进行放大产生10μJ量级的宽带啁啾脉冲为高能拍瓦激光器系统提供种子光脉冲,另一路通过1.2nm滤波产生140ps的基元脉冲,通过光纤堆积器产生可编程整形的2.3ns脉冲,再经过放大达到10μJ量级,提供任意整形的压缩脉冲.同时,将部分掺镱光纤锁模激光器输出的超短脉冲进行光电转换并锁相后,产生与锁模超短脉冲高精度同步的电脉冲用于触发幅度调制器,将掺镱单纵模光纤振荡器输出的连续光削波放大,产生光参量啁啾放大抽运脉冲.该系统能够根据物理实验的需要,非常灵活地在输出各种脉冲之间做出选择.     

Improvement of contrast ratio in saturated OPCPA system by using pump pulse shaping and time delay control

We theoretically investigated the temporal profile of a background pedestal in a single-stage optical parametric chirped pulse amplification (OPCPA) system, and showed that the amplified spontaneous emission (ASE) prepulse in the saturation regime degrades the contrast ratio. To improve the contrast ratio in a saturated OPCPA system, a method using pump pulse shaping and the time delay control between pump and seed pulses was utilized. Through numerical simulations, the effect of the rising time and the time delay of a pump pulse on the background pedestal was subsequently investigated in terms of the contrast ratio. From the simulation results, it was determined that an optimal rising time and the time delay of the pump pulse are critical for obtaining a high-contrast broadband laser pulse from a saturated OPCPA system.     

High energy and long pulse generation with high-birefringence photonic crystal fibre and laser-diode pumped regenerative amplifier

We report on the generation of a high energy and long pulse for pumping optical parametric chirped-pulse amplification (OPCPA) by a high-birefringence photonic crystal fibre (HB-PCF) and a laser-diode-pumped regenerative chirped pulse amplifier. Using the femtosecond pump pulse centred at 815~nm, a 1064~nm soliton pulse is produced in the HB-PCF. After injecting it into an Nd:YAG regenerative amplifier with the glass etalons, a narrow-band amplified pulse with an energy of $\sim $4~mJ and a duration of 235 ps is achieved at a repetition rate of 10~Hz, which is suitable for being used as a pump source in the 800~nm OPCPA system.     

Injection-Seeded 500 Hz Repetition Rate High Peak Power Single-Frequency Nd:YAG Laser for Mid-Infrared Generation

We develop an injection-seeded single-frequency neodymium-doped yttrium aluminum garnet (Nd:YAG) laser with 500 Hz repetition rate and high peak power. The laser construction is designed as seed injection and master oscillator power amplifier (MOPA) including single-frequency master oscillator, extra-cavity frequency doubling crystal, and round-trip power amplifier. The master oscillator can emit 1,064 nm laser of 8.4 mJ with 6.8 ns pulse width at the pump energy equal to 23 mJ. A green laser energy of 1.1 mJ is obtained by setting the proper temperature of the LBO crystal. The pulse energy of 1,064 nm laser decreases to 6.5 mJ after passing through the LBO crystal and rises to 25.3 mJ after a round-trip power amplifier corresponding to the extraction efficiency of 29%. The final output pulse width is 6.5 ns, representing a peak power of 3.9 MW. The 1,064 nm laser beam quality factor M² of the master oscillator and the amplified one are 1.3 and 1.5, respectively. The laser will be used to generate mid-infrared where the 532 nm laser with narrow pulse width is to pump sheet optical parametric oscillator (OPO) and the 1,064 nm laser with high peak power to pump the OPO.