Cr3+:Al2O3透明多晶陶瓷光谱特性分析

对透光性良好的Cr³⁺:Al₂O₃透明多晶陶瓷的光谱性能 进行了研究，其吸收光谱中吸收峰与单晶红宝石相一致，按吸收光谱和Tanabe-Sugano能级 图，算出其晶场强度参数D_q及Racah参数B分别为1792cm^-1， 689cm ^-1，D_q/B=2.6，陶瓷中Cr³⁺离子所处格位的晶体场强 比单晶弱一些，但Cr³⁺:Al₂O₃透明陶瓷仍属于强场晶 体材料；当Cr³⁺掺杂浓度到达0.8wt%时，陶瓷的发射谱仍保持较好的R线发射 ；随Cr³⁺掺杂浓度的增大，激发峰位发生“红移”.在Cr³⁺:Al₂O₃透明多晶陶瓷的荧光谱上，发现一个波长为670nm的发射峰，经激发 谱确认为Cr³⁺的发射峰. 关键词： 氧化铝 透明陶瓷 离子格位 光谱性质     

Cr3+掺杂的Cd3Al2Ge3O12光谱特性及晶场参数计算

采用高温固相法合成了Cd₃Al₂Ge₃O₁₂：Cr³⁺多晶材料,利用X射线衍射对其结构进行了分析,通过Cr³⁺的室温吸收光谱、室温和77K发射光谱分别对其光谱特性和晶场参数进行了分析和计算.结果表明：在450 nm的蓝光激发下,Cd₃Al₂Ge₃O₁₂：Cr³⁺室温发 关键词： 3Al₂Ge₃O₁₂：Cr³⁺')" href="#">Cd₃Al₂Ge₃O₁₂：Cr³⁺ 荧光光谱 晶场参数 可调谐激光     

Cr4+在八面体格位中的光谱特性研究

采用提拉法生长了Cr单掺和Cr，Mg共掺Al₂O₃晶体，后者具有900—1600nm的宽带吸收.研究了该吸收带在不同气氛、不同温度退火下的变化规律.通过建立合理的晶格缺陷模型，成功地解释了所有的实验结果，并确定Cr，Mg共掺Al₂O₃晶体红外波段宽吸收带属于八面体格位中的Cr⁴⁺离子. 关键词： 4+离子')" href="#">Cr⁴⁺离子 八面体格位 晶格缺陷     

Nd3+掺杂的氧化镧钇透明激光陶瓷的光谱性能研究

采用传统无压烧结工艺制备了Nd³⁺掺杂的Y_2-2xLa_2xO₃(x=0.08)透明陶瓷并对其光谱性能进行了研究. 结果表明：Nd³⁺:Y_1.84La_0.16O₃透明陶瓷在780—850 nm的波长范围内有较宽的吸收带. 当Nd³⁺掺杂量为1.5at%时，在820 nm和激光二极管抽运的808 nm处的吸收截面分别为σ_abs(820 nm)=1.81×10^-20 cm²，σ_abs(808 nm)=1.54×10^-20 cm². 最强的发射峰位于1078 nm处，并具有荧光寿命长、发射带宽宽、量子效率高等特点. 加入La₂O₃后，基质的光谱品质参数X_Nd由1.6减小到0.46，因此和⁴F_3/2—⁴I_11/2跃迁相对应的荧光分支比β_J,11/2增大为56.82%. Nd³⁺:Y_1.84La_0.16O₃透明陶瓷的这些性质有利于高效率的激光输出和超短锁模激光脉冲的实现. 关键词： 氧化镧钇透明陶瓷 光谱性能 3+')" href="#">Nd³⁺     

Y2O3:Yb3+,Tm3+纳米材料的可见及紫外上转换发光

通过燃烧法制备了Yb³⁺-Tm³⁺共掺的Y₂O₃纳米粉体,并对样品在980 nm激光照射下的上转换发光特性进行了研究.实验发现,样品在可见光区域能够产生强烈的蓝色发光(476 nm和487 nm)和较弱的红色发光(约650 nm),而且同时观察到了两个紫外发光峰¹I₆→³H₆ (~297 nm)和^{1关键词： 2O₃:Yb3+')" href="#">Y₂O₃:Yb3+ 3+}')" href="#">Tm³⁺ 上转换光谱 敏化 紫外发光     

自受激拉曼晶体Nd3+:SrMoO4的光谱性质研究

通过拉曼散射光谱，吸收光谱，荧光发射寿命和808 nm LD激发下的红外荧光光谱的实验测量，系统研究了Nd³⁺:SrMoO₄晶体的自受激拉曼光谱性质.分析指认了拉曼散射光谱中各拉曼峰所对应的晶格振动模式，得出了其SRS活性最强的声子频率约为898 cm^-1，对应于(MoO^2-₄)离子团的完全对称光学伸缩振动A_g模；通过J-O理论对晶体的吸收谱进行了全面的光谱参数计算，得出⁴F_3/2→⁴I_11/2跃迁的积分发射截面达0.57×10^-18 cm²，自发辐射概率为141.06 s^-1；同时，实验测得该跃迁的荧光发射寿命约为0.2 ms.最后，结合808 nm LD激发下的红外波段荧光光谱，论证了SrMoO₄晶体中Nd³⁺离子1068 nm发射通过拉曼频移获得1180 nm一级斯托克斯激光发射的可能性，为Nd³⁺:SrMoO₄晶体的自受激拉曼激光器研究提供了理论依据. 关键词： 3+离子')" href="#">d³⁺离子 4 晶体')" href="#">SrMoO₄ 晶体 自受激拉曼散射     

Eu2+,Mn2+在BaZnP2O7中的发光及Eu2+→Mn2+能量传递

采用高温固相法合成了BaZnP₂O₇:Eu²⁺,Mn²⁺荧光粉,并对其发光性质及Eu²⁺对Mn²⁺的能量传递机理进行了研究.Eu²⁺和Mn²⁺在380 nm和670nm的发射峰分别由Eu²⁺的5d—4f跃迁和Mn²⁺的⁴T₁(^{4关键词： 磷酸盐 2+}')" href="#">Eu²⁺ 2+')" href="#">Mn²⁺ 能量传递     

980 nm激发下Er3+/Yb3+共掺杂ZrO2-Al2O3粉末的上转换发光特性

通过固相反应法制备了Er³⁺/Yb³⁺共掺杂ZrO₂-Al₂O₃粉末的样品，并对样品在980nm激光激发下的上转换发光特性进行了研究.从发射光谱可以发现，在可见光范围内有3个强的发光带，一个位于654nm附近的红光带和两个分别位于545nm、525nm附近的绿光带，分别对应于Er³⁺离子的以下辐射跃迁：⁴F_9/2→⁴I_15/2、⁴S_3/2→⁴I_15/2、 ²H_11/2→⁴I_15/2.其中又以Er³⁺离子的⁴F_9/2→⁴I_15/2跃迁产生的红色荧光辐射最强.对其上转换发光机制进行了分析，发现这三个发光过程都是双光子过程.对样品粉末进行了XRD检测，发现ZrO₂主要以立方相为主，并且计算得到了这种立方结构的晶格常数.Al₂O₃固溶于ZrO₂中，Al³⁺嵌入ZrO₂后产生氧空位，导致ZrO₂晶体的对称性降低，这种结构变化更有利于提高上转换效率，即上转换发光强度增强. 关键词： 3+/Yb³⁺')" href="#">Er³⁺/Yb³⁺ 上转换 2-Al₂O₃')" href="#">ZrO₂-Al₂O₃ 荧光 稀土     

多格位阳离子共掺提升LiScSi2O6∶Cr3+近红外荧光粉的光吸收

采用高温固相法制备Na⁺、In³⁺、Ge⁴⁺单掺或共掺杂的LiScSi₂O₆∶Cr³⁺荧光粉,通过漫反射光谱、光致激发和发射光谱、量子效率测试等手段对其光吸收及光致发光性能进行了研究。实验结果表明,Na⁺、In³⁺、Ge⁴⁺等离子单独掺杂均可提升LiScSi₂O₆∶Cr³⁺荧光粉对460 nm蓝光的吸收,而多格位阳离子共掺可进一步增强光吸收能力,吸收效率可从最初的50.5%提升至60.9%。多格位离子单掺或共掺引起Cr³⁺占据八面体结构畸变程度增加,从而导致光吸收增强。优化荧光体系LiSc_0.4In_0.6Si_1.6Ge_0.4O₆∶Cr³⁺的近红外发射峰波长为860 nm,半高...     

Er3+/Yb3+掺杂氟硅铅酸盐微晶玻璃的上转换发光

制备了微晶体尺寸大约在10—12 nm范围内的Er³⁺,Yb³⁺共掺杂透明氟硅铅酸盐微晶玻璃.相同功率激发下,纳米微晶玻璃中Er³⁺离子的²H_11/2,⁴S_3/2→⁴I_15/2的绿色上转换荧光和⁴F_9/2→关键词： 3+')" href="#">Er³⁺ 3+')" href="#">Yb³⁺ 能量传递 纳米微晶玻璃     

Y3Al5O12 ceramic absorbers for the suppression of parasitic oscillation in high-power Nd:YAG lasers

The objective of this study was to identify a material suitable to absorb radiation at the wavelength of neodymium-doped Yttrium Aluminum Garnet (Y₃Al₅O₁₂:YAG), 1064 nm. M-(M= Sm³⁺, Co²⁺, Co³⁺, Cr³⁺, and Cr⁴⁺) doped highly transparent YAG ceramics were fabricated, and their absorption spectra were measured. Unlike Co²⁺ and Cr³⁺-doped ceramic samples, Co³⁺ and Cr⁴⁺ and Sm³⁺-doped:YAG ceramics were found to have significant absorption at 1064 nm. However, the Sm³⁺-doped YAG clearly emerged as the best candidate because it is also transparent at 808 nm, the pumping wavelength laser diode (LD), and also at most absorption bands used for flash-lamp pumping.     

Sm共掺对Sr4Al14O25:M (M=Mn4+, Cr3+）荧光粉发光性能的影响

用固相反应法合成了Sr₄Al₁₄O₂₅:M和Sr₄Al₁₄O₂₅:(M+Sm³⁺)(M=Mn⁴⁺, Cr³⁺)荧光粉, 研究了其发光性能．Sm的共掺并没有改变Sr₄Al₁₄O₂₅:Cr³⁺激发带和发射带的位置, 但是显著提高了材料的发光性能;Sm共掺Sr₄Al₁₄O₂₅:Mn⁴⁺反而降低了发光强度． 对于Cr³⁺, Sm³⁺共掺的Sr₄Al₁₄O₂₅荧光粉, 呈现了从Sm³⁺到Cr³⁺ 的辐射形式的能量传递过程,说明了Sm的共掺对于Sr₄Al₁₄O₂₅:Cr³⁺荧光粉的发光强度提高的原因．     

Dy含量对红色长余辉发光材料Sr3Al2Ｏ6:Eu2＋,Dy3＋性能的影响

采用溶胶凝胶法制备了Sr₃Al₂Ｏ₆:Eu^2＋,Dy^3＋红色长余辉发光材料,利用X射线衍射仪对材料的物相进行了分析,结果表明,1200℃下制备的样品的物相为Sr₃Al₂Ｏ₆,少量的Eu和Dy掺杂没有影响样品的相组成.采用荧光分光光度计、照度计测定了样品的发光特性.结果表明Sr₃Al₂Ｏ关键词： 红色长余辉 3Al₂Ｏ₆')" href="#">Sr₃Al₂Ｏ₆ 溶胶凝胶法     

Optical characteristics of Cr and Nd codoped Y3Al5O12 ceramics

The optical characteristics of Cr³⁺ and Nd³⁺ codoped Y₃Al₅O₁₂ (YAG) ceramics are measured. These measurements are done using two pumping sources, a 808 nm laser diode (LD) and a Xe short-arc lamp, to simulate solar radiation. The specimens used are 0.1%Cr³⁺/1.0%Nd³⁺ and 3.0%Cr³⁺/1.0%Nd³⁺ (atomic%) codoped YAG ceramics. A Nd:YAG crystal doped with 1.0%Nd³⁺ is used as a reference. The saturation intensities of the Cr/Nd:YAG ceramics pumped by the LD are the same as that of the Nd:YAG crystal, while they are higher when they are pumped by the Xe lamp. The saturation intensities are for the 0.1% Cr-doped ceramic and for the 3.0%Cr-doped ceramic. The small signal gains of the 0.1%Cr-doped and 3.0%Cr-doped ceramics are measured and found to be 1.8 times and 7.0 times higher than that of Nd:YAG for the same intensity of solar pumping, respectively. The quantum efficiency of energy transfer from Cr³⁺ to Nd³⁺ is estimated to be 0.88±0.09 for the 0.1%Cr-doped ceramic and 0.67±0.08 for the 3.0%Cr-doped ceramic.     

On the luminescence of bismuth aluminate (Bi2Al4O9)

The luminescence of Eu³⁺ and Tb³⁺ in Bi₂Al₄O₉ is reported. It is shown that the Bi³⁺ excitation energy does not migrate through the lattice. The Cr³⁺ ion shows 704.5 nm line emission in this host lattice.     

Mn, Cr-co-doped MgAl2O4 phosphors for white LEDs

The Mn-, Cr-doped and Mn, Cr-co-doped MgAl₂O₄ powders have been synthesized via a gel-solid reaction method. Energy transfer from Mn²⁺ to Cr³⁺ has been observed for the first time in the co-doped MgAl₂O₄ phosphors. When excited with blue light with a wavelength of 450 nm at room temperature, both green emission from Mn²⁺ around 520 nm and red emission from Cr³⁺ around 675and 693 nm were generated. Moreover, the color of the emission can be modified by controlling the doping concentrations of Mn²⁺ and Cr³⁺. Therefore, MgAl₂O₄: Mn²⁺, Cr³⁺ could be used as a single-phased phosphor for white LED with a blue LED chip. The energy transfer in terms of Mn²⁺ to Cr³⁺ is determined by means of radiation and reabsorption.     

Electron energy loss spectra from polycrystalline Cr and Cr2O3 before and after surface reduction by Ar bombardment

Electron energy loss spectra (ELS) have been obtained from polycrystalline Cr and Cr₂O₃ before and after surface reduction by 2 keV Ar⁺ bombardment. The primary electron energy used in the ELS measurements was systematically varied from 100 to 1150 eV in order to distinguish surface versus bulk loss processes. Two predominant loss features in the ELS spectra obtained from Cr metal at 9.0 and 23.0 eV are assigned to the surface and bulk plasmon excitations, respectively, and a number of other features arising from single electron transitions from both the bulk and surface Cr 3d bands to higher-lying states in the conduction band are also present. The ELS spectra obtained from Cr₂O₃ exhibit features that originate from both interband transitions and charge-transfer transitions between the Cr and O ions as well as the bulk plasmon at 24.4 eV. The ELS feature at 4.0 eV arises from a charge-transfer transition between the oxygen and chromium ions in the two surface layers beneath the chemisorbed oxygen layer, and the ELS feature at 9.8 eV arises from a similar transition involving the chemisorbed oxygen atoms. The intensity of the ELS peak at 9.8 eV decreases after Ar⁺ sputtering due to the removal of chemisorbed oxygen atoms. Sputtering also increases the number of Cr²⁺ states on the surface, which in turn increases the intensity of the 4.0 eV feature. Furthermore, the ELS spectra obtained from the sputtered Cr₂O₃ surface exhibit features characteristic of both Cr⁰ and Cr₂O₃, indicating that Ar⁺ sputtering reduces Cr₂O₃. The fact that neither the surface- nor the bulk-plasmon features of Cr⁰ can be observed in the ELS spectra obtained from sputtered Cr₂O₃ while the loss features due to Cr⁰ interband transitions are clearly present indicates that Cr⁰ atoms form small clusters lacking a bulk metallic nature during Ar⁺ bombardment of Cr₂O₃.     

Awakening the Dumb Site to Realize Ultra-Broadband NIR Phosphor

Near-infrared (NIR) light sources have gained immense popularity in recent years due to their wide range of applications in various fields, including spectroscopy and biomedical imaging. However, the limited emission bandwidth of NIR phosphors is a significant bottleneck in their development. Here, a novel strategy is reported to broaden the emission bandwidth of NIR phosphors by awakening the dumb site. Na₄M₃Ta(PO₄)₆: Cr³⁺ (M = Al³⁺, Ga³⁺, In³⁺) phosphor is synthesized, which exhibits a greatly broadened bandwidth from 134 to 232 nm. Structural and spectral analysis reveals that the NaO₆ octahedral site has a severe t_2g-type distortion, making it a dumb site for Cr³⁺. By introducing larger In³⁺ at the M site, the angular distortion at the NaO₆ site decreases to the normal range, enabling the luminescence of Cr³⁺ again. Along with the broadened bandwidth, the emission peak also redshifts from 802 to 977 nm, giving advantages in NIR spectroscopy applications. Interestingly, the awakened luminescence at the NaO₆ site shows even better luminescence properties than the original M/TaO₆ octahedral site. These findings reveal a novel insight into the luminescence of Cr³⁺ at the octahedral site, which could potentially revolutionize the design of NIR phosphors.     

Blue light emission from Eu ions in sol-gel-derived Al2O3-SiO2 glasses

Blue light-emitting glasses were successfully prepared by doping Eu²⁺ ions in the system Al₂O₃-SiO₂. The Al₂O₃-SiO₂ glasses doped with Eu³⁺ ions were synthesized using a sol-gel method, followed by heating in hydrogen gas atmosphere to reduce into the Eu²⁺ ions. The obtained glasses exhibited emission spectra with peak at ∼450 nm due to 4f⁶5d→4f⁷ (⁸S_7/2) transition, the intensities of which strongly changed depending on their glass composition and heating conditions. The emission quantum efficiency of 48% was achieved by heating the glass with the ratio of Al³⁺ to Eu³⁺ at about 6 at 1000 °C in hydrogen gas atmosphere. It was found that the Al₂O₃-SiO₂ glasses were appropriate not only for homogeneously doping the Eu³⁺ ions in glass structure but also reducing to Eu²⁺ ions, resulting in enhanced blue light-emission properties.