Experimental study of the initial growth of a localized turbulent patch in a stably stratified fluid

We present a laboratory experiment of the initial growth of a turbulent patch in a stably stratified fluid. The patch is created due to a localized source of turbulence, generated by a horizontally oriented and vertically oscillating grid much smaller than the tank size and far from solid boundaries. Synchronized and overlapping particle image velocimetry(PIV) and planar laser induced fluorescence (PLIF) measurements capture the evolution of the patch through its initial growth until it reached a maximum size. The simultaneous measurements of density and velocity fields allow for a direct quantification of the distribution of kinetic energy, buoyancy and degree of mixing within the patch. We can also relate the propagation speed of the turbulent/non-turbulent interface and its thickness to the properties of the turbulent fluid inside the evolving patch. The velocity measurements in this setup indicate significant transient effects inside the patch during its growth. A local analysis of the turbulent/non-turbulent interface provides direct measurements of the entrainment velocity w_e as compared to the local vertical velocity and turbulent intensity at the proximity of the interface. The detailed information about the growth of localized sources of turbulence in stratified environment might be of use in stealth design of autonomous underwater vehicles.     

PIV study of large-scale flow organisation in slot jets

The paper reports on particle image velocimetry (PIV) measurements in turbulent slot jets bounded by two solid walls with the separation distance smaller than the jet width (5–40%). In the far-field such jets are known to manifest features of quasi-two dimensional, two component turbulence. Stereoscopic and tomographic PIV systems were used to analyse local flows. Proper orthogonal decomposition (POD) was applied to extract coherent modes of the velocity fluctuations. The measurements were performed both in the initial region close to the nozzle exit and in the far fields of the developed turbulent slot jets for Re ⩾ 10,000. A POD analysis in the initial region indicates a correlation between quasi-2D vortices rolled-up in the shear layer and local flows in cross-stream planes. While the near-field turbulence shows full 3D features, the wall-normal velocity fluctuations day out gradually due to strong wall-damping resulting in an almost two-component turbulence. On the other hand, the longitudinal vortex rolls take over to act as the main agents in wall-normal and spanwise mixing and momentum transfer. The quantitative analysis indicates that the jet meandering amplitude was aperiodically modulated when arrangement of the large-scale quasi-2D vortices changed between asymmetric and symmetric pattern relatively to the jet axis. The paper shows that the dynamics of turbulent slot jets are more complex than those of 2D, plane and rectangular 3D jets. In particular, the detected secondary longitudinal vortex filaments and meandering modulation is expected to be important for turbulent transport and mixing in slot jets. This issue requires further investigations.     

Highly-resolved LES and PIV Analysis of Isothermal Turbulent Opposed Jets for Combustion Applications

Turbulent opposed jet (TOJ) burners are an interesting test case for fundamental combustion research and a good benchmark for the available modelling approaches. However, these opposed jet flames strongly depend on the turbulence generation inside the nozzle, which is usually achieved through a perforated plate upstream of the nozzle exit. The present work investigates the flow from these perforated plates and the subsequent turbulence generation in great detail. We present results from highly-resolved large eddy simulations (LES) of the in-nozzle flow in turbulent opposed jets alongside state-of-the-art particle image velocimetry (PIV) at standard and high repetition rates taken inside a glass nozzle. The in-nozzle PIV data provides the LES inflow conditions with unprecedented detail, which are used to follow the initial jet development behaviour known from PIV, before jet coalescence, turbulence production and decay further downstream in the nozzles are successfully predicted. In regions where the PIV experiment suffers from inherent limitations like reflections and the velocity bias, the LES data is available to still obtain a detailed picture of the flow. The sensitivity of the simulations to various physical and numerical parameters is discussed in detail. Results from LES and PIV are compared qualitatively and quantitatively in terms of first and second moments of velocity, temporal autocorrelations, and energy density spectra. Significant deviations are found in the frequency (20%) and strength of vortex shedding from the inlet plane only, whereas the qualitative and quantitative agreement between simulation and experiment is otherwise excellent throughout, implying that a successful large eddy simulation of a turbulent opposed jet can be performed in a domain that includes the perforated plates.     

Analysis of a turbulent buoyant confined jet modeled using realizable k–ɛ model

Through this paper, analyses of components of the unheated/heated turbulent confined jet are introduced and some models to describe them are developed. Turbulence realizable k–? model is used to model the turbulence of this problem. Numerical simulations of 2D axisymmetric vertical hot water confined jet into a cylindrical tank have been done. Solutions are obtained for unsteady flow while velocity, pressure, temperature and turbulence distributions inside the water tank are analyzed. For seeking verification, an experiment was conducted for measuring of the temperature of the same system, and comparison between the measured and simulated temperature shows a good agreement. Using the simulated results, some models are developed to describe axial velocity, centerline velocity, radial velocity, dynamic pressure, mass flux, momentum flux and buoyancy flux for both unheated (non-buoyant) and heated (buoyant) jet. Finally, the dynamics of the heated jet in terms of the plume function which is a universal quantity and the source parameter are studied and therefore the maximum velocity can be predicted theoretically.     

Measurements of Turbulent Jet Mixing in a Turbulent Co-Flow Including the Influence of Periodic Forcing and Heating

In this work, the turbulent mixing of a confined coaxial jet in air is investigated by means of simultaneous particle image velocimetry and planar laser induced fluorescence of the acetone seeded flow injection. The jet is injected into a turbulent duct flow at atmospheric pressure through a 90 ^° pipe bend. Measurements are conducted in a small scale windtunnel at constant mass flow rates and three modes of operation: isothermal steady jet injection at a Dean number of 20000 (R e _d =32000), pulsed isothermal injection at a Womersley number of 65 and steady injection at elevated jet temperatures of ΔT=50 K and ΔT=100 K. The experiment is aimed at providing statistically converged quantities of velocity, mass fraction, turbulent fluctuations and turbulent mass flux at several downstream locations. Stochastic error convergence over the number of samples is assessed within the outer turbulent shear layer. From 3000 samples the statistical error of time-averaged velocity and mass fraction is below 1 % while the error of Reynolds shear stress and turbulent mass flux components is in the of range 5-6 %. Profiles of axial velocity and turbulence intensity immediately downstream of the bend exit are in good agreement with hot-wire measurements from literature. During pulsed jet injection strong asymmetric growing of shear layer vortices lead to a skewed mass fraction profile in comparison with steady injection. Phase averaging of single shot PLIF-PIV measurements allows to track the asymmetric shear layer vortex evolvement and flow breakdown during a pulsation cycle with a resolution of 10^°. Steady injection with increased jet temperature supports mixing downstream from 6 nozzle diameters onward.     

Study of Density Effects in Turbulent Buoyant Jets Using Large-Eddy Simulation

Large-Eddy simulations (LES) of spatially evolving turbulent buoyant round jets have been carried out with two different density ratios. The numerical method used is based on a low-Mach-number version of the Navier–Stokes equations for weakly compressible flow using a second-order centre-difference scheme for spatial discretization in Cartesian coordinates and an Adams–Bashforth scheme for temporal discretization. The simulations reproduce the typical temporal and spatial development of turbulent buoyant jets. The near-field dynamic phenomenon of puffing associated with the formation of large vortex structures near the plume base with a varicose mode of instability and the far-field random motions of small-scale eddies are well captured. The pulsation frequencies of the buoyant plumes compare reasonably well with the experimental results of Cetegen (1997) under different density ratios, and the underlying mechanism of the pulsation instability is analysed by examining the vorticity transport equation where it is found that the baroclinic torque, buoyancy force and volumetric expansion are the dominant terms. The roll-up of the vortices is broken down by a secondary instability mechanism which leads to strong turbulent mixing and a subsequent jet spreading. The transition from laminar to turbulence occurs at around four diameters when random disturbances with a 5% level of forcing are imposed to a top-hat velocity profile at the inflow plane and the transition from jet-like to plume-like behaviour occurs further downstream. The energy-spectrum for the temperature fluctuations show both −5/3 and −3 power laws, characteristic of buoyancy-dominated flows. Comparisons are conducted between LES results and experimental measurements, and good agreement has been achieved for the mean and turbulence quantities. The decay of the centreline mean velocity is proportional to x ^−1/3 in the plume-like region consistent with the experimental observation, but is different from the x ⁻¹ law for a non-buoyant jet, where x is the streamwise location. The distributions of the mean velocity, temperature and their fluctuations in the near-field strongly depend upon the ratio of the ambient density to plume density ρ_a/ρ₀. The increase of ρ_a/ρ₀ under buoyancy forcing causes an increase in the self-similar turbulent intensities and turbulent fluxes and an increase in the spatial growth rate. Budgets of the mean momentum, energy, temperature variance and turbulent kinetic energy are analysed and it is found that the production of turbulence kinetic energy by buoyancy relative to the production by shear is increased with the increase of ρ_a/ρ₀. Received 16 June 2000 and accepted 26 June 2001     

Experimental study of thermal mixing layer using variable temperature hot-wire anemometry

The buoyancy effects on the development of the thermal mixing layer downstream from a horizontal separating plate were studied by comparing stable and unstable counter-gradient configurations. In this study, the novel experimental technique called parameterizable constant temperature anemometer, proposed by Ndoye et al. (Meas Sci Technol 21(7):075401, 2010), was improved to make possible the simultaneous measurement of temperature and two velocity components with an x-wire probe. The buoyancy effects on the flow are discussed through the transport equations of turbulent kinetic energy and temperature variance. In view of the low Richardson numbers at stake (Ri _f < 0.03), the buoyancy forces appeared logically to be quantitatively negligible compared to the main driving forces, but such a low-energy forcing mechanism was in fact sufficient in unstable configurations to increase the shear stress and the expansion rate of the mixing layer significantly, both phenomena being associated with enhanced production of turbulence.     

Flow field characterization of coaxial conical and serrated (chevron) nozzles

PIV measurements were performed to provide insight into the effect of serrated (chevron) nozzles on the flow field of a coaxial circular jet. The serrations were tested on the primary nozzle. Mean flow results showed that the chevron effectively redistributes momentum from the high velocity center stream outward to the lower velocity secondary stream by creating lateral jets. This leads to a more rapid decay of the peak jet velocity and a consequent reduction in the length of the jet potential core. Local increases of up to 65% in the outer stream velocity were measured. The interaction of the secondary jets with the lower velocity outer stream produces increases in turbulent kinetic energy (TKE) near the center nozzle lip. These flow field effects correlate with the jet’s acoustic emissions: Reduction of low-frequency noise due to large scale mixing and potential core shortening, and increased high-frequency noise due to increased near-field turbulence.     

稳定分层流动中湍流特性的研究综述

本文总结了近60 年来分层流动中湍流特性研究的成果. 主要从两个方面进行了综述:(1) 分层流动中湍流场的演变和混合. 在这方面主要分析稳定分层对湍流混合和湍流结构的影响, 以及混合层内湍流结构的特性和混合层的演化规律. (2) 分层流动中湍流的扩散和输运. 动量和标量的逆梯度输运特性是分层湍流研究的一个重要方向;分析分层对湍流扩散的影响. 并指出了一些值得今后进一步研究的方向.     

PIV measurements of a turbulent jet issuing from round sharp-edged plate

An experimental investigation is presented of a turbulent jet issuing from a round sharp-edged orifice plate (OP) into effectively unbounded surroundings. Planar measurements of velocity were conducted using Particle Image Velocimetry (PIV) in the near and transition regions. The Reynolds number, based on the jet initial diameter and velocity, is approximately 72,000. The instantaneous and mean velocities, Reynolds normal and shear stresses were obtained. The centerline velocity decay and the half-velocity radius were derived from the mean velocity. It is revealed that primary coherent structures occur in the near field of the OP jet and that they are typically distributed asymmetrically with respect to the nozzle axis. Comparison of the present PIV and previous hot-wire measurements for the OP jet suggests that high initial turbulence intensity leads to reduced rates of decay and spread of the mean flow field and moreover a lower rate of variation of the turbulence intensity. Results also show that self-similarity of the mean flow is well established from the transition region while the turbulent statistics are far from self-similar within the measured range to 16 diameters.     

Density effects on jet characteristics in confined swirling flow

Density effects on isothermal jet mixing in confined swirling flow are investigated. The experiment is carried out with helium/air as the jet fluid in the same facility as that used by So et al. (1984a, b) and the test conditions are chosen to be the same as before. Contrary to the homogeneous mixing results, the helium jet is preserved up to 40 jet diameters downstream. The behavior of the mean and turbulence field depends highly on the initial jet velocity. Since the jets are fully turbulent and the jet momentum fluxes for inhomogeneous mixing are less than those for homogeneous mixing, the cause of this difference in behavior is directly attributed to the combined action of density difference and swirl. In spite of this, near isotropy of the turbulence field is again observed at 40 jet diameters downstream.     

A turbulent boundary layer over a two-dimensional rough wall

Particle image velocimetry (PIV) measurements and planar laser induced fluorescence (PLIF) visualizations have been made in a turbulent boundary layer over a rough wall. The wall roughness consisted of square bars placed transversely to the flow at a pitch to height ratio of λ/k = 11 for the PLIF experiments and λ/k = 8 and 16 for the PIV measurements. The ratio between the boundary layer thickness and the roughness height k/δ was about 20 for the PLIF and 38 for the PIV. Both the PLIF and PIV data showed that the near-wall region of the flow was populated by unstable quasi-coherent structures which could be associated to shear layers originating at the trailing edge of the roughness elements. The streamwise mean velocity profile presented a downward shift which varied marginally between the two cases of λ/k, in agreement with previous measurements and DNS results. The data indicated that the Reynolds stresses normalized by the wall units are higher for the case λ/k = 16 than those for λ/k = 8 in the outer region of the flow, suggesting that the roughness density effects could be felt well beyond the near-wall region of the flow. As expected the roughness disturbed dramatically the sublayer which in turn altered the turbulence production mechanism. The turbulence production is maximum at a distance of about 0.5k above the roughness elements. When normalized by the wall units, the turbulence production is found to be smaller than that of a smooth wall. It is argued that the production of turbulence is correlated with the form drag.     

Analysis and Modeling of the Turbulent Diffusion of Turbulent Kinetic Energy in Natural Convection

Buoyant flows often contain regions with unstable and stable thermal stratification from which counter gradient turbulent fluxes are resulting, e.g. fluxes of heat or of any turbulence quantity. Basing on investigations in meteorology an improvement in the standard gradient-diffusion model for turbulent diffusion of turbulent kinetic energy is discussed. The two closure terms of the turbulent diffusion, the velocity-fluctuation triple correlation and the velocity-pressure fluctuation correlation, are investigated based on Direct Numerical Simulation (DNS) data for an internally heated fluid layer and for Rayleigh–Bénard convection. As a result it is decided to extend the standard gradient-diffusion model for the turbulent energy diffusion by modeling its closure terms separately. Coupling of two models leads to an extended RANS model for the turbulent energy diffusion. The involved closure term, the turbulent diffusion of heat flux, is studied based on its transport equation. This results in a buoyancy-extended version of the Daly and Harlow model. The models for all closure terms and for the turbulent energy diffusion are validated with the help of DNS data for internally heated fluid layers with Prandtl number Pr = 7 and for Rayleigh–Bénard convection with Pr = 0.71. It is found that the buoyancy-extended diffusion model which involves also a transport equation for the variance of the vertical velocity fluctuation gives improved turbulent energy diffusion data for the combined case with local stable and unstable stratification and that it allows for the required counter gradient energy flux.     

An Analysis of Turbulent Motions In and Around a Differentially Forced Density Interface

The Rapid-Distortion-Theory-based analysis proposed by Fernando and Hunt [1] is extended to study the nature of turbulence in and around a density interface sandwiched between turbulent layers with dissimilar properties. It is shown that interfacial motions consist of low-frequency, resonantly excited, nonlinear internal waves and high-frequency, linear internal waves driven by background turbulence. Based on the assumptions that (i) all resonant waves and some nonresonant waves having frequencies close to the resonant frequencies grow rapidly, break, and cause interfacial mixing, (ii) the spectral amplitude of the vertical velocity in the wave-breaking regime is constant, and (iii) kinetic energy is equipartitioned between linear and nonlinear breaking wave regimes, the r.m.s. vertical velocity at the interface and the turbulent kinetic energy flux into the interface are calculated. The migration velocity of the interface is calculated using the additional assumption that the buoyancy flux into a given turbulent layer is a fixed fraction of the turbulent kinetic energy flux supplied to the interface by the same layer. The calculations are found to be in good agreement with the entrainment data obtained in previous laboratory experiments in the parameter regime where the interface is dominated by internal wave dynamics. Received 23 July 1997 and accepted 8 January 1999     

Experimental study of heat flux in mixed convective flow over solid waves

In this experimental study, we address transport processes in a mixed convective flow over a heated wavy surface. Therefore, we combine digital particle image velocimetry (DPIV) and two-color planar laser induced fluorescence (PLIF) to simultaneously measure the velocity and temperature field. For this, we propose to use the dye combination Rhodamine B and Rhodamine 110, both excited with the Nd:YAG laser also used for the PIV measurements. We investigate the influence of mixed convection over a wavy surface on the velocity field, turbulence statistics, the temperature field and the heat flux. By computing these quantities we find a correlation between the maximum in the Reynolds stress profiles and the components of the heat flux vector, thus regions of maximum momentum and scalar transport coincide. In addition, we apply a proper orthogonal decomposition (POD) to extract the most dominant flow structures in a measurement plane above the wavy surface. This first POD mode is identified as streamwise-oriented, counter-rotating vortices whose spanwise scaling is also correlated with the maximum of heat flux.     

PIV measurements of turbulent flow in planar mixing layer

A turbulent mixing layer consists of two different flow types, i.e. shear layer (shear-flow turbulence) and free stream regions (nearly homogeneous turbulence). The inherent non-uniform seeding tracer distributions observed around the interfaces between the shear layer and two free stream regions usually lead to a difficulty in particle image velocimetry (PIV) measurements. A parametric study on the application of PIV to the measurement of velocity field in a planar mixing layer is made by means of six factors, including interrogation window size, aspect ratio of interrogation window, interrogation window offset, threshold of data validation, sharpening spatial filters (Prewitt and Sobel masks), and smoothing spatial filter (median mask). The objective of this study is to obtain accurate turbulent measurements in both mean and fluctuating velocities using PIV under an appropriate parametric setting. The optimal levels, which are trade-off in between the accuracy and fine spatial resolution of velocity field measurements, are determined with the aid of the Taguchi method. It is shown that the PIV measurements made with this optimal set of parameters are in good agreement with the measurements made by a two-component hot-wire anemometer. Case independency of the proposed optimal set of parameters on the flow condition of the mixing layer is validated through the applications to two additional tests under the different experimental conditions in changing solely either velocity ratio of high-speed to low-speed free stream velocities or Reynolds number.     

Similarity solutions of round jets and plumes

Theκ-εturbulence model,considering the effect of buoyancy on turbulentkinetic energy and its dissipation rate,is adopted to present a mathematical model forround plumes and jets.There are similarity solutions in the uniform environment.Taking into account the conservation of momentum and heat flux.Finite AnalyticMethod is applied to obtain the similarity functions of velocity,temperature andturbulent kinetic energy.The agreement between the calculated and experimental datais good.     

A possible explanation of countergradient fluxes in homogeneous turbulence

This study addresses the phenomenon of persistent countergradient (PCG) fluxes of momentum and heat (density) as observed in homogeneous turbulence forced by shear and stratification. Countergradient fluxes may occur at large scales when stratification is strong. However, they always occur at small scales, independently of stratification. A conceptional model is introduced to explain PCG fluxes at small scales as the result of the collision of large-scale fluid parcels. The large parcels collide under the driving force of inclined vortex structures (in a shear-dominated flow) or of buoyancy (in a strongly stratified shear flow). This collision model also explains the PCG heat flux in an unsheared stratified flow with zero average momentum flux. It is found that the energy of the small-scale PCG motions is provided (i) by quick transport of kinetic energy from the scales of production to relatively slowly dissipating scales if the flow is shear-driven and (ii) by conversion of available potential energy to kinetic energy at small scales when the flow is stratified. The collision mechanism is an inherent property of the turbulence dynamics. Therefore, the PCG fluxes at small scales reflect a universal character of homogeneous turbulence, and are found over a large range of Reynolds numbers. The Prandtl (or Schmidt) number influences the rate of dissipation of temperature (or density) variance but not the dissipation rate of the velocity variance. In stratified flows, therefore, the number directly affects the strength of the PCG heat flux at small scales. It is found, however, that the PCG momentum flux is also altered slightly when the Prandtl number is large enough to sustain small buoyantly moving parcels after collision.     

Accuracy of tomographic particle image velocimetry data on a turbulent round jet

Tomographic particle image velocimetry (Tomo-PIV) was applied on a turbulent round air jet to quantitatively assess the accuracy of velocity gradients obtained in the self-similar turbulent region. The jet Reynolds number based on the nozzle diameter (d) was Re_d = 3000. Mean velocity, turbulent intensities, and Reynolds shear stress at the center plane of the jet were measured. In addition, statistical results of Tomo-PIV along the axial direction were assessed by performing a separate set of two-dimensional two-component PIV experiments on a “side view” plane along the jet axis. Moreover, the probability distribution functions of four components of the measured velocity gradients in the axial and radial directions were validated by these “side view” planar PIV data. The root mean square of the velocity divergence values relative to the norm of the velocity gradient tensor was 0.36. Furthermore, the on- and off-diagonal components of the velocity gradients satisfied the axisymmetric isotropy conditions. The divergence error in the data affected only areas with low gradient magnitude. Therefore, turbulent structures in the regions with intense vorticity and dissipation can be closely monitored. On this basis, the joint pdfs of the invariants of the velocity gradient and strain and rotation tensor rates were produced and compared well with those in isotropic turbulence studies.     

Buoyancy effects on turbulent swirling flows

A three-parameter model of turbulence applicable to free boundary layers has been developed and applied for the prediction of axisymmetric turbulent swirling flows in uniform and stagnant surroundings under the action of buoyancy forces. The turbulent momentum and heat fluxes appearing in the time-averaged equations for the mean motion have been determined from algebraic expressions, derived by neglecting the convection and diffusion terms in the differential transport equations for these quantities, which relate the turbulent fluxes to the kinetic energy of turbulence, k, the dissipation length scale of turbulence, L, and the temperature covariance, T ′². Differential transport equations have been used to determine these latter quantities. The governing equations have been solved using fully implicit finite difference schemes. The turbulence model is capable of reproducing the gross features of pure jet flows, buoyant flows and swirling flows for weak and moderate swirl. The behaviour of a turbulent buoyant swirling jet has been found to depend solely on exit swirl and Froude numbers. The predicted results indicate that the incorporation of buoyancy can cause significant changes in the behaviour of a swirling jet, particularly when the buoyancy strength is high. The jet exhibits similarity behaviour in the initial region for weak swirl and weak buoyancy strengths only, and the asymptotic case of a swirling jet under the action of buoyancy forces is a pure plume in the far field. The predicted results have been found to be in satisfactory agreement with the available experimental data and in good qualitative agreement with other predicted results.