Reynolds number effects on the behavior of a non-buoyant round jet

The behavior of a non-buoyant circular water jet discharged from a contraction nozzle was experimentally investigated. In this experiment, the Reynolds number of the jet, based on the mean velocity results obtained by particle image velocimetry (PIV), ranged from 177 to 5,142. From the experimental results, we found that the cross-sectional profile of the axial velocity for a laminar flow near the nozzle did not show a top-hat distribution, whereas the profiles with Reynolds number higher than 437 were almost top-hat. The length of the zone of flow establishment (ZFE) was found to decrease with increasing Reynolds number. The measured centerline velocity decayed more rapidly and, consequently, approached the theoretical equation earlier near the nozzle as the Reynolds number increased. The decay constant for the centerline velocity of the turbulent cases was relatively lower than that discovered in theory. It is assumed that this probably resulted from the use of the contraction nozzle. Verifying the similarity of the lateral velocity profiles demonstrated that the Gaussian curve was properly approximated only for the turbulent jets and not for the laminar or transitional flows. The jet half width seldom grew for the laminar or transitional flows, whereas it grew with increasing axial distance for the turbulent flows. The spreading rates for the turbulent flows gradually decreased with increasing Reynolds number. The normalized turbulence intensity along the jet centerline increased more rapidly with the axial distance as the Reynolds number increased, and tended to the constant values proposed by previous investigators. The Reynolds shear stress levels were also found to increase as the Reynolds number increased for the turbulent jets.     

Moderate Reynolds number axisymmetric jet development downstream an extended conical diffuser: Influence of extension length

Low-velocity (bulk velocity of 4.4 m/s) and moderate Reynolds (7350) axisymmetrical jet development is studied by hot-film single sensor anemometry. The jet issues from a conical convergent-divergent diffuser with uniform extension (diameter 25 mm). Decreasing the length-to-diameter ratio of the extension tube from 20 down to 0.4 is shown to alter severely the mean velocity profile at the tube outlet from Blasius to top-hat whereas turbulence intensities increases from 6 up to 50%. Next, the influence of the initial velocity profile at the tube outlet on axisymmetrical jet development is assessed. The velocity development exhibits a self-similar far field characteristic for axisymmetrical jet development. Although, the jet centerline decay constant increases and the jet spreading rate decreases as length-to-diameter ratios are increased from 0.4 up to 7.2 for which the initial centerline velocity decreases. Therefore, scaling of the centerline decay constant and inverse scaling of the spreading rate with initial centerline velocity U₀ or initial velocity Reynolds number Re₀ reported for moderate Reynolds numbers and low initial turbulence levels [18,22] does not hold as the turbulence level exceeds a threshold value in the range 12–27%. In addition, the influence of initial conditions on near and far field turbulence properties is shown. A transition in near field behaviour is observed for length-to-diameters around 3.6. Flow and geometrical configurations under study are relevant to e.g. upper airway flow.     

Flow field characterization of coaxial conical and serrated (chevron) nozzles

PIV measurements were performed to provide insight into the effect of serrated (chevron) nozzles on the flow field of a coaxial circular jet. The serrations were tested on the primary nozzle. Mean flow results showed that the chevron effectively redistributes momentum from the high velocity center stream outward to the lower velocity secondary stream by creating lateral jets. This leads to a more rapid decay of the peak jet velocity and a consequent reduction in the length of the jet potential core. Local increases of up to 65% in the outer stream velocity were measured. The interaction of the secondary jets with the lower velocity outer stream produces increases in turbulent kinetic energy (TKE) near the center nozzle lip. These flow field effects correlate with the jet’s acoustic emissions: Reduction of low-frequency noise due to large scale mixing and potential core shortening, and increased high-frequency noise due to increased near-field turbulence.     

Measurements in the near flow field of an isosceles triangular turbulent free jet

The near field mean flow and turbulence characteristics of a turbulent jet of air issuing from a sharp-edged isosceles triangular orifice into still air surroundings have been examined experimentally using hot-wire anemometry and a pitot-static tube. For comparison, some measurements were made in an equilateral triangular free jet and in a round free air jet, both of which also issued from sharp-edged orifices. The Reynolds number, based on the orifice equivalent diameter, was 1.84×10⁵ in each jet. The three components of the mean velocity vector, the Reynolds normal and primary shear stresses, the one-dimensional energy spectra of the streamwise fluctuating velocity signals and the mean static pressure were measured. The mean streamwise vorticity, the half-velocity widths, the turbulence kinetic energy and the local shear in the mean streamwise velocity were obtained from the measured data. It was found that near field mixing in the equilateral triangular jet is faster than in the isosceles triangular and round jets. The mean streamwise vorticity field was found to be dominated by counter-rotating pairs of vortices, which influenced mixing and entrainment in the isosceles triangular jet. The one-dimensional energy spectra results indicated the presence of coherent structures in the near field of all three jets and that the equilateral triangular jet was more energetic than the isosceles triangular and round jets.     

The near-field characteristics of circular jets at low Reynolds numbers

An experimental study has been undertaken to investigate the effect of Reynolds number on the near-field region of circular turbulent air jets. Measurements were made using a two-component Laser Doppler Anemometer, and included mean velocity, turbulence intensity, skewness factor, flatness factors and power spectrum. Measurements were taken up to 10 nozzle exit diameter in the downstream direction for different exit Reynolds numbers in the range of 1400 to 20000. The Reynolds number was found to have a strong effect on the jet flow behavior in the near-field region; the centerline velocity decays faster (decay constant = 6.11 for Re = 19400, = 1.35 for Re 1430) and the potential core gets shorter with decreasing Reynolds number. Profile measurements of the skewness and flatness factors indicate that the jet flow becomes more intermittent with decreasing Reynolds number. Power spectrum measurements of the streamwise fluctuating velocities reflects the high energy content of the high Reynolds number jet. It also reveals that there is greater energy at the higher frequencies with increasing Reynolds number.     

Experimental investigation on the similarity of a 3D rectangular turbulent jet

 The paper presents an experimental investigation of turbulent jets issuing from rectangular nozzles. Nozzles with aspect ratios between 3 and 10 were used. Eight different initial conditions were studied. The following jet parameters were measured and evaluated: mean velocity components, jet boundaries, jet momentum, jet entrainment, turbulence intensities and Reynolds stresses. A DISA 55M thermoanemometer and a data acquisition system BE256 were used. The influence of the initial conditions on the similarity of the flow was determined with respect to the mean axial velocity, turbulence intensity and the Reynolds stresses. A significant influence of the initial conditions on the flow structure was observed. The possibility for jet control is discussed and suggestions are given about the need to investigate different parameters. Received: 25 November 1996/Accepted: 30 October 1997     

Phase-locked analysis of velocity fluctuations in a turbulent free swirling jet after vortex breakdown

Large-scale organized vortical structures were studied experimentally in a free swirling jet of air experiencing vortex precession (PVC) at ambient conditions. Detailed measurements were performed in the region near the nozzle exit using phase-locked LDV and PIV, at a Reynolds number of Re ?? 24,400 and a swirl parameter S ?? 1.0. The investigation allowed reconstruction of the time-averaged flowfield, with the associated distribution of turbulent fluctuations, the phase-locked structure of the jet and the associated precessing vortex structure. An original joint analysis of power spectra and probability density functions of velocity data led to quantification of the PVC effect on turbulent fluctuations. This analysis showed that the PVC contribution can be properly separated from the background random turbulence, reproducing the results of phase-locked measurements. It is found that the background turbulence in the near field is substantially weaker if compared to the coherent fluctuations induced by vortex precession.     

Impact of density stratification on the global mode in a swirling jet: Stochastic modelling and Lagrangian coherent structures

In an experimental investigation, the stochastic dynamics of the global mode in a turbulent swirling jet are considered. From the application of the swirling jet in gas turbine combustors, it was observed that a specific density gradient in the flow leads to a suppression of the global mode. This phenomenon was replicated in a generic swirling jet using an electrical heating coil placed inside the breakdown bubble. In the present investigation, the dynamics of the global mode obtained from PIV and pressure measurements are analysed using a stochastic reduced-order model to describe the instability. The stochastic model is necessary to explain the interaction between the deterministic dynamics of the global mode and the perturbations by the background turbulence. The calibration of the stochastic model provides the amplification rate of the global mode that defines the transition of the flow, dependent on the swirling strength and the density difference. The spatial structure of the global mode is further investigated from Lagrangian coherent structures of the flow field which are computed from the 3D time-resolved velocity field reconstruction based on planar PIV measurements. The Lagrangian visualisations and schlieren visualisations are used to explain the absence of the density effects on the global mode at larger Reynolds numbers. The analysis gives a detailed view of the stochastic dynamics of a hydrodynamic instability in a turbulent flow.     

Mean Flow and Turbulence Measurements in a Turbulent Free Cruciform Jet

The results of measurements of all three components of the mean velocity vector, the Reynolds normal and primary shear stresses and the mean static pressure in a turbulent free jet, issuing from a sharp-edged cruciform orifice, are presented in this paper. The measurements were made with an x-array hot-wire probe and a pitot-static tube in the near flow field of the jet. The Reynolds number, based upon the equivalent diameter of the orifice, was 1.70 × 10⁵. In addition to the quantities measured directly, the mean streamwise centreline velocity decay, the jet half-velocity widths, the jet spreading rate, the mean streamwise vorticity, the mass entrainment rate, the integral momentum flux and the one-dimensional energy spectra have been derived from the measured data. The results show that the mean streamwise centreline velocity decay rate of the cruciform jet is higher than that of a round jet issuing from an orifice with the same exit area as that of the cruciform orifice. The mean streamwise velocity field changed shape continuously from a cruciform close to the orifice exit plane to circular at 12 and half equivalent diameters downstream. The mean streamwise vorticity field, up to about three equivalent diameters downstream of the orifice exit plane, consists of four pairs of counter-rotating cells, which are aligned with the four edges in the centre of the cruciform orifice.     

On Turbulent Jets Issuing from Notched-Rectangular and Circular Orifice Plates

This paper reports an experimental investigation of the near-field flow characteristics of two air/air turbulent jets issuing respectively from notched-rectangular and circular orifice plates with identical opening areas or equivalent diameters (D _e ). Planar particle image velocimetry (PIV) was used to measure the velocity field at the same Reynolds number, based on D _e , of Re = 72,000. Consistent with previous work on other noncircular jets, the present study finds that the notched jet has a higher rate of mixing than does the circular counterpart. In particular, this jet in the very near field transfers its momentum to the surroundings at a greater rate, evidenced by a notably shorter unmixed core and faster turbulence intensity growth. The higher rates of overall decay and spread of the notched jet are maintained over the entire measurement region and likely beyond. In addition, the phenomenon of axis switching is also found to occur in this jet.     

Dynamic wind loads and wake characteristics of a wind turbine model in an atmospheric boundary layer wind

An experimental study was conducted to characterize the dynamic wind loads and evolution of the unsteady vortex and turbulent flow structures in the near wake of a horizontal axis wind turbine model placed in an atmospheric boundary layer wind tunnel. In addition to measuring dynamic wind loads (i.e., aerodynamic forces and bending moments) acting on the wind turbine model by using a high-sensitive force-moment sensor unit, a high-resolution digital particle image velocimetry (PIV) system was used to achieve flow field measurements to quantify the characteristics of the turbulent vortex flow in the near wake of the wind turbine model. Besides conducting “free-run” PIV measurements to determine the ensemble-averaged statistics of the flow quantities such as mean velocity, Reynolds stress, and turbulence kinetic energy (TKE) distributions in the wake flow, “phase-locked” PIV measurements were also performed to elucidate further details about evolution of the unsteady vortex structures in the wake flow in relation to the position of the rotating turbine blades. The effects of the tip-speed-ratio of the wind turbine model on the dynamic wind loads and wake flow characteristics were quantified in the terms of the variations of the aerodynamic thrust and bending moment coefficients of the wind turbine model, the evolution of the helical tip vortices and the unsteady vortices shedding from the blade roots and turbine nacelle, the deceleration of the incoming airflows after passing the rotation disk of the turbine blades, the TKE and Reynolds stress distributions in the near wake of the wind turbine model. The detailed flow field measurements were correlated with the dynamic wind load measurements to elucidate underlying physics in order to gain further insight into the characteristics of the dynamic wind loads and turbulent vortex flows in the wakes of wind turbines for the optimal design of the wind turbines operating in atmospheric boundary layer winds.     

Experimental investigation on a turbulence generation system with high-blockage plates

An experimental study was conducted to develop and characterize systematically a new turbulence generator system to yield large turbulent Reynolds numbers in a compact configuration. The effect of the geometric parameters of two families of high-blockage plates on the resulting turbulent flow field was systematically studied: one series of plates was characterized by the number and distribution of circular openings; a second series had non-circular opening(s) with different shapes, distribution and position of the opening(s). The plates were placed upstream of a contoured contraction and the near field at the centerline of the resulting turbulent free jet was characterized by hot-wire anemometry in terms of mean axial velocity, turbulence intensity, turbulence length scales and corresponding Reynolds numbers. The plate with a central, non-circular opening produced the best compromise of highest turbulence levels along with excellent uniformity in average velocity and turbulence intensity, as evidenced by scan in the transverse direction. It appears to be the most promising one. By comparison with more traditional approaches to turbulence generation, we increased the turbulent Reynolds numbers based on the integral length scale to values on the order of 1000, which was one of the design objectives. Other plate geometries also yielded intense turbulence, but, in some cases, exhibited spurious frequency peaks in their power spectrum. The turbulent generation approach is to be adapted to combustion studies to reproduce conditions typical of practical system in relatively small experimental set-ups that are well-suited for bench-top experiments.     

Turbulent structure during transition to self-similarity in a round jet

 The developing turbulent region of a round jet was investigated using an improved implementation of digital particle image velocimetry (DPIV). The two-dimensional flow field in planes normal and parallel to the axial velocity was measured at locations between 15 and 30 diameters downstream, for two Reynolds numbers of 5500 and 16,000. The study consisted of instantaneous snapshots of the velocity and vorticity fields as well as measurements of velocity correlations up to third order. In this regime, the Reynolds number had a significant effect on both the instantaneous flow structure and the profiles of mean velocity across the jet. Coherent streamwise structures were present in the jet core for the lower Reynolds number. Additional structures whose evolution was governed by time scales two orders of magnitude larger than the convective scale inside the jet were observed in the entrainment field. The velocity correlations provided further support for the validity of DPIV turbulence measurements. The data was consistent with the equations of motion and momentum was conserved. DPIV measurements of turbulent kinetic energy components agreed with the hot-wire measurements of previous studies. Received: 27 November 1996/Accepted: 14 July 1997     

Highly-resolved LES and PIV Analysis of Isothermal Turbulent Opposed Jets for Combustion Applications

Turbulent opposed jet (TOJ) burners are an interesting test case for fundamental combustion research and a good benchmark for the available modelling approaches. However, these opposed jet flames strongly depend on the turbulence generation inside the nozzle, which is usually achieved through a perforated plate upstream of the nozzle exit. The present work investigates the flow from these perforated plates and the subsequent turbulence generation in great detail. We present results from highly-resolved large eddy simulations (LES) of the in-nozzle flow in turbulent opposed jets alongside state-of-the-art particle image velocimetry (PIV) at standard and high repetition rates taken inside a glass nozzle. The in-nozzle PIV data provides the LES inflow conditions with unprecedented detail, which are used to follow the initial jet development behaviour known from PIV, before jet coalescence, turbulence production and decay further downstream in the nozzles are successfully predicted. In regions where the PIV experiment suffers from inherent limitations like reflections and the velocity bias, the LES data is available to still obtain a detailed picture of the flow. The sensitivity of the simulations to various physical and numerical parameters is discussed in detail. Results from LES and PIV are compared qualitatively and quantitatively in terms of first and second moments of velocity, temporal autocorrelations, and energy density spectra. Significant deviations are found in the frequency (20%) and strength of vortex shedding from the inlet plane only, whereas the qualitative and quantitative agreement between simulation and experiment is otherwise excellent throughout, implying that a successful large eddy simulation of a turbulent opposed jet can be performed in a domain that includes the perforated plates.     

狭缝射流撞击圆柱表面的湍流特性实验研究

实验研究了狭缝射流撞击圆柱表面后壁面射流区的平均流动和湍流特 性. 考察了雷诺数 Re (6000-20000), 喷口到受撞表面距 离 Y/W (5-13), 喷口宽度 W (6.25mm, 9.38mm), 受撞表 面曲率(半圆柱体直径 D = 150mm)对流动和湍流结构的影响. 通过分析 X 热线 在壁面射流区的测量结果发现，在近壁区域，表面曲率、 Re_{w} , Y/W 和 S/W 等 参数对 \sqrt {\overline{u^2}} / U_m 的影响比对 \sqrt {\overline{v^2}} / U_m 强，并且切 应力 \overline {uv} /U_m^2 对表面曲率变化最敏感. 当喷口与受撞击表面之间的距 离 Y/W 在一定范围内增加时， 沿圆柱表面流动的流向和横向的湍流强度增强. 用平板射流和圆柱体表面壁面射流的数据进行比较，从而得到表面曲率对壁面射流特 性的影响. 结果表明，曲率对壁面射流的影响较强， 并随着 S/W 的增大而增强. 随着雷诺数的增大，壁面曲率的影响也有强化的趋势.     

Time-resolved PIV measurements of the interaction of polystyrene beads with near-wall-coherent structures in a turbulent channel flow

Time-resolved PIV measurements were performed in a dilute particle-laden flow tracking near-neutrally buoyant polystyrene beads and the velocity field of a near wall turbulent boundary layer. Data were taken in a vertical light sheet aligned in the streamwise direction at the center of a horizontal, closed loop, transparent square water channel facility. In addition, low speed measurements were performed characterizing the effects of the dispersed phase on mean and turbulence flow quantities. Reynolds shear stress slightly differed from clear water conditions whereas fluid mean and rms values were not affected. A case study for several beads revealed a clear relation between their movement and near-wall coherent structures. Several structures having 2D vorticity signatures of near-wall hairpin vortices and hairpin packets, directly affected bead movement. A statistical analysis showed that the mean streamwise velocity of ascending beads lagged behind the mean fluid velocity and bead rms values were higher than fluid ones. Particle Reynolds numbers based on the magnitude of the instantaneous relative velocity vector peaked near the wall; values not exceeding 100, too low for vortex shedding to occur. Quadrant analysis showed a clear preference for ascending beads to reside in ejections while for descending beads the preference for sweeps was less.     

Near-Wake Turbulence Properties around a Circular Cylinder at High Reynolds Number

The present study investigates the turbulent properties of the flow around a circular cylinder in the near-wake and in the near-wall upstream region at the Reynolds number 140,000. A detailed cartography of the mean and turbulent velocity fields using a moderate blockage and aspect ratio is provided in order to use the present results for direct comparisons with realisable 3D Navier-Stokes computations. The flow structure is analysed by means of two experiments using respectively the LDV and the PIV techniques, both providing a refined grid of measurement points. The dynamics of the separation region, the growth and decay of turbulence in the near wake, as well as the spatial growth of the organised mode are analysed.     

Control of diffuser jet flow: turbulent kinetic energy and jet spreading enhancements assisted by a non-thermal plasma discharge

An axisymmetric air jet exhausting from a 22-degree-angle diffuser is investigated experimentally by particle image velocimetry (PIV) and stereo-PIV measurements. Two opposite dielectric barrier discharge (DBD) actuators are placed along the lips of the diffuser in order to force the mixing by a co-flow actuation. The electrohydrodynamic forces generated by both actuators modify and excite the turbulent shear layer at the diffuser jet exit. Primary air jet velocities from 10 to 40 m/s are studied (Reynolds numbers ranging from 3.2 to 12.8 × 10⁴), and baseline and forced flows are compared by analysing streamwise and cross-stream PIV fields. The mixing enhancement in the near field region is characterized by the potential core length, the centreline turbulent kinetic energy (TKE), the integrated value of the TKE over various slices along the jet, the turbulent Reynolds stresses and the vorticity fields. The time-averaged fields demonstrate that an effective increase in mixing is achieved by a forced flow reattachment along the wall of the diffuser at 10 m/s, whereas mixing enhancement is realized by excitation of the coherent structures for a primary velocity of 20 and 30 m/s. The actuation introduces two pairs of contra-rotating vortices above each actuator. These structures entrain the higher speed core fluid toward the ambient air. Unsteady actuations over Strouhal numbers ranging from 0.08 to 1 are also studied. The results suggest that the excitation at a Strouhal number around 0.3 is more effective to enhance the turbulence kinetic energy in the near-field region for primary jet velocity up to 30 m/s.     

Particle image velocimetry investigation on mixing enhancement of non-circular sharp edge nozzles

An experimental study using Particle Image Velocimetry (PIV) on free jets issuing from different orifice plate (OP) nozzles is reported. Mean velocity, turbulence intensity and higher order profiles relevant for large and small scale mixing are considered in the near field and interaction zone (0 < X/D < 20). This is done to determine mixing enhancement due to rectangular, squared, elliptic and triangular nozzles in comparison to circular nozzle results in two orthogonal planes. The effect of Reynolds number on the differences among the nozzle shapes is also considered by performing measurements just after laminar–turbulent transition (Re = 8000) and in the fully turbulent regime (Re = 35,000). The results at low Reynolds number show two classes of jets, i.e. at one side, those closer to axial-symmetric conditions, as circular, square and triangular jets, whereas on the other side those with elongated nozzles as rectangular and elliptic. The reason for the different behavior of the latter is connected to the phenomenon of axis-switching which allows a rearrangement of turbulence over the different velocity components and directions. However, for the highest Reynolds number investigated, all nozzles show similar behavior especially in the jet far field (X/D > 10), thus suggesting a significant Reynolds number dependence of the results.